I am also not able to use USB modem from Huawei. It is a Huawei EC1261 HSIA device.
Following are the o/p of dmesg after device put in port
#dmesg
usb 2-2: USB disconnect, address 3
usb 2-2: new full speed USB device using uhci_hcd and address 4
usb 2-2: New USB device found, idVendor=12d1, idProduct=1446
usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=4
usb 2-2: Product: HUAWEI Mobile
usb 2-2: Manufacturer: HUAÿWEI TECHNOLOGIES
usb 2-2: SerialNumber: ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
usb 2-2: configuration #1 chosen from 1 choice
scsi6 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 6:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 0
sr2: scsi-1 drive
sr 6:0:0:0: Attached scsi CD-ROM sr2
sr 6:0:0:0: Attached scsi generic sg2 type 5
ISO 9660 Extensions: Microsoft Joliet Level 1
ISOFS: changing to secondary root
SELinux: initialized (dev sr2, type iso9660), uses genfs_contexts
and o/p after #modprobe usbserial vendor=0x12d1 product=0x1446
it runs successfully and then
# wvdialconf
Editing `/etc/wvdial.conf'.
Scanning your serial ports for a modem.
ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Modem Port Scan<*1>: S1 S2 S3
Sorry, no modem was detected! Is it in use by another program?
Did you configure it properly with setserial?
I am also not able to use USB modem from Huawei. It is a Huawei EC1261 HSIA device.
Following are the o/p of dmesg after device put in port
#dmesg
usb 2-2: USB disconnect, address 3
usb 2-2: new full speed USB device using uhci_hcd and address 4
usb 2-2: New USB device found, idVendor=12d1, idProduct=1446
usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=4
usb 2-2: Product: HUAWEI Mobile
usb 2-2: Manufacturer: HUAÿWEI TECHNOLOGIES
usb 2-2: SerialNumber: ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
usb 2-2: configuration #1 chosen from 1 choice
scsi6 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 6:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 0
sr2: scsi-1 drive
sr 6:0:0:0: Attached scsi CD-ROM sr2
sr 6:0:0:0: Attached scsi generic sg2 type 5
ISO 9660 Extensions: Microsoft Joliet Level 1
ISOFS: changing to secondary root
SELinux: initialized (dev sr2, type iso9660), uses genfs_contexts
and o/p after #modprobe usbserial vendor=0x12d1 product=0x1446
it runs successfully and then
# wvdialconf
Editing `/etc/wvdial.conf'.
Scanning your serial ports for a modem.
ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Modem Port Scan<*1>: S1 S2 S3
Sorry, no modem was detected! Is it in use by another program?
Did you configure it properly with setserial?
Please read the FAQ at http:// open.nit. ca/wiki/ ?WvDial
If you still have problems, send mail to <email address hidden>.