I can't get more than 1024x768 with xforcevesa and i915.modeset=0 on a Lenovo U160. If I boot into single mode, then do a rmmod i915; modprobe i915 modeset=1, the screen goes black while the LED backlight is still lit. The happens with all kernels, I tried, e.g. Ubuntu 10.4, 10.10, latest Fedora, and vanilla 2.6.36-RC1.
The graphics chip is a
00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller])
Subsystem: Lenovo Device 3920
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 43
Region 0: Memory at f0000000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 1800 [size=8]
Expansion ROM at <unassigned> [disabled] Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee0f00c Data: 4171 Capabilities: [d0] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [a4] PCI Advanced Features AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP-
Kernel modules: i915
I have attached the vbios dump *before* the modules insertion. The dmesg and the intel_reg_dump output were recorded *after* inserting i915.
Created an attachment (id=37954)
dmesg
Hello,
I can't get more than 1024x768 with xforcevesa and i915.modeset=0 on a Lenovo U160. If I boot into single mode, then do a rmmod i915; modprobe i915 modeset=1, the screen goes black while the LED backlight is still lit. The happens with all kernels, I tried, e.g. Ubuntu 10.4, 10.10, latest Fedora, and vanilla 2.6.36-RC1.
The graphics chip is a
Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4171
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0- ,D1-,D2- ,D3hot- ,D3cold- )
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a4] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller])
Subsystem: Lenovo Device 3920
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 43
Region 0: Memory at f0000000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 1800 [size=8]
Expansion ROM at <unassigned> [disabled]
Kernel modules: i915
I have attached the vbios dump *before* the modules insertion. The dmesg and the intel_reg_dump output were recorded *after* inserting i915.
Is there anything I can test?
Best regards,
Christian