[   19.028737] cfg80211: Found new beacon on frequency: 2472 MHz (Ch 13) on phy0
[   19.320569] init: plymouth-stop pre-start process (1538) terminated with status 1
[   19.936132] wlan0: authenticate with e8:40:f2:3f:56:c0
[   19.952198] wlan0: send auth to e8:40:f2:3f:56:c0 (try 1/3)
[   19.954417] wlan0: authenticated
[   19.958513] wlan0: associate with e8:40:f2:3f:56:c0 (try 1/3)
[   19.962104] wlan0: RX AssocResp from e8:40:f2:3f:56:c0 (capab=0x431 status=0 aid=4)
[   19.962200] wlan0: associated
[   19.962517] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[19306.393676] wlan0: deauthenticating from e8:40:f2:3f:56:c0 by local choice (reason=3)
[19306.420811] cfg80211: All devices are disconnected, going to restore regulatory settings
[19306.420823] cfg80211: Restoring regulatory settings
[19306.420858] cfg80211: Calling CRDA to update world regulatory domain
[19306.454575] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain
[19306.457835] cfg80211: World regulatory domain updated:
[19306.457842] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[19306.457846] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[19306.457849] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[19306.457853] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[19306.457863] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[19306.457866] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[19307.954669] PM: Syncing filesystems ... done.
[19307.988372] PM: Preparing system for mem sleep
[19308.652756] Freezing user space processes ... (elapsed 0.01 seconds) done.
[19308.668144] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[19308.684086] PM: Entering mem sleep
[19308.684453] Suspending console(s) (use no_console_suspend to debug)
[19308.685186] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[19308.686393] sd 0:0:0:0: [sda] Stopping disk
[19310.270510] PM: suspend of devices complete after 1587.270 msecs
[19310.270514] PM: suspend devices took 1.588 seconds
[19310.270759] PM: late suspend of devices complete after 0.242 msecs
[19310.302643] ehci_hcd 0000:00:13.2: wake-up capability enabled by ACPI
[19310.318370] ohci_hcd 0000:00:13.0: wake-up capability enabled by ACPI
[19310.318417] ehci_hcd 0000:00:12.2: wake-up capability enabled by ACPI
[19310.334355] ohci_hcd 0000:00:12.0: wake-up capability enabled by ACPI
[19310.334433] PM: noirq suspend of devices complete after 63.727 msecs
[19310.334467] ACPI: Preparing to enter system sleep state S3
[19310.408071] PM: Saving platform NVS memory
[19310.438010] Disabling non-boot CPUs ...
[19310.438403] Broke affinity for irq 17
[19310.438411] Broke affinity for irq 19
[19310.542078] smpboot: CPU 1 is now offline
[19310.543080] ACPI: Low-level resume complete
[19310.543133] PM: Restoring platform NVS memory
[19310.546406] Enabling non-boot CPUs ...
[19310.546542] smpboot: Booting Node 0 Processor 1 APIC 0x1
[19310.557518] LVT offset 0 assigned for vector 0x400
[19310.560064] CPU1 is up
[19310.562482] ACPI: Waking up from system sleep state S3
[19310.733658] ohci_hcd 0000:00:12.0: wake-up capability disabled by ACPI
[19310.749475] ehci_hcd 0000:00:12.2: wake-up capability disabled by ACPI
[19310.749520] ohci_hcd 0000:00:13.0: wake-up capability disabled by ACPI
[19310.765459] ehci_hcd 0000:00:13.2: wake-up capability disabled by ACPI
[19310.813548] PM: noirq resume of devices complete after 110.048 msecs
[19310.813733] PM: early resume of devices complete after 0.146 msecs
[19310.813946] snd_hda_intel 0000:00:01.1: irq 43 for MSI/MSI-X
[19310.815577] ath: phy0: ASPM enabled: 0x42
[19310.828822] [drm] PCIE GART of 512M enabled (table at 0x0000000000040000).
[19310.829032] radeon 0000:00:01.0: WB enabled
[19310.829037] radeon 0000:00:01.0: fence driver on ring 0 use gpu addr 0x0000000018000c00 and cpu addr 0xffff88003673ec00
[19310.845379] [drm] ring test on 0 succeeded in 1 usecs
[19310.845419] [drm] ib test on ring 0 succeeded in 0 usecs
[19311.081149] usb 2-5: reset high-speed USB device number 3 using ehci_hcd
[19311.304755] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[19311.305455] ata1.00: failed to get Identify Device Data, Emask 0x1
[19311.306228] ata1.00: failed to get Identify Device Data, Emask 0x1
[19311.306239] ata1.00: configured for UDMA/100
[19311.321033] sd 0:0:0:0: [sda] Starting disk
[19311.476236] dpm_run_callback(): pnp_bus_resume+0x0/0x80 returns -19
[19311.476240] PM: Device 00:0a failed to resume: error -19
[19312.340221] PM: resume of devices complete after 1527.912 msecs
[19312.340517] PM: resume devices took 1.528 seconds
[19312.340704] PM: Finishing wakeup.
[19312.340707] Restarting tasks ... done.
[19312.413271] video LNXVIDEO:00: Restoring backlight state
[19312.439113] video LNXVIDEO:01: Restoring backlight state
[19313.289022] atl1c 0000:01:00.0: irq 44 for MSI/MSI-X
[19313.346881] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[19313.426423] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[19314.267295] cfg80211: Found new beacon on frequency: 2472 MHz (Ch 13) on phy0
[19315.274748] wlan0: authenticate with e8:40:f2:3f:56:c0
[19315.308108] wlan0: send auth to e8:40:f2:3f:56:c0 (try 1/3)
[19315.310226] wlan0: authenticated
[19315.316915] wlan0: associate with e8:40:f2:3f:56:c0 (try 1/3)
[19315.323059] wlan0: RX AssocResp from e8:40:f2:3f:56:c0 (capab=0x431 status=0 aid=4)
[19315.323156] wlan0: associated
[19315.325239] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[26981.954678] usb 1-3: new high-speed USB device number 3 using ehci_hcd
[26982.089356] usb 1-3: New USB device found, idVendor=0fce, idProduct=3137
[26982.089371] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[26982.089380] usb 1-3: Product: SEMC HSUSB Device
[26982.089387] usb 1-3: Manufacturer: SEMC
[26982.089394] usb 1-3: SerialNumber: 43423531314D3246394C
[26982.092281] scsi2 : usb-storage 1-3:1.0
[26983.092341] scsi 2:0:0:0: Direct-Access     SEMC     Mass Storage     0001 PQ: 0 ANSI: 2
[26983.094467] scsi 2:0:0:1: CD-ROM            SEMC     CD-ROM           0001 PQ: 0 ANSI: 2
[26983.098630] sd 2:0:0:0: Attached scsi generic sg3 type 0
[26983.110507] sd 2:0:0:0: [sdd] Attached SCSI removable disk
[26983.112470] sr0: scsi3-mmc drive: 0x/0x caddy
[26983.112485] cdrom: Uniform CD-ROM driver Revision: 3.20
[26983.112926] sr 2:0:0:1: Attached scsi CD-ROM sr0
[26983.113254] sr 2:0:0:1: Attached scsi generic sg4 type 5
[26995.240191] usb 1-3: USB disconnect, device number 3
[26995.250160] cdrom: issuing MRW background format suspend
[26995.489967] usb 1-3: new high-speed USB device number 4 using ehci_hcd
[26995.570020] hub 1-0:1.0: unable to enumerate USB device on port 3
[26995.985550] usb 3-3: new full-speed USB device number 3 using ohci_hcd
[26996.144116] usb 3-3: not running at top speed; connect to a high speed hub
[26996.156119] usb 3-3: New USB device found, idVendor=0fce, idProduct=3137
[26996.156135] usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[26996.156143] usb 3-3: Product: SEMC HSUSB Device
[26996.156150] usb 3-3: Manufacturer: SEMC
[26996.156157] usb 3-3: SerialNumber: 43423531314D3246394C
[26996.158563] scsi3 : usb-storage 3-3:1.0
[26996.291789] usb 3-3: USB disconnect, device number 3
[27000.637012] usb 1-3: new high-speed USB device number 5 using ehci_hcd
[27001.172656] usb 1-3: device not accepting address 5, error -71
[27001.228700] hub 1-0:1.0: unable to enumerate USB device on port 3
[27001.644234] usb 3-3: new full-speed USB device number 4 using ohci_hcd
[27001.802798] usb 3-3: not running at top speed; connect to a high speed hub
[27001.814797] usb 3-3: New USB device found, idVendor=0fce, idProduct=3137
[27001.814813] usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[27001.814821] usb 3-3: Product: SEMC HSUSB Device
[27001.814829] usb 3-3: Manufacturer: SEMC
[27001.814836] usb 3-3: SerialNumber: 43423531314D3246394C
[27001.817130] scsi4 : usb-storage 3-3:1.0
[27002.821998] scsi 4:0:0:0: Direct-Access     SEMC     Mass Storage     0001 PQ: 0 ANSI: 2
[27002.827830] scsi 4:0:0:1: CD-ROM            SEMC     CD-ROM           0001 PQ: 0 ANSI: 2
[27002.833820] sd 4:0:0:0: Attached scsi generic sg3 type 0
[27002.889882] sr0: scsi3-mmc drive: 0x/0x caddy
[27002.890407] sr 4:0:0:1: Attached scsi CD-ROM sr0
[27002.891256] sr 4:0:0:1: Attached scsi generic sg4 type 5
[27002.963831] sd 4:0:0:0: [sdd] Attached SCSI removable disk
[31005.219127] wlan0: deauthenticating from e8:40:f2:3f:56:c0 by local choice (reason=3)
[31005.242439] cfg80211: All devices are disconnected, going to restore regulatory settings
[31005.242452] cfg80211: Restoring regulatory settings
[31005.242460] cfg80211: Calling CRDA to update world regulatory domain
[31005.254423] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain
[31005.257701] cfg80211: World regulatory domain updated:
[31005.257704] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[31005.257713] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[31005.257719] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[31005.257722] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[31005.257725] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[31005.257728] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[31006.748880] PM: Syncing filesystems ... done.
[31006.777677] PM: Preparing system for mem sleep
[31007.841080] Freezing user space processes ... (elapsed 0.01 seconds) done.
[31007.857029] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[31007.872807] PM: Entering mem sleep
[31007.873175] Suspending console(s) (use no_console_suspend to debug)
[31007.873953] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[31007.875107] sd 0:0:0:0: [sda] Stopping disk
[31009.779166] PM: suspend of devices complete after 1907.489 msecs
[31009.779170] PM: suspend devices took 1.908 seconds
[31009.779426] PM: late suspend of devices complete after 0.254 msecs
[31009.811239] ehci_hcd 0000:00:13.2: wake-up capability enabled by ACPI
[31009.827000] ohci_hcd 0000:00:13.0: wake-up capability enabled by ACPI
[31009.827047] ehci_hcd 0000:00:12.2: wake-up capability enabled by ACPI
[31009.842985] ohci_hcd 0000:00:12.0: wake-up capability enabled by ACPI
[31009.843130] PM: noirq suspend of devices complete after 63.757 msecs
[31009.843165] ACPI: Preparing to enter system sleep state S3
[31009.917137] PM: Saving platform NVS memory
[31009.948319] Disabling non-boot CPUs ...
[31009.949193] Broke affinity for irq 17
[31009.949202] Broke affinity for irq 19
[31010.050732] smpboot: CPU 1 is now offline
[31010.051690] ACPI: Low-level resume complete
[31010.051743] PM: Restoring platform NVS memory
[31010.054983] Enabling non-boot CPUs ...
[31010.055120] smpboot: Booting Node 0 Processor 1 APIC 0x1
[31010.066095] LVT offset 0 assigned for vector 0x400
[31010.068646] CPU1 is up
[31010.071468] ACPI: Waking up from system sleep state S3
[31010.242257] ohci_hcd 0000:00:12.0: wake-up capability disabled by ACPI
[31010.258072] ehci_hcd 0000:00:12.2: wake-up capability disabled by ACPI
[31010.258117] ohci_hcd 0000:00:13.0: wake-up capability disabled by ACPI
[31010.274058] ehci_hcd 0000:00:13.2: wake-up capability disabled by ACPI
[31010.322155] PM: noirq resume of devices complete after 110.057 msecs
[31010.322349] PM: early resume of devices complete after 0.155 msecs
[31010.322755] snd_hda_intel 0000:00:01.1: irq 43 for MSI/MSI-X
[31010.324218] ath: phy0: ASPM enabled: 0x42
[31010.337208] [drm] PCIE GART of 512M enabled (table at 0x0000000000040000).
[31010.337379] radeon 0000:00:01.0: WB enabled
[31010.337384] radeon 0000:00:01.0: fence driver on ring 0 use gpu addr 0x0000000018000c00 and cpu addr 0xffff88003673ec00
[31010.353724] [drm] ring test on 0 succeeded in 1 usecs
[31010.353766] [drm] ib test on ring 0 succeeded in 0 usecs
[31010.589718] usb 2-5: reset high-speed USB device number 3 using ehci_hcd
[31010.813483] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[31010.813945] ata1.00: failed to get Identify Device Data, Emask 0x1
[31010.814504] ata1.00: failed to get Identify Device Data, Emask 0x1
[31010.814513] ata1.00: configured for UDMA/100
[31010.829537] sd 0:0:0:0: [sda] Starting disk
[31010.956887] dpm_run_callback(): pnp_bus_resume+0x0/0x80 returns -19
[31010.956890] PM: Device 00:0a failed to resume: error -19
[31011.848827] PM: resume of devices complete after 1527.901 msecs
[31011.849111] PM: resume devices took 1.528 seconds
[31011.849299] PM: Finishing wakeup.
[31011.849576] usb 3-3: USB disconnect, device number 4
[31011.849303] Restarting tasks ... done.
[31011.937150] video LNXVIDEO:00: Restoring backlight state
[31011.957740] video LNXVIDEO:01: Restoring backlight state
[31012.760810] atl1c 0000:01:00.0: irq 44 for MSI/MSI-X
[31012.776590] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[31012.891929] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[31014.747307] cfg80211: Found new beacon on frequency: 2472 MHz (Ch 13) on phy0
[31014.857320] wlan0: authenticate with e8:40:f2:3f:56:c0
[31014.888094] wlan0: send auth to e8:40:f2:3f:56:c0 (try 1/3)
[31014.890845] wlan0: authenticated
[31014.893604] wlan0: associate with e8:40:f2:3f:56:c0 (try 1/3)
[31014.900741] wlan0: RX AssocResp from e8:40:f2:3f:56:c0 (capab=0x431 status=0 aid=7)
[31014.900846] wlan0: associated
[31014.901489] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready