Exclude DRM drivers from linux-modules
Bug #2037936 reported by
Juerg Haefliger
This bug affects 1 person
Affects | Status | Importance | Assigned to | Milestone | |
---|---|---|---|---|---|
linux-raspi (Ubuntu) |
Fix Released
|
Undecided
|
Unassigned | ||
Jammy |
Fix Released
|
Undecided
|
Unassigned | ||
Lunar |
Fix Released
|
Undecided
|
Unassigned | ||
Mantic |
Fix Released
|
Undecided
|
Unassigned |
Bug Description
[Impact]
DRM modules and their firmwares end up in the initrd and blow up its size. Most of them, especially nouveau and radeon, are unlikely to be used on a Pi, so move the modules to linux-modules-
[Fix]
Moeve DRM modules to linux-modules-
[Test Case]
Install new kernel and inspect initrd. Verify display still comes up.
[Regression Potential]
Blank display if a module is moved that is used for the primary display.
summary: |
- Exclude DRM modules from linux-modules + Exclude DRM drivers from linux-modules |
Changed in linux-raspi (Ubuntu Mantic): | |
status: | New → Fix Committed |
description: | updated |
Changed in linux-raspi (Ubuntu Lunar): | |
status: | New → Fix Committed |
Changed in linux-raspi (Ubuntu Jammy): | |
status: | New → Fix Committed |
To post a comment you must log in.
This bug was fixed in the package linux-raspi - 6.5.0-1004.6
---------------
linux-raspi (6.5.0-1004.6) mantic; urgency=medium
* mantic/linux-raspi: 6.5.0-1004.6 -proposed tracker (LP: #2037558)
* Include USB drivers in linux-modules (LP: #2037938)
- [Packaging] raspi: Include most USB modules in linux-modules
* Exclude DRM drivers from linux-modules (LP: #2037936)
- [Packaging] raspi: Exclude unlikely DRM modules from linux-modules
* Miscellaneous Ubuntu changes
- SAUCE: ARM: dts: Fix broken symlinks
- [Config] raspi: updateconfigs after update to raspberrypi rpi-6.1.y
(2023-09-29)
- [Config] raspi: Modify some RP1 configs to fix build failures
- [Config] raspi: Set ARCH_BRCMSTB=y
- [Config] raspi: Set IOMMU_SUPPORT=y and BCM2712_IOMMU=y
* Miscellaneous upstream changes denominator mixup" rescal: Support shared use raspberrypi- touchscreen: Insert more delays.
- Revert "ASoC: cs43130: Fix numerator/
- overlays: Add a sample hat_map
- Revert "usb: phy: generic: Get the vbus supply"
- config: 2712: Update defconfig
- dts: 2712: Update for device tree
- bcm2708_fb: Hack out dma support
- gpio_brcmstb: Allow to build for ARCH_BCM2835
- Allow RESET_BRCMSTB on ARCH_BCM2835
- pinctrl: bcm2712 pinctrl/pinconf driver
- vc4/fkms: Remove use of SMI peripheral
- mmc: brcmstb: add support for BCM2712
- sdhci: Add SD Express hook
- Add new "pispbe" driver (though not yet the Makesfiles or DT required to use
it)
- irqchip: irq-bcm2712-mip: Support for 2712's MIP
- reset: reset-brcmstb-
- net: macb: Also set DMA coherent mask
- usb: dwc3: Set DMA and coherent masks early
- drm/panel/
- PCI: brcmstb: Add BCM2712 support
- V4L2: Add PiSP opaque formats to V4L2
- V4L2: Add PiSP compressed formats to V4L2
- bcm2708_fb: Fix more build warnings
- dt-binding: mfd: Add binding for Raspberry Pi RP1
- mfd: Add rp1 driver
- dt-bindings: clock: Add bindings for Raspberry Pi RP1
- clk: Add rp1 clock driver
- dt-bindings: pinctrl: Add bindings for Raspberry Pi RP1
- pinctrl: Add rp1 driver
- serial: pl011: rp1 uart support
- mmc: sdhci-of-dwcmshc: define sdio timeout clocks
- mmc: sdhci-of-dwcmshc: rp1 sdio changes
- clk: rp1: Add sdio-clk driver
- i2c: designware: Add SMBUS quick command support
- dmaengine: dw-axi-dmac: Fixes for RP1
- spi: dw: Handle combined tx and rx messages
- pwm: Add support for RP1 PWM
- drm: Add RP1 DSI driver
- drm: Add RP1 DPI driver
- drm: Add RP1 VEC driver
- v4l2: Add pisp compression format support to v4l2
- media: rp1: Add CFE (Camera Front End) support
- dt-bindings: net: cdns,macb: AXI tuning properties
- ASoC: dwc: Support set_bclk_ratio
- ASoC: dwc: Add DMACR handling
- ASOC: dwc: Improve DMA shutdown
- ASOC: dwc: Fix 16-bit audio handling
- ASoC: bcm: Remove dependency on BCM2835 I2S
- hwmon: Add RP1 ADC and temperature driver
- mfd: bcm2835-pm: Add support for BCM2712
- soc: bcm: bcm2835-power: Add support for BCM2712
- drivers: spi: Fix spi-gpio to correctly implement sck-idle-in...