00:00.0 Host bridge [0600]: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller [8086:2590] (rev 03)
	Subsystem: IBM Device [1014:0575]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>
	Kernel driver in use: agpgart-intel
	Kernel modules: intel-agp

00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller [8086:2592] (rev 03)
	Subsystem: IBM Device [1014:0582]
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at a0080000 (32-bit, non-prefetchable) [size=512K]
	Region 1: I/O ports at 1800 [size=8]
	Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M]
	Region 3: Memory at a0000000 (32-bit, non-prefetchable) [size=256K]
	Capabilities: <access denied>
	Kernel modules: intelfb

00:02.1 Display controller [0380]: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller [8086:2792] (rev 03)
	Subsystem: IBM Device [1014:0582]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Region 0: Memory at 68000000 (32-bit, non-prefetchable) [disabled] [size=512K]
	Capabilities: <access denied>

00:1c.0 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 [8086:2660] (rev 03)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	Memory behind bridge: a0100000-a01fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp

00:1d.0 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 [8086:2658] (rev 03)
	Subsystem: IBM Device [1014:0565]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 4: I/O ports at 1820 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:1d.1 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 [8086:2659] (rev 03)
	Subsystem: IBM Device [1014:0565]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 17
	Region 4: I/O ports at 1840 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:1d.2 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 [8086:265a] (rev 03)
	Subsystem: IBM Device [1014:0565]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin C routed to IRQ 18
	Region 4: I/O ports at 1860 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:1d.3 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 [8086:265b] (rev 03)
	Subsystem: IBM Device [1014:0565]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin D routed to IRQ 19
	Region 4: I/O ports at 1880 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:1d.7 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller [8086:265c] (rev 03) (prog-if 20)
	Subsystem: IBM Device [1014:0566]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin D routed to IRQ 19
	Region 0: Memory at a0040000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci_hcd
	Kernel modules: ehci-hcd

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev d3) (prog-if 01)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Bus: primary=00, secondary=04, subordinate=07, sec-latency=64
	I/O behind bridge: 00002000-00005fff
	Memory behind bridge: a0200000-afffffff
	Prefetchable memory behind bridge: 00000000d0000000-00000000d7ffffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>

00:1e.2 Multimedia audio controller [0401]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller [8086:266e] (rev 03)
	Subsystem: IBM Device [1014:0581]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 22
	Region 0: I/O ports at 1c00 [size=256]
	Region 1: I/O ports at 18c0 [size=64]
	Region 2: Memory at a0040800 (32-bit, non-prefetchable) [size=512]
	Region 3: Memory at a0040400 (32-bit, non-prefetchable) [size=256]
	Capabilities: <access denied>
	Kernel driver in use: Intel ICH
	Kernel modules: snd-intel8x0

00:1f.0 ISA bridge [0601]: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge [8086:2641] (rev 03)
	Subsystem: IBM Device [1014:0568]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Kernel modules: iTCO_wdt, intel-rng

00:1f.2 IDE interface [0101]: Intel Corporation 82801FBM (ICH6M) SATA Controller [8086:2653] (rev 03) (prog-if 80 [Master])
	Subsystem: IBM Device [1014:056a]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
	Latency: 0
	Region 0: I/O ports at 01f0 [size=8]
	Region 1: I/O ports at 03f4 [size=1]
	Region 2: I/O ports at 0170 [size=8]
	Region 3: I/O ports at 0374 [size=1]
	Region 4: I/O ports at 1810 [size=16]
	Capabilities: <access denied>
	Kernel driver in use: ata_piix
	Kernel modules: ahci, ata_piix

00:1f.3 SMBus [0c05]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller [8086:266a] (rev 03)
	Subsystem: IBM Device [1014:056b]
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin A routed to IRQ 11
	Region 4: I/O ports at 18a0 [size=32]
	Kernel modules: i2c-i801

02:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5751M Gigabit Ethernet PCI Express [14e4:167d] (rev 11)
	Subsystem: IBM Device [1014:0577]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at a0100000 (64-bit, non-prefetchable) [size=64K]
	Expansion ROM at <ignored> [disabled]
	Capabilities: <access denied>
	Kernel driver in use: tg3
	Kernel modules: tg3

04:00.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c476 II [1180:0476] (rev 8d)
	Subsystem: IBM Device [1014:0555]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 168
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at a0200000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=04, secondary=05, subordinate=06, sec-latency=176
	Memory window 0: d0000000-d3fff000 (prefetchable)
	Memory window 1: a4000000-a7fff000
	I/O window 0: 00002000-000020ff
	I/O window 1: 00002400-000024ff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
	16-bit legacy interface ports at 0001
	Kernel driver in use: yenta_cardbus
	Kernel modules: yenta_socket

04:00.1 SD Host controller [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter [1180:0822] (rev 13)
	Subsystem: IBM Device [1014:0556]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64
	Interrupt: pin B routed to IRQ 17
	Region 0: Memory at a0201000 (32-bit, non-prefetchable) [size=256]
	Capabilities: <access denied>
	Kernel driver in use: sdhci-pci
	Kernel modules: sdhci-pci

04:02.0 Network controller [0280]: Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection [8086:4220] (rev 05)
	Subsystem: Intel Corporation Device [8086:2712]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (750ns min, 6000ns max), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 21
	Region 0: Memory at a0202000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: <access denied>
	Kernel driver in use: ipw2200
	Kernel modules: ipw2200






-----
dmesg
-----

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.27-7-generic (buildd@palmer) (gcc version 4.3.2 (Ubuntu 4.3.2-1ubuntu11) ) #1 SMP Thu Oct 30 04:18:38 UTC 2008 (Ubuntu 2.6.27-7.15-generic)
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
[    0.000000]  BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000d0000 - 00000000000d4000 (reserved)
[    0.000000]  BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000005f6d0000 (usable)
[    0.000000]  BIOS-e820: 000000005f6d0000 - 000000005f6e5000 (ACPI data)
[    0.000000]  BIOS-e820: 000000005f6e5000 - 000000005f700000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000005f700000 - 0000000060000000 (reserved)
[    0.000000]  BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[    0.000000] last_pfn = 0x5f6d0 max_arch_pfn = 0x100000
[    0.000000] kernel direct mapping tables up to 38000000 @ 7000-c000
[    0.000000] RAMDISK: 37831000 - 37fef6d0
[    0.000000] DMI present.
[    0.000000] ACPI: RSDP 000F6C00, 0024 (r2 IBM   )
[    0.000000] ACPI: XSDT 5F6D4770, 005C (r1 IBM    TP-74        2060  LTP        0)
[    0.000000] ACPI: FACP 5F6D4800, 00F4 (r3 IBM    TP-74        2060 IBM         1)
[    0.000000] ACPI Warning (tbfadt-0442): Optional field "Gpe1Block" has zero address or length: 000000000000102C/0 [20080609]
[    0.000000] ACPI: DSDT 5F6D49E7, 1038A (r1 IBM    TP-74        2060 MSFT  100000E)
[    0.000000] ACPI: FACS 5F6F6000, 0040
[    0.000000] ACPI: SSDT 5F6D49B4, 0033 (r1 IBM    TP-74        2060 MSFT  100000E)
[    0.000000] ACPI: ECDT 5F6E4D71, 0052 (r1 IBM    TP-74        2060 IBM         1)
[    0.000000] ACPI: TCPA 5F6E4DC3, 0032 (r1 IBM    TP-74        2060 PTL         1)
[    0.000000] ACPI: APIC 5F6E4DF5, 005A (r1 IBM    TP-74        2060 IBM         1)
[    0.000000] ACPI: MCFG 5F6E4E4F, 003E (r1 IBM    TP-74        2060 IBM         1)
[    0.000000] ACPI: BOOT 5F6E4FD8, 0028 (r1 IBM    TP-74        2060  LTP        1)
[    0.000000] 630MB HIGHMEM available.
[    0.000000] 896MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 38000000
[    0.000000]   low ram: 00000000 - 38000000
[    0.000000]   bootmap 00008000 - 0000f000
[    0.000000] (9 early reservations) ==> bootmem [0000000000 - 0038000000]
[    0.000000]   #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
[    0.000000]   #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
[    0.000000]   #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
[    0.000000]   #3 [0000100000 - 00005c0a20]    TEXT DATA BSS ==> [0000100000 - 00005c0a20]
[    0.000000]   #4 [0037831000 - 0037fef6d0]          RAMDISK ==> [0037831000 - 0037fef6d0]
[    0.000000]   #5 [00005c1000 - 00005c4000]    INIT_PG_TABLE ==> [00005c1000 - 00005c4000]
[    0.000000]   #6 [000009f000 - 0000100000]    BIOS reserved ==> [000009f000 - 0000100000]
[    0.000000]   #7 [0000007000 - 0000008000]          PGTABLE ==> [0000007000 - 0000008000]
[    0.000000]   #8 [0000008000 - 000000f000]          BOOTMAP ==> [0000008000 - 000000f000]
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000000 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x00038000
[    0.000000]   HighMem  0x00038000 -> 0x0005f6d0
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[2] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x0005f6d0
[    0.000000] On node 0 totalpages: 390767
[    0.000000] free_area_init_node: node 0, pgdat c048a500, node_mem_map c1000000
[    0.000000]   DMA zone: 3963 pages, LIFO batch:0
[    0.000000]   Normal zone: 223300 pages, LIFO batch:31
[    0.000000]   HighMem zone: 160068 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[    0.000000] mapped APIC to ffffb000 (fee00000)
[    0.000000] mapped IOAPIC to ffffa000 (fec00000)
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d0000
[    0.000000] PM: Registered nosave memory: 00000000000d0000 - 00000000000d4000
[    0.000000] PM: Registered nosave memory: 00000000000d4000 - 00000000000dc000
[    0.000000] PM: Registered nosave memory: 00000000000dc000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at 68000000 (gap: 60000000:80000000)
[    0.000000] PERCPU: Allocating 41628 bytes of per cpu data
[    0.000000] NR_CPUS: 64, nr_cpu_ids: 1, nr_node_ids 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 387331
[    0.000000] Kernel command line: root=UUID=796ce08c-e145-4d20-a6ac-9578463c2b3a ro quiet splash 
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[    0.000000] Extended CMOS year: 2000
[    0.000000] TSC: PIT calibration confirmed by PMTIMER.
[    0.000000] TSC: using PIT calibration value
[    0.000000] Detected 1595.984 MHz processor.
[    0.004000] Console: colour VGA+ 80x25
[    0.004000] console [tty0] enabled
[    0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.004000] Memory: 1534712k/1563456k available (2572k kernel code, 27456k reserved, 1160k data, 424k init, 645952k highmem)
[    0.004000] virtual kernel memory layout:
[    0.004000]     fixmap  : 0xffc77000 - 0xfffff000   (3616 kB)
[    0.004000]     pkmap   : 0xff400000 - 0xff800000   (4096 kB)
[    0.004000]     vmalloc : 0xf8800000 - 0xff3fe000   ( 107 MB)
[    0.004000]     lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
[    0.004000]       .init : 0xc04ab000 - 0xc0515000   ( 424 kB)
[    0.004000]       .data : 0xc03832aa - 0xc04a5680   (1160 kB)
[    0.004000]       .text : 0xc0100000 - 0xc03832aa   (2572 kB)
[    0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[    0.004000] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.004021] Calibrating delay loop (skipped), value calculated using timer frequency.. 3191.96 BogoMIPS (lpj=6383936)
[    0.004052] Security Framework initialized
[    0.004069] SELinux:  Disabled at boot.
[    0.004100] AppArmor: AppArmor initialized
[    0.004115] Mount-cache hash table entries: 512
[    0.004355] Initializing cgroup subsys ns
[    0.004366] Initializing cgroup subsys cpuacct
[    0.004369] Initializing cgroup subsys memory
[    0.004393] CPU: L1 I cache: 32K, L1 D cache: 32K
[    0.004396] CPU: L2 cache: 2048K
[    0.004418] Checking 'hlt' instruction... OK.
[    0.020624] SMP alternatives: switching to UP code
[    0.027304] Freeing SMP alternatives: 11k freed
[    0.027307] ACPI: Core revision 20080609
[    0.035867] ACPI: Checking initramfs for custom DSDT
[    0.472288] ENABLING IO-APIC IRQs
[    0.472495] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.512938] CPU0: Intel(R) Pentium(R) M processor 1.60GHz stepping 08
[    0.516031] Brought up 1 CPUs
[    0.516031] Total of 1 processors activated (3191.96 BogoMIPS).
[    0.516031] CPU0 attaching sched-domain:
[    0.516031]  domain 0: span 0 level CPU
[    0.516031]   groups: 0
[    0.516031] net_namespace: 840 bytes
[    0.516031] Booting paravirtualized kernel on bare hardware
[    0.516031] Time: 18:36:27  Date: 11/03/08
[    0.516031] NET: Registered protocol family 16
[    0.516031] EISA bus registered
[    0.516031] ACPI: bus type pci registered
[    0.516031] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[    0.516031] PCI: MCFG area at e0000000 reserved in E820
[    0.516031] PCI: Using MMCONFIG for extended config space
[    0.516031] PCI: Using configuration type 1 for base access
[    0.516110] ACPI: EC: EC description table is found, configuring boot EC
[    0.531172] ACPI: EC: non-query interrupt received, switching to interrupt mode
[    0.673193] ACPI: Interpreter enabled
[    0.673197] ACPI: (supports S0 S3 S4 S5)
[    0.673216] ACPI: Using IOAPIC for interrupt routing
[    0.695192] ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
[    0.695196] ACPI: EC: driver started in interrupt mode
[    0.695266] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.695386] PCI: 0000:00:02.0 reg 10 32bit mmio: [a0080000, a00fffff]
[    0.695392] PCI: 0000:00:02.0 reg 14 io port: [1800, 1807]
[    0.695398] PCI: 0000:00:02.0 reg 18 32bit mmio: [c0000000, cfffffff]
[    0.695404] PCI: 0000:00:02.0 reg 1c 32bit mmio: [a0000000, a003ffff]
[    0.695438] PCI: 0000:00:02.1 reg 10 32bit mmio: [0, 7ffff]
[    0.695578] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.695584] pci 0000:00:1c.0: PME# disabled
[    0.695640] PCI: 0000:00:1d.0 reg 20 io port: [1820, 183f]
[    0.695703] PCI: 0000:00:1d.1 reg 20 io port: [1840, 185f]
[    0.695766] PCI: 0000:00:1d.2 reg 20 io port: [1860, 187f]
[    0.695828] PCI: 0000:00:1d.3 reg 20 io port: [1880, 189f]
[    0.695896] PCI: 0000:00:1d.7 reg 10 32bit mmio: [a0040000, a00403ff]
[    0.695953] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.695960] pci 0000:00:1d.7: PME# disabled
[    0.696056] PCI: 0000:00:1e.2 reg 10 io port: [1c00, 1cff]
[    0.696065] PCI: 0000:00:1e.2 reg 14 io port: [18c0, 18ff]
[    0.696073] PCI: 0000:00:1e.2 reg 18 32bit mmio: [a0040800, a00409ff]
[    0.696082] PCI: 0000:00:1e.2 reg 1c 32bit mmio: [a0040400, a00404ff]
[    0.696118] pci 0000:00:1e.2: PME# supported from D0 D3hot D3cold
[    0.696124] pci 0000:00:1e.2: PME# disabled
[    0.696216] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[    0.696224] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[    0.696230] pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
[    0.696266] PCI: 0000:00:1f.2 reg 10 io port: [0, 7]
[    0.696275] PCI: 0000:00:1f.2 reg 14 io port: [0, 3]
[    0.696283] PCI: 0000:00:1f.2 reg 18 io port: [0, 7]
[    0.696292] PCI: 0000:00:1f.2 reg 1c io port: [0, 3]
[    0.696300] PCI: 0000:00:1f.2 reg 20 io port: [1810, 181f]
[    0.696331] pci 0000:00:1f.2: PME# supported from D3hot
[    0.696337] pci 0000:00:1f.2: PME# disabled
[    0.696394] PCI: 0000:00:1f.3 reg 20 io port: [18a0, 18bf]
[    0.696505] PCI: 0000:02:00.0 reg 10 64bit mmio: [a0100000, a010ffff]
[    0.696574] pci 0000:02:00.0: PME# supported from D3hot D3cold
[    0.696581] pci 0000:02:00.0: PME# disabled
[    0.696635] PCI: bridge 0000:00:1c.0 32bit mmio: [a0100000, a01fffff]
[    0.696692] PCI: 0000:04:00.0 reg 10 32bit mmio: [a0200000, a0200fff]
[    0.696714] pci 0000:04:00.0: supports D1
[    0.696716] pci 0000:04:00.0: supports D2
[    0.696719] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.696726] pci 0000:04:00.0: PME# disabled
[    0.696771] PCI: 0000:04:00.1 reg 10 32bit mmio: [a0201000, a02010ff]
[    0.696839] pci 0000:04:00.1: supports D1
[    0.696841] pci 0000:04:00.1: supports D2
[    0.696843] pci 0000:04:00.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.696850] pci 0000:04:00.1: PME# disabled
[    0.696909] PCI: 0000:04:02.0 reg 10 32bit mmio: [a0202000, a0202fff]
[    0.696981] pci 0000:04:02.0: PME# supported from D0 D3hot D3cold
[    0.696987] pci 0000:04:02.0: PME# disabled
[    0.697046] pci 0000:00:1e.0: transparent bridge
[    0.697051] PCI: bridge 0000:00:1e.0 io port: [2000, 5fff]
[    0.697057] PCI: bridge 0000:00:1e.0 32bit mmio: [a0200000, afffffff]
[    0.697066] PCI: bridge 0000:00:1e.0 64bit mmio pref: [d0000000, d7ffffff]
[    0.697106] bus 00 -> node 0
[    0.697116] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.697437] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP0._PRT]
[    0.697662] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
[    0.701543] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
[    0.701880] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
[    0.702218] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
[    0.702554] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
[    0.702888] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11)
[    0.703221] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11)
[    0.703555] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11)
[    0.703890] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11)
[    0.704168] ACPI: Power Resource [PUBS] (on)
[    0.704314] Linux Plug and Play Support v0.97 (c) Adam Belay
[    0.704355] pnp: PnP ACPI init
[    0.704363] ACPI: bus type pnp registered
[    0.713467] pnp: PnP ACPI: found 11 devices
[    0.713470] ACPI: ACPI bus type pnp unregistered
[    0.713473] PnPBIOS: Disabled by ACPI PNP
[    0.713874] PCI: Using ACPI for IRQ routing
[    0.714013] NET: Registered protocol family 8
[    0.714013] NET: Registered protocol family 20
[    0.714013] NetLabel: Initializing
[    0.714013] NetLabel:  domain hash size = 128
[    0.714013] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.714013] NetLabel:  unlabeled traffic allowed by default
[    0.714013] hpet clockevent registered
[    0.714013] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.714013] hpet0: 3 64-bit timers, 14318180 Hz
[    0.714013] tracer: 772 pages allocated for 65536 entries of 48 bytes
[    0.714013]    actual entries 65620
[    0.714013] AppArmor: AppArmor Filesystem Enabled
[    0.714013] ACPI: RTC can wake from S4
[    0.714013] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[    0.714013] system 00:00: iomem range 0xc0000-0xc3fff could not be reserved
[    0.714013] system 00:00: iomem range 0xc4000-0xc7fff could not be reserved
[    0.714013] system 00:00: iomem range 0xc8000-0xcbfff has been reserved
[    0.714013] system 00:00: iomem range 0xcc000-0xcffff could not be reserved
[    0.714013] system 00:00: iomem range 0xd0000-0xd3fff could not be reserved
[    0.714013] system 00:00: iomem range 0xdc000-0xdffff could not be reserved
[    0.714013] system 00:00: iomem range 0xe0000-0xe3fff could not be reserved
[    0.714013] system 00:00: iomem range 0xe4000-0xe7fff could not be reserved
[    0.714013] system 00:00: iomem range 0xe8000-0xebfff could not be reserved
[    0.714013] system 00:00: iomem range 0xec000-0xeffff could not be reserved
[    0.714013] system 00:00: iomem range 0xf0000-0xfffff could not be reserved
[    0.714013] system 00:00: iomem range 0x100000-0x5fffffff could not be reserved
[    0.714013] system 00:00: iomem range 0xfec00000-0xffffffff could not be reserved
[    0.714013] system 00:02: ioport range 0x1000-0x107f has been reserved
[    0.714013] system 00:02: ioport range 0x1180-0x11bf has been reserved
[    0.714013] system 00:02: ioport range 0x15e0-0x15ef has been reserved
[    0.714013] system 00:02: ioport range 0x1600-0x162f has been reserved
[    0.714013] system 00:02: ioport range 0x1632-0x167f has been reserved
[    0.714013] system 00:02: ioport range 0x15c0-0x15df has been reserved
[    0.714013] system 00:02: iomem range 0xe0000000-0xefffffff could not be reserved
[    0.714013] system 00:02: iomem range 0xf0008000-0xf000bfff could not be reserved
[    0.714013] system 00:02: iomem range 0xfed14000-0xfed17fff could not be reserved
[    0.714013] system 00:02: iomem range 0xfed18000-0xfed18fff could not be reserved
[    0.714013] system 00:02: iomem range 0xfed19000-0xfed19fff could not be reserved
[    0.751044] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[    0.751048] pci 0000:00:1c.0:   IO window: disabled
[    0.751055] pci 0000:00:1c.0:   MEM window: 0xa0100000-0xa01fffff
[    0.751061] pci 0000:00:1c.0:   PREFETCH window: disabled
[    0.751072] pci 0000:04:00.0: CardBus bridge, secondary bus 0000:05
[    0.751075] pci 0000:04:00.0:   IO window: 0x002000-0x0020ff
[    0.751082] pci 0000:04:00.0:   IO window: 0x002400-0x0024ff
[    0.751088] pci 0000:04:00.0:   PREFETCH window: 0xd0000000-0xd3ffffff
[    0.751095] pci 0000:04:00.0:   MEM window: 0xa4000000-0xa7ffffff
[    0.751102] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:04
[    0.751106] pci 0000:00:1e.0:   IO window: 0x2000-0x5fff
[    0.751113] pci 0000:00:1e.0:   MEM window: 0xa0200000-0xafffffff
[    0.751120] pci 0000:00:1e.0:   PREFETCH window: 0x000000d0000000-0x000000d7ffffff
[    0.751140] pci 0000:00:1c.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[    0.751147] pci 0000:00:1c.0: setting latency timer to 64
[    0.751156] pci 0000:00:1e.0: setting latency timer to 64
[    0.751169] pci 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.751177] bus: 00 index 0 io port: [0, ffff]
[    0.751180] bus: 00 index 1 mmio: [0, ffffffff]
[    0.751182] bus: 02 index 0 mmio: [0, 0]
[    0.751185] bus: 02 index 1 mmio: [a0100000, a01fffff]
[    0.751188] bus: 02 index 2 mmio: [0, 0]
[    0.751190] bus: 02 index 3 mmio: [0, 0]
[    0.751193] bus: 04 index 0 io port: [2000, 5fff]
[    0.751195] bus: 04 index 1 mmio: [a0200000, afffffff]
[    0.751198] bus: 04 index 2 mmio: [d0000000, d7ffffff]
[    0.751201] bus: 04 index 3 io port: [0, ffff]
[    0.751204] bus: 04 index 4 mmio: [0, ffffffff]
[    0.751206] bus: 05 index 0 io port: [2000, 20ff]
[    0.751209] bus: 05 index 1 io port: [2400, 24ff]
[    0.751212] bus: 05 index 2 mmio: [d0000000, d3ffffff]
[    0.751214] bus: 05 index 3 mmio: [a4000000, a7ffffff]
[    0.751226] NET: Registered protocol family 2
[    0.751373] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.751657] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.752528] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.753095] TCP: Hash tables configured (established 131072 bind 65536)
[    0.753099] TCP reno registered
[    0.753265] NET: Registered protocol family 1
[    0.753422] checking if image is initramfs... it is
[    1.216084] Switched to high resolution mode on CPU 0
[    1.611205] Freeing initrd memory: 7929k freed
[    1.611479] Simple Boot Flag at 0x35 set to 0x1
[    1.612145] audit: initializing netlink socket (disabled)
[    1.612169] type=2000 audit(1225737387.612:1): initialized
[    1.619955] highmem bounce pool size: 64 pages
[    1.619964] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    1.622861] VFS: Disk quotas dquot_6.5.1
[    1.622970] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.623121] msgmni has been set to 1753
[    1.623278] io scheduler noop registered
[    1.623282] io scheduler anticipatory registered
[    1.623285] io scheduler deadline registered
[    1.623300] io scheduler cfq registered (default)
[    1.623319] pci 0000:00:02.0: Boot video device
[    1.623551] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[    1.623601] pcieport-driver 0000:00:1c.0: found MSI capability
[    1.623653] pci_express 0000:00:1c.0:pcie00: allocate port service
[    1.623709] pci_express 0000:00:1c.0:pcie02: allocate port service
[    1.623761] pci_express 0000:00:1c.0:pcie03: allocate port service
[    1.624470] isapnp: Scanning for PnP cards...
[    1.978616] isapnp: No Plug & Play device found
[    2.020684] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[    2.023392] brd: module loaded
[    2.023487] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[    2.023637] PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
[    2.032825] serio: i8042 KBD port at 0x60,0x64 irq 1
[    2.032833] serio: i8042 AUX port at 0x60,0x64 irq 12
[    2.033201] mice: PS/2 mouse device common for all mice
[    2.033368] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[    2.033401] rtc0: alarms up to one month, y3k, hpet irqs
[    2.033543] EISA: Probing bus 0 at eisa.0
[    2.033551] Cannot allocate resource for EISA slot 1
[    2.033555] Cannot allocate resource for EISA slot 2
[    2.033558] Cannot allocate resource for EISA slot 3
[    2.033560] Cannot allocate resource for EISA slot 4
[    2.033563] Cannot allocate resource for EISA slot 5
[    2.033578] EISA: Detected 0 cards.
[    2.033583] cpuidle: using governor ladder
[    2.033586] cpuidle: using governor menu
[    2.034193] TCP cubic registered
[    2.034229] Using IPI No-Shortcut mode
[    2.034448] registered taskstats version 1
[    2.034588]   Magic number: 0:745:644
[    2.034788] rtc_cmos 00:06: setting system clock to 2008-11-03 18:36:28 UTC (1225737388)
[    2.034793] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    2.034795] EDD information not available.
[    2.035115] Freeing unused kernel memory: 424k freed
[    2.035172] Write protecting the kernel text: 2576k
[    2.035205] Write protecting the kernel read-only data: 936k
[    2.045579] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[    2.254759] fuse init (API version 7.9)
[    2.552740] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[    2.556776] processor ACPI0007:00: registered as cooling_device0
[    2.556781] ACPI: Processor [CPU] (supports 8 throttling states)
[    2.560979] Marking TSC unstable due to TSC halts in idle
[    2.562229] thermal LNXTHERM:01: registered as thermal_zone0
[    2.564701] ACPI: Thermal Zone [THM0] (57 C)
[    2.799361] ACPI: ACPI Dock Station Driver
[    3.254204] usbcore: registered new interface driver usbfs
[    3.254239] usbcore: registered new interface driver hub
[    3.258136] usbcore: registered new device driver usb
[    3.261246] USB Universal Host Controller Interface driver v3.0
[    3.261853] uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[    3.261865] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    3.261876] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    3.261881] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    3.261934] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[    3.261973] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00001820
[    3.262190] usb usb1: configuration #1 chosen from 1 choice
[    3.262225] hub 1-0:1.0: USB hub found
[    3.262234] hub 1-0:1.0: 2 ports detected
[    3.364895] uhci_hcd 0000:00:1d.1: power state changed by ACPI to D0
[    3.364913] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    3.364925] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    3.364930] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    3.364961] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[    3.365002] uhci_hcd 0000:00:1d.1: irq 17, io base 0x00001840
[    3.365119] usb usb2: configuration #1 chosen from 1 choice
[    3.365156] hub 2-0:1.0: USB hub found
[    3.365165] hub 2-0:1.0: 2 ports detected
[    3.448963] SCSI subsystem initialized
[    3.529097] libata version 3.00 loaded.
[    3.572797] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    3.572812] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    3.572817] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    3.572849] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[    3.572889] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001860
[    3.573024] usb usb3: configuration #1 chosen from 1 choice
[    3.573058] hub 3-0:1.0: USB hub found
[    3.573067] hub 3-0:1.0: 2 ports detected
[    3.676406] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[    3.676420] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    3.676425] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    3.676454] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[    3.676493] uhci_hcd 0000:00:1d.3: irq 19, io base 0x00001880
[    3.676617] usb usb4: configuration #1 chosen from 1 choice
[    3.676651] hub 4-0:1.0: USB hub found
[    3.676659] hub 4-0:1.0: 2 ports detected
[    3.684026] usb 2-1: new full speed USB device using uhci_hcd and address 2
[    3.781795] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0
[    3.781810] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[    3.781826] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    3.781831] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    3.781870] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[    3.785778] ehci_hcd 0000:00:1d.7: debug port 1
[    3.785786] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[    3.785796] ehci_hcd 0000:00:1d.7: irq 19, io mem 0xa0040000
[    3.808023] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    3.808217] usb usb5: configuration #1 chosen from 1 choice
[    3.808254] hub 5-0:1.0: USB hub found
[    3.808264] hub 5-0:1.0: 8 ports detected
[    4.016433] tg3.c:v3.94 (August 14, 2008)
[    4.016454] tg3 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    4.016468] tg3 0000:02:00.0: setting latency timer to 64
[    4.058174] eth0: Tigon3 [partno(BCM95751M) rev 4101 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:16:d3:2f:60:9a
[    4.058180] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
[    4.058184] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[    4.065889] ahci 0000:00:1f.2: version 3.0
[    4.065918] ahci: probe of 0000:00:1f.2 failed with error -22
[    4.071246] pata_acpi 0000:00:1f.2: setting latency timer to 64
[    4.077989] ata_piix 0000:00:1f.2: version 2.12
[    4.078001] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
[    4.208035] usb 2-1: device not accepting address 2, error -71
[    4.212025] Clocksource tsc unstable (delta = -103787390 ns)
[    4.232045] ata_piix 0000:00:1f.2: setting latency timer to 64
[    4.232129] scsi0 : ata_piix
[    4.232493] scsi1 : ata_piix
[    4.233897] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x1810 irq 14
[    4.233901] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15
[    4.264065] hub 2-0:1.0: unable to enumerate USB device on port 1
[    4.376036] usb 5-3: new high speed USB device using ehci_hcd and address 2
[    4.396445] ata1.00: ATA-6: HTC426060G9AT00, 00P3A0L2, max UDMA/100
[    4.396448] ata1.00: 117210240 sectors, multi 16: LBA 
[    4.396451] ata1.00: applying bridge limits
[    4.412445] ata1.00: configured for UDMA/100
[    4.509720] usb 5-3: configuration #1 chosen from 1 choice
[    4.509902] hub 5-3:1.0: USB hub found
[    4.510141] hub 5-3:1.0: 4 ports detected
[    4.568253] scsi 0:0:0:0: Direct-Access     ATA      HTC426060G9AT00  00P3 PQ: 0 ANSI: 5
[    4.579807] scsi 0:0:0:0: Attached scsi generic sg0 type 0
[    4.594187] Driver 'sd' needs updating - please use bus_type methods
[    4.594322] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB)
[    4.594351] sd 0:0:0:0: [sda] Write Protect is off
[    4.594355] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    4.594403] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.594498] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB)
[    4.594524] sd 0:0:0:0: [sda] Write Protect is off
[    4.594528] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    4.594576] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.594582]  sda: sda1 sda2 sda3 < sda5 >
[    4.735385] sd 0:0:0:0: [sda] Attached SCSI disk
[    4.808150] usb 5-3.1: new low speed USB device using ehci_hcd and address 3
[    4.922232] usb 5-3.1: configuration #1 chosen from 1 choice
[    5.008157] usb 5-3.4: new high speed USB device using ehci_hcd and address 4
[    5.117286] usb 5-3.4: configuration #1 chosen from 1 choice
[    5.117442] hub 5-3.4:1.0: USB hub found
[    5.117513] hub 5-3.4:1.0: 4 ports detected
[    5.416166] usb 5-3.4.3: new high speed USB device using ehci_hcd and address 5
[    5.543629] usb 5-3.4.3: configuration #1 chosen from 1 choice
[    5.543992] usbcore: registered new interface driver hiddev
[    5.547434] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1d.7/usb5/5-3/5-3.1/5-3.1:1.0/input/input2
[    5.560514] input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.7-3.1
[    5.560543] usbcore: registered new interface driver usbhid
[    5.560548] usbhid: v2.6:USB HID core driver
[    5.562157] usbcore: registered new interface driver libusual
[    5.574928] Initializing USB Mass Storage driver...
[    5.580522] scsi2 : SCSI emulation for USB Mass Storage devices
[    5.583528] usbcore: registered new interface driver usb-storage
[    5.583533] USB Mass Storage support registered.
[    5.583637] usb-storage: device found at 5
[    5.583639] usb-storage: waiting for device to settle before scanning
[    5.672823] PM: Starting manual resume from disk
[    5.672827] PM: Resume from partition 8:5
[    5.672830] PM: Checking hibernation image.
[    5.673016] PM: Resume from disk failed.
[    5.832344] kjournald starting.  Commit interval 5 seconds
[    5.832359] EXT3-fs: mounted filesystem with ordered data mode.
[   10.580272] usb-storage: device scan complete
[   10.617121] scsi 2:0:0:0: CD-ROM            HL-DT-ST DVDRAM GSA-E40L  SE01 PQ: 0 ANSI: 0
[   10.617684] scsi 2:0:0:0: Attached scsi generic sg1 type 5
[   20.521367] udevd version 124 started
[   21.383524] Linux agpgart interface v0.103
[   21.544460] agpgart-intel 0000:00:00.0: Intel 915GM Chipset
[   21.544906] agpgart-intel 0000:00:00.0: detected 7932K stolen memory
[   21.663423] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   21.676058] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000
[   21.723577] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   22.175329] intel_rng: FWH not detected
[   22.233603] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[   22.244040] ACPI: Power Button (FF) [PWRF]
[   22.244168] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input4
[   22.244729] ACPI: Lid Switch [LID]
[   22.244819] input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input5
[   22.260192] ACPI: Sleep Button (CM) [SLPB]
[   22.708950] iTCO_vendor_support: vendor-support=0
[   22.748245] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[   22.748930] iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x1060)
[   22.749128] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   23.457069] Yenta: CardBus bridge found at 0000:04:00.0 [1014:0555]
[   23.552651] ieee80211_crypt: registered algorithm 'NULL'
[   23.584824] Yenta: ISA IRQ mask 0x0cb8, PCI irq 16
[   23.584830] Socket status: 30000006
[   23.584835] pcmcia: parent PCI bridge I/O window: 0x2000 - 0x5fff
[   23.584862] cs: IO port probe 0x2000-0x5fff: clean.
[   23.585921] pcmcia: parent PCI bridge Memory window: 0xa0200000 - 0xafffffff
[   23.585925] pcmcia: parent PCI bridge Memory window: 0xd0000000 - 0xd7ffffff
[   23.668891] ieee80211: 802.11 data/management/control stack, git-1.1.13
[   23.668896] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[   23.761643] sdhci: Secure Digital Host Controller Interface driver
[   23.761647] sdhci: Copyright(c) Pierre Ossman
[   23.793852] sdhci-pci 0000:04:00.1: SDHCI controller found [1180:0822] (rev 13)
[   23.793876] sdhci-pci 0000:04:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[   23.810878] mmc0: SDHCI controller on PCI [0000:04:00.1] using PIO
[   25.934678] input: PC Speaker as /devices/platform/pcspkr/input/input6
[   25.972654] ACPI: AC Adapter [AC] (on-line)
[   26.014075] ACPI: \_SB_.PCI0.IDE0.SCND.MSTR: found ejectable bay
[   26.014083] ACPI: \_SB_.PCI0.IDE0.SCND.MSTR: Adding notify handler
[   26.063706] ACPI: \_SB_.PCI0.IDE0.SCND.MSTR: Is dependent on dock
[   26.063708] 
[   26.063712] ACPI: Bay [\_SB_.PCI0.IDE0.SCND.MSTR] Added
[   26.063722] ACPI: \_SB_.PCI0.IDE0.SCDM.MSTR: found ejectable bay
[   26.063729] ACPI: \_SB_.PCI0.IDE0.SCDM.MSTR: Adding notify handler
[   26.063773] ACPI: Error installing bay notify handler
[   26.117122] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
[   26.117127] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[   26.131085] ipw2200 0000:04:02.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[   26.133452] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[   26.133518] firmware: requesting ipw2200-bss.fw
[   26.147119] Non-volatile memory driver v1.2
[   26.284783] ACPI: Battery Slot [BAT0] (battery present)
[   26.368187] IBM TrackPoint firmware: 0x0e, buttons: 3/3
[   26.382548] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/input/input7
[   26.402289] irda_init()
[   26.402314] NET: Registered protocol family 23
[   26.598338] nsc-ircc 00:09: activated
[   26.598345] nsc_ircc_pnp_probe() : From PnP, found firbase 0x2F8 ; irq 3 ; dma 1.
[   26.598378] nsc-ircc, chip->init
[   26.598392] nsc-ircc, Found chip at base=0x164e
[   26.598429] nsc-ircc, driver loaded (Dag Brattli)
[   26.876575] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/input/input8
[   26.904232] ACPI: Video Device [VID] (multi-head: yes  rom: no  post: no)
[   27.057740] Driver 'sr' needs updating - please use bus_type methods
[   27.074508] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[   27.074515] Uniform CD-ROM driver Revision: 3.20
[   27.074647] sr 2:0:0:0: Attached scsi CD-ROM sr0
[   27.149065] thinkpad_acpi: ThinkPad ACPI Extras v0.21
[   27.149069] thinkpad_acpi: http://ibm-acpi.sf.net/
[   27.149072] thinkpad_acpi: ThinkPad BIOS 74ET61WW (2.06 ), EC 74HT26WW-1.01
[   27.149075] thinkpad_acpi: IBM ThinkPad X41, model 2525C3G
[   27.155050] Registered led device: tpacpi::thinklight
[   27.155266] thinkpad_acpi: another device driver is already handling bay events
[   27.155269] thinkpad_acpi: disabling subdriver bay
[   27.155325] Registered led device: tpacpi::power
[   27.155366] Registered led device: tpacpi:orange:batt
[   27.155411] Registered led device: tpacpi:green:batt
[   27.155453] Registered led device: tpacpi::dock_active
[   27.155492] Registered led device: tpacpi::bay_active
[   27.155531] Registered led device: tpacpi::dock_batt
[   27.155573] Registered led device: tpacpi::unknown_led
[   27.155615] Registered led device: tpacpi::standby
[   27.161642] thinkpad_acpi: CMOS NVRAM (7) and EC (0) do not agree on display brightness level
[   27.161933] input: ThinkPad Extra Buttons as /devices/virtual/input/input9
[   28.276177] ipw2200: Detected geography ZZR (14 802.11bg channels, 0 802.11a channels)
[   28.276245] Intel ICH 0000:00:1e.2: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[   28.276279] Intel ICH 0000:00:1e.2: setting latency timer to 64
[   28.276615] IrDA: Registered device irda0
[   28.276618] nsc-ircc, Using dongle: IBM31T1100 or Temic TFDS6000/TFDS6500
[   28.612599] cs: IO port probe 0x100-0x3af: clean.
[   28.614304] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[   28.615043] cs: IO port probe 0x820-0x8ff: clean.
[   28.615650] cs: IO port probe 0xc00-0xcf7: clean.
[   28.616549] cs: IO port probe 0xa00-0xaff: clean.
[   29.200057] intel8x0_measure_ac97_clock: measured 55486 usecs
[   29.200061] intel8x0: clocking to 48000
[   30.513176] lp: driver loaded but no devices found
[   30.815204] Adding 1799240k swap on /dev/sda5.  Priority:-1 extents:1 across:1799240k
[   31.574599] EXT3 FS on sda2, internal journal
[   33.442025] type=1505 audit(1225733820.253:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=4159
[   33.675333] type=1505 audit(1225733820.485:3): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=4164
[   33.675669] type=1505 audit(1225733820.485:4): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=4164
[   33.732957] type=1505 audit(1225733820.545:5): operation="profile_load" name="/usr/sbin/mysqld" name2="default" pid=4168
[   33.933667] ip_tables: (C) 2000-2006 Netfilter Core Team
[   34.773688] ACPI: WMI: Mapper loaded
[   36.426604] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[   37.310012] IBM machine detected. Enabling interrupts during APM calls.
[   37.310020] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[   37.310023] apm: overridden by ACPI.
[   37.573855] ppdev: user-space parallel port driver
[   39.662798] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[   39.662807] vboxdrv: Successfully done.
[   39.662810] vboxdrv: Found 1 processor cores.
[   39.665568] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[   39.665578] vboxdrv: Successfully loaded version 2.0.4_OSE (interface 0x00090000).
[   41.440435] NET: Registered protocol family 10
[   41.444491] lo: Disabled Privacy Extensions
[   43.790163] Bluetooth: Core ver 2.13
[   43.794103] NET: Registered protocol family 31
[   43.794115] Bluetooth: HCI device and connection manager initialized
[   43.794122] Bluetooth: HCI socket layer initialized
[   43.844693] Bluetooth: L2CAP ver 2.11
[   43.844706] Bluetooth: L2CAP socket layer initialized
[   43.869218] Bluetooth: SCO (Voice Link) ver 0.6
[   43.869226] Bluetooth: SCO socket layer initialized
[   43.905598] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   43.905605] Bluetooth: BNEP filters: protocol multicast
[   43.978431] Bluetooth: RFCOMM socket layer initialized
[   43.978672] Bluetooth: RFCOMM TTY layer initialized
[   43.978678] Bluetooth: RFCOMM ver 1.10
[   44.065047] Bridge firewalling registered
[   44.066748] pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
[   48.484640] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   48.584528] NET: Registered protocol family 17
[   50.082005] tg3: eth0: Link is up at 100 Mbps, full duplex.
[   50.082020] tg3: eth0: Flow control is on for TX and on for RX.
[   50.083324] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   59.368020] eth1: no IPv6 routers present
[   60.948016] eth0: no IPv6 routers present
[  128.398390] ecryptfs_parse_options: eCryptfs: unrecognized option 'rw'
[  128.398853] ecryptfs_parse_options: eCryptfs: unrecognized option 'user=tilo'
[  128.826648] padlock: VIA PadLock not detected.
[  180.250679] ieee80211_crypt: registered algorithm 'CCMP'
[  271.826723] type=1503 audit(1225734058.637:6): operation="inode_permission" requested_mask="r::" denied_mask="r::" fsuid=7 name="/proc/7913/net/" pid=7913 profile="/usr/sbin/cupsd"
[  273.116389] type=1503 audit(1225734059.929:7): operation="inode_permission" requested_mask="r::" denied_mask="r::" fsuid=7 name="/proc/7917/net/" pid=7917 profile="/usr/sbin/cupsd"
[  273.118753] type=1503 audit(1225734059.929:8): operation="socket_create" family="ax25" sock_type="dgram" protocol=0 pid=7917 profile="/usr/sbin/cupsd"
[  273.120288] type=1503 audit(1225734059.933:9): operation="socket_create" family="netrom" sock_type="seqpacket" protocol=0 pid=7917 profile="/usr/sbin/cupsd"
[  273.120631] type=1503 audit(1225734059.933:10): operation="socket_create" family="rose" sock_type="dgram" protocol=0 pid=7917 profile="/usr/sbin/cupsd"
[  273.122494] type=1503 audit(1225734059.933:11): operation="socket_create" family="ipx" sock_type="dgram" protocol=0 pid=7917 profile="/usr/sbin/cupsd"
[  273.124258] type=1503 audit(1225734059.937:12): operation="socket_create" family="appletalk" sock_type="dgram" protocol=0 pid=7917 profile="/usr/sbin/cupsd"
[  273.124578] type=1503 audit(1225734059.937:13): operation="socket_create" family="econet" sock_type="dgram" protocol=0 pid=7917 profile="/usr/sbin/cupsd"
[  273.124908] type=1503 audit(1225734059.937:14): operation="socket_create" family="ash" sock_type="dgram" protocol=0 pid=7917 profile="/usr/sbin/cupsd"
[  273.126787] type=1503 audit(1225734059.937:15): operation="socket_create" family="x25" sock_type="seqpacket" protocol=0 pid=7917 profile="/usr/sbin/cupsd"