Comment 19 for bug 1143495

Also affected by this. I'm running Debian 8.9 up to date.

(Linux phlsys 3.16.0-4-amd64 #1 SMP Debian 3.16.43-2+deb8u3 (2017-08-15) x86_64 GNU/Linux)

syslog shows : (each 10mn)

Aug 26 07:02:06 phlsys udisksd[2161]: Error performing housekeeping for drive /org/freedesktop/UDisks2/drives/ST1000DM003_1SB10C_W9A07ER1: Error updating SMART data: sk_disk_check_sleep_mode: Operation not supported (udisks-error-quark, 0)

GSmartControl doesn't show any error.

Output of smartctl:

=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.14 (AF)
Device Model: ST1000DM003-1SB10C
Serial Number: W9A07ER1
LU WWN Device Id: 5 000c50 08b7c0db3
Firmware Version: CC41
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Sat Aug 26 08:07:50 2017 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
     was never started.
     Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
     without error or no self-test has ever
     been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
     Auto Offline data collection on/off support.
     Suspend Offline collection upon new
     command.
     No Offline surface scan supported.
     Self-test supported.
     Conveyance Self-test supported.
     Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
     power-saving mode.
     Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
     General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 103) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x10a5) SCT Status supported.
     SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate 0x000f 083 066 006 Pre-fail Always - 201611737
  3 Spin_Up_Time 0x0003 098 097 000 Pre-fail Always - 0
  4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 259
  5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
  7 Seek_Error_Rate 0x000f 100 253 045 Pre-fail Always - 999312
  9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 704
 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 68
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 0 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 069 057 040 Old_age Always - 31 (Min/Max 23/33)
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 262
194 Temperature_Celsius 0x0022 031 016 000 Old_age Always - 31 (0 16 0 0 0)
195 Hardware_ECC_Recovered 0x001a 010 006 000 Old_age Always - 201611737
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 75h+17m+42.252s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 1749229928
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 1409020289

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
    1 0 0 Not_testing
    2 0 0 Not_testing
    3 0 0 Not_testing
    4 0 0 Not_testing
    5 0 0 Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.