Comment 221 for bug 401126

Here's the error output. Ran for about 20 mins on battery before failing. "richmond" is my wireless router essid

rtl819xSE 0000:09:00.0: firmware: requesting RTL8192SE/rtl8192sfw.bin
rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1
===>rtllib_start_scan()
ADDRCONF(NETDEV_UP): wlan0: link is not ready
[drm:drm_mode_rmfb] *ERROR* tried to remove a fb that we didn't own
[drm:drm_mode_rmfb] *ERROR* tried to remove a fb that we didn't own
[drm:drm_mode_getfb] *ERROR* invalid framebuffer id
executing set pll
executing set crtc timing
[drm] LVDS-9: set mode 1366x768 31
executing set pll
executing set crtc timing
[drm] TV-11: set mode 1600x1200 35
executing set pll
executing set crtc timing
[drm] TV-11: set mode 1600x1200 34
Unpin not necessary for ffff88012ad94800 !
eth0: no IPv6 routers present
type=1305 audit(1265724419.355:21288): auid=4294967295 ses=4294967295 subj=kernel op="remove rule" key=(null) list=4 res=1
type=1305 audit(1265724419.356:21289): audit_enabled=0 old=1 auid=4294967295 ses=4294967295 subj=kernel res=1
hda-intel: IRQ timing workaround is activated for card #1. Suggest a bigger bdl_pos_adj.
rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1
executing set pll
executing set crtc timing
[drm] TV-11: set mode 36
fuse init (API version 7.12)
rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1
alg name:WEP
Linking with richmond,channel:9, qos:0, myHT:1, networkHT:0, mode:6 cur_net.flags:0x406
Linking with richmond,channel:9, qos:0, myHT:1, networkHT:0, mode:6 cur_net.flags:0x406
===>rtllib_associate_procedure_wq(), chan:9
HTSetConnectBwMode():pHTInfo->bCurBW40MHz:0
rtllib_authentication_req():auth->algorithm is OPEN
rtl8192_SetWirelessMode(), wireless_mode:4, bEnableHT = 0
Associated successfully
normal associate
Using G rates:108
Successfully associated, ht not enabled(0, 0)
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
DHCP pkt src port:68, dest port:67!!
dm_check_edca_turbo():iot peer is unknown, bssid:00:13:10:8c:0c:44
wlan0: no IPv6 routers present
hrtimer: interrupt too slow, forcing clock min delta to 3942369 ns
CE: hpet increasing min_delta_ns to 15000 nsec
rtl819xSE:Err RX pkt len = 0x15

rtl819xSE:Err RX pkt len = 0x16

rtl819xSE:Err RX pkt len = 0x14

[drm:radeon_vga_detect] *ERROR* VGA-1: probed a monitor but no|invalid EDID
[drm:edid_is_valid] *ERROR* Raw EDID:
<3>20 20 00 00 00 fc 00 53 79 6e 63 4d 61 73 74 65 .....SyncMaste
<3>72 0a 20 20 00 00 00 ff 00 48 56 46 4c 42 30 34 r. .....HVFLB04
<3>37 37 30 0a 20 20 00 7b ff ff ff ff ff ff ff ff 770. .{........
<3>ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
<3>ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
<3>ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
<3>ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
<3>ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................

i2c-adapter i2c-1: readbytes: ack/nak timeout
usb 1-2: USB disconnect, address 3
FAT: bread failed in fat_clusters_flush
FAT: bread failed in fat_clusters_flush
FAT: bread failed in fat_clusters_flush
FAT: bread failed in fat_clusters_flush
rtl819xSE:Err RX pkt len = 0x17

dis associate packet!
alg name:WEP

Linking with richmond,channel:9, qos:0, myHT:0, networkHT:0, mode:6 cur_net.flags:0x406
===>rtllib_associate_procedure_wq(), chan:9
HTSetConnectBwMode():pHTInfo->bCurBW40MHz:0
rtllib_authentication_req():auth->algorithm is OPEN
Linking with richmond,channel:9, qos:0, myHT:0, networkHT:0, mode:6 cur_net.flags:0x406
===>rtllib_associate_procedure_wq(), chan:9
HTSetConnectBwMode():pHTInfo->bCurBW40MHz:0
rtllib_authentication_req():auth->algorithm is OPEN
rtl8192_SetWirelessMode(), wireless_mode:4, bEnableHT = 0
Associated successfully
normal associate
Using G rates:108
Successfully associated, ht not enabled(0, 0)
DHCP pkt src port:68, dest port:67!!