----
00:1f.1 IDE interface [0101]: Intel Corporation 631xESB/632xESB IDE Controller [8086:269e] (rev 09) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Intel Corporation Unknown device [8086:7270]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at 30e8 [size=8]
Region 1: I/O ports at 30fc [size=4]
Region 2: I/O ports at 30e0 [size=8]
Region 3: I/O ports at 30f8 [size=4]
Region 4: I/O ports at 30c0 [size=16]
00:1f.2 IDE interface [0101]: Intel Corporation 631xESB/632xESB/3100 Chipset SATA Storage Controller IDE [8086:2680] (rev 09) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Intel Corporation Unknown device [8086:7270]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 0: I/O ports at 30d8 [size=8]
Region 1: I/O ports at 30f4 [size=4]
Region 2: I/O ports at 30d0 [size=8]
Region 3: I/O ports at 30f0 [size=4]
Region 4: I/O ports at 3020 [size=16]
Region 5: Memory at 52f04400 (32-bit, non-prefetchable) [size=1K] Capabilities: [70] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
---
This time with "sudo" so the Capabilities are shown instead of "Permission denied" ;-)
So yeah, 2680 is still missing on the ahci device list. Not sure why because IIRC that is also in the spec for esb2.
----
00:1f.1 IDE interface [0101]: Intel Corporation 631xESB/632xESB IDE Controller [8086:269e] (rev 09) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Intel Corporation Unknown device [8086:7270]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at 30e8 [size=8]
Region 1: I/O ports at 30fc [size=4]
Region 2: I/O ports at 30e0 [size=8]
Region 3: I/O ports at 30f8 [size=4]
Region 4: I/O ports at 30c0 [size=16]
00:1f.2 IDE interface [0101]: Intel Corporation 631xESB/ 632xESB/ 3100 Chipset SATA Storage Controller IDE [8086:2680] (rev 09) (prog-if 8f [Master SecP SecO PriP PriO])
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0- ,D1-,D2- ,D3hot+ ,D3cold- )
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Subsystem: Intel Corporation Unknown device [8086:7270]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 0: I/O ports at 30d8 [size=8]
Region 1: I/O ports at 30f4 [size=4]
Region 2: I/O ports at 30d0 [size=8]
Region 3: I/O ports at 30f0 [size=4]
Region 4: I/O ports at 3020 [size=16]
Region 5: Memory at 52f04400 (32-bit, non-prefetchable) [size=1K]
---
This time with "sudo" so the Capabilities are shown instead of "Permission denied" ;-)
So yeah, 2680 is still missing on the ahci device list. Not sure why because IIRC that is also in the spec for esb2.