[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.0.0-16-generic (buildd@roseapple) (gcc version 4.6.1 (Ubuntu/Linaro 4.6.1-9ubuntu3) ) #29-Ubuntu SMP Tue Feb 14 12:48:51 UTC 2012 (Ubuntu 3.0.0-16.29-generic 3.0.20) [ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.0.0-16-generic root=UUID=ab49260a-c922-44e8-9686-9e7848aad0ab ro quiet splash vt.handoff=7 [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] AMD AuthenticAMD [ 0.000000] Centaur CentaurHauls [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000cff90000 (usable) [ 0.000000] BIOS-e820: 00000000cff90000 - 00000000cff9e000 (ACPI data) [ 0.000000] BIOS-e820: 00000000cff9e000 - 00000000cffe0000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000cffe0000 - 00000000d0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) [ 0.000000] BIOS-e820: 0000000100000000 - 0000000320000000 (usable) [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] DMI present. [ 0.000000] DMI: MICRO-STAR INTERNATIONAL CO.,LTD MS-7596/760GM -E51 (MS-7596), BIOS V1.8 09/03/2010 [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved) [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable) [ 0.000000] No AGP bridge found [ 0.000000] last_pfn = 0x320000 max_arch_pfn = 0x400000000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-EFFFF uncachable [ 0.000000] F0000-FFFFF write-protect [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 000000000000 mask FFFF80000000 write-back [ 0.000000] 1 base 000080000000 mask FFFFC0000000 write-back [ 0.000000] 2 base 0000C0000000 mask FFFFF0000000 write-back [ 0.000000] 3 disabled [ 0.000000] 4 disabled [ 0.000000] 5 disabled [ 0.000000] 6 disabled [ 0.000000] 7 disabled [ 0.000000] TOM2: 0000000330000000 aka 13056M [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 [ 0.000000] e820 update range: 00000000d0000000 - 0000000100000000 (usable) ==> (reserved) [ 0.000000] last_pfn = 0xcff90 max_arch_pfn = 0x400000000 [ 0.000000] found SMP MP-table at [ffff8800000ff780] ff780 [ 0.000000] initial memory mapped : 0 - 20000000 [ 0.000000] Base memory trampoline at [ffff88000009a000] 9a000 size 20480 [ 0.000000] Using GB pages for direct mapping [ 0.000000] init_memory_mapping: 0000000000000000-00000000cff90000 [ 0.000000] 0000000000 - 00c0000000 page 1G [ 0.000000] 00c0000000 - 00cfe00000 page 2M [ 0.000000] 00cfe00000 - 00cff90000 page 4k [ 0.000000] kernel direct mapping tables up to cff90000 @ 1fffd000-20000000 [ 0.000000] init_memory_mapping: 0000000100000000-0000000320000000 [ 0.000000] 0100000000 - 0300000000 page 1G [ 0.000000] 0300000000 - 0320000000 page 2M [ 0.000000] kernel direct mapping tables up to 320000000 @ cff8e000-cff90000 [ 0.000000] RAMDISK: 365be000 - 372d7000 [ 0.000000] ACPI: RSDP 00000000000faaf0 00014 (v00 ACPIAM) [ 0.000000] ACPI: RSDT 00000000cff90000 00040 (v01 7596MS A7596100 20100903 MSFT 00000097) [ 0.000000] ACPI: FACP 00000000cff90200 00084 (v01 7596MS A7596100 20100903 MSFT 00000097) [ 0.000000] ACPI Warning: Optional field Pm2ControlBlock has zero address or length: 0x0000000000000000/0x1 (20110413/tbfadt-560) [ 0.000000] ACPI: DSDT 00000000cff905d0 09315 (v01 A7596 A7596100 00000100 INTL 20051117) [ 0.000000] ACPI: FACS 00000000cff9e000 00040 [ 0.000000] ACPI: APIC 00000000cff90390 0007C (v01 7596MS A7596100 20100903 MSFT 00000097) [ 0.000000] ACPI: MCFG 00000000cff90410 0003C (v01 7596MS OEMMCFG 20100903 MSFT 00000097) [ 0.000000] ACPI: OEMB 00000000cff9e040 00072 (v01 7596MS A7596100 20100903 MSFT 00000097) [ 0.000000] ACPI: SRAT 00000000cff9a5d0 00108 (v03 AMD FAM_F_10 00000002 AMD 00000001) [ 0.000000] ACPI: HPET 00000000cff9a6e0 00038 (v01 7596MS OEMHPET 20100903 MSFT 00000097) [ 0.000000] ACPI: SSDT 00000000cff9a720 00DA4 (v01 A M I POWERNOW 00000001 AMD 00000001) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] SRAT: PXM 0 -> APIC 0x00 -> Node 0 [ 0.000000] SRAT: PXM 0 -> APIC 0x01 -> Node 0 [ 0.000000] SRAT: PXM 0 -> APIC 0x02 -> Node 0 [ 0.000000] SRAT: PXM 0 -> APIC 0x03 -> Node 0 [ 0.000000] SRAT: PXM 0 -> APIC 0x04 -> Node 0 [ 0.000000] SRAT: PXM 0 -> APIC 0x05 -> Node 0 [ 0.000000] SRAT: Node 0 PXM 0 0-a0000 [ 0.000000] SRAT: Node 0 PXM 0 100000-d0000000 [ 0.000000] SRAT: Node 0 PXM 0 100000000-330000000 [ 0.000000] NUMA: Node 0 [0,a0000) + [100000,d0000000) -> [0,d0000000) [ 0.000000] NUMA: Node 0 [0,d0000000) + [100000000,320000000) -> [0,320000000) [ 0.000000] Initmem setup node 0 0000000000000000-0000000320000000 [ 0.000000] NODE_DATA [000000031fffb000 - 000000031fffffff] [ 0.000000] [ffffea0000000000-ffffea000affffff] PMD -> [ffff880313a00000-ffff88031dffffff] on node 0 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000010 -> 0x00001000 [ 0.000000] DMA32 0x00001000 -> 0x00100000 [ 0.000000] Normal 0x00100000 -> 0x00320000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[3] active PFN ranges [ 0.000000] 0: 0x00000010 -> 0x0000009f [ 0.000000] 0: 0x00000100 -> 0x000cff90 [ 0.000000] 0: 0x00100000 -> 0x00320000 [ 0.000000] On node 0 totalpages: 3079967 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 5 pages reserved [ 0.000000] DMA zone: 3922 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 14280 pages used for memmap [ 0.000000] DMA32 zone: 833480 pages, LIFO batch:31 [ 0.000000] Normal zone: 30464 pages used for memmap [ 0.000000] Normal zone: 2197760 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled) [ 0.000000] ACPI: IOAPIC (id[0x06] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 6, version 33, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x8300 base: 0xfed00000 [ 0.000000] SMP: Allowing 6 CPUs, 0 hotplug CPUs [ 0.000000] nr_irqs_gsi: 40 [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e6000 [ 0.000000] PM: Registered nosave memory: 00000000000e6000 - 0000000000100000 [ 0.000000] PM: Registered nosave memory: 00000000cff90000 - 00000000cff9e000 [ 0.000000] PM: Registered nosave memory: 00000000cff9e000 - 00000000cffe0000 [ 0.000000] PM: Registered nosave memory: 00000000cffe0000 - 00000000d0000000 [ 0.000000] PM: Registered nosave memory: 00000000d0000000 - 00000000fff00000 [ 0.000000] PM: Registered nosave memory: 00000000fff00000 - 0000000100000000 [ 0.000000] Allocating PCI resources starting at d0000000 (gap: d0000000:2ff00000) [ 0.000000] Booting paravirtualized kernel on bare hardware [ 0.000000] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:6 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 27 pages/cpu @ffff88031fc00000 s79616 r8192 d22784 u262144 [ 0.000000] pcpu-alloc: s79616 r8192 d22784 u262144 alloc=1*2097152 [ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 - - [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 3035162 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.0.0-16-generic root=UUID=ab49260a-c922-44e8-9686-9e7848aad0ab ro quiet splash vt.handoff=7 [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Checking aperture... [ 0.000000] No AGP bridge found [ 0.000000] Node 0: aperture @ 4834000000 size 32 MB [ 0.000000] Aperture beyond 4GB. Ignoring. [ 0.000000] Your BIOS doesn't leave a aperture memory hole [ 0.000000] Please enable the IOMMU option in the BIOS setup [ 0.000000] This costs you 64 MB of RAM [ 0.000000] Mapping aperture over 65536 KB of RAM @ c4000000 [ 0.000000] PM: Registered nosave memory: 00000000c4000000 - 00000000c8000000 [ 0.000000] Memory: 11988620k/13107200k available (6140k kernel code, 787332k absent, 331248k reserved, 6894k data, 988k init) [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled. [ 0.000000] NR_IRQS:16640 nr_irqs:728 16 [ 0.000000] spurious 8259A interrupt: IRQ7. [ 0.000000] vt handoff: transparent VT on vt#7 [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] allocated 98566144 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] hpet clockevent registered [ 0.000000] Fast TSC calibration using PIT [ 0.000000] Detected 3300.329 MHz processor. [ 0.008004] Calibrating delay loop (skipped), value calculated using timer frequency.. 6600.65 BogoMIPS (lpj=13201316) [ 0.008007] pid_max: default: 32768 minimum: 301 [ 0.008027] Security Framework initialized [ 0.008039] AppArmor: AppArmor initialized [ 0.008040] Yama: becoming mindful. [ 0.009051] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes) [ 0.017139] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.019580] Mount-cache hash table entries: 256 [ 0.019683] Initializing cgroup subsys cpuacct [ 0.019687] Initializing cgroup subsys memory [ 0.019695] Initializing cgroup subsys devices [ 0.019696] Initializing cgroup subsys freezer [ 0.019697] Initializing cgroup subsys net_cls [ 0.019699] Initializing cgroup subsys blkio [ 0.019705] Initializing cgroup subsys perf_event [ 0.019726] tseg: 0000000000 [ 0.019736] CPU: Physical Processor ID: 0 [ 0.019737] CPU: Processor Core ID: 0 [ 0.019739] mce: CPU supports 6 MCE banks [ 0.019746] using AMD E400 aware idle routine [ 0.020813] ACPI: Core revision 20110413 [ 0.024011] ftrace: allocating 25748 entries in 101 pages [ 0.028421] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.070827] CPU0: AMD Phenom(tm) II X6 1100T Processor stepping 00 [ 0.072003] Performance Events: AMD PMU driver. [ 0.072003] ... version: 0 [ 0.072003] ... bit width: 48 [ 0.072003] ... generic registers: 4 [ 0.072003] ... value mask: 0000ffffffffffff [ 0.072003] ... max period: 00007fffffffffff [ 0.072003] ... fixed-purpose events: 0 [ 0.072003] ... event mask: 000000000000000f [ 0.072003] Booting Node 0, Processors #1 [ 0.072003] smpboot cpu 1: start_ip = 9a000 [ 0.160021] System has AMD C1E enabled [ 0.160036] Switch to broadcast mode on CPU1 [ 0.160060] #2 [ 0.160061] smpboot cpu 2: start_ip = 9a000 [ 0.252029] Switch to broadcast mode on CPU2 [ 0.252072] #3 [ 0.252073] smpboot cpu 3: start_ip = 9a000 [ 0.344037] Switch to broadcast mode on CPU3 [ 0.344094] #4 [ 0.344095] smpboot cpu 4: start_ip = 9a000 [ 0.436043] Switch to broadcast mode on CPU4 [ 0.436107] #5 Ok. [ 0.436108] smpboot cpu 5: start_ip = 9a000 [ 0.528058] Brought up 6 CPUs [ 0.528068] Total of 6 processors activated (39602.23 BogoMIPS). [ 0.528049] Switch to broadcast mode on CPU5 [ 0.531646] Switch to broadcast mode on CPU0 [ 0.531646] devtmpfs: initialized [ 0.531646] PM: Registering ACPI NVS region at cff9e000 (270336 bytes) [ 0.532822] print_constraints: dummy: [ 0.532844] Time: 12:40:23 Date: 03/17/12 [ 0.532870] NET: Registered protocol family 16 [ 0.532954] node 0 link 0: io port [1000, ffffff] [ 0.532956] TOM: 00000000d0000000 aka 3328M [ 0.532958] Fam 10h mmconf [mem 0xe0000000-0xefffffff] [ 0.532965] node 0 link 0: mmio [a0000, bffff] [ 0.532980] node 0 link 0: mmio [d0000000, efffffff] ==> [d0000000, dfffffff] [ 0.532982] node 0 link 0: mmio [f0000000, fe7fffff] [ 0.532984] node 0 link 0: mmio [fe800000, fe9fffff] [ 0.532986] node 0 link 0: mmio [fea00000, ffefffff] [ 0.532987] TOM2: 0000000330000000 aka 13056M [ 0.532989] bus: [00, 07] on node 0 link 0 [ 0.532990] bus: 00 index 0 [io 0x0000-0xffff] [ 0.532991] bus: 00 index 1 [mem 0x000a0000-0x000bffff] [ 0.532993] bus: 00 index 2 [mem 0xd0000000-0xdfffffff] [ 0.532994] bus: 00 index 3 [mem 0xf0000000-0xffffffff] [ 0.532995] bus: 00 index 4 [mem 0x330000000-0xfcffffffff] [ 0.533004] Extended Config Space enabled on 1 nodes [ 0.533048] ACPI: bus type pci registered [ 0.532878] Trying to unpack rootfs image as initramfs... [ 0.533089] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000) [ 0.533091] PCI: not using MMCONFIG [ 0.533093] PCI: Using configuration type 1 for base access [ 0.533094] PCI: Using configuration type 1 for extended access [ 0.533567] bio: create slab at 0 [ 0.533567] ACPI: EC: Detected MSI hardware, enabling workarounds. [ 0.533567] ACPI: EC: Look up EC in DSDT [ 0.533567] ACPI: Executed 4 blocks of module-level executable AML code [ 0.576309] ACPI: Interpreter enabled [ 0.576313] ACPI: (supports S0 S1 S4 S5) [ 0.576327] ACPI: Using IOAPIC for interrupt routing [ 0.576362] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000) [ 0.576853] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources [ 0.696285] Freeing initrd memory: 13412k freed [ 0.748902] ACPI: No dock devices found. [ 0.748904] HEST: Table not found. [ 0.748907] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.748963] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.749057] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] [ 0.749058] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] [ 0.749060] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] [ 0.749061] pci_root PNP0A03:00: host bridge window [mem 0x000d0000-0x000dffff] [ 0.749062] pci_root PNP0A03:00: host bridge window [mem 0xd0000000-0xdfffffff] [ 0.749064] pci_root PNP0A03:00: host bridge window [mem 0xf0000000-0xfebfffff] [ 0.749074] pci 0000:00:00.0: [1022:9600] type 0 class 0x000600 [ 0.749114] pci 0000:00:01.0: [1022:9602] type 1 class 0x000604 [ 0.749147] pci 0000:00:05.0: [1022:9605] type 1 class 0x000604 [ 0.749173] pci 0000:00:05.0: PME# supported from D0 D3hot D3cold [ 0.749175] pci 0000:00:05.0: PME# disabled [ 0.749206] pci 0000:00:11.0: [1002:4390] type 0 class 0x000101 [ 0.749225] pci 0000:00:11.0: reg 10: [io 0xc000-0xc007] [ 0.749234] pci 0000:00:11.0: reg 14: [io 0xb000-0xb003] [ 0.749242] pci 0000:00:11.0: reg 18: [io 0xa000-0xa007] [ 0.749251] pci 0000:00:11.0: reg 1c: [io 0x9000-0x9003] [ 0.749259] pci 0000:00:11.0: reg 20: [io 0x8000-0x800f] [ 0.749268] pci 0000:00:11.0: reg 24: [mem 0xfe7ffc00-0xfe7fffff] [ 0.749286] pci 0000:00:11.0: set SATA to AHCI mode [ 0.749339] pci 0000:00:12.0: [1002:4397] type 0 class 0x000c03 [ 0.749351] pci 0000:00:12.0: reg 10: [mem 0xfe7fe000-0xfe7fefff] [ 0.749412] pci 0000:00:12.1: [1002:4398] type 0 class 0x000c03 [ 0.749423] pci 0000:00:12.1: reg 10: [mem 0xfe7fd000-0xfe7fdfff] [ 0.749488] pci 0000:00:12.2: [1002:4396] type 0 class 0x000c03 [ 0.749505] pci 0000:00:12.2: reg 10: [mem 0xfe7ff800-0xfe7ff8ff] [ 0.749582] pci 0000:00:12.2: supports D1 D2 [ 0.749583] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot [ 0.749587] pci 0000:00:12.2: PME# disabled [ 0.749605] pci 0000:00:13.0: [1002:4397] type 0 class 0x000c03 [ 0.749617] pci 0000:00:13.0: reg 10: [mem 0xfe7fc000-0xfe7fcfff] [ 0.749676] pci 0000:00:13.1: [1002:4398] type 0 class 0x000c03 [ 0.749688] pci 0000:00:13.1: reg 10: [mem 0xfe7fb000-0xfe7fbfff] [ 0.749753] pci 0000:00:13.2: [1002:4396] type 0 class 0x000c03 [ 0.749771] pci 0000:00:13.2: reg 10: [mem 0xfe7ff400-0xfe7ff4ff] [ 0.749848] pci 0000:00:13.2: supports D1 D2 [ 0.749850] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot [ 0.749853] pci 0000:00:13.2: PME# disabled [ 0.749874] pci 0000:00:14.0: [1002:4385] type 0 class 0x000c05 [ 0.749967] pci 0000:00:14.1: [1002:439c] type 0 class 0x000101 [ 0.749982] pci 0000:00:14.1: reg 10: [io 0x0000-0x0007] [ 0.749991] pci 0000:00:14.1: reg 14: [io 0x0000-0x0003] [ 0.749999] pci 0000:00:14.1: reg 18: [io 0x0000-0x0007] [ 0.750007] pci 0000:00:14.1: reg 1c: [io 0x0000-0x0003] [ 0.750016] pci 0000:00:14.1: reg 20: [io 0xff00-0xff0f] [ 0.750070] pci 0000:00:14.2: [1002:4383] type 0 class 0x000403 [ 0.750090] pci 0000:00:14.2: reg 10: [mem 0xfe7f4000-0xfe7f7fff 64bit] [ 0.750152] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold [ 0.750155] pci 0000:00:14.2: PME# disabled [ 0.750167] pci 0000:00:14.3: [1002:439d] type 0 class 0x000601 [ 0.750238] pci 0000:00:14.4: [1002:4384] type 1 class 0x000604 [ 0.750276] pci 0000:00:14.5: [1002:4399] type 0 class 0x000c03 [ 0.750288] pci 0000:00:14.5: reg 10: [mem 0xfe7fa000-0xfe7fafff] [ 0.750351] pci 0000:00:18.0: [1022:1200] type 0 class 0x000600 [ 0.750363] pci 0000:00:18.1: [1022:1201] type 0 class 0x000600 [ 0.750372] pci 0000:00:18.2: [1022:1202] type 0 class 0x000600 [ 0.750381] pci 0000:00:18.3: [1022:1203] type 0 class 0x000600 [ 0.750392] pci 0000:00:18.4: [1022:1204] type 0 class 0x000600 [ 0.750440] pci 0000:01:05.0: [1002:9616] type 0 class 0x000300 [ 0.750447] pci 0000:01:05.0: reg 10: [mem 0xd0000000-0xdfffffff pref] [ 0.750451] pci 0000:01:05.0: reg 14: [io 0xd000-0xd0ff] [ 0.750454] pci 0000:01:05.0: reg 18: [mem 0xfe9f0000-0xfe9fffff] [ 0.750462] pci 0000:01:05.0: reg 24: [mem 0xfe800000-0xfe8fffff] [ 0.750476] pci 0000:01:05.0: supports D1 D2 [ 0.750516] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 0.750518] pci 0000:00:01.0: bridge window [io 0xd000-0xdfff] [ 0.750520] pci 0000:00:01.0: bridge window [mem 0xfe800000-0xfe9fffff] [ 0.750523] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.750552] pci 0000:02:00.0: [10ec:8168] type 0 class 0x000200 [ 0.750563] pci 0000:02:00.0: reg 10: [io 0xe800-0xe8ff] [ 0.750582] pci 0000:02:00.0: reg 18: [mem 0xfdfff000-0xfdffffff 64bit pref] [ 0.750594] pci 0000:02:00.0: reg 20: [mem 0xfdff8000-0xfdffbfff 64bit pref] [ 0.750602] pci 0000:02:00.0: reg 30: [mem 0xfeae0000-0xfeafffff pref] [ 0.750645] pci 0000:02:00.0: supports D1 D2 [ 0.750647] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.750650] pci 0000:02:00.0: PME# disabled [ 0.756093] pci 0000:00:05.0: PCI bridge to [bus 02-02] [ 0.756107] pci 0000:00:05.0: bridge window [io 0xe000-0xefff] [ 0.756115] pci 0000:00:05.0: bridge window [mem 0xfea00000-0xfeafffff] [ 0.756125] pci 0000:00:05.0: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref] [ 0.756187] pci 0000:03:05.0: [168c:0023] type 0 class 0x000280 [ 0.756223] pci 0000:03:05.0: reg 10: [mem 0xfebf0000-0xfebfffff] [ 0.756398] pci 0000:00:14.4: PCI bridge to [bus 03-03] (subtractive decode) [ 0.756401] pci 0000:00:14.4: bridge window [io 0xf000-0x0000] (disabled) [ 0.756405] pci 0000:00:14.4: bridge window [mem 0xfeb00000-0xfebfffff] [ 0.756409] pci 0000:00:14.4: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) [ 0.756411] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7] (subtractive decode) [ 0.756412] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff] (subtractive decode) [ 0.756414] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode) [ 0.756415] pci 0000:00:14.4: bridge window [mem 0x000d0000-0x000dffff] (subtractive decode) [ 0.756417] pci 0000:00:14.4: bridge window [mem 0xd0000000-0xdfffffff] (subtractive decode) [ 0.756419] pci 0000:00:14.4: bridge window [mem 0xf0000000-0xfebfffff] (subtractive decode) [ 0.756433] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.756570] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] [ 0.756610] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE5._PRT] [ 0.756638] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PC._PRT] [ 0.756672] pci0000:00: Requesting ACPI _OSC control (0x1d) [ 0.756674] pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d [ 0.756675] ACPI _OSC control for PCIe not granted, disabling ASPM [ 0.759061] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 7 10 *11 12 14 15) [ 0.759086] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 7 *10 11 12 14 15) [ 0.759108] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 7 10 *11 12 14 15) [ 0.759130] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 7 *10 11 12 14 15) [ 0.759151] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 7 10 11 12 14 15) *0, disabled. [ 0.759173] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 7 10 11 12 14 15) *0, disabled. [ 0.759195] ACPI: PCI Interrupt Link [LNKG] (IRQs 4 *10 11 12 14 15) [ 0.759217] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 7 10 11 12 14 15) *0, disabled. [ 0.759286] vgaarb: device added: PCI:0000:01:05.0,decodes=io+mem,owns=io+mem,locks=none [ 0.759288] vgaarb: loaded [ 0.759289] vgaarb: bridge control possible 0000:01:05.0 [ 0.759407] SCSI subsystem initialized [ 0.759428] libata version 3.00 loaded. [ 0.759428] usbcore: registered new interface driver usbfs [ 0.759428] usbcore: registered new interface driver hub [ 0.759428] usbcore: registered new device driver usb [ 0.759428] PCI: Using ACPI for IRQ routing [ 0.767980] PCI: pci_cache_line_size set to 64 bytes [ 0.768037] reserve RAM buffer: 000000000009fc00 - 000000000009ffff [ 0.768052] reserve RAM buffer: 00000000cff90000 - 00000000cfffffff [ 0.768137] NetLabel: Initializing [ 0.768138] NetLabel: domain hash size = 128 [ 0.768139] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.768149] NetLabel: unlabeled traffic allowed by default [ 0.768182] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0 [ 0.768185] hpet0: 4 comparators, 32-bit 14.318180 MHz counter [ 0.770211] Switching to clocksource hpet [ 0.770229] Switched to NOHz mode on CPU #5 [ 0.770288] Switched to NOHz mode on CPU #0 [ 0.770213] Switched to NOHz mode on CPU #1 [ 0.770218] Switched to NOHz mode on CPU #2 [ 0.770225] Switched to NOHz mode on CPU #4 [ 0.770219] Switched to NOHz mode on CPU #3 [ 0.772069] AppArmor: AppArmor Filesystem Enabled [ 0.772083] pnp: PnP ACPI init [ 0.772091] ACPI: bus type pnp registered [ 0.772159] pnp 00:00: [bus 00-ff] [ 0.772161] pnp 00:00: [io 0x0cf8-0x0cff] [ 0.772162] pnp 00:00: [io 0x0000-0x0cf7 window] [ 0.772164] pnp 00:00: [io 0x0d00-0xffff window] [ 0.772165] pnp 00:00: [mem 0x000a0000-0x000bffff window] [ 0.772166] pnp 00:00: [mem 0x000d0000-0x000dffff window] [ 0.772168] pnp 00:00: [mem 0xd0000000-0xdfffffff window] [ 0.772169] pnp 00:00: [mem 0xf0000000-0xfebfffff window] [ 0.772200] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active) [ 0.772251] pnp 00:01: [mem 0x00000000-0xffffffffffffffff disabled] [ 0.772253] pnp 00:01: [mem 0x00000000-0xffffffffffffffff disabled] [ 0.772279] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.772301] pnp 00:02: [dma 4] [ 0.772302] pnp 00:02: [io 0x0000-0x000f] [ 0.772303] pnp 00:02: [io 0x0081-0x0083] [ 0.772305] pnp 00:02: [io 0x0087] [ 0.772306] pnp 00:02: [io 0x0089-0x008b] [ 0.772307] pnp 00:02: [io 0x008f] [ 0.772308] pnp 00:02: [io 0x00c0-0x00df] [ 0.772321] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active) [ 0.772326] pnp 00:03: [io 0x0070-0x0071] [ 0.772337] pnp 00:03: [irq 8] [ 0.772352] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.772358] pnp 00:04: [io 0x0061] [ 0.772370] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active) [ 0.772375] pnp 00:05: [io 0x00f0-0x00ff] [ 0.772378] pnp 00:05: [irq 13] [ 0.772391] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active) [ 0.772526] pnp 00:06: [io 0x03f8-0x03ff] [ 0.772530] pnp 00:06: [irq 4] [ 0.772531] pnp 00:06: [dma 0 disabled] [ 0.772564] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.772787] pnp 00:07: [io 0x0378-0x037f] [ 0.772790] pnp 00:07: [irq 7] [ 0.772791] pnp 00:07: [dma 0 disabled] [ 0.772858] pnp 00:07: Plug and Play ACPI device, IDs PNP0400 (active) [ 0.772871] pnp 00:08: [mem 0xfed00000-0xfed003ff] [ 0.772885] pnp 00:08: Plug and Play ACPI device, IDs PNP0103 (active) [ 0.772926] pnp 00:09: [io 0x0060] [ 0.772927] pnp 00:09: [io 0x0064] [ 0.772928] pnp 00:09: [mem 0xfec00000-0xfec00fff] [ 0.772930] pnp 00:09: [mem 0xfee00000-0xfee00fff] [ 0.772953] system 00:09: [mem 0xfec00000-0xfec00fff] could not be reserved [ 0.772955] system 00:09: [mem 0xfee00000-0xfee00fff] has been reserved [ 0.772957] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.773029] pnp 00:0a: [io 0x0010-0x001f] [ 0.773030] pnp 00:0a: [io 0x0022-0x003f] [ 0.773032] pnp 00:0a: [io 0x0062-0x0063] [ 0.773033] pnp 00:0a: [io 0x0065-0x006f] [ 0.773034] pnp 00:0a: [io 0x0072-0x007f] [ 0.773035] pnp 00:0a: [io 0x0080] [ 0.773036] pnp 00:0a: [io 0x0084-0x0086] [ 0.773037] pnp 00:0a: [io 0x0088] [ 0.773038] pnp 00:0a: [io 0x008c-0x008e] [ 0.773039] pnp 00:0a: [io 0x0090-0x009f] [ 0.773040] pnp 00:0a: [io 0x00a2-0x00bf] [ 0.773042] pnp 00:0a: [io 0x00b1] [ 0.773046] pnp 00:0a: [io 0x00e0-0x00ef] [ 0.773047] pnp 00:0a: [io 0x04d0-0x04d1] [ 0.773048] pnp 00:0a: [io 0x040b] [ 0.773049] pnp 00:0a: [io 0x04d6] [ 0.773050] pnp 00:0a: [io 0x0c00-0x0c01] [ 0.773051] pnp 00:0a: [io 0x0c14] [ 0.773052] pnp 00:0a: [io 0x0c50-0x0c51] [ 0.773053] pnp 00:0a: [io 0x0c52] [ 0.773054] pnp 00:0a: [io 0x0c6c] [ 0.773055] pnp 00:0a: [io 0x0c6f] [ 0.773057] pnp 00:0a: [io 0x0cd0-0x0cd1] [ 0.773058] pnp 00:0a: [io 0x0cd2-0x0cd3] [ 0.773059] pnp 00:0a: [io 0x0cd4-0x0cd5] [ 0.773060] pnp 00:0a: [io 0x0cd6-0x0cd7] [ 0.773061] pnp 00:0a: [io 0x0cd8-0x0cdf] [ 0.773062] pnp 00:0a: [io 0x0800-0x089f] [ 0.773063] pnp 00:0a: [io 0x0000-0xffffffffffffffff disabled] [ 0.773065] pnp 00:0a: [io 0x0b00-0x0b0f] [ 0.773066] pnp 00:0a: [io 0x0b20-0x0b3f] [ 0.773067] pnp 00:0a: [io 0x0900-0x090f] [ 0.773068] pnp 00:0a: [io 0x0910-0x091f] [ 0.773069] pnp 00:0a: [io 0xfe00-0xfefe] [ 0.773070] pnp 00:0a: [io 0x0060] [ 0.773071] pnp 00:0a: [io 0x0064] [ 0.773073] pnp 00:0a: [mem 0xffb80000-0xffbfffff] [ 0.773074] pnp 00:0a: [mem 0xfec10000-0xfec1001f] [ 0.773117] system 00:0a: [io 0x04d0-0x04d1] has been reserved [ 0.773119] system 00:0a: [io 0x040b] has been reserved [ 0.773120] system 00:0a: [io 0x04d6] has been reserved [ 0.773122] system 00:0a: [io 0x0c00-0x0c01] has been reserved [ 0.773123] system 00:0a: [io 0x0c14] has been reserved [ 0.773125] system 00:0a: [io 0x0c50-0x0c51] has been reserved [ 0.773126] system 00:0a: [io 0x0c52] has been reserved [ 0.773128] system 00:0a: [io 0x0c6c] has been reserved [ 0.773129] system 00:0a: [io 0x0c6f] has been reserved [ 0.773130] system 00:0a: [io 0x0cd0-0x0cd1] has been reserved [ 0.773132] system 00:0a: [io 0x0cd2-0x0cd3] has been reserved [ 0.773134] system 00:0a: [io 0x0cd4-0x0cd5] has been reserved [ 0.773135] system 00:0a: [io 0x0cd6-0x0cd7] has been reserved [ 0.773137] system 00:0a: [io 0x0cd8-0x0cdf] has been reserved [ 0.773138] system 00:0a: [io 0x0800-0x089f] has been reserved [ 0.773140] system 00:0a: [io 0x0b00-0x0b0f] has been reserved [ 0.773141] system 00:0a: [io 0x0b20-0x0b3f] has been reserved [ 0.773143] system 00:0a: [io 0x0900-0x090f] has been reserved [ 0.773145] system 00:0a: [io 0x0910-0x091f] has been reserved [ 0.773146] system 00:0a: [io 0xfe00-0xfefe] has been reserved [ 0.773148] system 00:0a: [mem 0xffb80000-0xffbfffff] has been reserved [ 0.773150] system 00:0a: [mem 0xfec10000-0xfec1001f] has been reserved [ 0.773152] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.773211] pnp 00:0b: [io 0x0000-0xffffffffffffffff disabled] [ 0.773213] pnp 00:0b: [io 0x0e80-0x0f5f] [ 0.773214] pnp 00:0b: [io 0x0ae0-0x0aef] [ 0.773238] system 00:0b: [io 0x0e80-0x0f5f] has been reserved [ 0.773240] system 00:0b: [io 0x0ae0-0x0aef] has been reserved [ 0.773242] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.773264] pnp 00:0c: [mem 0xe0000000-0xefffffff] [ 0.773288] system 00:0c: [mem 0xe0000000-0xefffffff] has been reserved [ 0.773290] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.776271] pnp 00:0d: [mem 0x00000000-0x0009ffff] [ 0.776273] pnp 00:0d: [mem 0x000c0000-0x000cffff] [ 0.776274] pnp 00:0d: [mem 0x000e0000-0x000fffff] [ 0.776276] pnp 00:0d: [mem 0x00100000-0xcfffffff] [ 0.776277] pnp 00:0d: [mem 0xfec00000-0xffffffff] [ 0.776317] system 00:0d: [mem 0x00000000-0x0009ffff] could not be reserved [ 0.776319] system 00:0d: [mem 0x000c0000-0x000cffff] could not be reserved [ 0.776320] system 00:0d: [mem 0x000e0000-0x000fffff] could not be reserved [ 0.776322] system 00:0d: [mem 0x00100000-0xcfffffff] could not be reserved [ 0.776323] system 00:0d: [mem 0xfec00000-0xffffffff] could not be reserved [ 0.776326] system 00:0d: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.776393] pnp: PnP ACPI: found 14 devices [ 0.776394] ACPI: ACPI bus type pnp unregistered [ 0.781702] PCI: max bus depth: 1 pci_try_num: 2 [ 0.781716] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 0.781719] pci 0000:00:01.0: bridge window [io 0xd000-0xdfff] [ 0.781721] pci 0000:00:01.0: bridge window [mem 0xfe800000-0xfe9fffff] [ 0.781723] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.781726] pci 0000:00:05.0: PCI bridge to [bus 02-02] [ 0.781728] pci 0000:00:05.0: bridge window [io 0xe000-0xefff] [ 0.781730] pci 0000:00:05.0: bridge window [mem 0xfea00000-0xfeafffff] [ 0.781732] pci 0000:00:05.0: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref] [ 0.781735] pci 0000:00:14.4: PCI bridge to [bus 03-03] [ 0.781736] pci 0000:00:14.4: bridge window [io disabled] [ 0.781741] pci 0000:00:14.4: bridge window [mem 0xfeb00000-0xfebfffff] [ 0.781744] pci 0000:00:14.4: bridge window [mem pref disabled] [ 0.781760] pci 0000:00:05.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 0.781763] pci 0000:00:05.0: setting latency timer to 64 [ 0.781769] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 0.781770] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 0.781772] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 0.781773] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff] [ 0.781774] pci_bus 0000:00: resource 8 [mem 0xd0000000-0xdfffffff] [ 0.781776] pci_bus 0000:00: resource 9 [mem 0xf0000000-0xfebfffff] [ 0.781777] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff] [ 0.781779] pci_bus 0000:01: resource 1 [mem 0xfe800000-0xfe9fffff] [ 0.781780] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.781782] pci_bus 0000:02: resource 0 [io 0xe000-0xefff] [ 0.781783] pci_bus 0000:02: resource 1 [mem 0xfea00000-0xfeafffff] [ 0.781785] pci_bus 0000:02: resource 2 [mem 0xfdf00000-0xfdffffff 64bit pref] [ 0.781787] pci_bus 0000:03: resource 1 [mem 0xfeb00000-0xfebfffff] [ 0.781788] pci_bus 0000:03: resource 4 [io 0x0000-0x0cf7] [ 0.781789] pci_bus 0000:03: resource 5 [io 0x0d00-0xffff] [ 0.781791] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff] [ 0.781792] pci_bus 0000:03: resource 7 [mem 0x000d0000-0x000dffff] [ 0.781793] pci_bus 0000:03: resource 8 [mem 0xd0000000-0xdfffffff] [ 0.781795] pci_bus 0000:03: resource 9 [mem 0xf0000000-0xfebfffff] [ 0.781821] NET: Registered protocol family 2 [ 0.782080] IP route cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.783763] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 0.786306] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.786622] TCP: Hash tables configured (established 524288 bind 65536) [ 0.786624] TCP reno registered [ 0.786642] UDP hash table entries: 8192 (order: 6, 262144 bytes) [ 0.786748] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes) [ 0.786922] NET: Registered protocol family 1 [ 0.786932] pci 0000:00:01.0: MSI quirk detected; subordinate MSI disabled [ 1.232171] pci 0000:01:05.0: Boot video device [ 1.232200] PCI: CLS 64 bytes, default 64 [ 1.233798] PCI-DMA: Disabling AGP. [ 1.233927] PCI-DMA: aperture base @ c4000000 size 65536 KB [ 1.233929] PCI-DMA: using GART IOMMU. [ 1.233931] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture [ 1.237684] audit: initializing netlink socket (disabled) [ 1.237700] type=2000 audit(1331988024.232:1): initialized [ 1.274620] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 1.322630] VFS: Disk quotas dquot_6.5.2 [ 1.322672] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 1.323100] fuse init (API version 7.16) [ 1.323147] msgmni has been set to 23570 [ 1.323654] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 1.323690] io scheduler noop registered [ 1.323691] io scheduler deadline registered [ 1.323713] io scheduler cfq registered (default) [ 1.323943] pcieport 0000:00:05.0: setting latency timer to 64 [ 1.324000] pcieport 0000:00:05.0: irq 40 for MSI/MSI-X [ 1.324096] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 1.324110] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 1.324196] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0 [ 1.324201] ACPI: Power Button [PWRB] [ 1.324227] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 1.324229] ACPI: Power Button [PWRF] [ 1.324257] ACPI: acpi_idle registered with cpuidle [ 1.324288] ACPI: processor limited to max C-state 1 [ 1.496369] ERST: Table is not found! [ 1.496415] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 1.516862] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 1.541935] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 1.542192] Linux agpgart interface v0.103 [ 1.542845] brd: module loaded [ 1.543104] loop: module loaded [ 1.543285] pata_acpi 0000:00:14.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.543305] pata_acpi 0000:00:14.1: setting latency timer to 64 [ 1.543684] Fixed MDIO Bus: probed [ 1.543698] PPP generic driver version 2.4.2 [ 1.543728] tun: Universal TUN/TAP device driver, 1.6 [ 1.543729] tun: (C) 1999-2004 Max Krasnyansky [ 1.543792] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.543917] ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 1.543957] ehci_hcd 0000:00:12.2: EHCI Host Controller [ 1.544015] ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1 [ 1.544025] ehci_hcd 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 1.544049] ehci_hcd 0000:00:12.2: debug port 1 [ 1.544069] ehci_hcd 0000:00:12.2: irq 17, io mem 0xfe7ff800 [ 1.556117] ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00 [ 1.556260] hub 1-0:1.0: USB hub found [ 1.556262] hub 1-0:1.0: 6 ports detected [ 1.556471] ehci_hcd 0000:00:13.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 1.556483] ehci_hcd 0000:00:13.2: EHCI Host Controller [ 1.556515] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2 [ 1.556522] ehci_hcd 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 1.556539] ehci_hcd 0000:00:13.2: debug port 1 [ 1.556556] ehci_hcd 0000:00:13.2: irq 19, io mem 0xfe7ff400 [ 1.568116] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00 [ 1.568242] hub 2-0:1.0: USB hub found [ 1.568244] hub 2-0:1.0: 6 ports detected [ 1.568307] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.568456] ohci_hcd 0000:00:12.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.568469] ohci_hcd 0000:00:12.0: OHCI Host Controller [ 1.568495] ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 3 [ 1.568516] ohci_hcd 0000:00:12.0: irq 16, io mem 0xfe7fe000 [ 1.628162] hub 3-0:1.0: USB hub found [ 1.628167] hub 3-0:1.0: 3 ports detected [ 1.628343] ohci_hcd 0000:00:12.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.628353] ohci_hcd 0000:00:12.1: OHCI Host Controller [ 1.628377] ohci_hcd 0000:00:12.1: new USB bus registered, assigned bus number 4 [ 1.628392] ohci_hcd 0000:00:12.1: irq 16, io mem 0xfe7fd000 [ 1.688157] hub 4-0:1.0: USB hub found [ 1.688162] hub 4-0:1.0: 3 ports detected [ 1.688339] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 1.688352] ohci_hcd 0000:00:13.0: OHCI Host Controller [ 1.688378] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 5 [ 1.688397] ohci_hcd 0000:00:13.0: irq 18, io mem 0xfe7fc000 [ 1.748157] hub 5-0:1.0: USB hub found [ 1.748162] hub 5-0:1.0: 3 ports detected [ 1.748334] ohci_hcd 0000:00:13.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 1.748345] ohci_hcd 0000:00:13.1: OHCI Host Controller [ 1.748368] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 6 [ 1.748382] ohci_hcd 0000:00:13.1: irq 18, io mem 0xfe7fb000 [ 1.808165] hub 6-0:1.0: USB hub found [ 1.808171] hub 6-0:1.0: 3 ports detected [ 1.808344] ohci_hcd 0000:00:14.5: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 1.808356] ohci_hcd 0000:00:14.5: OHCI Host Controller [ 1.808378] ohci_hcd 0000:00:14.5: new USB bus registered, assigned bus number 7 [ 1.808392] ohci_hcd 0000:00:14.5: irq 18, io mem 0xfe7fa000 [ 1.868165] hub 7-0:1.0: USB hub found [ 1.868170] hub 7-0:1.0: 2 ports detected [ 1.868244] uhci_hcd: USB Universal Host Controller Interface driver [ 1.868286] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 1.868663] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.868673] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 1.868789] mousedev: PS/2 mouse device common for all mice [ 1.868861] rtc_cmos 00:03: RTC can wake from S4 [ 1.868931] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 [ 1.868954] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs [ 1.869008] device-mapper: uevent: version 1.0.3 [ 1.869045] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com [ 1.869054] cpuidle: using governor ladder [ 1.869055] cpuidle: using governor menu [ 1.869056] EFI Variables Facility v0.08 2004-May-17 [ 1.869191] TCP cubic registered [ 1.869253] NET: Registered protocol family 10 [ 1.869526] NET: Registered protocol family 17 [ 1.869535] Registering the dns_resolver key type [ 1.869594] PM: Hibernation image not present or could not be loaded. [ 1.869600] registered taskstats version 1 [ 1.898907] Magic number: 4:662:683 [ 1.899043] rtc_cmos 00:03: setting system clock to 2012-03-17 12:40:25 UTC (1331988025) [ 1.899079] powernow-k8: Found 1 AMD Phenom(tm) II X6 1100T Processor (6 cpu cores) (version 2.20.00) [ 1.899101] powernow-k8: Core Performance Boosting: on. [ 1.899135] powernow-k8: 0 : pstate 0 (3300 MHz) [ 1.899136] powernow-k8: 1 : pstate 1 (2500 MHz) [ 1.899137] powernow-k8: 2 : pstate 2 (1700 MHz) [ 1.899138] powernow-k8: 3 : pstate 3 (800 MHz) [ 1.899970] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 1.899971] EDD information not available. [ 1.901080] Freeing unused kernel memory: 988k freed [ 1.901261] Write protecting the kernel read-only data: 12288k [ 1.905871] Freeing unused kernel memory: 2032k freed [ 1.909466] Freeing unused kernel memory: 1388k freed [ 1.924248] udevd[129]: starting version 173 [ 1.938115] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 1.938141] r8169 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.938183] r8169 0000:02:00.0: setting latency timer to 64 [ 1.938237] r8169 0000:02:00.0: irq 41 for MSI/MSI-X [ 1.938583] r8169 0000:02:00.0: eth0: RTL8168d/8111d at 0xffffc9000187c000, 6c:62:6d:c0:7e:22, XID 081000c0 IRQ 41 [ 1.938626] ahci 0000:00:11.0: version 3.0 [ 1.938644] ahci 0000:00:11.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 1.938689] ahci 0000:00:11.0: irq 42 for MSI/MSI-X [ 1.938789] ahci 0000:00:11.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode [ 1.938792] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc [ 1.940140] scsi0 : ahci [ 1.940380] scsi1 : ahci [ 1.941014] scsi2 : ahci [ 1.941358] scsi3 : ahci [ 1.941432] ata1: SATA max UDMA/133 abar m1024@0xfe7ffc00 port 0xfe7ffd00 irq 42 [ 1.941436] ata2: SATA max UDMA/133 abar m1024@0xfe7ffc00 port 0xfe7ffd80 irq 42 [ 1.941439] ata3: SATA max UDMA/133 abar m1024@0xfe7ffc00 port 0xfe7ffe00 irq 42 [ 1.941441] ata4: SATA max UDMA/133 abar m1024@0xfe7ffc00 port 0xfe7ffe80 irq 42 [ 1.944539] scsi4 : pata_atiixp [ 1.944641] scsi5 : pata_atiixp [ 1.944741] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14 [ 1.944743] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xff08 irq 15 [ 1.980172] usb 1-4: new high speed USB device number 4 using ehci_hcd [ 2.236157] Refined TSC clocksource calibration: 3300.137 MHz. [ 2.236171] Switching to clocksource tsc [ 2.260149] ata2: SATA link down (SStatus 0 SControl 300) [ 2.260201] ata3: SATA link down (SStatus 0 SControl 300) [ 2.404102] usb 3-1: new low speed USB device number 2 using ohci_hcd [ 2.432102] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 2.432146] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.435171] ata4.00: ATAPI: HL-DT-ST DVDRAM GH22NS50, TN03, max UDMA/100 [ 2.435981] ata1.00: ATA-8: WDC WD20EARS-00MVWB0, 51.0AB51, max UDMA/133 [ 2.435991] ata1.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA [ 2.438951] ata4.00: configured for UDMA/100 [ 2.439906] ata1.00: configured for UDMA/133 [ 2.440073] scsi 0:0:0:0: Direct-Access ATA WDC WD20EARS-00M 51.0 PQ: 0 ANSI: 5 [ 2.440201] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 2.440367] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 2.440428] sd 0:0:0:0: [sda] Write Protect is off [ 2.440430] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.440454] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.447543] scsi 3:0:0:0: CD-ROM HL-DT-ST DVDRAM GH22NS50 TN03 PQ: 0 ANSI: 5 [ 2.456607] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray [ 2.456610] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 2.456682] sr 3:0:0:0: Attached scsi CD-ROM sr0 [ 2.456724] sr 3:0:0:0: Attached scsi generic sg1 type 5 [ 2.490395] sda: sda1 sda2 sda3 [ 2.490699] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.586459] input: NOVATEK USB Keyboard as /devices/pci0000:00/0000:00:12.0/usb3/3-1/3-1:1.0/input/input2 [ 2.586513] generic-usb 0003:0603:00F2.0001: input,hidraw0: USB HID v1.10 Keyboard [NOVATEK USB Keyboard] on usb-0000:00:12.0-1/input0 [ 2.597332] input: NOVATEK USB Keyboard as /devices/pci0000:00/0000:00:12.0/usb3/3-1/3-1:1.1/input/input3 [ 2.597436] generic-usb 0003:0603:00F2.0002: input,hiddev0,hidraw1: USB HID v1.10 Device [NOVATEK USB Keyboard] on usb-0000:00:12.0-1/input1 [ 2.597447] usbcore: registered new interface driver usbhid [ 2.597448] usbhid: USB HID core driver [ 2.792822] EXT4-fs (sda2): INFO: recovery required on readonly filesystem [ 2.792825] EXT4-fs (sda2): write access will be enabled during recovery [ 2.856110] usb 3-2: new low speed USB device number 3 using ohci_hcd [ 3.034408] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:12.0/usb3/3-2/3-2:1.0/input/input4 [ 3.034472] generic-usb 0003:046D:C046.0003: input,hidraw2: USB HID v1.10 Mouse [Logitech USB Optical Mouse] on usb-0000:00:12.0-2/input0 [ 6.335590] EXT4-fs (sda2): orphan cleanup on readonly fs [ 6.335599] EXT4-fs (sda2): ext4_orphan_cleanup: deleting unreferenced inode 42991632 [ 6.335667] EXT4-fs (sda2): ext4_orphan_cleanup: deleting unreferenced inode 42991652 [ 6.335700] EXT4-fs (sda2): ext4_orphan_cleanup: deleting unreferenced inode 42991654 [ 6.335713] EXT4-fs (sda2): ext4_orphan_cleanup: deleting unreferenced inode 42991645 [ 6.335720] EXT4-fs (sda2): ext4_orphan_cleanup: deleting unreferenced inode 42991644 [ 6.335743] EXT4-fs (sda2): ext4_orphan_cleanup: deleting unreferenced inode 42991651 [ 6.335750] EXT4-fs (sda2): 6 orphan inodes deleted [ 6.335752] EXT4-fs (sda2): recovery complete [ 6.815008] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 8.936040] udevd[371]: starting version 173 [ 9.135186] Adding 12320200k swap on /dev/sda3. Priority:-1 extents:1 across:12320200k [ 9.717483] lp: driver loaded but no devices found [ 10.840378] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro [ 11.055904] parport_pc 00:07: reported by Plug and Play ACPI [ 11.055962] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] [ 11.072487] MCE: In-kernel MCE decoding enabled. [ 11.074923] wmi: Mapper loaded [ 11.088165] ACPI: resource piix4_smbus [io 0x0b00-0x0b07] conflicts with ACPI region SOR1 [io 0xb00-0xb0f] [ 11.088168] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 11.107404] EDAC MC: Ver: 2.1.0 [ 11.130422] AMD64 EDAC driver v3.4.0 [ 11.130635] EDAC amd64: DRAM ECC disabled. [ 11.130642] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load. [ 11.130643] Either enable ECC checking or force module loading by setting 'ecc_enable_override'. [ 11.130644] (Note that use of the override may cause unknown side effects.) [ 11.140426] SP5100 TCO timer: SP5100 TCO WatchDog Timer Driver v0.01 [ 11.140486] SP5100 TCO timer: mmio address 0xfec000f0 already in use [ 11.141921] cfg80211: Calling CRDA to update world regulatory domain [ 11.149273] ppdev: user-space parallel port driver [ 11.152380] lp0: using parport0 (interrupt-driven). [ 11.425090] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 11.606678] ath9k 0000:03:05.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 12.039946] ath: EEPROM regdomain: 0x809c [ 12.039948] ath: EEPROM indicates we should expect a country code [ 12.039949] ath: doing EEPROM country->regdmn map search [ 12.039950] ath: country maps to regdmn code: 0x52 [ 12.039951] ath: Country alpha2 being used: CN [ 12.039952] ath: Regpair used: 0x52 [ 12.039954] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule: [ 12.039956] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.039958] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule: [ 12.039959] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.039961] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule: [ 12.039962] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.039964] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule: [ 12.039965] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.039966] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule: [ 12.039968] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.039969] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule: [ 12.039971] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.039972] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule: [ 12.039974] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.039975] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule: [ 12.039977] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.039978] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule: [ 12.039980] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.039981] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule: [ 12.039983] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.039984] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule: [ 12.039985] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.039987] cfg80211: Disabling freq 2467 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 12.039988] cfg80211: Disabling freq 2472 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 12.039990] cfg80211: Disabling freq 2484 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 12.043715] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule: [ 12.043717] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (600 mBi, 2000 mBm) [ 12.043718] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule: [ 12.043720] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (600 mBi, 2000 mBm) [ 12.043721] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule: [ 12.043723] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (600 mBi, 2000 mBm) [ 12.043724] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule: [ 12.043726] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (600 mBi, 2000 mBm) [ 12.043727] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule: [ 12.043729] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (600 mBi, 2000 mBm) [ 12.043730] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule: [ 12.043732] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (600 mBi, 2000 mBm) [ 12.043733] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule: [ 12.043735] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (600 mBi, 2000 mBm) [ 12.043736] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule: [ 12.043737] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (600 mBi, 2000 mBm) [ 12.043739] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule: [ 12.043740] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (600 mBi, 2000 mBm) [ 12.043742] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule: [ 12.043743] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (600 mBi, 2000 mBm) [ 12.043745] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule: [ 12.043746] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (600 mBi, 2000 mBm) [ 12.043748] cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule: [ 12.043749] cfg80211: 2457000 KHz - 2482000 KHz @ KHz), (600 mBi, 2000 mBm) [ 12.043751] cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule: [ 12.043752] cfg80211: 2457000 KHz - 2482000 KHz @ KHz), (600 mBi, 2000 mBm) [ 12.043754] cfg80211: Updating information on frequency 2484 MHz for a 20 MHz width channel with regulatory rule: [ 12.043755] cfg80211: 2474000 KHz - 2494000 KHz @ KHz), (600 mBi, 2000 mBm) [ 12.072428] ieee80211 phy0: Selected rate control algorithm 'ath9k_rate_control' [ 12.072882] Registered led device: ath9k-phy0 [ 12.072888] ieee80211 phy0: Atheros AR5416 MAC/BB Rev:2 AR2133 RF Rev:81 mem=0xffffc90012600000, irq=20 [ 12.072918] cfg80211: Pending regulatory request, waiting for it to be processed... [ 12.222576] [drm] Initialized drm 1.1.0 20060810 [ 12.274075] [drm] radeon defaulting to kernel modesetting. [ 12.274077] [drm] radeon kernel modesetting enabled. [ 12.274301] radeon 0000:01:05.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 12.274306] radeon 0000:01:05.0: setting latency timer to 64 [ 12.274470] [drm] initializing kernel modesetting (RS780 0x1002:0x9616 0x1462:0x7501). [ 12.274492] [drm] register mmio base: 0xFE9F0000 [ 12.274493] [drm] register mmio size: 65536 [ 12.275086] ATOM BIOS: 113 [ 12.275101] radeon 0000:01:05.0: VRAM: 256M 0x00000000C0000000 - 0x00000000CFFFFFFF (256M used) [ 12.275103] radeon 0000:01:05.0: GTT: 512M 0x00000000A0000000 - 0x00000000BFFFFFFF [ 12.278406] [drm] Detected VRAM RAM=256M, BAR=256M [ 12.278410] [drm] RAM width 32bits DDR [ 12.278490] [TTM] Zone kernel: Available graphics memory: 6036196 kiB. [ 12.278491] [TTM] Zone dma32: Available graphics memory: 2097152 kiB. [ 12.278493] [TTM] Initializing pool allocator. [ 12.278517] [drm] radeon: 256M of VRAM memory ready [ 12.278518] [drm] radeon: 512M of GTT memory ready. [ 12.278530] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 12.278532] [drm] Driver supports precise vblank timestamp query. [ 12.278549] [drm] radeon: irq initialized. [ 12.278552] [drm] GART: num cpu pages 131072, num gpu pages 131072 [ 12.279163] [drm] Loading RS780 Microcode [ 12.429009] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule: [ 12.429012] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2000 mBm) [ 12.429013] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule: [ 12.429015] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2000 mBm) [ 12.429016] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule: [ 12.429018] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2000 mBm) [ 12.429019] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule: [ 12.429020] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2000 mBm) [ 12.429022] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule: [ 12.429023] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2000 mBm) [ 12.429024] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule: [ 12.429026] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2000 mBm) [ 12.429027] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule: [ 12.429028] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2000 mBm) [ 12.429029] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule: [ 12.429031] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2000 mBm) [ 12.429032] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule: [ 12.429033] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2000 mBm) [ 12.429034] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule: [ 12.429036] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2000 mBm) [ 12.429037] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule: [ 12.429038] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2000 mBm) [ 12.429039] cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule: [ 12.429041] cfg80211: 2457000 KHz - 2482000 KHz @ KHz), (300 mBi, 2000 mBm) [ 12.429042] cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule: [ 12.429043] cfg80211: 2457000 KHz - 2482000 KHz @ KHz), (300 mBi, 2000 mBm) [ 12.429045] cfg80211: Updating information on frequency 2484 MHz for a 20 MHz width channel with regulatory rule: [ 12.429046] cfg80211: 2474000 KHz - 2494000 KHz @ KHz), (300 mBi, 2000 mBm) [ 12.429049] cfg80211: World regulatory domain updated: [ 12.429050] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 12.429051] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 12.429052] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 12.429054] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 12.429055] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 12.429057] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 12.429064] cfg80211: Calling CRDA for country: CN [ 12.431454] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule: [ 12.431457] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.431458] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule: [ 12.431460] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.431461] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule: [ 12.431463] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.431464] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule: [ 12.431466] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.431467] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule: [ 12.431469] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.431470] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule: [ 12.431471] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.431473] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule: [ 12.431474] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.431476] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule: [ 12.431477] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.431479] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule: [ 12.431480] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.431481] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule: [ 12.431483] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.431484] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule: [ 12.431486] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.431487] cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule: [ 12.431489] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.431490] cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule: [ 12.431491] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 12.431493] cfg80211: Disabling freq 2484 MHz [ 12.431495] cfg80211: Regulatory domain changed to country: CN [ 12.431496] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 12.431498] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 12.431499] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (N/A, 3000 mBm) [ 12.641137] radeon 0000:01:05.0: WB enabled [ 12.672931] [drm] ring test succeeded in 1 usecs [ 12.673014] [drm] radeon: ib pool ready. [ 12.673077] [drm] ib test succeeded in 0 usecs [ 12.673329] [drm] Radeon Display Connectors [ 12.673331] [drm] Connector 0: [ 12.673332] [drm] VGA [ 12.673337] [drm] DDC: 0x7e40 0x7e40 0x7e44 0x7e44 0x7e48 0x7e48 0x7e4c 0x7e4c [ 12.673338] [drm] Encoders: [ 12.673339] [drm] CRT1: INTERNAL_KLDSCP_DAC1 [ 12.673340] [drm] Connector 1: [ 12.673341] [drm] DVI-D [ 12.673342] [drm] HPD3 [ 12.673343] [drm] DDC: 0x7e50 0x7e50 0x7e54 0x7e54 0x7e58 0x7e58 0x7e5c 0x7e5c [ 12.673344] [drm] Encoders: [ 12.673346] [drm] DFP3: INTERNAL_KLDSCP_LVTMA [ 12.683001] [drm] Radeon display connector VGA-1: No monitor connected or invalid EDID [ 12.734821] [drm] Radeon display connector DVI-D-1: Found valid EDID [ 12.734841] [drm] radeon: power management initialized [ 12.823329] [drm] fb mappable at 0xD0141000 [ 12.823331] [drm] vram apper at 0xD0000000 [ 12.823332] [drm] size 8294400 [ 12.823333] [drm] fb depth is 24 [ 12.823334] [drm] pitch is 7680 [ 12.823401] fbcon: radeondrmfb (fb0) is primary device [ 12.823575] Console: switching to colour frame buffer device 240x67 [ 12.823601] fb0: radeondrmfb frame buffer device [ 12.823602] drm: registered panic notifier [ 12.823607] [drm] Initialized radeon 2.10.0 20080528 for 0000:01:05.0 on minor 0 [ 12.939418] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 13.193727] hda_codec: ALC889: BIOS auto-probing. [ 13.206335] input: HDA ATI SB Headphone as /devices/pci0000:00/0000:00:14.2/sound/card0/input5 [ 14.278057] type=1400 audit(1331988037.873:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=780 comm="apparmor_parser" [ 14.278074] type=1400 audit(1331988037.873:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=782 comm="apparmor_parser" [ 14.278088] type=1400 audit(1331988037.873:4): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=710 comm="apparmor_parser" [ 14.278344] type=1400 audit(1331988037.873:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=780 comm="apparmor_parser" [ 14.278364] type=1400 audit(1331988037.873:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=782 comm="apparmor_parser" [ 14.278379] type=1400 audit(1331988037.873:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=710 comm="apparmor_parser" [ 14.278528] type=1400 audit(1331988037.873:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=780 comm="apparmor_parser" [ 14.278548] type=1400 audit(1331988037.873:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=782 comm="apparmor_parser" [ 14.278566] type=1400 audit(1331988037.873:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=710 comm="apparmor_parser" [ 14.476297] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule: [ 14.476300] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 14.476302] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule: [ 14.476304] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 14.476305] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule: [ 14.476307] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 14.476308] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule: [ 14.476310] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 14.476311] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule: [ 14.476313] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 14.476314] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule: [ 14.476315] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 14.476317] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule: [ 14.476318] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 14.476320] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule: [ 14.476321] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 14.476322] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule: [ 14.476324] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 14.476325] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule: [ 14.476327] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 14.476328] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule: [ 14.476330] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 14.476331] cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule: [ 14.476332] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 14.476334] cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule: [ 14.476335] cfg80211: 2402000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 14.476336] cfg80211: Disabling freq 2484 MHz [ 14.476412] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' [ 14.476806] Registered led device: rt2800usb-phy1::radio [ 14.476819] Registered led device: rt2800usb-phy1::assoc [ 14.476828] Registered led device: rt2800usb-phy1::quality [ 14.477713] usbcore: registered new interface driver rt2800usb [ 17.087363] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 18.474731] wlan0: authenticate with 00:1c:28:aa:09:d7 (try 1) [ 18.499143] wlan0: authenticated [ 18.505835] wlan0: associate with 00:1c:28:aa:09:d7 (try 1) [ 18.529725] wlan0: RX AssocResp from 00:1c:28:aa:09:d7 (capab=0x431 status=0 aid=1) [ 18.529734] wlan0: associated [ 18.531466] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 19.368884] type=1400 audit(1331988042.965:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=978 comm="apparmor_parser" [ 19.369229] type=1400 audit(1331988042.965:12): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=978 comm="apparmor_parser" [ 20.805925] r8169 0000:02:00.0: eth0: link down [ 20.807345] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 21.073525] ADDRCONF(NETDEV_UP): wlan1: link is not ready [ 21.886536] init: failsafe main process (870) killed by TERM signal [ 22.197711] type=1400 audit(1331988045.793:13): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1087 comm="apparmor_parser" [ 22.197985] type=1400 audit(1331988045.793:14): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1087 comm="apparmor_parser" [ 22.198162] type=1400 audit(1331988045.793:15): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1087 comm="apparmor_parser" [ 22.198203] type=1400 audit(1331988045.793:16): apparmor="STATUS" operation="profile_replace" name="/usr/lib/cups/backend/cups-pdf" pid=1091 comm="apparmor_parser" [ 22.198582] type=1400 audit(1331988045.793:17): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/cupsd" pid=1091 comm="apparmor_parser" [ 22.222145] type=1400 audit(1331988045.817:18): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm-guest-session-wrapper" pid=1086 comm="apparmor_parser" [ 22.315060] type=1400 audit(1331988045.909:19): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1090 comm="apparmor_parser" [ 22.315355] type=1400 audit(1331988045.909:20): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1090 comm="apparmor_parser"