[    7.260148] init: mongodb main process (1087) terminated with status 100
[    7.300180] e1000e 0000:00:19.0: irq 48 for MSI/MSI-X
[    7.355980] e1000e 0000:00:19.0: irq 48 for MSI/MSI-X
[    7.356429] ADDRCONF(NETDEV_UP): eth0: link is not ready
[    7.356738] ADDRCONF(NETDEV_UP): eth0: link is not ready
[    7.358769] iwlwifi 0000:03:00.0: L1 Enabled; Disabling L0S
[    7.358962] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[    7.362546] Bridge firewalling registered
[    7.376325] psmouse serio1: synaptics: Touchpad model: 1, fw: 8.0, id: 0x1e2b1, caps: 0xd001a3/0x940300/0x120c00
[    7.376331] psmouse serio1: synaptics: serio: Synaptics pass-through port at isa0060/serio1/input0
[    7.443337] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input10
[    7.494786] Adding 1999868k swap on /dev/mapper/cryptswap1.  Priority:-1 extents:1 across:1999868k SS
[    7.656458] iwlwifi 0000:03:00.0: L1 Enabled; Disabling L0S
[    7.656649] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[    7.774304] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[    7.775436] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[    7.779745] ip_tables: (C) 2000-2006 Netfilter Core Team
[    7.784624] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[    8.026025] init: anacron main process (1092) killed by TERM signal
[    8.129690] init: plymouth-stop pre-start process (1697) terminated with status 1
[    8.956721] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx
[    8.956725] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[    8.957249] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   13.718524] IBM TrackPoint firmware: 0x0e, buttons: 3/3
[   13.961594] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/serio2/input/input11
[   15.345386] wlan0: authenticate with 00:1e:2a:74:60:0a (try 1)
[   15.348270] wlan0: authenticated
[   15.387878] wlan0: associate with 00:1e:2a:74:60:0a (try 1)
[   15.391967] wlan0: RX AssocResp from 00:1e:2a:74:60:0a (capab=0x411 status=0 aid=3)
[   15.391978] wlan0: associated
[   15.395871] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   18.006231] lxcbr0: no IPv6 routers present
[   19.843635] eth0: no IPv6 routers present
[   26.048535] wlan0: no IPv6 routers present