package:snort:2.9.7.0-5
Setting up snort (2.9.7.0-5) ...
[?1049h[?25l(B






















Package configuration┌───────────────────────────┤ Configuring snort ├───────────────────────────┐│                                                                           │ │ This value is usually "eth0", but this may be inappropriate in some         │ network environments; for a dialup connection "ppp0" might be more          │ appropriate (see the output of "/sbin/ifconfig").                           │                                                                             │ Typically, this is the same interface as the "default route" is on. You     │ can determine which interface is used for this by running "/sbin/route      │ -n" (look for  "0.0.0.0").                                                   │                                                                             │ It is also not uncommon to use an interface with no IP address              │ configured in promiscuous mode. For such cases, select the interface in     │ this system that is physically connected to the network that should be      │ inspected, enable promiscuous mode later on and make sure that the          │ network traffic is sent to this interface (either connected to a "port      │ mirroring/spanning" port in a switch, to a hub, or to a tap).               │                                                                             │                                  <Ok>                                        │                                                                           │ └───────────────────────────────────────────────────────────────────────────┘                                                                              <Ok>[?12l[?25h



(B

[?1049l[?1049h[?25l(B






















[?25l[?12l[?25hPackage configuration┌────────────┤ Configuring snort ├────────────┐│ Interface(s) which Snort should listen on:  │ │                                             │ │ wlp2s0_____________________________________ │ │                                             │ │                   <Ok>                      │ │                                             │ └─────────────────────────────────────────────┘                                                [?25l<Ok>[?12l[?25h(B

[?1049lJob for snort.service failed b ecause the control process exited with error code.
See "systemctl  status snort.service" and "journalctl  -xe" for details.
invoke-rc.d: initscript snort, action "start" failed.
● snort.service - LSB: Lightweight network intrusion detection system
   Loaded: loaded (/etc/init.d/snort; generated; vendor preset: enabled)
   Active: failed (Result: exit-code) since Fri 2018-02-09 01:00:48 WIB; 14ms ago
     Docs: man:systemd-sysv-generator(8)
  Process: 7398 ExecStart=/etc/init.d/snort start (code=exited, status=1/FAILURE)

Feb 09 01:00:48 init5-Satellite-L740 snort[7407]: Initializing Output Plugins!
Feb 09 01:00:48 init5-Satellite-L740 snort[7407]: Initializing Preprocessors!
Feb 09 01:00:48 init5-Satellite-L740 snort[7407]: Initializing Plug-ins!
Feb 09 01:00:48 init5-Satellite-L740 snort[7407]: Parsing Rules file "/etc/snort/snort.conf"
Feb 09 01:00:48 init5-Satellite-L740 snort[7407]: FATAL ERROR: /etc/snort/snort.conf(0) Unable to open rules file "/etc/snort/snort.conf": No such file or directory.
Feb 09 01:00:48 init5-Satellite-L740 snort[7398]:    ...fail!
Feb 09 01:00:48 init5-Satellite-L740 systemd[1]: snort.service: Control process exited, code=exited status=1
Feb 09 01:00:48 init5-Satellite-L740 systemd[1]: Failed to start LSB: Lightweight network intrusion detection system.
Feb 09 01:00:48 init5-Satellite-L740 systemd[1]: snort.service: Unit entered failed state.
Feb 09 01:00:48 init5-Satellite-L740 systemd[1]: snort.service: Failed with result 'exit-code'.
dpkg: error processing package snort (--configure):
 subprocess installed post-installation script returned error exit status 1