I think it's the hard drive because it doesn't do anything after the "echo mem > /sys/power/state"... I took a look at:
http://bugzilla.kernel.org/show_bug.cgi?id=2039
Attached the HD information.
Regards,
Pedro
-- Pedro Martínez Juliá \ <email address hidden> )| WebLog: http://www.pedromj.com/blog / Página web: http://www.pedromj.com GoogleTalk: <email address hidden> Socio HispaLinux #311 Usuario Linux #275438 - http://counter.li.org
/dev/hda:
ATA device, with non-removable media Model Number: TOSHIBA MK8025GAS Serial Number: 658Q8001S Firmware Revision: KA023H Standards: Supported: 6 5 4 3 Likely used: 6 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 156301488 device size with M = 1024*1024: 76319 MBytes device size with M = 1000*1000: 80026 MBytes (80 GB) Capabilities: LBA, IORDY(can be disabled) bytes avail on r/w long: 48 Queue depth: 1 Standby timer values: spec'd by Standard, no device specific minimum R/W multiple sector transfer: Max = 16 Current = ? Advanced power management level: unknown setting (0x0080) DMA: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * NOP cmd * READ BUFFER cmd * WRITE BUFFER cmd * Host Protected Area feature set * Look-ahead * Write cache * Power Management feature set Security Mode feature set * SMART feature set * Mandatory FLUSH CACHE command * Device Configuration Overlay feature set SET MAX security extension * Advanced Power Management feature set * SMART self-test * SMART error logging Security: Master password revision code = 65534 supported not enabled not locked frozen not expired: security count not supported: enhanced erase 72min for SECURITY ERASE UNIT. HW reset results: CBLID- above Vih Device num = 0 determined by the jumper Checksum: correct
I think it's the hard drive because it doesn't do anything after the state". .. I took a look at:
"echo mem > /sys/power/
http:// bugzilla. kernel. org/show_ bug.cgi? id=2039
Attached the HD information.
Regards,
Pedro
-- www.pedromj. com/blog www.pedromj. com counter. li.org
Pedro Martínez Juliá
\ <email address hidden>
)| WebLog: http://
/ Página web: http://
GoogleTalk: <email address hidden>
Socio HispaLinux #311
Usuario Linux #275438 - http://
/dev/hda:
ATA device, with non-removable media
Model Number: TOSHIBA MK8025GAS
Serial Number: 658Q8001S
Firmware Revision: KA023H
Standards:
Supported: 6 5 4 3
Likely used: 6
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 156301488
device size with M = 1024*1024: 76319 MBytes
device size with M = 1000*1000: 80026 MBytes (80 GB)
Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 48 Queue depth: 1
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = ?
Advanced power management level: unknown setting (0x0080)
DMA: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* NOP cmd
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
* SMART feature set
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
SET MAX security extension
* Advanced Power Management feature set
* SMART self-test
* SMART error logging
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
72min for SECURITY ERASE UNIT.
HW reset results:
CBLID- above Vih
Device num = 0 determined by the jumper
Checksum: correct