[    5.448383] ADDRCONF(NETDEV_UP): eth0: link is not ready
[    5.605064] Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd047b3/0xb40000/0xa0000
[    5.605075] serio: Synaptics pass-through port at isa0060/serio1/input0
[    5.651033] HDMI status: Pin=5 Presence_Detect=0 ELD_Valid=0
[    5.663201] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input7
[    5.682985] HDMI status: Pin=5 Presence_Detect=0 ELD_Valid=0
[    5.717365] HDMI status: Pin=5 Presence_Detect=0 ELD_Valid=0
[    5.746825] HDMI status: Pin=5 Presence_Detect=0 ELD_Valid=0
[    5.763024] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input8
[    5.763237] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input9
[    5.763381] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input10
[    5.763521] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input11
[    5.765026] nvidia 0000:01:00.0: power state changed by ACPI to D0
[    5.765040] nvidia 0000:01:00.0: power state changed by ACPI to D0
[    5.765063] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    5.765088] nvidia 0000:01:00.0: setting latency timer to 64
[    5.765100] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[    5.765377] NVRM: loading NVIDIA UNIX x86_64 Kernel Module  280.13  Wed Jul 27 16:53:56 PDT 2011
[    5.818163] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[    5.977993] ppdev: user-space parallel port driver
[    5.987050] audit_printk_skb: 45 callbacks suppressed
[    5.987053] type=1400 audit(1318090400.274:26): apparmor="STATUS" operation="profile_replace" name="/usr/lib/cups/backend/cups-pdf" pid=1631 comm="apparmor_parser"
[    5.987490] type=1400 audit(1318090400.274:27): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/cupsd" pid=1631 comm="apparmor_parser"
[    6.109679] vboxdrv: Found 4 processor cores.
[    6.110252] vboxdrv: fAsync=0 offMin=0x1eb offMax=0x1a6e
[    6.110311] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[    6.110313] vboxdrv: Successfully loaded version 4.1.2_Ubuntu (interface 0x00190000).
[    6.125451] vboxpci: IOMMU not found (not registered)
[    6.159304] Bluetooth: RFCOMM TTY layer initialized
[    6.159309] Bluetooth: RFCOMM socket layer initialized
[    6.159311] Bluetooth: RFCOMM ver 1.11
[    6.170952] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    6.170958] Bluetooth: BNEP filters: protocol multicast
[    6.322169] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[    6.325130] EXT4-fs (sda2): re-mounted. Opts: commit=0
[    7.053545] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx
[    7.053551] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[    7.054151] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    7.341286] cfg80211: Found new beacon on frequency: 2472 MHz (Ch 13) on phy0
[   12.973314] IBM TrackPoint firmware: 0x0e, buttons: 3/3
[   13.262754] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/serio2/input/input12
[   17.154239] eth0: no IPv6 routers present
[   23.283746] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[   23.295642] EXT4-fs (sda2): re-mounted. Opts: commit=0
[   71.969851] EXT4-fs (sdb4): mounted filesystem with ordered data mode. Opts: (null)
[  139.052042] usb 1-1.4: USB disconnect, device number 4
[  139.052108] btusb_intr_complete: hci0 urb ffff88022b6aacc0 failed to resubmit (19)
[  139.052146] btusb_bulk_complete: hci0 urb ffff88022b6aad80 failed to resubmit (19)
[  139.052151] btusb_bulk_complete: hci0 urb ffff88022b6aae40 failed to resubmit (19)
[  311.812139] e1000e: eth0 NIC Link is Down
[  366.473136] wlan0: authenticate with bc:05:43:7a:65:d5 (try 1)
[  366.475820] wlan0: authenticated
[  366.538525] wlan0: associate with bc:05:43:7a:65:d5 (try 1)
[  366.542199] wlan0: RX AssocResp from bc:05:43:7a:65:d5 (capab=0x431 status=0 aid=2)
[  366.542207] wlan0: associated
[  366.553460] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  374.634156] iwlagn 0000:03:00.0: iwlagn_tx_agg_start on ra = bc:05:43:7a:65:d5 tid = 0
[  377.020156] wlan0: no IPv6 routers present