Maxlinear Ethernet GPY115B report gpy_config_aneg failed: -110 and Link UP is not visible

[Ionut Nechita]

Hello Ubuntu Team,

I notice issue today with Maxlinear Ethernet GPY115B controller.
This controller report issue in dmesg and port not have link up.
My target is: OnLogic HX310 with two Ethernet Ports.
> Official page: https://www.onlogic.com/computers/industrial/fanless/helix-300/

Error: Maxlinear Ethernet GPY115B stmmac-3:01: gpy_config_aneg failed: -110

https://billauer.co.il/blog/2014/01/networkmanager-carrier-detect/
(stmmaceth: NetworkManager fails to bring up a wired Ethernet NIC)

OS: Ubuntu 24.04 LTS
Kernel: 6.8.0-22.22-generic 6.8.1

[Ionut Nechita (ionut-n2001)]

Hi,

I integrated locally this patches:

# tsn
0001-taprio-Add-support-for-frame-preemption-offload.tsn
0002-mqprio-Add-support-for-frame-preemption-offload.tsn
0003-taprio-Replace-tc_map_to_queue_mask.tsn
0004-core-Introduce-netdev_tc_map_to_queue_mask.tsn
0005-net-pcs-xpcs-enable-xpcs-reset-skipping.tsn
0006-net-stmmac-Bugfix-on-stmmac_interrupt-for-WOL.tsn
0007-net-stmmac-add-FPE-preempt-setting-for-TxQ-preemptible.tsn
0008-net-stmmac-support-recalculating-of-CBS-idle-slope-und.tsn
0009-net-stmmac-Add-module-param-to-del-keep-est-hw-conf.tsn
0010-net-phy-increase-gpy-loopback-test-delay.tsn
0011-net-stmmac-Resolve-poor-line-rate-after-switching-from.tsn
0012-net-phy-dp83867-perform-restart-AN-after-modifying-AN-.tsn
0013-stmmac-intel-Separate-ADL-N-and-RPL-P-device-ID-from-T.tsn
0014-net-stmmac-Adjust-mac_capabilities-for-Intel-mGbE-2.5G.tsn
0015-stmmac-intel-skip-xpcs-reset-for-2.5Gbps-on-Intel-Alde.tsn
0016-net-stmmac-add-check-for-2.5G-mode-to-prevent-MAC-capa.tsn
0017-stmmac-intel-Enable-PHY-WoL-in-ADL-N.tsn
0018-net-phy-reconfigure-PHY-WoL-when-WoL-option-is-enabled.tsn
0019-net-stmmac-fix-MAC-and-phylink-mismatch-issue-after-re.tsn
0020-xsk-add-txtime-field-in-xdp_desc-struct.tsn
0021-net-stmmac-restructure-Rx-Tx-hardware-timestamping-fun.tsn
0022-net-stmmac-Add-per-packet-time-based-scheduling-for-XD.tsn
0023-net-stmmac-introduce-AF_XDP-ZC-RX-HW-timestamps.tsn
0024-net-stmmac-add-fsleep-in-HW-Rx-timestamp-checking-loop.tsn
0025-net-stmmac-provide-allow_switch_interface-flag.tsn
0026-net-stmmac-select-PCS-negotiation-mode-according-to-th.tsn
0027-net-pcs-xpcs-re-initiate-clause-37-Auto-negotiation.tsn
0028-arch-x86-Add-IPC-mailbox-accessor-function-and-add-SoC.tsn
0029-net-stmmac-configure-SerDes-according-to-the-interface.tsn
0030-stmmac-intel-interface-switching-support-for-intel-pla.tsn
0031-net-stmmac-Set-mac_managed_pm-flag-from-stmmac-to-reso.tsn
0032-net-phylink-Add-module_exit.tsn

And now 1Gbps is working.

Link for series file (multiple patches):
https://github.com/intel/linux-intel-quilt/blob/mainline-tracking/linux/v6.9-rc3/patches/series

Port is available now and ip address exist on first interface.