[   28.795173] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   28.807710] sky2 0000:07:00.0 eth0: enabling interface
[   28.812764] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   28.814298] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   29.151663] init: plymouth-upstart-bridge main process (889) killed by TERM signal
[   35.111937] wlan0: authenticate with 64:0f:28:3d:6c:31
[   35.113811] wlan0: send auth to 64:0f:28:3d:6c:31 (try 1/3)
[   35.116614] wlan0: authenticated
[   35.116826] iwlwifi 0000:05:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[   35.116830] iwlwifi 0000:05:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[   35.116832] iwlwifi 0000:05:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[   35.116835] wlan0: waiting for beacon from 64:0f:28:3d:6c:31
[   35.212025] wlan0: associate with 64:0f:28:3d:6c:31 (try 1/3)
[   35.213801] wlan0: RX AssocResp from 64:0f:28:3d:6c:31 (capab=0x431 status=0 aid=1)
[   35.217255] wlan0: associated
[   35.217277] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   35.217346] cfg80211: Calling CRDA for country: US
[   35.222684] cfg80211: Regulatory domain changed to country: US
[   35.222688] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   35.222690] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   35.222692] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   35.222695] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   35.222697] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   35.222699] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   35.222701] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[  374.238087] show_signal_msg: 57 callbacks suppressed
[  374.238093] indicator-sync-[3072]: segfault at 2e67727a ip b755dcf7 sp bfac9538 error 4 in libgobject-2.0.so.0.3507.0[b752b000+50000]
[  596.744217] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 1066.728130] usb 2-3: new high-speed USB device number 3 using ehci-pci
[ 1066.895566] usb 2-3: New USB device found, idVendor=0930, idProduct=6544
[ 1066.895576] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1066.895584] usb 2-3: Product: DT 101 G2       
[ 1066.895590] usb 2-3: Manufacturer: Kingston
[ 1066.895597] usb 2-3: SerialNumber: 00137299803FC0B03564F798
[ 1066.966548] Initializing USB Mass Storage driver...
[ 1066.966687] scsi4 : usb-storage 2-3:1.0
[ 1066.966992] usbcore: registered new interface driver usb-storage
[ 1066.966995] USB Mass Storage support registered.
[ 1067.964728] scsi 4:0:0:0: Direct-Access     Kingston DT 101 G2        1.00 PQ: 0 ANSI: 2
[ 1067.965386] sd 4:0:0:0: Attached scsi generic sg2 type 0
[ 1067.966088] sd 4:0:0:0: [sdb] 3913664 512-byte logical blocks: (2.00 GB/1.86 GiB)
[ 1067.968322] sd 4:0:0:0: [sdb] Write Protect is off
[ 1067.968326] sd 4:0:0:0: [sdb] Mode Sense: 0b 00 00 08
[ 1067.968815] sd 4:0:0:0: [sdb] No Caching mode page present
[ 1067.968819] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 1067.971689] sd 4:0:0:0: [sdb] No Caching mode page present
[ 1067.971693] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 1067.972408]  sdb: sdb1
[ 1067.975461] sd 4:0:0:0: [sdb] No Caching mode page present
[ 1067.975466] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 1067.975469] sd 4:0:0:0: [sdb] Attached SCSI removable disk