Hello, i had the same Problem with a Marvell ethernet controller.
Bevore reading this bug-thread i made a upgrade from edgy to feisty but the problem still occurs every few hours.
I installed the driver from http://www.marvell.com/drivers/driverDisplay.do?dId=153&pId=36 as by Andreas Simon described.
The system uptime is now about 4 days. No error occurs since installation of the driver.
I think this is the solution for marvell-controller until the sky2 bug is fixed.
Hello, i had the same Problem with a Marvell ethernet controller. www.marvell. com/drivers/ driverDisplay. do?dId= 153&pId= 36 as by Andreas Simon described.
Bevore reading this bug-thread i made a upgrade from edgy to feisty but the problem still occurs every few hours.
I installed the driver from http://
The system uptime is now about 4 days. No error occurs since installation of the driver.
I think this is the solution for marvell-controller until the sky2 bug is fixed.
Controller-Info:
03:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controller (rev 22)
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+ ,D1+,D2+ ,D3hot+ ,D3cold+ )
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [5c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 2048 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0
Link: Latency L0s <256ns, L1 unlimited
Link: ASPM Disabled RCB 128 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Subsystem: Giga-byte Technology Marvell 88E8053 Gigabit Ethernet Controller (Gigabyte)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR+ <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f8000000 (64-bit, non-prefetchable) [size=16K]
Region 2: I/O ports at 9000 [size=256]
[virtual] Expansion ROM at f9300000 [disabled] [size=128K]
root@...:~# ethtool eth0
100baseT/ Half 100baseT/Full
1000baseT/ Half 1000baseT/Full
100baseT/ Half 100baseT/Full
1000baseT/ Half 1000baseT/Full
Transceiver: internal
Auto-negotiati on: on
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
Advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 0
Supports Wake-on: g
Wake-on: g
Link detected: yes