USB_ModeSwitch log from Tue Nov 10 00:35:24 2015

Use global config file: /etc/usb_modeswitch.conf


Started via systemd
Adjust delay for USB storage devices ...
 Delay set to 24370336 seconds
Raw args from udev: 1-4

Bus ID for device not given by udev.
 Trying to determine it from kernel name (1-4) ...
Use top device dir /sys/bus/usb/devices/1-4

USB dir exists: /sys/bus/usb/devices/1-4

SCSI dir exists: /sys/bus/usb/devices/1-4
Warning: SCSI attribute "vendor" not readable.
Warning: SCSI attribute "model" not readable.
Warning: SCSI attribute "rev" not readable.
Use interface /sys/bus/usb/devices/1-4/1-4:1.0
----------------
USB values from sysfs:
  idVendor	19d2
  idProduct	2000
  manufacturer	ZTE,Incorporated
  product	ZTE WCDMA Technologies MSM
  serial	P671A2ZTED010000
  bNumConfigurations	1
  bConfigurationValue	1
  devnum	5
  busnum	1
----------------
bNumConfigurations is 1 - don't check for active configuration
Found packed config collection /usr/share/usb_modeswitch/configPack.tar.gz
Searching entries named: /usr/share/usb_modeswitch/19d2:2000*
Searching overriding entries named: /etc/usb_modeswitch.d/19d2:2000*
SCSI attributes not needed, move on.

Extract config 19d2:2000 from collection /usr/share/usb_modeswitch/configPack.tar.gz
config: TargetVendor set to 19d2
config: TargetProduct set to 0001,0002,0015,0016,0017,0019,0031,0033,0037,0042,0052,0055,0061,0063,0064,0066,0091,0108,0117,0128,0151,0157,0177,1402,2002,2003
Driver module is "option", ID path is /sys/bus/usb-serial/drivers/option1
! matched, now switching
Unbinding driver
Command to be run:
/usr/sbin/usb_modeswitch -W -D -s 20 -c /run/usb_modeswitch/current_cfg -u -1 -b 1 -g 5 -v 19d2 -p 2000 2>&1

Verbose debug output of usb_modeswitch and libusb follows
(Note that some USB errors are expected in the process)
--------------------------------

Read config file: /run/usb_modeswitch/current_cfg

 * usb_modeswitch: handle USB devices with multiple modes
 * Version 2.2.5 (C) Josua Dietze 2015
 * Based on libusb1/libusbx

 ! PLEASE REPORT NEW CONFIGURATIONS !

DefaultVendor=  0x19d2
DefaultProduct= 0x2000
TargetVendor=   0x19d2
TargetProductList="0001,0002,0015,0016,0017,0019,0031,0033,0037,0042,0052,0055,0061,0063,0064,0066,0091,0108,0117,0128,0151,0157,0177,1402,2002,2003"

StandardEject=1
MessageContent="55534243123456702000000080000c85010101180101010101000000000000"
NeedResponse=0
Success check enabled, max. wait time 20 seconds
System integration mode enabled

Use given bus/device number: 001/005 ...
Look for default devices ...
 bus/device number matched
  found USB ID 19d2:2000
   vendor ID matched
   product ID matched
 Found devices in default mode (1)
Use interface number 0
Use endpoints 0x01 (out) and 0x81 (in)

USB description data (for identification)
-------------------------
Manufacturer: ZTE,Incorporated
     Product: ZTE WCDMA Technologies MSM
  Serial No.: P671A2ZTED010000
-------------------------
Sending standard EJECT sequence
Looking for active driver ...
 OK, driver detached
Set up interface 0
Use endpoint 0x01 for message sending ...
Trying to send message 1 to endpoint 0x01 ...
 OK, message successfully sent
Read the response to message 1 (CSW) ...
 Response successfully read (13 bytes).
Trying to send message 2 to endpoint 0x01 ...
 OK, message successfully sent
Read the response to message 2 (CSW) ...
 Response successfully read (13 bytes).
Trying to send message 3 to endpoint 0x01 ...
 OK, message successfully sent
Read the response to message 3 (CSW) ...
 Response reading failed (error -9)
 Device is gone, skip any further commands
ok:busdev
--------------------------------
(end of usb_modeswitch output)
Check success of mode switch for max. 20 seconds ... Read attributes ... Read attributes ... Read attributes ... Read attributes ... Read attributes ... Read attributes ... Read attributes ...
USB dir exists: /sys/bus/usb/devices/1-4
 All attributes matched
Mode switching was successful, found 19d2:0016 (ZTE,Incorporated: ZTE WCDMA Technologies MSM)Now check for bound driver ...
 no driver has bound to interface 0 yet
Device not in "bind_list" yet, bind it now
Module loader is /sbin/modprobe
Module is active already
Try to add ID to driver "option"
 ID added to driver; check for new devices in /dev
 driver binding failed
Check for AVOID_RESET_QUIRK kernel attribute
 AVOID_RESET_QUIRK activated

All done, exit