There is one more dependency you may have to install
Run command 'sudo apt-get install libsane-dev'
Next, re run ./configure --prefix=/usr
-------- Original message --------
From: peter mason <email address hidden>
Date: 08/03/2015 9:21 PM (GMT+05:30)
To: <email address hidden>
Subject: [Bug 1426110] Re: HPlip-3.15.2 make error
In the mean time a new upgrade has become available. 357MB. This uses up
more of my limited mobile byte allocation. Also when this works we need
to wait until the wifi adapter arrives before we can actually talk to
the printer.
./configure --prefix=/usr ...............Done
checking python2.7/Python.h usability... yes
checking python2.7/Python.h presence... yes
checking for python2.7/Python.h... yes
checking for sane_open in -lsane... no
configure: error: cannot find sane-backends-devel support (or --disable-scan-build)
pi@raspberrypi ~/Desktop/hplip-3.15.2 $
Have I gone backwards? Do I need to repeat the steps again?
peter
--
You received this bug notification because you are a member of HP Linux
Imaging and Printing, which is subscribed to HPLIP.
Matching subscriptions: HP Linux Imaging and Printing, HP Linux Imaging and Printing, HP Linux Imaging and Printing, HPLIP https://bugs.launchpad.net/bugs/1426110
Title:
HPlip-3.15.2 make error
Status in HP Linux Imaging and Printing:
New
Bug description:
I did a manual install of the hplip-3.15.2.tar on a raspberryPi 2, but
running make produces the following:
pi@raspberrypi ~/Desktop/source/hplip-3.15.2.tar/hplip-3.15.2 $ make
make: *** No targets specified and no makefile found. Stop.
pi@raspberrypi ~/Desktop/source/hplip-3.15.2.tar/hplip-3.15.2 $
I also tried hplip-3.15.2.run but that failed to find PY3.
There is one more dependency you may have to install
Run command 'sudo apt-get install libsane-dev'
Next, re run ./configure --prefix=/usr
-------- Original message --------
From: peter mason <email address hidden>
Date: 08/03/2015 9:21 PM (GMT+05:30)
To: <email address hidden>
Subject: [Bug 1426110] Re: HPlip-3.15.2 make error
In the mean time a new upgrade has become available. 357MB. This uses up
more of my limited mobile byte allocation. Also when this works we need
to wait until the wifi adapter arrives before we can actually talk to
the printer.
./configure --prefix=/usr ...............Done
checking python2.7/Python.h usability... yes 7/Python. h... yes scan-build) hplip-3. 15.2 $
checking python2.7/Python.h presence... yes
checking for python2.
checking for sane_open in -lsane... no
configure: error: cannot find sane-backends-devel support (or --disable-
pi@raspberrypi ~/Desktop/
Have I gone backwards? Do I need to repeat the steps again?
peter
-- /bugs.launchpad .net/bugs/ 1426110
You received this bug notification because you are a member of HP Linux
Imaging and Printing, which is subscribed to HPLIP.
Matching subscriptions: HP Linux Imaging and Printing, HP Linux Imaging and Printing, HP Linux Imaging and Printing, HPLIP
https:/
Title:
HPlip-3.15.2 make error
Status in HP Linux Imaging and Printing:
New
Bug description:
I did a manual install of the hplip-3.15.2.tar on a raspberryPi 2, but
running make produces the following:
pi@raspberrypi ~/Desktop/ source/ hplip-3. 15.2.tar/ hplip-3. 15.2 $ make source/ hplip-3. 15.2.tar/ hplip-3. 15.2 $
make: *** No targets specified and no makefile found. Stop.
pi@raspberrypi ~/Desktop/
I also tried hplip-3.15.2.run but that failed to find PY3.
Is it possible to install this software on RPi2?
To manage notifications about this bug go to: /bugs.launchpad .net/hplip/ +bug/1426110/ +subscriptions
https:/