© 2004
Canonical Ltd.
•
Terms of use
•
Data privacy
•
Contact Launchpad Support
•
Blog
•
Careers
•
System status
•
f33e652
(Get the code!)
Hi.
I have problem with HBA Emulex LPe12000 Fibre channel adapter. It doesn't see disk on direct attach.
[ 4.015493] lpfc 0000:04:00.0: 0:1303 Link Up Event x1 received Data: x1 x1 x10 x2 x0 x0 0
[ 4.015570] lpfc 0000:04:00.0: 0:1309 Link Up Event npiv not supported in loop topology
[ 4.016671] lpfc 0000:04:00.0: 0:(0):2858 FLOGI failure Status:x3/x18 TMO:x0 Data x1000 x0
[ 4.017627] lpfc 0000:04:00.0: 0:(0):2858 FLOGI failure Status:x3/x18 TMO:x0 Data x1000 x0
[ 4.018561] lpfc 0000:04:00.0: 0:(0):2858 FLOGI failure Status:x3/x18 TMO:x0 Data x1000 x0
[ 4.018636] lpfc 0000:04:00.0: 0:(0):0100 FLOGI failure Status:x3/x18 TMO:x0
[ 4.019713] lpfc 0000:04:00.0: 0:(0):0266 Issue NameServer Req x117 err 1 Data: x80000 x0
I have made a little investigation.
Ubuntu 16.04.3 LTS, kernel 4.10.0-28, lpfc 11.2.0.2 - no problem.
Ubuntu 17.10.1, kernel 4.13.0-21, lpfc 11.4.0.1 - problem.
Debian 9.3, kernel 4.9.0-4, lpfc 11.2.0.0 - no problem.
Fedora 27, kernel 4.13.9-300, lpfc 11.4.0.1 - problem.
Proxmox 5.0, kernel 4.10.15-1, lpfc 11.2.0.2 - no problem.
Proxmox 5.1, kernel 4.13.13-5, lpfc 11.4.0.1 - problem.
Another user with this problem said that if fiber switch is added between the server and the storage it's working as expected.
I think problem is in lpfc.ko 11.4.0.1. Any kernel (4.13 now) that has this module version is affected. Broadcom support confirmed that bug and suggested to update module. But Broadcom supports only RHEL and SLES. I tried to compile, but no luck. Please, could you update lpfc.ko module in linux-image-generic package?
There are version 11.4.142.21 for SLES 12 and 11.4.204.11 for RHEL 6 and 7 on Broadcom site.
Thanks.
---
04:00.0 Fibre Channel [0c04]: Emulex Corporation Saturn-X: LightPulse Fibre Channel Host Adapter [10df:f100] (rev 03)
Subsystem: Emulex Corporation Saturn-X: LightPulse Fibre Channel Host Adapter [10df:f100]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 27
Region 0: Memory at fbaff000 (64-bit, non-prefetchable) [size=4K]
Region 2: Memory at fbaf8000 (64-bit, non-prefetchable) [size=16K]
Expansion ROM at fba80000 [disabled] [size=256K]
Capabilities: [58] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Enable- Count=1/16 Maskable+ 64bit+
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [78] MSI-X: Enable- Count=32 Masked-
Vector table: BAR=2 offset=00002000
PBA: BAR=2 offset=00003000
Capabilities: [84] Vital Product Data
Product Name: LPE12000, 8GB/S, 1-PORT FC, PCI EXPRESS HBA, SFP, DIAG, OPTICS, DELL
Read-only fields:
[PN] Part number: LPE12000-M8
[SN] Serial number: FC24751316
[V0] Vendor specific: FC24751316
[V1] Vendor specific: Emulex LPe12000-M8 8Gb PCIe Fibre Channel Adapter
[V2] Vendor specific: LPe12000-M8
[V3] Vendor specific: T2:78,T3:
[V4] Vendor specific:
[RV] Reserved: checksum bad, 20 byte(s) reserved
End
Capabilities: [94] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 2048 bytes, PhantFunc 0, Latency L0s <1us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 25.000W
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
MaxPayload 256 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x8, ASPM L0s, Exit Latency L0s <1us, L1 <64us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCo
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationCom
Equalizatio
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt+ RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [12c v1] Power Budgeting <?>
Kernel modules: lpfc