[   36.889498] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   37.148478] hda_codec: ALC888: SKU not ready 0x411111f0
[   37.271010] input: HDA ATI SB Headphone as /devices/pci0000:00/0000:00:14.2/sound/card0/input4
[   38.391429] lp: driver loaded but no devices found
[   38.476844] ppdev: user-space parallel port driver
[   38.904438] cx25840 6-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
[   39.002843] tveeprom 6-00a2: Hauppauge model 75111, rev D1F5, serial# 7065976
[   39.002849] tveeprom 6-00a2: MAC address is 00:0d:fe:6b:d1:78
[   39.002852] tveeprom 6-00a2: tuner model is NXP 18271C2 (idx 155, type 54)
[   39.002856] tveeprom 6-00a2: TV standards NTSC(M) ATSC/DVB Digital (eeprom 0x88)
[   39.002859] tveeprom 6-00a2: audio processor is CX25843 (idx 37)
[   39.002862] tveeprom 6-00a2: decoder processor is CX25843 (idx 30)
[   39.002865] tveeprom 6-00a2: has radio, has IR receiver, has IR transmitter
[   39.002874] pvrusb2: Supported video standard(s) reported available in hardware: PAL-M/N/Nc;NTSC-M/Mj/Mk;ATSC-8VSB/16VSB
[   39.002879] pvrusb2: Mapping standards mask=0x300b700 (PAL-M/N/Nc;NTSC-M/Mj/Mk;ATSC-8VSB/16VSB)
[   39.002883] pvrusb2: Setting up 6 unique standard(s)
[   39.002887] pvrusb2: Set up standard idx=0 name=PAL-M
[   39.002889] pvrusb2: Set up standard idx=1 name=PAL-N
[   39.002892] pvrusb2: Set up standard idx=2 name=PAL-Nc
[   39.002894] pvrusb2: Set up standard idx=3 name=NTSC-M
[   39.002897] pvrusb2: Set up standard idx=4 name=NTSC-Mj
[   39.002900] pvrusb2: Set up standard idx=5 name=NTSC-Mk
[   39.002903] pvrusb2: Initial video standard (determined by device type): NTSC-M
[   39.002923] pvrusb2: Device initialization completed successfully.
[   39.003090] pvrusb2: registered device video0 [mpeg]
[   39.003096] DVB: registering new adapter (pvrusb2-dvb)
[   39.420889] cx25840 6-0044: 0x0000 is not a valid video input!
[   39.588291] DVB: registering adapter 0 frontend 0 (Samsung S5H1411 QAM/8VSB Frontend)...
[   39.589916] tda8290_probe: tda8290 couldn't read register 0x1f
[   39.590132] tda8295_probe: tda8290 couldn't read register 0x2f
[   39.641938] tda18271 6-0060: creating new instance
[   39.642273] tda18271_read_regs: [6-0060|M] ERROR: i2c_transfer returned: -5
[   39.642279] Unknown device (0) detected @ 6-0060, device not supported.
[   39.642282] tda18271_attach: [6-0060|M] error -22 on line 1270
[   39.642285] tda18271 6-0060: destroying instance
[   42.400034] eth0: no IPv6 routers present