**************************
What I expected to happen:
**************************
I expect my windows 10 PC to be able to connect to a hotspot if I set one up
**********************
What happened instead:
**********************
It can't connect to the AP
***********************
Logs of when I connect:
***********************
wpa_supplicant[1358]: wlx00c0caab435c: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
... this is the only line that appears in the logs and on the windows machine, I get the very helpful description of "Can't connect"...
******************
What I did so far:
******************
I tried reading about the ap_scan modes what I could find.
The only two references I did find, was:
- that ap_mode is a setting you can set in wpa_supplicant, however, I'm using NetworkManager and I don't find a way to set 'ap_mode=1'
- all other references were bugreports, which led me to here.
I ordered a new Network Card, using a different chipset, to see if the problem persists. Sadly it didn't arrive yet.
Ubuntu 20.04 LTS ARM (Running on a raspberry Pi)
********
Logfile:
********
NetworkManager[ 1345]: <info> [1593736912.7230] policy: auto-activating connection 'hotspot-inside' (37c28408- 978a-48e0- a135-9867e3a45c 64) 1345]: <info> [1593736912.7248] device (wlx00c0caab435c): Activation: starting connection 'hotspot-inside' (37c28408- 978a-48e0- a135-9867e3a45c 64) 1345]: <info> [1593736912.7252] device (wlx00c0caab435c): state change: disconnected -> prepare (reason 'none', sys-iface-state: 'managed') 1345]: <info> [1593736912.7261] manager: NetworkManager state is now CONNECTING 1345]: <info> [1593736912.7449] device (wlx00c0caab435c): state change: prepare -> config (reason 'none', sys-iface-state: 'managed') 1345]: <info> [1593736912.7459] device (wlx00c0caab435c): Activation: (wifi) access point 'hotspot-inside' has security, but secrets are required. 1345]: <info> [1593736912.7460] device (wlx00c0caab435c): state change: config -> need-auth (reason 'none', sys-iface-state: 'managed') 1345]: <info> [1593736912.7530] device (wlx00c0caab435c): state change: need-auth -> prepare (reason 'none', sys-iface-state: 'managed') 1345]: <info> [1593736912.7557] device (wlx00c0caab435c): state change: prepare -> config (reason 'none', sys-iface-state: 'managed') 1345]: <info> [1593736912.7566] device (wlx00c0caab435c): Activation: (wifi) connection 'hotspot-inside' has security, and secrets exist. No new secrets needed. 1345]: <info> [1593736912.7571] Config: added 'ssid' value 'hotspot-inside' 1345]: <info> [1593736912.7572] Config: added 'mode' value '2' 1345]: <info> [1593736912.7573] Config: added 'frequency' value '2412' 1345]: <info> [1593736912.7574] Config: added 'key_mgmt' value 'WPA-PSK WPA-PSK-SHA256 FT-PSK' 1345]: <info> [1593736912.7574] Config: added 'psk' value '<hidden>' 1345]: <info> [1593736912.7575] Config: added 'proto' value 'RSN' 1345]: <info> [1593736912.7575] Config: added 'pairwise' value 'CCMP' 1345]: <info> [1593736912.7576] Config: added 'group' value 'CCMP' 1358]: Note: nl80211 driver interface is not designed to be used with ap_scan=2; this can result in connection failures 1358]: Using interface wlx00c0caab435c with hwaddr 00:c0:ca:ab:43:5c and ssid "hotspot-inside"
NetworkManager[
NetworkManager[
NetworkManager[
NetworkManager[
NetworkManager[
NetworkManager[
NetworkManager[
NetworkManager[
NetworkManager[
NetworkManager[
NetworkManager[
NetworkManager[
NetworkManager[
NetworkManager[
NetworkManager[
NetworkManager[
NetworkManager[
wpa_supplicant[
wpa_supplicant[
******* ******* ******* ******* ******* ** ******* ******* ******* ******* **
NetworkManager Connection definition:
*******
[connection] 978a-48e0- a135-9867e3a45c 64 priority= 5 1593537574
id=hotspot-inside
uuid=37c28408-
type=wifi
autoconnect-
permissions=
timestamp=
[wifi] 00:C0:CA: AB:43:5C blacklist= 00:C0:CA: AB:43:5C; DC:A6:32: 3A:67:FC;
mac-address=
mac-address-
mode=ap
seen-bssids=
ssid=hotspot-inside
[wifi-security]
group=ccmp;
key-mgmt=wpa-psk
pairwise=ccmp;
proto=rsn;
psk=<XXX>
[ipv4]
dns-search=
method=shared
[ipv6] mode=stable- privacy
addr-gen-
dns-search=
method=ignore
[proxy]
******* ******* ******* ******* * ******* ******* ******* *
USB Network Card information:
*******
*-network:1
description: Wireless interface
physical id: 2
bus info: usb@1:1.1
logical name: wlx00c0caab435c
serial: 00:c0:ca:ab:43:5c
capabilities: ethernet physical wireless
configuration: broadcast=yes driver=rtl88XXau ip=10.42.0.1 multicast=yes wireless=IEEE 802.11bgn
(The device is an Alfa AWUS036AC, using the driver https:/ /github. com/aircrack- ng/rtl8812au - Version 5.6.4.2)
******* ******* ******* ***** ******* ******* *****
What I expected to happen:
*******
I expect my windows 10 PC to be able to connect to a hotspot if I set one up
******* ******* ******* * ******* ******* *
What happened instead:
*******
It can't connect to the AP
******* ******* ******* ** ******* ******* ** 1358]: wlx00c0caab435c: CTRL-EVENT- SUBNET- STATUS- UPDATE status=0
Logs of when I connect:
*******
wpa_supplicant[
... this is the only line that appears in the logs and on the windows machine, I get the very helpful description of "Can't connect"...
******************
What I did so far:
******************
I tried reading about the ap_scan modes what I could find.
The only two references I did find, was:
- that ap_mode is a setting you can set in wpa_supplicant, however, I'm using NetworkManager and I don't find a way to set 'ap_mode=1'
- all other references were bugreports, which led me to here.
I ordered a new Network Card, using a different chipset, to see if the problem persists. Sadly it didn't arrive yet.