[ 37.142564] Registered led device: phy0-led [ 37.142598] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 37.217418] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 37.320884] udevd[2738]: renamed network interface wlan0 to wlan1 [ 37.371849] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 37.371853] Bluetooth: BNEP filters: protocol multicast [ 37.377399] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 37.377404] cfg80211: World regulatory domain updated: [ 37.377406] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 37.377410] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 37.377413] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 37.377415] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 37.377418] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 37.377421] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 37.379437] Bluetooth: RFCOMM TTY layer initialized [ 37.379443] Bluetooth: RFCOMM socket layer initialized [ 37.379445] Bluetooth: RFCOMM ver 1.11 [ 37.572542] ADDRCONF(NETDEV_UP): wlan1: link is not ready [ 37.679737] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 37.679823] HDA Intel 0000:00:1b.0: irq 47 for MSI/MSI-X [ 37.679857] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 37.979583] input: HDA Intel Mic at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input16 [ 37.980245] input: HDA Intel Line Out at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input17 [ 37.980513] input: HDA Intel HP Out at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input18 [ 39.052564] lp: driver loaded but no devices found [ 39.098962] ppdev: user-space parallel port driver [ 39.176874] r8169 0000:02:00.0: eth1: link up [ 39.177877] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 49.456043] eth1: no IPv6 routers present [ 50.781027] ata6.00: failed to read SCR 1 (Emask=0x40) [ 50.781032] ata6.01: failed to read SCR 1 (Emask=0x40) [ 50.781038] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 50.781042] ata6.15: irq_stat 0x08000000, interface fatal error [ 50.781046] ata6.15: SError: { LinkSeq } [ 50.781049] ata6.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 50.781053] ata6.00: failed command: IDENTIFY DEVICE [ 50.781059] ata6.00: cmd ec/00:01:00:00:00/00:00:00:00:00/40 tag 0 pio 512 in [ 50.781060] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 50.781063] ata6.00: status: { DRDY } [ 50.781066] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 50.781071] ata6.15: hard resetting link [ 51.276060] ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 51.276597] ata6.00: hard resetting link [ 51.772271] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 320) [ 51.772302] ata6.01: hard resetting link [ 52.092390] ata6.01: SATA link down (SStatus 0 SControl 320) [ 52.092694] ata6.00: configured for UDMA/133 [ 52.140145] ata6: EH complete [ 52.184558] ata6.00: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xf [ 52.184564] ata6.00: SError: { CommWake DevExch } [ 52.184610] ata6.00: hard resetting link [ 52.577050] CPU0: Core temperature above threshold, cpu clock throttled (total events = 1) [ 52.577695] CPU0: Core temperature/speed normal [ 53.080423] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 320) [ 53.080848] ata6.00: configured for UDMA/133 [ 53.096204] ata6: EH complete [ 136.007486] ata6.00: failed to read SCR 1 (Emask=0x40) [ 136.007494] ata6.01: failed to read SCR 1 (Emask=0x40) [ 136.007502] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 136.007508] ata6.15: irq_stat 0x08000000, interface fatal error [ 136.007514] ata6.15: SError: { LinkSeq } [ 136.007520] ata6.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 136.007526] ata6.00: failed command: IDENTIFY DEVICE [ 136.007535] ata6.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [ 136.007537] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 136.007542] ata6.00: status: { DRDY } [ 136.007547] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 136.007555] ata6.15: hard resetting link [ 136.496103] ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 136.496906] ata6.00: hard resetting link [ 136.984222] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 320) [ 136.984247] ata6.01: hard resetting link [ 137.304379] ata6.01: SATA link down (SStatus 0 SControl 320) [ 137.304792] ata6.00: configured for UDMA/133 [ 137.352140] ata6: EH complete [ 137.352233] ata6.00: failed to read SCR 1 (Emask=0x40) [ 137.352239] ata6.01: failed to read SCR 1 (Emask=0x40) [ 137.352245] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 137.352250] ata6.15: irq_stat 0x08000000, interface fatal error [ 137.352254] ata6.15: SError: { LinkSeq } [ 137.352258] ata6.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 137.352262] ata6.00: failed command: CHECK POWER MODE [ 137.352269] ata6.00: cmd e5/00:00:00:00:00/00:00:00:00:00/00 tag 0 [ 137.352270] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 137.352274] ata6.00: status: { DRDY } [ 137.352278] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 137.352284] ata6.15: hard resetting link [ 137.896110] ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 137.896705] ata6.00: hard resetting link [ 138.412309] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 320) [ 138.412336] ata6.01: hard resetting link [ 138.736405] ata6.01: SATA link down (SStatus 0 SControl 320) [ 138.736730] ata6.00: configured for UDMA/133 [ 138.784095] ata6: EH complete [ 299.816149] [Hardware Error]: Machine check events logged [ 618.202899] ata6.00: failed to read SCR 1 (Emask=0x40) [ 618.202910] ata6.01: failed to read SCR 1 (Emask=0x40) [ 618.202922] ata6.15: limiting SATA link speed to 1.5 Gbps [ 618.202931] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 618.202940] ata6.15: irq_stat 0x08000000, interface fatal error [ 618.202948] ata6.15: SError: { LinkSeq } [ 618.202957] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 618.202966] ata6.00: failed command: READ FPDMA QUEUED [ 618.202981] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 618.202984] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 618.202991] ata6.00: status: { DRDY } [ 618.202999] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 618.203011] ata6.15: hard resetting link [ 618.696163] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 618.696832] ata6.00: hard resetting link [ 619.188451] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 619.188502] ata6.01: hard resetting link [ 619.508679] ata6.01: SATA link down (SStatus 0 SControl 310) [ 619.509108] ata6.00: configured for UDMA/133 [ 619.556168] ata6: EH complete [ 619.556231] ata6.00: failed to read SCR 1 (Emask=0x40) [ 619.556237] ata6.01: failed to read SCR 1 (Emask=0x40) [ 619.556246] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 619.556252] ata6.15: irq_stat 0x08000000, interface fatal error [ 619.556257] ata6.15: SError: { LinkSeq } [ 619.556274] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 619.556277] ata6.00: failed command: READ FPDMA QUEUED [ 619.556283] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 619.556285] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 619.556288] ata6.00: status: { DRDY } [ 619.556291] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 619.556295] ata6.15: hard resetting link [ 620.048086] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 620.048724] ata6.00: hard resetting link [ 620.540573] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 620.540615] ata6.01: hard resetting link [ 620.860674] ata6.01: SATA link down (SStatus 0 SControl 310) [ 620.861118] ata6.00: configured for UDMA/133 [ 620.908260] ata6: EH complete [ 620.908376] ata6.00: failed to read SCR 1 (Emask=0x40) [ 620.908382] ata6.01: failed to read SCR 1 (Emask=0x40) [ 620.908391] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 620.908406] ata6.15: irq_stat 0x08000000, interface fatal error [ 620.908409] ata6.15: SError: { LinkSeq } [ 620.908413] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 620.908416] ata6.00: failed command: READ FPDMA QUEUED [ 620.908422] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 620.908423] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 620.908427] ata6.00: status: { DRDY } [ 620.908430] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 620.908435] ata6.15: hard resetting link [ 621.400071] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 621.400712] ata6.01: limiting SATA link speed to 1.5 Gbps [ 621.400719] ata6.00: hard resetting link [ 621.892339] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 621.892389] ata6.01: hard resetting link [ 622.212494] ata6.01: SATA link down (SStatus 0 SControl 310) [ 622.212848] ata6.00: configured for UDMA/133 [ 622.260178] ata6: EH complete [ 622.260239] ata6.00: failed to read SCR 1 (Emask=0x40) [ 622.260245] ata6.01: failed to read SCR 1 (Emask=0x40) [ 622.260253] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 622.260259] ata6.15: irq_stat 0x08000000, interface fatal error [ 622.260274] ata6.15: SError: { LinkSeq } [ 622.260278] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 622.260281] ata6.00: failed command: READ FPDMA QUEUED [ 622.260287] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 622.260289] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 622.260292] ata6.00: status: { DRDY } [ 622.260295] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 622.260300] ata6.15: hard resetting link [ 622.752080] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 622.752721] ata6.01: limiting SATA link speed to 1.5 Gbps [ 622.752729] ata6.00: hard resetting link [ 623.244353] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 623.244393] ata6.01: hard resetting link [ 623.564539] ata6.01: SATA link down (SStatus 0 SControl 310) [ 623.564914] ata6.00: configured for UDMA/133 [ 623.612179] ata6: EH complete [ 623.612243] ata6.00: failed to read SCR 1 (Emask=0x40) [ 623.612247] ata6.01: failed to read SCR 1 (Emask=0x40) [ 623.612255] ata6.15: limiting speed to UDMA7:PIO5 [ 623.612259] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 623.612264] ata6.15: irq_stat 0x08000000, interface fatal error [ 623.612268] ata6.15: SError: { LinkSeq } [ 623.612272] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 623.612277] ata6.00: failed command: READ FPDMA QUEUED [ 623.612284] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 623.612285] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 623.612289] ata6.00: status: { DRDY } [ 623.612293] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 623.612299] ata6.15: hard resetting link [ 624.104081] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 624.104700] ata6.01: limiting SATA link speed to 1.5 Gbps [ 624.104707] ata6.00: hard resetting link [ 624.596364] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 624.596413] ata6.01: hard resetting link [ 624.916523] ata6.01: SATA link down (SStatus 0 SControl 310) [ 624.916899] ata6.00: configured for UDMA/133 [ 624.964217] ata6: EH complete [ 624.964306] ata6.00: failed to read SCR 1 (Emask=0x40) [ 624.964316] ata6.01: failed to read SCR 1 (Emask=0x40) [ 624.964328] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 624.964337] ata6.15: irq_stat 0x08000000, interface fatal error [ 624.964345] ata6.15: SError: { LinkSeq } [ 624.964354] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 624.964363] ata6.00: failed command: READ FPDMA QUEUED [ 624.964378] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 624.964381] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 624.964389] ata6.00: status: { DRDY } [ 624.964398] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 624.964409] ata6.15: hard resetting link [ 625.456054] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 625.456696] ata6.01: limiting SATA link speed to 1.5 Gbps [ 625.456704] ata6.00: hard resetting link [ 625.948367] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 625.948417] ata6.01: hard resetting link [ 626.268465] ata6.01: SATA link down (SStatus 0 SControl 310) [ 626.268766] ata6.00: configured for UDMA/133 [ 626.316130] sd 5:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 626.316135] sd 5:0:0:0: [sdb] Sense Key : Aborted Command [current] [descriptor] [ 626.316140] Descriptor sense data with sense descriptors (in hex): [ 626.316142] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 [ 626.316152] 00 00 00 00 [ 626.316156] sd 5:0:0:0: [sdb] Add. Sense: No additional sense information [ 626.316160] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 09 50 f8 00 00 00 08 00 [ 626.316170] end_request: I/O error, dev sdb, sector 156301312 [ 626.316174] Buffer I/O error on device sdb, logical block 19537664 [ 626.316190] ata6: EH complete [ 626.316269] ata6.00: failed to read SCR 1 (Emask=0x40) [ 626.316272] ata6.01: failed to read SCR 1 (Emask=0x40) [ 626.316278] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 626.316281] ata6.15: irq_stat 0x08000000, interface fatal error [ 626.316284] ata6.15: SError: { LinkSeq } [ 626.316288] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 626.316291] ata6.00: failed command: READ FPDMA QUEUED [ 626.316297] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 626.316298] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 626.316301] ata6.00: status: { DRDY } [ 626.316304] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 626.316309] ata6.15: hard resetting link [ 626.808079] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 626.808710] ata6.01: limiting SATA link speed to 1.5 Gbps [ 626.808718] ata6.00: hard resetting link [ 627.300391] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 627.300441] ata6.01: hard resetting link [ 627.620505] ata6.01: SATA link down (SStatus 0 SControl 310) [ 627.620880] ata6.00: configured for UDMA/133 [ 627.668179] ata6: EH complete [ 627.668227] ata6.00: failed to read SCR 1 (Emask=0x40) [ 627.668232] ata6.01: failed to read SCR 1 (Emask=0x40) [ 627.668239] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 627.668243] ata6.15: irq_stat 0x08000000, interface fatal error [ 627.668247] ata6.15: SError: { LinkSeq } [ 627.668251] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 627.668256] ata6.00: failed command: READ FPDMA QUEUED [ 627.668263] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 627.668265] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 627.668269] ata6.00: status: { DRDY } [ 627.668273] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 627.668278] ata6.15: hard resetting link [ 628.160057] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 628.160675] ata6.01: limiting SATA link speed to 1.5 Gbps [ 628.160682] ata6.00: hard resetting link [ 628.652534] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 628.652598] ata6.01: hard resetting link [ 628.972602] ata6.01: SATA link down (SStatus 0 SControl 310) [ 628.972962] ata6.00: configured for UDMA/133 [ 629.020322] ata6: EH complete [ 629.020423] ata6.00: failed to read SCR 1 (Emask=0x40) [ 629.020434] ata6.01: failed to read SCR 1 (Emask=0x40) [ 629.020446] ata6.15: limiting speed to PIO0 [ 629.020456] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 629.020464] ata6.15: irq_stat 0x08000000, interface fatal error [ 629.020473] ata6.15: SError: { LinkSeq } [ 629.020481] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 629.020490] ata6.00: failed command: READ FPDMA QUEUED [ 629.020505] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 629.020508] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 629.020516] ata6.00: status: { DRDY } [ 629.020524] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 629.020535] ata6.15: hard resetting link [ 629.512159] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 629.512869] ata6.01: limiting SATA link speed to 1.5 Gbps [ 629.512877] ata6.00: hard resetting link [ 630.004471] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 630.004518] ata6.01: hard resetting link [ 630.324633] ata6.01: SATA link down (SStatus 0 SControl 310) [ 630.325091] ata6.00: configured for UDMA/133 [ 630.372294] ata6: EH complete [ 630.372365] ata6.00: failed to read SCR 1 (Emask=0x40) [ 630.372375] ata6.01: failed to read SCR 1 (Emask=0x40) [ 630.372388] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 630.372397] ata6.15: irq_stat 0x08000000, interface fatal error [ 630.372405] ata6.15: SError: { LinkSeq } [ 630.372414] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 630.372423] ata6.00: failed command: READ FPDMA QUEUED [ 630.372448] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 630.372449] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 630.372452] ata6.00: status: { DRDY } [ 630.372455] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 630.372460] ata6.15: hard resetting link [ 630.864071] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 630.864835] ata6.01: limiting SATA link speed to 1.5 Gbps [ 630.864846] ata6.00: hard resetting link [ 631.356373] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 631.356423] ata6.01: hard resetting link [ 631.676647] ata6.01: SATA link down (SStatus 0 SControl 310) [ 631.677079] ata6.00: configured for UDMA/133 [ 631.724180] ata6: EH complete [ 631.724261] ata6.00: failed to read SCR 1 (Emask=0x40) [ 631.724271] ata6.01: failed to read SCR 1 (Emask=0x40) [ 631.724283] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 631.724291] ata6.15: irq_stat 0x08000000, interface fatal error [ 631.724300] ata6.15: SError: { LinkSeq } [ 631.724308] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 631.724317] ata6.00: failed command: READ FPDMA QUEUED [ 631.724332] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 631.724335] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 631.724342] ata6.00: status: { DRDY } [ 631.724351] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 631.724361] ata6.15: hard resetting link [ 632.216157] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 632.216819] ata6.01: limiting SATA link speed to 1.5 Gbps [ 632.216827] ata6.00: hard resetting link [ 632.708373] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 632.708423] ata6.01: hard resetting link [ 633.028609] ata6.01: SATA link down (SStatus 0 SControl 310) [ 633.029002] ata6.00: configured for UDMA/133 [ 633.076155] ata6: EH complete [ 633.076231] ata6.00: failed to read SCR 1 (Emask=0x40) [ 633.076236] ata6.01: failed to read SCR 1 (Emask=0x40) [ 633.076242] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 633.076247] ata6.15: irq_stat 0x08000000, interface fatal error [ 633.076251] ata6.15: SError: { LinkSeq } [ 633.076255] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 633.076260] ata6.00: failed command: READ FPDMA QUEUED [ 633.076267] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 633.076269] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 633.076273] ata6.00: status: { DRDY } [ 633.076277] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 633.076282] ata6.15: hard resetting link [ 633.568143] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 633.568836] ata6.01: limiting SATA link speed to 1.5 Gbps [ 633.568844] ata6.00: hard resetting link [ 634.060430] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 634.060492] ata6.01: hard resetting link [ 634.380604] ata6.01: SATA link down (SStatus 0 SControl 310) [ 634.380997] ata6.00: configured for UDMA/133 [ 634.428306] sd 5:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 634.428319] sd 5:0:0:0: [sdb] Sense Key : Aborted Command [current] [descriptor] [ 634.428331] Descriptor sense data with sense descriptors (in hex): [ 634.428337] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 [ 634.428361] 00 00 00 00 [ 634.428371] sd 5:0:0:0: [sdb] Add. Sense: No additional sense information [ 634.428381] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 09 50 f8 00 00 00 08 00 [ 634.428404] end_request: I/O error, dev sdb, sector 156301312 [ 634.428415] Buffer I/O error on device sdb, logical block 19537664 [ 634.428455] ata6: EH complete [ 634.428559] ata6.00: failed to read SCR 1 (Emask=0x40) [ 634.428562] ata6.01: failed to read SCR 1 (Emask=0x40) [ 634.428569] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 634.428572] ata6.15: irq_stat 0x08000000, interface fatal error [ 634.428575] ata6.15: SError: { LinkSeq } [ 634.428579] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 634.428582] ata6.00: failed command: READ FPDMA QUEUED [ 634.428588] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 634.428589] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 634.428592] ata6.00: status: { DRDY } [ 634.428596] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 634.428600] ata6.15: hard resetting link [ 634.920071] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 634.920723] ata6.01: limiting SATA link speed to 1.5 Gbps [ 634.920730] ata6.00: hard resetting link [ 635.412373] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 635.412423] ata6.01: hard resetting link [ 635.732606] ata6.01: SATA link down (SStatus 0 SControl 310) [ 635.732994] ata6.00: configured for UDMA/133 [ 635.780148] ata6: EH complete [ 635.780210] ata6.00: failed to read SCR 1 (Emask=0x40) [ 635.780217] ata6.01: failed to read SCR 1 (Emask=0x40) [ 635.780227] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 635.780233] ata6.15: irq_stat 0x08000000, interface fatal error [ 635.780238] ata6.15: SError: { LinkSeq } [ 635.780245] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 635.780250] ata6.00: failed command: READ FPDMA QUEUED [ 635.780260] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 635.780262] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 635.780276] ata6.00: status: { DRDY } [ 635.780279] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 635.780296] ata6.15: hard resetting link [ 636.272086] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 636.272723] ata6.01: limiting SATA link speed to 1.5 Gbps [ 636.272728] ata6.00: hard resetting link [ 636.764495] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 636.764526] ata6.01: hard resetting link [ 637.084548] ata6.01: SATA link down (SStatus 0 SControl 310) [ 637.084926] ata6.00: configured for UDMA/133 [ 637.132237] ata6: EH complete [ 637.132293] ata6.00: failed to read SCR 1 (Emask=0x40) [ 637.132299] ata6.01: failed to read SCR 1 (Emask=0x40) [ 637.132308] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 637.132314] ata6.15: irq_stat 0x08000000, interface fatal error [ 637.132320] ata6.15: SError: { LinkSeq } [ 637.132326] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 637.132332] ata6.00: failed command: READ FPDMA QUEUED [ 637.132350] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 637.132352] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 637.132355] ata6.00: status: { DRDY } [ 637.132358] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 637.132363] ata6.15: hard resetting link [ 637.624064] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 637.624721] ata6.01: limiting SATA link speed to 1.5 Gbps [ 637.624729] ata6.00: hard resetting link [ 638.116411] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 638.116474] ata6.01: hard resetting link [ 638.436647] ata6.01: SATA link down (SStatus 0 SControl 310) [ 638.437018] ata6.00: configured for UDMA/133 [ 638.484232] ata6: EH complete [ 638.484310] ata6.00: failed to read SCR 1 (Emask=0x40) [ 638.484320] ata6.01: failed to read SCR 1 (Emask=0x40) [ 638.484335] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 638.484344] ata6.15: irq_stat 0x08000000, interface fatal error [ 638.484352] ata6.15: SError: { LinkSeq } [ 638.484361] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 638.484370] ata6.00: failed command: READ FPDMA QUEUED [ 638.484389] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 638.484390] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 638.484393] ata6.00: status: { DRDY } [ 638.484396] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 638.484401] ata6.15: hard resetting link [ 638.976100] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 638.976856] ata6.01: limiting SATA link speed to 1.5 Gbps [ 638.976860] ata6.00: hard resetting link [ 639.468420] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 639.468470] ata6.01: hard resetting link [ 639.788540] ata6.01: SATA link down (SStatus 0 SControl 310) [ 639.788926] ata6.00: configured for UDMA/133 [ 639.836175] ata6: EH complete [ 639.836237] ata6.00: failed to read SCR 1 (Emask=0x40) [ 639.836243] ata6.01: failed to read SCR 1 (Emask=0x40) [ 639.836253] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 639.836259] ata6.15: irq_stat 0x08000000, interface fatal error [ 639.836265] ata6.15: SError: { LinkSeq } [ 639.836271] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 639.836276] ata6.00: failed command: READ FPDMA QUEUED [ 639.836286] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 639.836289] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 639.836294] ata6.00: status: { DRDY } [ 639.836299] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 639.836306] ata6.15: hard resetting link [ 640.328147] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 640.328882] ata6.01: limiting SATA link speed to 1.5 Gbps [ 640.328890] ata6.00: hard resetting link [ 640.820372] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 640.820422] ata6.01: hard resetting link [ 641.140817] ata6.01: SATA link down (SStatus 0 SControl 310) [ 641.141279] ata6.00: configured for UDMA/133 [ 641.188288] ata6: EH complete [ 641.188375] ata6.00: failed to read SCR 1 (Emask=0x40) [ 641.188385] ata6.01: failed to read SCR 1 (Emask=0x40) [ 641.188400] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 641.188408] ata6.15: irq_stat 0x08000000, interface fatal error [ 641.188416] ata6.15: SError: { LinkSeq } [ 641.188425] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 641.188434] ata6.00: failed command: READ FPDMA QUEUED [ 641.188449] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 641.188463] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 641.188466] ata6.00: status: { DRDY } [ 641.188469] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 641.188474] ata6.15: hard resetting link [ 641.680158] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 641.680825] ata6.01: limiting SATA link speed to 1.5 Gbps [ 641.680833] ata6.00: hard resetting link [ 642.172456] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 642.172494] ata6.01: hard resetting link [ 642.492728] ata6.01: SATA link down (SStatus 0 SControl 310) [ 642.493126] ata6.00: configured for UDMA/133 [ 642.540250] sd 5:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 642.540259] sd 5:0:0:0: [sdb] Sense Key : Aborted Command [current] [descriptor] [ 642.540267] Descriptor sense data with sense descriptors (in hex): [ 642.540270] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 [ 642.540286] 00 00 00 00 [ 642.540293] sd 5:0:0:0: [sdb] Add. Sense: No additional sense information [ 642.540300] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 09 50 f8 a0 00 00 08 00 [ 642.540315] end_request: I/O error, dev sdb, sector 156301472 [ 642.540322] Buffer I/O error on device sdb, logical block 19537684 [ 642.540353] ata6: EH complete [ 642.540441] ata6.00: failed to read SCR 1 (Emask=0x40) [ 642.540445] ata6.01: failed to read SCR 1 (Emask=0x40) [ 642.540452] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 642.540455] ata6.15: irq_stat 0x08000000, interface fatal error [ 642.540458] ata6.15: SError: { LinkSeq } [ 642.540462] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 642.540466] ata6.00: failed command: READ FPDMA QUEUED [ 642.540471] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 642.540473] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 642.540476] ata6.00: status: { DRDY } [ 642.540479] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 642.540484] ata6.15: hard resetting link [ 643.032134] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 643.032828] ata6.01: limiting SATA link speed to 1.5 Gbps [ 643.032836] ata6.00: hard resetting link [ 643.524338] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 643.524386] ata6.01: hard resetting link [ 643.844687] ata6.01: SATA link down (SStatus 0 SControl 310) [ 643.845085] ata6.00: configured for UDMA/133 [ 643.892251] ata6: EH complete [ 643.892313] ata6.00: failed to read SCR 1 (Emask=0x40) [ 643.892320] ata6.01: failed to read SCR 1 (Emask=0x40) [ 643.892329] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 643.892346] ata6.15: irq_stat 0x08000000, interface fatal error [ 643.892350] ata6.15: SError: { LinkSeq } [ 643.892353] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 643.892357] ata6.00: failed command: READ FPDMA QUEUED [ 643.892363] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 643.892364] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 643.892367] ata6.00: status: { DRDY } [ 643.892370] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 643.892375] ata6.15: hard resetting link [ 644.384159] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 644.384825] ata6.01: limiting SATA link speed to 1.5 Gbps [ 644.384833] ata6.00: hard resetting link [ 644.876519] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 644.876569] ata6.01: hard resetting link [ 645.196613] ata6.01: SATA link down (SStatus 0 SControl 310) [ 645.197005] ata6.00: configured for UDMA/133 [ 645.244342] ata6: EH complete [ 645.244431] ata6.00: failed to read SCR 1 (Emask=0x40) [ 645.244441] ata6.01: failed to read SCR 1 (Emask=0x40) [ 645.244455] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 645.244464] ata6.15: irq_stat 0x08000000, interface fatal error [ 645.244473] ata6.15: SError: { LinkSeq } [ 645.244482] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 645.244491] ata6.00: failed command: READ FPDMA QUEUED [ 645.244505] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 645.244509] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 645.244516] ata6.00: status: { DRDY } [ 645.244524] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 645.244535] ata6.15: hard resetting link [ 645.736162] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 645.736890] ata6.01: limiting SATA link speed to 1.5 Gbps [ 645.736898] ata6.00: hard resetting link [ 646.228419] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 646.228469] ata6.01: hard resetting link [ 646.548633] ata6.01: SATA link down (SStatus 0 SControl 310) [ 646.549008] ata6.00: configured for UDMA/133 [ 646.596328] ata6: EH complete [ 646.596416] ata6.00: failed to read SCR 1 (Emask=0x40) [ 646.596425] ata6.01: failed to read SCR 1 (Emask=0x40) [ 646.596439] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 646.596448] ata6.15: irq_stat 0x08000000, interface fatal error [ 646.596456] ata6.15: SError: { LinkSeq } [ 646.596465] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 646.596474] ata6.00: failed command: READ FPDMA QUEUED [ 646.596489] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 646.596492] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 646.596499] ata6.00: status: { DRDY } [ 646.596508] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 646.596519] ata6.15: hard resetting link [ 647.088151] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 647.088818] ata6.01: limiting SATA link speed to 1.5 Gbps [ 647.088826] ata6.00: hard resetting link [ 647.580443] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 647.580494] ata6.01: hard resetting link [ 647.900820] ata6.01: SATA link down (SStatus 0 SControl 310) [ 647.901282] ata6.00: configured for UDMA/133 [ 647.948331] ata6: EH complete [ 647.948426] ata6.00: failed to read SCR 1 (Emask=0x40) [ 647.948435] ata6.01: failed to read SCR 1 (Emask=0x40) [ 647.948450] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 647.948459] ata6.15: irq_stat 0x08000000, interface fatal error [ 647.948467] ata6.15: SError: { LinkSeq } [ 647.948476] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 647.948485] ata6.00: failed command: READ FPDMA QUEUED [ 647.948500] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 647.948503] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 647.948511] ata6.00: status: { DRDY } [ 647.948519] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 647.948530] ata6.15: hard resetting link [ 648.440109] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 648.440805] ata6.01: limiting SATA link speed to 1.5 Gbps [ 648.440812] ata6.00: hard resetting link [ 648.932434] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 648.932497] ata6.01: hard resetting link [ 649.252600] ata6.01: SATA link down (SStatus 0 SControl 310) [ 649.252986] ata6.00: configured for UDMA/133 [ 649.300307] ata6: EH complete [ 649.300487] ata6.00: failed to read SCR 1 (Emask=0x40) [ 649.300497] ata6.01: failed to read SCR 1 (Emask=0x40) [ 649.300511] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 649.300519] ata6.15: irq_stat 0x08000000, interface fatal error [ 649.300528] ata6.15: SError: { LinkSeq } [ 649.300537] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 649.300546] ata6.00: failed command: READ FPDMA QUEUED [ 649.300560] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 649.300563] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 649.300571] ata6.00: status: { DRDY } [ 649.300579] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 649.300591] ata6.15: hard resetting link [ 649.792052] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 649.792725] ata6.01: limiting SATA link speed to 1.5 Gbps [ 649.792732] ata6.00: hard resetting link [ 650.284378] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 650.284443] ata6.01: hard resetting link [ 650.604544] ata6.01: SATA link down (SStatus 0 SControl 310) [ 650.604980] ata6.00: configured for UDMA/133 [ 650.652142] sd 5:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 650.652159] sd 5:0:0:0: [sdb] Sense Key : Aborted Command [current] [descriptor] [ 650.652165] Descriptor sense data with sense descriptors (in hex): [ 650.652168] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 [ 650.652179] 00 00 00 00 [ 650.652185] sd 5:0:0:0: [sdb] Add. Sense: No additional sense information [ 650.652190] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 09 50 f8 a0 00 00 08 00 [ 650.652201] end_request: I/O error, dev sdb, sector 156301472 [ 650.652207] Buffer I/O error on device sdb, logical block 19537684 [ 650.652227] ata6: EH complete [ 650.721243] ata6.00: failed to read SCR 1 (Emask=0x40) [ 650.721254] ata6.01: failed to read SCR 1 (Emask=0x40) [ 650.721269] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 650.721278] ata6.15: irq_stat 0x08000000, interface fatal error [ 650.721286] ata6.15: SError: { LinkSeq } [ 650.721295] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 650.721304] ata6.00: failed command: READ FPDMA QUEUED [ 650.721318] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 650.721321] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 650.721329] ata6.00: status: { DRDY } [ 650.721337] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 650.721348] ata6.15: hard resetting link [ 651.212148] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 651.212811] ata6.01: limiting SATA link speed to 1.5 Gbps [ 651.212818] ata6.00: hard resetting link [ 651.704416] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 651.704466] ata6.01: hard resetting link [ 652.024525] ata6.01: SATA link down (SStatus 0 SControl 310) [ 652.024890] ata6.00: configured for UDMA/133 [ 652.072156] ata6: EH complete [ 652.072203] ata6.00: failed to read SCR 1 (Emask=0x40) [ 652.072207] ata6.01: failed to read SCR 1 (Emask=0x40) [ 652.072215] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 652.072220] ata6.15: irq_stat 0x08000000, interface fatal error [ 652.072224] ata6.15: SError: { LinkSeq } [ 652.072228] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 652.072233] ata6.00: failed command: READ FPDMA QUEUED [ 652.072240] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 652.072241] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 652.072245] ata6.00: status: { DRDY } [ 652.072249] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 652.072255] ata6.15: hard resetting link [ 652.564060] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 652.564745] ata6.01: limiting SATA link speed to 1.5 Gbps [ 652.564752] ata6.00: hard resetting link [ 653.056462] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 653.056512] ata6.01: hard resetting link [ 653.376623] ata6.01: SATA link down (SStatus 0 SControl 310) [ 653.377014] ata6.00: configured for UDMA/133 [ 653.424177] ata6: EH complete [ 653.424274] ata6.00: failed to read SCR 1 (Emask=0x40) [ 653.424280] ata6.01: failed to read SCR 1 (Emask=0x40) [ 653.424290] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 653.424296] ata6.15: irq_stat 0x08000000, interface fatal error [ 653.424301] ata6.15: SError: { LinkSeq } [ 653.424307] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 653.424313] ata6.00: failed command: READ FPDMA QUEUED [ 653.424322] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 653.424324] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 653.424330] ata6.00: status: { DRDY } [ 653.424335] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 653.424342] ata6.15: hard resetting link [ 653.916069] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 653.916649] ata6.01: limiting SATA link speed to 1.5 Gbps [ 653.916653] ata6.00: hard resetting link [ 654.408683] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 654.408732] ata6.01: hard resetting link [ 654.728526] ata6.01: SATA link down (SStatus 0 SControl 310) [ 654.728896] ata6.00: configured for UDMA/133 [ 654.776173] ata6: EH complete [ 654.776225] ata6.00: failed to read SCR 1 (Emask=0x40) [ 654.776230] ata6.01: failed to read SCR 1 (Emask=0x40) [ 654.776238] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 654.776242] ata6.15: irq_stat 0x08000000, interface fatal error [ 654.776247] ata6.15: SError: { LinkSeq } [ 654.776251] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 654.776256] ata6.00: failed command: READ FPDMA QUEUED [ 654.776263] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 654.776265] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 654.776269] ata6.00: status: { DRDY } [ 654.776273] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 654.776278] ata6.15: hard resetting link [ 655.268067] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 655.268712] ata6.01: limiting SATA link speed to 1.5 Gbps [ 655.268719] ata6.00: hard resetting link [ 655.760350] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 655.760400] ata6.01: hard resetting link [ 656.080282] ata6.01: SATA link down (SStatus 0 SControl 310) [ 656.080649] ata6.00: configured for UDMA/133 [ 656.132112] ata6: EH complete [ 656.132158] ata6.00: failed to read SCR 1 (Emask=0x40) [ 656.132162] ata6.01: failed to read SCR 1 (Emask=0x40) [ 656.132170] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 656.132174] ata6.15: irq_stat 0x08000000, interface fatal error [ 656.132177] ata6.15: SError: { LinkSeq } [ 656.132181] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 656.132185] ata6.00: failed command: READ FPDMA QUEUED [ 656.132191] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 656.132192] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 656.132195] ata6.00: status: { DRDY } [ 656.132198] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 656.132204] ata6.15: hard resetting link [ 656.628067] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 656.628649] ata6.01: limiting SATA link speed to 1.5 Gbps [ 656.628654] ata6.00: hard resetting link [ 657.120274] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 657.120305] ata6.01: hard resetting link [ 657.444311] ata6.01: SATA link down (SStatus 0 SControl 310) [ 657.444622] ata6.00: configured for UDMA/133 [ 657.492109] ata6: EH complete [ 657.492146] ata6.00: failed to read SCR 1 (Emask=0x40) [ 657.492151] ata6.01: failed to read SCR 1 (Emask=0x40) [ 657.492158] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 657.492162] ata6.15: irq_stat 0x08000000, interface fatal error [ 657.492165] ata6.15: SError: { LinkSeq } [ 657.492169] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 657.492173] ata6.00: failed command: READ FPDMA QUEUED [ 657.492179] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 657.492181] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 657.492184] ata6.00: status: { DRDY } [ 657.492187] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 657.492192] ata6.15: hard resetting link [ 657.984102] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 657.984731] ata6.01: limiting SATA link speed to 1.5 Gbps [ 657.984736] ata6.00: hard resetting link [ 658.480464] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 658.480514] ata6.01: hard resetting link [ 658.800624] ata6.01: SATA link down (SStatus 0 SControl 310) [ 658.801058] ata6.00: configured for UDMA/133 [ 658.848339] sd 5:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 658.848352] sd 5:0:0:0: [sdb] Sense Key : Aborted Command [current] [descriptor] [ 658.848364] Descriptor sense data with sense descriptors (in hex): [ 658.848369] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 [ 658.848393] 00 00 00 00 [ 658.848403] sd 5:0:0:0: [sdb] Add. Sense: No additional sense information [ 658.848414] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 09 50 f8 00 00 00 08 00 [ 658.848436] end_request: I/O error, dev sdb, sector 156301312 [ 658.848447] Buffer I/O error on device sdb, logical block 19537664 [ 658.848504] ata6: EH complete [ 658.848569] ata6.00: failed to read SCR 1 (Emask=0x40) [ 658.848574] ata6.01: failed to read SCR 1 (Emask=0x40) [ 658.848581] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 658.848584] ata6.15: irq_stat 0x08000000, interface fatal error [ 658.848587] ata6.15: SError: { LinkSeq } [ 658.848591] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 658.848595] ata6.00: failed command: READ FPDMA QUEUED [ 658.848601] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 658.848602] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 658.848605] ata6.00: status: { DRDY } [ 658.848608] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 658.848613] ata6.15: hard resetting link [ 659.348055] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 659.348613] ata6.01: limiting SATA link speed to 1.5 Gbps [ 659.348619] ata6.00: hard resetting link [ 659.840444] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 659.840494] ata6.01: hard resetting link [ 660.160648] ata6.01: SATA link down (SStatus 0 SControl 310) [ 660.161019] ata6.00: configured for UDMA/133 [ 660.208245] ata6: EH complete [ 660.208333] ata6.00: failed to read SCR 1 (Emask=0x40) [ 660.208342] ata6.01: failed to read SCR 1 (Emask=0x40) [ 660.208357] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 660.208366] ata6.15: irq_stat 0x08000000, interface fatal error [ 660.208374] ata6.15: SError: { LinkSeq } [ 660.208384] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 660.208393] ata6.00: failed command: READ FPDMA QUEUED [ 660.208408] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 660.208411] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 660.208419] ata6.00: status: { DRDY } [ 660.208427] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 660.208438] ata6.15: hard resetting link [ 660.700116] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 660.700787] ata6.01: limiting SATA link speed to 1.5 Gbps [ 660.700794] ata6.00: hard resetting link [ 661.192426] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 661.192474] ata6.01: hard resetting link [ 661.512692] ata6.01: SATA link down (SStatus 0 SControl 310) [ 661.513081] ata6.00: configured for UDMA/133 [ 661.560179] ata6: EH complete [ 661.560240] ata6.00: failed to read SCR 1 (Emask=0x40) [ 661.560249] ata6.01: failed to read SCR 1 (Emask=0x40) [ 661.560259] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 661.560265] ata6.15: irq_stat 0x08000000, interface fatal error [ 661.560271] ata6.15: SError: { LinkSeq } [ 661.560277] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 661.560283] ata6.00: failed command: READ FPDMA QUEUED [ 661.560293] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 661.560295] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 661.560300] ata6.00: status: { DRDY } [ 661.560305] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 661.560312] ata6.15: hard resetting link [ 662.052089] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 662.052759] ata6.01: limiting SATA link speed to 1.5 Gbps [ 662.052767] ata6.00: hard resetting link [ 662.544468] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 662.544520] ata6.01: hard resetting link [ 662.864574] ata6.01: SATA link down (SStatus 0 SControl 310) [ 662.864957] ata6.00: configured for UDMA/133 [ 662.912304] ata6: EH complete [ 662.912431] ata6.00: failed to read SCR 1 (Emask=0x40) [ 662.912441] ata6.01: failed to read SCR 1 (Emask=0x40) [ 662.912456] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 662.912464] ata6.15: irq_stat 0x08000000, interface fatal error [ 662.912479] ata6.15: SError: { LinkSeq } [ 662.912483] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 662.912486] ata6.00: failed command: READ FPDMA QUEUED [ 662.912492] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 662.912493] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 662.912496] ata6.00: status: { DRDY } [ 662.912500] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 662.912504] ata6.15: hard resetting link [ 663.404134] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 663.404826] ata6.01: limiting SATA link speed to 1.5 Gbps [ 663.404833] ata6.00: hard resetting link [ 663.896492] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 663.896555] ata6.01: hard resetting link [ 664.216549] ata6.01: SATA link down (SStatus 0 SControl 310) [ 664.216926] ata6.00: configured for UDMA/133 [ 664.264232] ata6: EH complete [ 664.264326] ata6.00: failed to read SCR 1 (Emask=0x40) [ 664.264333] ata6.01: failed to read SCR 1 (Emask=0x40) [ 664.264352] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 664.264356] ata6.15: irq_stat 0x08000000, interface fatal error [ 664.264359] ata6.15: SError: { LinkSeq } [ 664.264363] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 664.264367] ata6.00: failed command: READ FPDMA QUEUED [ 664.264372] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 664.264374] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 664.264377] ata6.00: status: { DRDY } [ 664.264380] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 664.264385] ata6.15: hard resetting link [ 664.756068] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 664.756745] ata6.01: limiting SATA link speed to 1.5 Gbps [ 664.756752] ata6.00: hard resetting link [ 665.248494] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 665.248557] ata6.01: hard resetting link [ 665.568623] ata6.01: SATA link down (SStatus 0 SControl 310) [ 665.569010] ata6.00: configured for UDMA/133 [ 665.616240] ata6: EH complete [ 665.616363] ata6.00: failed to read SCR 1 (Emask=0x40) [ 665.616370] ata6.01: failed to read SCR 1 (Emask=0x40) [ 665.616380] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 665.616386] ata6.15: irq_stat 0x08000000, interface fatal error [ 665.616392] ata6.15: SError: { LinkSeq } [ 665.616398] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 665.616403] ata6.00: failed command: READ FPDMA QUEUED [ 665.616413] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 665.616415] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 665.616420] ata6.00: status: { DRDY } [ 665.616426] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 665.616433] ata6.15: hard resetting link [ 666.108119] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 666.108775] ata6.01: limiting SATA link speed to 1.5 Gbps [ 666.108781] ata6.00: hard resetting link [ 666.600356] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 666.600405] ata6.01: hard resetting link [ 666.920693] ata6.01: SATA link down (SStatus 0 SControl 310) [ 666.921154] ata6.00: configured for UDMA/133 [ 666.968140] sd 5:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 666.968146] sd 5:0:0:0: [sdb] Sense Key : Aborted Command [current] [descriptor] [ 666.968151] Descriptor sense data with sense descriptors (in hex): [ 666.968153] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 [ 666.968163] 00 00 00 00 [ 666.968167] sd 5:0:0:0: [sdb] Add. Sense: No additional sense information [ 666.968171] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 09 50 f8 00 00 00 08 00 [ 666.968181] end_request: I/O error, dev sdb, sector 156301312 [ 666.968186] Buffer I/O error on device sdb, logical block 19537664 [ 666.968207] ata6: EH complete [ 666.968281] ata6.00: failed to read SCR 1 (Emask=0x40) [ 666.968285] ata6.01: failed to read SCR 1 (Emask=0x40) [ 666.968293] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 666.968296] ata6.15: irq_stat 0x08000000, interface fatal error [ 666.968299] ata6.15: SError: { LinkSeq } [ 666.968303] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 666.968307] ata6.00: failed command: READ FPDMA QUEUED [ 666.968313] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 666.968314] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 666.968317] ata6.00: status: { DRDY } [ 666.968320] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 666.968325] ata6.15: hard resetting link [ 667.460057] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 667.460690] ata6.01: limiting SATA link speed to 1.5 Gbps [ 667.460696] ata6.00: hard resetting link [ 667.952410] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 667.952473] ata6.01: hard resetting link [ 668.272497] ata6.01: SATA link down (SStatus 0 SControl 310) [ 668.272804] ata6.00: configured for UDMA/133 [ 668.320232] ata6: EH complete [ 668.320308] ata6.00: failed to read SCR 1 (Emask=0x40) [ 668.320313] ata6.01: failed to read SCR 1 (Emask=0x40) [ 668.320321] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 668.320326] ata6.15: irq_stat 0x08000000, interface fatal error [ 668.320330] ata6.15: SError: { LinkSeq } [ 668.320334] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 668.320339] ata6.00: failed command: READ FPDMA QUEUED [ 668.320346] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 668.320348] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 668.320352] ata6.00: status: { DRDY } [ 668.320356] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 668.320361] ata6.15: hard resetting link [ 668.812149] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 668.812852] ata6.01: limiting SATA link speed to 1.5 Gbps [ 668.812864] ata6.00: hard resetting link [ 669.304419] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 669.304462] ata6.01: hard resetting link [ 669.624602] ata6.01: SATA link down (SStatus 0 SControl 310) [ 669.624981] ata6.00: configured for UDMA/133 [ 669.672127] ata6: EH complete [ 669.672180] ata6.00: failed to read SCR 1 (Emask=0x40) [ 669.672184] ata6.01: failed to read SCR 1 (Emask=0x40) [ 669.672193] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 669.672197] ata6.15: irq_stat 0x08000000, interface fatal error [ 669.672201] ata6.15: SError: { LinkSeq } [ 669.672206] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 669.672211] ata6.00: failed command: READ FPDMA QUEUED [ 669.672218] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 669.672219] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 669.672223] ata6.00: status: { DRDY } [ 669.672227] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 669.672232] ata6.15: hard resetting link [ 670.164054] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 670.164655] ata6.01: limiting SATA link speed to 1.5 Gbps [ 670.164663] ata6.00: hard resetting link [ 670.656508] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 670.656573] ata6.01: hard resetting link [ 670.976754] ata6.01: SATA link down (SStatus 0 SControl 310) [ 670.977267] ata6.00: configured for UDMA/133 [ 671.024181] ata6: EH complete [ 671.024266] ata6.00: failed to read SCR 1 (Emask=0x40) [ 671.024275] ata6.01: failed to read SCR 1 (Emask=0x40) [ 671.024291] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 671.024300] ata6.15: irq_stat 0x08000000, interface fatal error [ 671.024307] ata6.15: SError: { LinkSeq } [ 671.024316] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 671.024325] ata6.00: failed command: READ FPDMA QUEUED [ 671.024339] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 671.024342] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 671.024350] ata6.00: status: { DRDY } [ 671.024358] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 671.024369] ata6.15: hard resetting link [ 671.516055] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 671.516746] ata6.01: limiting SATA link speed to 1.5 Gbps [ 671.516754] ata6.00: hard resetting link [ 672.008652] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 672.008717] ata6.01: hard resetting link [ 672.328657] ata6.01: SATA link down (SStatus 0 SControl 310) [ 672.329027] ata6.00: configured for UDMA/133 [ 672.376242] ata6: EH complete [ 672.376311] ata6.00: failed to read SCR 1 (Emask=0x40) [ 672.376316] ata6.01: failed to read SCR 1 (Emask=0x40) [ 672.376324] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 672.376329] ata6.15: irq_stat 0x08000000, interface fatal error [ 672.376333] ata6.15: SError: { LinkSeq } [ 672.376338] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 672.376342] ata6.00: failed command: READ FPDMA QUEUED [ 672.376350] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 672.376351] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 672.376355] ata6.00: status: { DRDY } [ 672.376359] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 672.376364] ata6.15: hard resetting link [ 672.868139] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 672.868826] ata6.01: limiting SATA link speed to 1.5 Gbps [ 672.868834] ata6.00: hard resetting link [ 673.360365] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 673.360406] ata6.01: hard resetting link [ 673.680549] ata6.01: SATA link down (SStatus 0 SControl 310) [ 673.680977] ata6.00: configured for UDMA/133 [ 673.728291] ata6: EH complete [ 673.728378] ata6.00: failed to read SCR 1 (Emask=0x40) [ 673.728388] ata6.01: failed to read SCR 1 (Emask=0x40) [ 673.728403] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 673.728412] ata6.15: irq_stat 0x08000000, interface fatal error [ 673.728420] ata6.15: SError: { LinkSeq } [ 673.728428] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 673.728437] ata6.00: failed command: READ FPDMA QUEUED [ 673.728452] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 673.728455] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 673.728463] ata6.00: status: { DRDY } [ 673.728471] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 673.728482] ata6.15: hard resetting link [ 674.220139] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 674.220756] ata6.01: limiting SATA link speed to 1.5 Gbps [ 674.220764] ata6.00: hard resetting link [ 674.712481] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 674.712544] ata6.01: hard resetting link [ 675.032751] ata6.01: SATA link down (SStatus 0 SControl 310) [ 675.033222] ata6.00: configured for UDMA/133 [ 675.080262] sd 5:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 675.080274] sd 5:0:0:0: [sdb] Sense Key : Aborted Command [current] [descriptor] [ 675.080286] Descriptor sense data with sense descriptors (in hex): [ 675.080291] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 [ 675.080315] 00 00 00 00 [ 675.080325] sd 5:0:0:0: [sdb] Add. Sense: No additional sense information [ 675.080335] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 09 50 f8 a0 00 00 08 00 [ 675.080358] end_request: I/O error, dev sdb, sector 156301472 [ 675.080369] Buffer I/O error on device sdb, logical block 19537684 [ 675.080412] ata6: EH complete [ 675.080528] ata6.00: failed to read SCR 1 (Emask=0x40) [ 675.080537] ata6.01: failed to read SCR 1 (Emask=0x40) [ 675.080554] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 675.080561] ata6.15: irq_stat 0x08000000, interface fatal error [ 675.080569] ata6.15: SError: { LinkSeq } [ 675.080578] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 675.080587] ata6.00: failed command: READ FPDMA QUEUED [ 675.080601] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 675.080604] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 675.080612] ata6.00: status: { DRDY } [ 675.080620] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 675.080630] ata6.15: hard resetting link [ 675.572105] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 675.572710] ata6.01: limiting SATA link speed to 1.5 Gbps [ 675.572715] ata6.00: hard resetting link [ 676.064337] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 676.064379] ata6.01: hard resetting link [ 676.384632] ata6.01: SATA link down (SStatus 0 SControl 310) [ 676.384997] ata6.00: configured for UDMA/133 [ 676.432242] ata6: EH complete [ 676.432293] ata6.00: failed to read SCR 1 (Emask=0x40) [ 676.432298] ata6.01: failed to read SCR 1 (Emask=0x40) [ 676.432307] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 676.432311] ata6.15: irq_stat 0x08000000, interface fatal error [ 676.432315] ata6.15: SError: { LinkSeq } [ 676.432320] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 676.432324] ata6.00: failed command: READ FPDMA QUEUED [ 676.432332] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 676.432333] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 676.432337] ata6.00: status: { DRDY } [ 676.432341] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 676.432346] ata6.15: hard resetting link [ 676.924136] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 676.924808] ata6.01: limiting SATA link speed to 1.5 Gbps [ 676.924815] ata6.00: hard resetting link [ 677.416402] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 677.416452] ata6.01: hard resetting link [ 677.744591] ata6.01: SATA link down (SStatus 0 SControl 310) [ 677.744903] ata6.00: configured for UDMA/133 [ 677.792130] ata6: EH complete [ 677.792178] ata6.00: failed to read SCR 1 (Emask=0x40) [ 677.792181] ata6.01: failed to read SCR 1 (Emask=0x40) [ 677.792189] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 677.792192] ata6.15: irq_stat 0x08000000, interface fatal error [ 677.792195] ata6.15: SError: { LinkSeq } [ 677.792199] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 677.792203] ata6.00: failed command: READ FPDMA QUEUED [ 677.792209] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 677.792210] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 677.792213] ata6.00: status: { DRDY } [ 677.792216] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 677.792221] ata6.15: hard resetting link [ 678.284126] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 678.284779] ata6.01: limiting SATA link speed to 1.5 Gbps [ 678.284785] ata6.00: hard resetting link [ 678.776372] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 678.776431] ata6.01: hard resetting link [ 679.096590] ata6.01: SATA link down (SStatus 0 SControl 310) [ 679.096980] ata6.00: configured for UDMA/133 [ 679.144232] ata6: EH complete [ 679.144284] ata6.00: failed to read SCR 1 (Emask=0x40) [ 679.144289] ata6.01: failed to read SCR 1 (Emask=0x40) [ 679.144298] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 679.144302] ata6.15: irq_stat 0x08000000, interface fatal error [ 679.144306] ata6.15: SError: { LinkSeq } [ 679.144311] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 679.144315] ata6.00: failed command: READ FPDMA QUEUED [ 679.144323] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 679.144324] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 679.144328] ata6.00: status: { DRDY } [ 679.144332] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 679.144338] ata6.15: hard resetting link [ 679.636058] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 679.636629] ata6.01: limiting SATA link speed to 1.5 Gbps [ 679.636633] ata6.00: hard resetting link [ 680.132502] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 680.132574] ata6.01: hard resetting link [ 680.452547] ata6.01: SATA link down (SStatus 0 SControl 310) [ 680.452925] ata6.00: configured for UDMA/133 [ 680.500235] ata6: EH complete [ 680.500299] ata6.00: failed to read SCR 1 (Emask=0x40) [ 680.500306] ata6.01: failed to read SCR 1 (Emask=0x40) [ 680.500317] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 680.500323] ata6.15: irq_stat 0x08000000, interface fatal error [ 680.500328] ata6.15: SError: { LinkSeq } [ 680.500334] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 680.500349] ata6.00: failed command: READ FPDMA QUEUED [ 680.500355] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 680.500367] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 680.500375] ata6.00: status: { DRDY } [ 680.500383] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 680.500394] ata6.15: hard resetting link [ 680.992159] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 680.992830] ata6.01: limiting SATA link speed to 1.5 Gbps [ 680.992838] ata6.00: hard resetting link [ 681.484441] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 681.484491] ata6.01: hard resetting link [ 681.808317] ata6.01: SATA link down (SStatus 0 SControl 310) [ 681.808623] ata6.00: configured for UDMA/133 [ 681.856101] ata6: EH complete [ 681.856147] ata6.00: failed to read SCR 1 (Emask=0x40) [ 681.856151] ata6.01: failed to read SCR 1 (Emask=0x40) [ 681.856159] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 681.856162] ata6.15: irq_stat 0x08000000, interface fatal error [ 681.856166] ata6.15: SError: { LinkSeq } [ 681.856169] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 681.856173] ata6.00: failed command: READ FPDMA QUEUED [ 681.856179] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 681.856180] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 681.856183] ata6.00: status: { DRDY } [ 681.856187] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 681.856191] ata6.15: hard resetting link [ 682.348066] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 682.348651] ata6.01: limiting SATA link speed to 1.5 Gbps [ 682.348656] ata6.00: hard resetting link [ 682.840213] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 682.840263] ata6.01: hard resetting link [ 683.160595] ata6.01: SATA link down (SStatus 0 SControl 310) [ 683.160992] ata6.00: configured for UDMA/133 [ 683.208215] sd 5:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 683.208223] sd 5:0:0:0: [sdb] Sense Key : Aborted Command [current] [descriptor] [ 683.208231] Descriptor sense data with sense descriptors (in hex): [ 683.208235] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 [ 683.208251] 00 00 00 00 [ 683.208258] sd 5:0:0:0: [sdb] Add. Sense: No additional sense information [ 683.208265] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 09 50 f8 a0 00 00 08 00 [ 683.208280] end_request: I/O error, dev sdb, sector 156301472 [ 683.208287] Buffer I/O error on device sdb, logical block 19537684 [ 683.208313] ata6: EH complete [ 683.269148] ata6.00: failed to read SCR 1 (Emask=0x40) [ 683.269159] ata6.01: failed to read SCR 1 (Emask=0x40) [ 683.269175] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 683.269183] ata6.15: irq_stat 0x08000000, interface fatal error [ 683.269191] ata6.15: SError: { LinkSeq } [ 683.269200] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 683.269209] ata6.00: failed command: READ FPDMA QUEUED [ 683.269223] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 683.269226] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 683.269234] ata6.00: status: { DRDY } [ 683.269242] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 683.269253] ata6.15: hard resetting link [ 683.760112] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 683.760764] ata6.01: limiting SATA link speed to 1.5 Gbps [ 683.760772] ata6.00: hard resetting link [ 684.252373] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 684.252423] ata6.01: hard resetting link [ 684.572564] ata6.01: SATA link down (SStatus 0 SControl 310) [ 684.572883] ata6.00: configured for UDMA/133 [ 684.620144] ata6: EH complete [ 684.620218] ata6.00: failed to read SCR 1 (Emask=0x40) [ 684.620224] ata6.01: failed to read SCR 1 (Emask=0x40) [ 684.620234] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 684.620240] ata6.15: irq_stat 0x08000000, interface fatal error [ 684.620246] ata6.15: SError: { LinkSeq } [ 684.620252] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 684.620258] ata6.00: failed command: READ FPDMA QUEUED [ 684.620276] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 684.620278] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 684.620281] ata6.00: status: { DRDY } [ 684.620284] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 684.620288] ata6.15: hard resetting link [ 685.112067] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 685.112752] ata6.01: limiting SATA link speed to 1.5 Gbps [ 685.112760] ata6.00: hard resetting link [ 685.604426] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 685.604476] ata6.01: hard resetting link [ 685.924571] ata6.01: SATA link down (SStatus 0 SControl 310) [ 685.924957] ata6.00: configured for UDMA/133 [ 685.972207] ata6: EH complete [ 685.972288] ata6.00: failed to read SCR 1 (Emask=0x40) [ 685.972294] ata6.01: failed to read SCR 1 (Emask=0x40) [ 685.972305] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 685.972311] ata6.15: irq_stat 0x08000000, interface fatal error [ 685.972316] ata6.15: SError: { LinkSeq } [ 685.972322] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 685.972338] ata6.00: failed command: READ FPDMA QUEUED [ 685.972344] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 685.972345] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 685.972348] ata6.00: status: { DRDY } [ 685.972351] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 685.972356] ata6.15: hard resetting link [ 686.464070] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 686.464733] ata6.01: limiting SATA link speed to 1.5 Gbps [ 686.464740] ata6.00: hard resetting link [ 686.960420] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 686.960462] ata6.01: hard resetting link [ 687.280606] ata6.01: SATA link down (SStatus 0 SControl 310) [ 687.280999] ata6.00: configured for UDMA/133 [ 687.328233] ata6: EH complete [ 687.328304] ata6.00: failed to read SCR 1 (Emask=0x40) [ 687.328308] ata6.01: failed to read SCR 1 (Emask=0x40) [ 687.328317] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 687.328321] ata6.15: irq_stat 0x08000000, interface fatal error [ 687.328325] ata6.15: SError: { LinkSeq } [ 687.328330] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 687.328334] ata6.00: failed command: READ FPDMA QUEUED [ 687.328341] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 687.328343] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 687.328347] ata6.00: status: { DRDY } [ 687.328351] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 687.328356] ata6.15: hard resetting link [ 687.820135] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 687.820762] ata6.01: limiting SATA link speed to 1.5 Gbps [ 687.820770] ata6.00: hard resetting link [ 688.312413] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 688.312476] ata6.01: hard resetting link [ 688.632754] ata6.01: SATA link down (SStatus 0 SControl 310) [ 688.633212] ata6.00: configured for UDMA/133 [ 688.680228] ata6: EH complete [ 688.680291] ata6.00: failed to read SCR 1 (Emask=0x40) [ 688.680297] ata6.01: failed to read SCR 1 (Emask=0x40) [ 688.680308] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 688.680314] ata6.15: irq_stat 0x08000000, interface fatal error [ 688.680319] ata6.15: SError: { LinkSeq } [ 688.680325] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 688.680331] ata6.00: failed command: READ FPDMA QUEUED [ 688.680349] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 688.680350] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 688.680353] ata6.00: status: { DRDY } [ 688.680357] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 688.680361] ata6.15: hard resetting link [ 689.172100] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 689.172811] ata6.01: limiting SATA link speed to 1.5 Gbps [ 689.172821] ata6.00: hard resetting link [ 689.664424] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 689.664488] ata6.01: hard resetting link [ 689.984521] ata6.01: SATA link down (SStatus 0 SControl 310) [ 689.984869] ata6.00: configured for UDMA/133 [ 690.032171] ata6: EH complete [ 690.032251] ata6.00: failed to read SCR 1 (Emask=0x40) [ 690.032258] ata6.01: failed to read SCR 1 (Emask=0x40) [ 690.032278] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 690.032281] ata6.15: irq_stat 0x08000000, interface fatal error [ 690.032285] ata6.15: SError: { LinkSeq } [ 690.032288] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 690.032292] ata6.00: failed command: READ FPDMA QUEUED [ 690.032298] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 690.032299] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 690.032302] ata6.00: status: { DRDY } [ 690.032305] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 690.032309] ata6.15: hard resetting link [ 690.524060] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 690.524666] ata6.01: limiting SATA link speed to 1.5 Gbps [ 690.524673] ata6.00: hard resetting link [ 691.016342] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 691.016403] ata6.01: hard resetting link [ 691.336541] ata6.01: SATA link down (SStatus 0 SControl 310) [ 691.336914] ata6.00: configured for UDMA/133 [ 691.384175] sd 5:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 691.384185] sd 5:0:0:0: [sdb] Sense Key : Aborted Command [current] [descriptor] [ 691.384193] Descriptor sense data with sense descriptors (in hex): [ 691.384196] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 [ 691.384212] 00 00 00 00 [ 691.384219] sd 5:0:0:0: [sdb] Add. Sense: No additional sense information [ 691.384226] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 09 50 f8 00 00 00 08 00 [ 691.384241] end_request: I/O error, dev sdb, sector 156301312 [ 691.384248] Buffer I/O error on device sdb, logical block 19537664 [ 691.384280] ata6: EH complete [ 691.384343] ata6.00: failed to read SCR 1 (Emask=0x40) [ 691.384347] ata6.01: failed to read SCR 1 (Emask=0x40) [ 691.384354] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 691.384357] ata6.15: irq_stat 0x08000000, interface fatal error [ 691.384360] ata6.15: SError: { LinkSeq } [ 691.384364] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 691.384367] ata6.00: failed command: READ FPDMA QUEUED [ 691.384373] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 691.384374] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 691.384377] ata6.00: status: { DRDY } [ 691.384381] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 691.384385] ata6.15: hard resetting link [ 691.880062] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 691.880754] ata6.01: limiting SATA link speed to 1.5 Gbps [ 691.880765] ata6.00: hard resetting link [ 692.372365] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 692.372403] ata6.01: hard resetting link [ 692.692583] ata6.01: SATA link down (SStatus 0 SControl 310) [ 692.692949] ata6.00: configured for UDMA/133 [ 692.740165] ata6: EH complete [ 692.740216] ata6.00: failed to read SCR 1 (Emask=0x40) [ 692.740221] ata6.01: failed to read SCR 1 (Emask=0x40) [ 692.740230] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 692.740234] ata6.15: irq_stat 0x08000000, interface fatal error [ 692.740238] ata6.15: SError: { LinkSeq } [ 692.740243] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 692.740247] ata6.00: failed command: READ FPDMA QUEUED [ 692.740254] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 692.740256] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 692.740260] ata6.00: status: { DRDY } [ 692.740264] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 692.740269] ata6.15: hard resetting link [ 693.232074] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 693.232724] ata6.01: limiting SATA link speed to 1.5 Gbps [ 693.232730] ata6.00: hard resetting link [ 693.724383] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 693.724433] ata6.01: hard resetting link [ 694.044698] ata6.01: SATA link down (SStatus 0 SControl 310) [ 694.045157] ata6.00: configured for UDMA/133 [ 694.092234] ata6: EH complete [ 694.092311] ata6.00: failed to read SCR 1 (Emask=0x40) [ 694.092316] ata6.01: failed to read SCR 1 (Emask=0x40) [ 694.092324] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 694.092329] ata6.15: irq_stat 0x08000000, interface fatal error [ 694.092333] ata6.15: SError: { LinkSeq } [ 694.092337] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 694.092342] ata6.00: failed command: READ FPDMA QUEUED [ 694.092349] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 694.092351] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 694.092354] ata6.00: status: { DRDY } [ 694.092358] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 694.092364] ata6.15: hard resetting link [ 694.584150] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 694.584836] ata6.01: limiting SATA link speed to 1.5 Gbps [ 694.584843] ata6.00: hard resetting link [ 695.076578] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 695.076642] ata6.01: hard resetting link [ 695.396623] ata6.01: SATA link down (SStatus 0 SControl 310) [ 695.397077] ata6.00: configured for UDMA/133 [ 695.444236] ata6: EH complete [ 695.444326] ata6.00: failed to read SCR 1 (Emask=0x40) [ 695.444332] ata6.01: failed to read SCR 1 (Emask=0x40) [ 695.444351] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 695.444355] ata6.15: irq_stat 0x08000000, interface fatal error [ 695.444371] ata6.15: SError: { LinkSeq } [ 695.444380] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 695.444388] ata6.00: failed command: READ FPDMA QUEUED [ 695.444403] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 695.444406] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 695.444414] ata6.00: status: { DRDY } [ 695.444422] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 695.444433] ata6.15: hard resetting link [ 695.936157] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 695.936846] ata6.01: limiting SATA link speed to 1.5 Gbps [ 695.936854] ata6.00: hard resetting link [ 696.428526] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 696.428575] ata6.01: hard resetting link [ 696.748561] ata6.01: SATA link down (SStatus 0 SControl 310) [ 696.748963] ata6.00: configured for UDMA/133 [ 696.796213] ata6: EH complete [ 696.796277] ata6.00: failed to read SCR 1 (Emask=0x40) [ 696.796282] ata6.01: failed to read SCR 1 (Emask=0x40) [ 696.796290] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 696.796294] ata6.15: irq_stat 0x08000000, interface fatal error [ 696.796299] ata6.15: SError: { LinkSeq } [ 696.796303] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 696.796308] ata6.00: failed command: READ FPDMA QUEUED [ 696.796315] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 696.796316] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 696.796320] ata6.00: status: { DRDY } [ 696.796324] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 696.796330] ata6.15: hard resetting link [ 697.288151] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 697.288906] ata6.01: limiting SATA link speed to 1.5 Gbps [ 697.288917] ata6.00: hard resetting link [ 697.780482] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 697.780547] ata6.01: hard resetting link [ 698.100626] ata6.01: SATA link down (SStatus 0 SControl 310) [ 698.101017] ata6.00: configured for UDMA/133 [ 698.148144] ata6: EH complete [ 698.148186] ata6.00: failed to read SCR 1 (Emask=0x40) [ 698.148190] ata6.01: failed to read SCR 1 (Emask=0x40) [ 698.148197] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 698.148201] ata6.15: irq_stat 0x08000000, interface fatal error [ 698.148204] ata6.15: SError: { LinkSeq } [ 698.148208] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 698.148212] ata6.00: failed command: READ FPDMA QUEUED [ 698.148217] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 698.148219] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 698.148222] ata6.00: status: { DRDY } [ 698.148225] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 698.148230] ata6.15: hard resetting link [ 698.640072] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 698.640828] ata6.01: limiting SATA link speed to 1.5 Gbps [ 698.640840] ata6.00: hard resetting link [ 699.132448] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 699.132498] ata6.01: hard resetting link [ 699.452673] ata6.01: SATA link down (SStatus 0 SControl 310) [ 699.453049] ata6.00: configured for UDMA/133 [ 699.500230] sd 5:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 699.500238] sd 5:0:0:0: [sdb] Sense Key : Aborted Command [current] [descriptor] [ 699.500246] Descriptor sense data with sense descriptors (in hex): [ 699.500250] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 [ 699.500266] 00 00 00 00 [ 699.500273] sd 5:0:0:0: [sdb] Add. Sense: No additional sense information [ 699.500279] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 09 50 f8 00 00 00 08 00 [ 699.500295] end_request: I/O error, dev sdb, sector 156301312 [ 699.500302] Buffer I/O error on device sdb, logical block 19537664 [ 699.500326] ata6: EH complete [ 699.500606] ata6.00: failed to read SCR 1 (Emask=0x40) [ 699.500610] ata6.01: failed to read SCR 1 (Emask=0x40) [ 699.500617] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 699.500620] ata6.15: irq_stat 0x08000000, interface fatal error [ 699.500623] ata6.15: SError: { LinkSeq } [ 699.500627] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 699.500630] ata6.00: failed command: READ FPDMA QUEUED [ 699.500637] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 699.500638] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 699.500641] ata6.00: status: { DRDY } [ 699.500644] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 699.500649] ata6.15: hard resetting link [ 699.992076] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 699.992723] ata6.01: limiting SATA link speed to 1.5 Gbps [ 699.992730] ata6.00: hard resetting link [ 700.484461] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 700.484524] ata6.01: hard resetting link [ 700.804620] ata6.01: SATA link down (SStatus 0 SControl 310) [ 700.805006] ata6.00: configured for UDMA/133 [ 700.852271] ata6: EH complete [ 700.852356] ata6.00: failed to read SCR 1 (Emask=0x40) [ 700.852365] ata6.01: failed to read SCR 1 (Emask=0x40) [ 700.852380] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 700.852389] ata6.15: irq_stat 0x08000000, interface fatal error [ 700.852397] ata6.15: SError: { LinkSeq } [ 700.852406] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 700.852415] ata6.00: failed command: READ FPDMA QUEUED [ 700.852429] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 700.852432] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 700.852440] ata6.00: status: { DRDY } [ 700.852448] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 700.852459] ata6.15: hard resetting link [ 701.344059] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 701.344607] ata6.01: limiting SATA link speed to 1.5 Gbps [ 701.344612] ata6.00: hard resetting link [ 701.836325] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 701.836366] ata6.01: hard resetting link [ 702.156363] ata6.01: SATA link down (SStatus 0 SControl 310) [ 702.156676] ata6.00: configured for UDMA/133 [ 702.204118] ata6: EH complete [ 702.204179] ata6.00: failed to read SCR 1 (Emask=0x40) [ 702.204183] ata6.01: failed to read SCR 1 (Emask=0x40) [ 702.204191] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 702.204195] ata6.15: irq_stat 0x08000000, interface fatal error [ 702.204199] ata6.15: SError: { LinkSeq } [ 702.204202] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 702.204206] ata6.00: failed command: READ FPDMA QUEUED [ 702.204212] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 702.204213] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 702.204216] ata6.00: status: { DRDY } [ 702.204220] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 702.204224] ata6.15: hard resetting link [ 702.696123] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 702.696775] ata6.01: limiting SATA link speed to 1.5 Gbps [ 702.696783] ata6.00: hard resetting link [ 703.188388] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 703.188427] ata6.01: hard resetting link [ 703.508625] ata6.01: SATA link down (SStatus 0 SControl 310) [ 703.509003] ata6.00: configured for UDMA/133 [ 703.556209] ata6: EH complete [ 703.556297] ata6.00: failed to read SCR 1 (Emask=0x40) [ 703.556303] ata6.01: failed to read SCR 1 (Emask=0x40) [ 703.556314] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 703.556319] ata6.15: irq_stat 0x08000000, interface fatal error [ 703.556325] ata6.15: SError: { LinkSeq } [ 703.556331] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 703.556347] ata6.00: failed command: READ FPDMA QUEUED [ 703.556353] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 703.556354] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 703.556368] ata6.00: status: { DRDY } [ 703.556372] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 703.556378] ata6.15: hard resetting link [ 704.048135] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 704.049012] ata6.01: limiting SATA link speed to 1.5 Gbps [ 704.049025] ata6.00: hard resetting link [ 704.540439] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 704.540503] ata6.01: hard resetting link [ 704.860621] ata6.01: SATA link down (SStatus 0 SControl 310) [ 704.861048] ata6.00: configured for UDMA/133 [ 704.908142] ata6: EH complete [ 704.908204] ata6.00: failed to read SCR 1 (Emask=0x40) [ 704.908211] ata6.01: failed to read SCR 1 (Emask=0x40) [ 704.908222] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 704.908228] ata6.15: irq_stat 0x08000000, interface fatal error [ 704.908233] ata6.15: SError: { LinkSeq } [ 704.908239] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 704.908245] ata6.00: failed command: READ FPDMA QUEUED [ 704.908255] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 704.908257] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 704.908262] ata6.00: status: { DRDY } [ 704.908276] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 704.908281] ata6.15: hard resetting link [ 705.400126] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 705.400804] ata6.01: limiting SATA link speed to 1.5 Gbps [ 705.400812] ata6.00: hard resetting link [ 705.892458] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 705.892508] ata6.01: hard resetting link [ 706.212620] ata6.01: SATA link down (SStatus 0 SControl 310) [ 706.213045] ata6.00: configured for UDMA/133 [ 706.260307] ata6: EH complete [ 706.260393] ata6.00: failed to read SCR 1 (Emask=0x40) [ 706.260403] ata6.01: failed to read SCR 1 (Emask=0x40) [ 706.260418] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 706.260426] ata6.15: irq_stat 0x08000000, interface fatal error [ 706.260434] ata6.15: SError: { LinkSeq } [ 706.260444] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 706.260452] ata6.00: failed command: READ FPDMA QUEUED [ 706.260467] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 706.260470] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 706.260478] ata6.00: status: { DRDY } [ 706.260486] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 706.260497] ata6.15: hard resetting link [ 706.752146] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 706.752813] ata6.01: limiting SATA link speed to 1.5 Gbps [ 706.752820] ata6.00: hard resetting link [ 707.244420] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 707.244470] ata6.01: hard resetting link [ 707.564593] ata6.01: SATA link down (SStatus 0 SControl 310) [ 707.564997] ata6.00: configured for UDMA/133 [ 707.612240] sd 5:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 707.612248] sd 5:0:0:0: [sdb] Sense Key : Aborted Command [current] [descriptor] [ 707.612256] Descriptor sense data with sense descriptors (in hex): [ 707.612259] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 [ 707.612275] 00 00 00 00 [ 707.612282] sd 5:0:0:0: [sdb] Add. Sense: No additional sense information [ 707.612289] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 09 50 f8 a0 00 00 08 00 [ 707.612304] end_request: I/O error, dev sdb, sector 156301472 [ 707.612311] Buffer I/O error on device sdb, logical block 19537684 [ 707.612350] ata6: EH complete [ 707.612417] ata6.00: failed to read SCR 1 (Emask=0x40) [ 707.612421] ata6.01: failed to read SCR 1 (Emask=0x40) [ 707.612428] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 707.612431] ata6.15: irq_stat 0x08000000, interface fatal error [ 707.612435] ata6.15: SError: { LinkSeq } [ 707.612438] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 707.612442] ata6.00: failed command: READ FPDMA QUEUED [ 707.612448] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 707.612449] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 707.612452] ata6.00: status: { DRDY } [ 707.612455] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 707.612460] ata6.15: hard resetting link [ 708.104133] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 708.104783] ata6.01: limiting SATA link speed to 1.5 Gbps [ 708.104791] ata6.00: hard resetting link [ 708.596300] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 708.596337] ata6.01: hard resetting link [ 708.916499] ata6.01: SATA link down (SStatus 0 SControl 310) [ 708.916886] ata6.00: configured for UDMA/133 [ 708.964183] ata6: EH complete [ 708.964245] ata6.00: failed to read SCR 1 (Emask=0x40) [ 708.964255] ata6.01: failed to read SCR 1 (Emask=0x40) [ 708.964276] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 708.964280] ata6.15: irq_stat 0x08000000, interface fatal error [ 708.964283] ata6.15: SError: { LinkSeq } [ 708.964302] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 708.964311] ata6.00: failed command: READ FPDMA QUEUED [ 708.964326] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 708.964329] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 708.964336] ata6.00: status: { DRDY } [ 708.964344] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 708.964355] ata6.15: hard resetting link [ 709.456144] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 709.456866] ata6.01: limiting SATA link speed to 1.5 Gbps [ 709.456880] ata6.00: hard resetting link [ 709.948419] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 709.948470] ata6.01: hard resetting link [ 710.268624] ata6.01: SATA link down (SStatus 0 SControl 310) [ 710.269005] ata6.00: configured for UDMA/133 [ 710.316324] ata6: EH complete [ 710.316470] ata6.00: failed to read SCR 1 (Emask=0x40) [ 710.316480] ata6.01: failed to read SCR 1 (Emask=0x40) [ 710.316494] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 710.316503] ata6.15: irq_stat 0x08000000, interface fatal error [ 710.316511] ata6.15: SError: { LinkSeq } [ 710.316520] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 710.316529] ata6.00: failed command: READ FPDMA QUEUED [ 710.316543] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 710.316546] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 710.316554] ata6.00: status: { DRDY } [ 710.316562] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 710.316573] ata6.15: hard resetting link [ 710.808134] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 710.808766] ata6.01: limiting SATA link speed to 1.5 Gbps [ 710.808774] ata6.00: hard resetting link [ 711.300518] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 711.300568] ata6.01: hard resetting link [ 711.620304] ata6.01: SATA link down (SStatus 0 SControl 310) [ 711.620597] ata6.00: configured for UDMA/133 [ 711.668102] ata6: EH complete [ 711.668166] ata6.00: failed to read SCR 1 (Emask=0x40) [ 711.668171] ata6.01: failed to read SCR 1 (Emask=0x40) [ 711.668179] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 711.668183] ata6.15: irq_stat 0x08000000, interface fatal error [ 711.668186] ata6.15: SError: { LinkSeq } [ 711.668190] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 711.668194] ata6.00: failed command: READ FPDMA QUEUED [ 711.668200] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 711.668201] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 711.668204] ata6.00: status: { DRDY } [ 711.668208] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 711.668213] ata6.15: hard resetting link [ 712.160105] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 712.160756] ata6.01: limiting SATA link speed to 1.5 Gbps [ 712.160765] ata6.00: hard resetting link [ 712.652484] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 712.652549] ata6.01: hard resetting link [ 712.972696] ata6.01: SATA link down (SStatus 0 SControl 310) [ 712.973180] ata6.00: configured for UDMA/133 [ 713.020173] ata6: EH complete [ 713.020235] ata6.00: failed to read SCR 1 (Emask=0x40) [ 713.020241] ata6.01: failed to read SCR 1 (Emask=0x40) [ 713.020252] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 713.020258] ata6.15: irq_stat 0x08000000, interface fatal error [ 713.020274] ata6.15: SError: { LinkSeq } [ 713.020277] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 713.020281] ata6.00: failed command: READ FPDMA QUEUED [ 713.020299] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 713.020300] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 713.020304] ata6.00: status: { DRDY } [ 713.020308] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 713.020314] ata6.15: hard resetting link [ 713.512059] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 713.512713] ata6.01: limiting SATA link speed to 1.5 Gbps [ 713.512720] ata6.00: hard resetting link [ 714.004191] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 714.004222] ata6.01: hard resetting link [ 714.324575] ata6.01: SATA link down (SStatus 0 SControl 310) [ 714.324960] ata6.00: configured for UDMA/133 [ 714.372144] ata6: EH complete [ 714.372206] ata6.00: failed to read SCR 1 (Emask=0x40) [ 714.372212] ata6.01: failed to read SCR 1 (Emask=0x40) [ 714.372223] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 714.372229] ata6.15: irq_stat 0x08000000, interface fatal error [ 714.372234] ata6.15: SError: { LinkSeq } [ 714.372241] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 714.372247] ata6.00: failed command: READ FPDMA QUEUED [ 714.372256] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 714.372258] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 714.372274] ata6.00: status: { DRDY } [ 714.372277] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 714.372281] ata6.15: hard resetting link [ 714.864110] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 714.864742] ata6.01: limiting SATA link speed to 1.5 Gbps [ 714.864750] ata6.00: hard resetting link [ 715.356344] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 715.356385] ata6.01: hard resetting link [ 715.676505] ata6.01: SATA link down (SStatus 0 SControl 310) [ 715.676819] ata6.00: configured for UDMA/133 [ 715.724162] sd 5:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 715.724186] sd 5:0:0:0: [sdb] Sense Key : Aborted Command [current] [descriptor] [ 715.724198] Descriptor sense data with sense descriptors (in hex): [ 715.724204] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 [ 715.724228] 00 00 00 00 [ 715.724238] sd 5:0:0:0: [sdb] Add. Sense: No additional sense information [ 715.724248] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 09 50 f8 a0 00 00 08 00 [ 715.724270] end_request: I/O error, dev sdb, sector 156301472 [ 715.724281] Buffer I/O error on device sdb, logical block 19537684 [ 715.724317] ata6: EH complete [ 715.853382] ata6.00: failed to read SCR 1 (Emask=0x40) [ 715.853393] ata6.01: failed to read SCR 1 (Emask=0x40) [ 715.853409] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 715.853418] ata6.15: irq_stat 0x08000000, interface fatal error [ 715.853427] ata6.15: SError: { LinkSeq } [ 715.853436] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 715.853445] ata6.00: failed command: READ FPDMA QUEUED [ 715.853459] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 715.853463] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 715.853470] ata6.00: status: { DRDY } [ 715.853478] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 715.853490] ata6.15: hard resetting link [ 716.344066] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 716.344701] ata6.01: limiting SATA link speed to 1.5 Gbps [ 716.344709] ata6.00: hard resetting link [ 716.836380] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 716.836421] ata6.01: hard resetting link [ 717.156541] ata6.01: SATA link down (SStatus 0 SControl 310) [ 717.156931] ata6.00: configured for UDMA/133 [ 717.204212] ata6: EH complete [ 717.204302] ata6.00: failed to read SCR 1 (Emask=0x40) [ 717.204311] ata6.01: failed to read SCR 1 (Emask=0x40) [ 717.204326] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 717.204334] ata6.15: irq_stat 0x08000000, interface fatal error [ 717.204342] ata6.15: SError: { LinkSeq } [ 717.204351] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 717.204360] ata6.00: failed command: READ FPDMA QUEUED [ 717.204374] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 717.204377] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 717.204395] ata6.00: status: { DRDY } [ 717.204399] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 717.204403] ata6.15: hard resetting link [ 717.696071] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 717.696720] ata6.01: limiting SATA link speed to 1.5 Gbps [ 717.696727] ata6.00: hard resetting link [ 718.188392] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 718.188429] ata6.01: hard resetting link [ 718.508529] ata6.01: SATA link down (SStatus 0 SControl 310) [ 718.508917] ata6.00: configured for UDMA/133 [ 718.556316] ata6: EH complete [ 718.556503] ata6.00: failed to read SCR 1 (Emask=0x40) [ 718.556513] ata6.01: failed to read SCR 1 (Emask=0x40) [ 718.556529] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 718.556537] ata6.15: irq_stat 0x08000000, interface fatal error [ 718.556545] ata6.15: SError: { LinkSeq } [ 718.556554] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 718.556563] ata6.00: failed command: READ FPDMA QUEUED [ 718.556577] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 718.556580] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 718.556588] ata6.00: status: { DRDY } [ 718.556596] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 718.556607] ata6.15: hard resetting link [ 719.048126] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 719.048774] ata6.01: limiting SATA link speed to 1.5 Gbps [ 719.048782] ata6.00: hard resetting link [ 719.540378] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 719.540427] ata6.01: hard resetting link [ 719.860494] ata6.01: SATA link down (SStatus 0 SControl 310) [ 719.860880] ata6.00: configured for UDMA/133 [ 719.908235] ata6: EH complete [ 719.908323] ata6.00: failed to read SCR 1 (Emask=0x40) [ 719.908329] ata6.01: failed to read SCR 1 (Emask=0x40) [ 719.908349] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 719.908353] ata6.15: irq_stat 0x08000000, interface fatal error [ 719.908356] ata6.15: SError: { LinkSeq } [ 719.908360] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 719.908364] ata6.00: failed command: READ FPDMA QUEUED [ 719.908369] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 719.908371] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 719.908374] ata6.00: status: { DRDY } [ 719.908377] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 719.908382] ata6.15: hard resetting link [ 720.400140] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 720.400810] ata6.01: limiting SATA link speed to 1.5 Gbps [ 720.400816] ata6.00: hard resetting link [ 720.612053] ata6.00: failed to read SCR 2 (Emask=0x40) [ 720.612059] ata6.00: COMRESET failed (errno=-5) [ 720.612065] ata6.00: failed to read SCR 0 (Emask=0x40) [ 720.612069] ata6.00: reset failed, giving up [ 720.612077] ata6.15: hard resetting link [ 720.932158] ata6.15: SATA link down (SStatus 0 SControl 310) [ 723.932057] ata6.15: qc timeout (cmd 0xe4) [ 723.932071] ata6.15: failed to read PMP GSCR[0] (Emask=0x4) [ 723.932076] ata6.15: PMP revalidation failed (errno=-5) [ 725.932077] ata6.15: hard resetting link [ 726.252056] ata6.15: SATA link down (SStatus 0 SControl 310) [ 727.212059] ata6.15: failed to read PMP GSCR[0] (Emask=0x100) [ 727.212066] ata6.15: PMP revalidation failed (errno=-5) [ 731.252150] ata6.15: hard resetting link [ 731.744107] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 731.744698] ata6.00: hard resetting link [ 732.240432] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 732.240498] ata6.01: hard resetting link [ 732.560605] ata6.01: SATA link down (SStatus 0 SControl 310) [ 732.560984] ata6.00: configured for UDMA/133 [ 732.608211] ata6: EH complete [ 732.608277] ata6.00: failed to read SCR 1 (Emask=0x40) [ 732.608282] ata6.01: failed to read SCR 1 (Emask=0x40) [ 732.608290] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 732.608295] ata6.15: irq_stat 0x08000000, interface fatal error [ 732.608299] ata6.15: SError: { LinkSeq } [ 732.608303] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 732.608308] ata6.00: failed command: READ FPDMA QUEUED [ 732.608315] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 732.608317] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 732.608321] ata6.00: status: { DRDY } [ 732.608325] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 732.608330] ata6.15: hard resetting link [ 733.100086] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 733.100726] ata6.01: limiting SATA link speed to 1.5 Gbps [ 733.100738] ata6.00: hard resetting link [ 733.592452] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 733.592502] ata6.01: hard resetting link [ 733.912822] ata6.01: SATA link down (SStatus 0 SControl 310) [ 733.913282] ata6.00: configured for UDMA/133 [ 733.960216] ata6: EH complete [ 733.960303] ata6.00: failed to read SCR 1 (Emask=0x40) [ 733.960309] ata6.01: failed to read SCR 1 (Emask=0x40) [ 733.960319] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 733.960325] ata6.15: irq_stat 0x08000000, interface fatal error [ 733.960331] ata6.15: SError: { LinkSeq } [ 733.960346] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 733.960350] ata6.00: failed command: READ FPDMA QUEUED [ 733.960356] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 733.960357] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 733.960360] ata6.00: status: { DRDY } [ 733.960363] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 733.960368] ata6.15: hard resetting link [ 734.452178] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 734.453037] ata6.01: limiting SATA link speed to 1.5 Gbps [ 734.453049] ata6.00: hard resetting link [ 734.944512] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 734.944575] ata6.01: hard resetting link [ 735.264664] ata6.01: SATA link down (SStatus 0 SControl 310) [ 735.265061] ata6.00: configured for UDMA/133 [ 735.312161] sd 5:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 735.312169] sd 5:0:0:0: [sdb] Sense Key : Aborted Command [current] [descriptor] [ 735.312177] Descriptor sense data with sense descriptors (in hex): [ 735.312181] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 [ 735.312197] 00 00 00 00 [ 735.312204] sd 5:0:0:0: [sdb] Add. Sense: No additional sense information [ 735.312210] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 09 50 f8 00 00 00 08 00 [ 735.312226] end_request: I/O error, dev sdb, sector 156301312 [ 735.312233] Buffer I/O error on device sdb, logical block 19537664 [ 735.312275] ata6: EH complete [ 735.312340] ata6.00: failed to read SCR 1 (Emask=0x40) [ 735.312344] ata6.01: failed to read SCR 1 (Emask=0x40) [ 735.312352] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 735.312355] ata6.15: irq_stat 0x08000000, interface fatal error [ 735.312358] ata6.15: SError: { LinkSeq } [ 735.312362] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 735.312365] ata6.00: failed command: READ FPDMA QUEUED [ 735.312371] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 735.312372] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 735.312375] ata6.00: status: { DRDY } [ 735.312379] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 735.312383] ata6.15: hard resetting link [ 735.804129] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 735.804781] ata6.01: limiting SATA link speed to 1.5 Gbps [ 735.804789] ata6.00: hard resetting link [ 736.296457] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 736.296506] ata6.01: hard resetting link [ 736.616670] ata6.01: SATA link down (SStatus 0 SControl 310) [ 736.617064] ata6.00: configured for UDMA/133 [ 736.664229] ata6: EH complete [ 736.664318] ata6.00: failed to read SCR 1 (Emask=0x40) [ 736.664324] ata6.01: failed to read SCR 1 (Emask=0x40) [ 736.664334] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 736.664350] ata6.15: irq_stat 0x08000000, interface fatal error [ 736.664353] ata6.15: SError: { LinkSeq } [ 736.664357] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 736.664360] ata6.00: failed command: READ FPDMA QUEUED [ 736.664366] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 736.664367] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 736.664370] ata6.00: status: { DRDY } [ 736.664374] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 736.664378] ata6.15: hard resetting link [ 737.160148] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 737.160817] ata6.01: limiting SATA link speed to 1.5 Gbps [ 737.160825] ata6.00: hard resetting link [ 737.652428] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 737.652478] ata6.01: hard resetting link [ 737.972471] ata6.01: SATA link down (SStatus 0 SControl 310) [ 737.972775] ata6.00: configured for UDMA/133 [ 738.020190] ata6: EH complete [ 738.020219] ata6.00: failed to read SCR 1 (Emask=0x40) [ 738.020222] ata6.01: failed to read SCR 1 (Emask=0x40) [ 738.020232] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 738.020236] ata6.15: irq_stat 0x08000000, interface fatal error [ 738.020239] ata6.15: SError: { LinkSeq } [ 738.020242] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 738.020246] ata6.00: failed command: READ FPDMA QUEUED [ 738.020252] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 738.020253] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 738.020256] ata6.00: status: { DRDY } [ 738.020259] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 738.020265] ata6.15: hard resetting link [ 738.512147] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 738.512840] ata6.01: limiting SATA link speed to 1.5 Gbps [ 738.512848] ata6.00: hard resetting link [ 739.008389] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 739.008439] ata6.01: hard resetting link [ 739.328460] ata6.01: SATA link down (SStatus 0 SControl 310) [ 739.328775] ata6.00: configured for UDMA/133 [ 739.376208] ata6: EH complete [ 739.390092] ata6.00: failed to read SCR 1 (Emask=0x40) [ 739.390096] ata6.01: failed to read SCR 1 (Emask=0x40) [ 739.390104] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 739.390107] ata6.15: irq_stat 0x08000000, interface fatal error [ 739.390111] ata6.15: SError: { LinkSeq } [ 739.390114] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 739.390118] ata6.00: failed command: READ FPDMA QUEUED [ 739.390124] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 739.390125] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 739.390128] ata6.00: status: { DRDY } [ 739.390131] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 739.390135] ata6.15: hard resetting link [ 739.880060] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 739.880548] ata6.01: limiting SATA link speed to 1.5 Gbps [ 739.880553] ata6.00: hard resetting link [ 740.372271] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 740.372299] ata6.01: hard resetting link [ 740.692414] ata6.01: SATA link down (SStatus 0 SControl 310) [ 740.692720] ata6.00: configured for UDMA/133 [ 740.742629] ata6: EH complete [ 740.742668] ata6.00: failed to read SCR 1 (Emask=0x40) [ 740.742672] ata6.01: failed to read SCR 1 (Emask=0x40) [ 740.742680] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 740.742684] ata6.15: irq_stat 0x08000000, interface fatal error [ 740.742688] ata6.15: SError: { LinkSeq } [ 740.742691] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 740.742695] ata6.00: failed command: READ FPDMA QUEUED [ 740.742701] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 740.742702] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 740.742705] ata6.00: status: { DRDY } [ 740.742708] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 740.742713] ata6.15: hard resetting link [ 741.232124] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 741.232776] ata6.01: limiting SATA link speed to 1.5 Gbps [ 741.232784] ata6.00: hard resetting link [ 741.728321] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 741.728371] ata6.01: hard resetting link [ 742.048852] ata6.01: SATA link down (SStatus 0 SControl 310) [ 742.049221] ata6.00: configured for UDMA/133 [ 742.096209] ata6: EH complete [ 742.096303] ata6.00: failed to read SCR 1 (Emask=0x40) [ 742.096309] ata6.01: failed to read SCR 1 (Emask=0x40) [ 742.096320] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 742.096326] ata6.15: irq_stat 0x08000000, interface fatal error [ 742.096331] ata6.15: SError: { LinkSeq } [ 742.096337] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 742.096352] ata6.00: failed command: READ FPDMA QUEUED [ 742.096358] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 742.096359] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 742.096362] ata6.00: status: { DRDY } [ 742.096365] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 742.096370] ata6.15: hard resetting link [ 742.588160] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 742.588768] ata6.01: limiting SATA link speed to 1.5 Gbps [ 742.588776] ata6.00: hard resetting link [ 743.080419] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 743.080469] ata6.01: hard resetting link [ 743.400658] ata6.01: SATA link down (SStatus 0 SControl 310) [ 743.401014] ata6.00: configured for UDMA/133 [ 743.448244] sd 5:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 743.448250] sd 5:0:0:0: [sdb] Sense Key : Aborted Command [current] [descriptor] [ 743.448256] Descriptor sense data with sense descriptors (in hex): [ 743.448259] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 [ 743.448271] 00 00 00 00 [ 743.448276] sd 5:0:0:0: [sdb] Add. Sense: No additional sense information [ 743.448281] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 09 50 f8 00 00 00 08 00 [ 743.448293] end_request: I/O error, dev sdb, sector 156301312 [ 743.448299] Buffer I/O error on device sdb, logical block 19537664 [ 743.448318] ata6: EH complete [ 743.448402] ata6.00: failed to read SCR 1 (Emask=0x40) [ 743.448407] ata6.01: failed to read SCR 1 (Emask=0x40) [ 743.448415] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 743.448419] ata6.15: irq_stat 0x08000000, interface fatal error [ 743.448423] ata6.15: SError: { LinkSeq } [ 743.448428] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 743.448432] ata6.00: failed command: READ FPDMA QUEUED [ 743.448439] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 743.448441] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 743.448445] ata6.00: status: { DRDY } [ 743.448449] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 743.448454] ata6.15: hard resetting link [ 743.940088] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 743.940836] ata6.01: limiting SATA link speed to 1.5 Gbps [ 743.940847] ata6.00: hard resetting link [ 744.432340] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 744.432391] ata6.01: hard resetting link [ 744.752606] ata6.01: SATA link down (SStatus 0 SControl 310) [ 744.752962] ata6.00: configured for UDMA/133 [ 744.800213] ata6: EH complete [ 744.800349] ata6.00: failed to read SCR 1 (Emask=0x40) [ 744.800359] ata6.01: failed to read SCR 1 (Emask=0x40) [ 744.800374] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 744.800383] ata6.15: irq_stat 0x08000000, interface fatal error [ 744.800391] ata6.15: SError: { LinkSeq } [ 744.800400] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 744.800409] ata6.00: failed command: READ FPDMA QUEUED [ 744.800424] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 744.800427] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 744.800435] ata6.00: status: { DRDY } [ 744.800443] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 744.800453] ata6.15: hard resetting link [ 745.292056] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 745.292657] ata6.01: limiting SATA link speed to 1.5 Gbps [ 745.292662] ata6.00: hard resetting link [ 745.784346] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 745.784397] ata6.01: hard resetting link [ 746.104745] ata6.01: SATA link down (SStatus 0 SControl 310) [ 746.105133] ata6.00: configured for UDMA/133 [ 746.152231] ata6: EH complete [ 746.152284] ata6.00: failed to read SCR 1 (Emask=0x40) [ 746.152289] ata6.01: failed to read SCR 1 (Emask=0x40) [ 746.152298] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 746.152302] ata6.15: irq_stat 0x08000000, interface fatal error [ 746.152307] ata6.15: SError: { LinkSeq } [ 746.152311] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 746.152316] ata6.00: failed command: READ FPDMA QUEUED [ 746.152323] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 746.152325] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 746.152328] ata6.00: status: { DRDY } [ 746.152333] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 746.152338] ata6.15: hard resetting link [ 746.644140] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 746.644790] ata6.01: limiting SATA link speed to 1.5 Gbps [ 746.644798] ata6.00: hard resetting link [ 747.136430] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 747.136480] ata6.01: hard resetting link [ 747.456721] ata6.01: SATA link down (SStatus 0 SControl 310) [ 747.457118] ata6.00: configured for UDMA/133 [ 747.504200] ata6: EH complete [ 747.504260] ata6.00: failed to read SCR 1 (Emask=0x40) [ 747.504265] ata6.01: failed to read SCR 1 (Emask=0x40) [ 747.504273] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 747.504278] ata6.15: irq_stat 0x08000000, interface fatal error [ 747.504282] ata6.15: SError: { LinkSeq } [ 747.504286] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 747.504291] ata6.00: failed command: READ FPDMA QUEUED [ 747.504298] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 747.504300] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 747.504303] ata6.00: status: { DRDY } [ 747.504307] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 747.504313] ata6.15: hard resetting link [ 747.996149] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 747.996810] ata6.01: limiting SATA link speed to 1.5 Gbps [ 747.996818] ata6.00: hard resetting link [ 748.488395] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 748.488431] ata6.01: hard resetting link [ 748.808659] ata6.01: SATA link down (SStatus 0 SControl 310) [ 748.809028] ata6.00: configured for UDMA/133 [ 748.856345] ata6: EH complete [ 748.856443] ata6.00: failed to read SCR 1 (Emask=0x40) [ 748.856454] ata6.01: failed to read SCR 1 (Emask=0x40) [ 748.856470] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 748.856478] ata6.15: irq_stat 0x08000000, interface fatal error [ 748.856487] ata6.15: SError: { LinkSeq } [ 748.856496] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 748.856505] ata6.00: failed command: READ FPDMA QUEUED [ 748.856519] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 748.856522] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 748.856530] ata6.00: status: { DRDY } [ 748.856538] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 748.856550] ata6.15: hard resetting link [ 749.348144] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 749.348803] ata6.01: limiting SATA link speed to 1.5 Gbps [ 749.348810] ata6.00: hard resetting link [ 749.840336] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 749.840386] ata6.01: hard resetting link [ 750.160553] ata6.01: SATA link down (SStatus 0 SControl 310) [ 750.161060] ata6.00: configured for UDMA/133 [ 750.208200] ata6: EH complete [ 750.208258] ata6.00: failed to read SCR 1 (Emask=0x40) [ 750.208265] ata6.01: failed to read SCR 1 (Emask=0x40) [ 750.208275] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 750.208281] ata6.15: irq_stat 0x08000000, interface fatal error [ 750.208286] ata6.15: SError: { LinkSeq } [ 750.208292] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 750.208299] ata6.00: failed command: READ FPDMA QUEUED [ 750.208308] ata6.00: cmd 60/08:00:a0:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 750.208311] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 750.208316] ata6.00: status: { DRDY } [ 750.208321] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 750.208328] ata6.15: hard resetting link [ 750.700061] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 750.700835] ata6.01: limiting SATA link speed to 1.5 Gbps [ 750.700846] ata6.00: hard resetting link [ 751.192382] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 751.192431] ata6.01: hard resetting link [ 751.512573] ata6.01: SATA link down (SStatus 0 SControl 310) [ 751.512950] ata6.00: configured for UDMA/133 [ 751.560304] sd 5:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 751.560317] sd 5:0:0:0: [sdb] Sense Key : Aborted Command [current] [descriptor] [ 751.560329] Descriptor sense data with sense descriptors (in hex): [ 751.560335] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 [ 751.560359] 00 00 00 00 [ 751.560369] sd 5:0:0:0: [sdb] Add. Sense: No additional sense information [ 751.560379] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 09 50 f8 a0 00 00 08 00 [ 751.560402] end_request: I/O error, dev sdb, sector 156301472 [ 751.560413] Buffer I/O error on device sdb, logical block 19537684 [ 751.560457] ata6: EH complete [ 751.617810] ata6.00: failed to read SCR 1 (Emask=0x40) [ 751.617821] ata6.01: failed to read SCR 1 (Emask=0x40) [ 751.617836] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 751.617845] ata6.15: irq_stat 0x08000000, interface fatal error [ 751.617853] ata6.15: SError: { LinkSeq } [ 751.617862] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 751.617871] ata6.00: failed command: READ FPDMA QUEUED [ 751.617886] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 751.617889] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 751.617897] ata6.00: status: { DRDY } [ 751.617905] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 751.617917] ata6.15: hard resetting link [ 752.108117] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 752.108772] ata6.01: limiting SATA link speed to 1.5 Gbps [ 752.108779] ata6.00: hard resetting link [ 752.600385] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 752.600435] ata6.01: hard resetting link [ 752.920598] ata6.01: SATA link down (SStatus 0 SControl 310) [ 752.921009] ata6.00: configured for UDMA/133 [ 752.968208] ata6: EH complete [ 752.968270] ata6.00: failed to read SCR 1 (Emask=0x40) [ 752.968275] ata6.01: failed to read SCR 1 (Emask=0x40) [ 752.968283] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 752.968287] ata6.15: irq_stat 0x08000000, interface fatal error [ 752.968291] ata6.15: SError: { LinkSeq } [ 752.968296] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 752.968301] ata6.00: failed command: READ FPDMA QUEUED [ 752.968308] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 752.968309] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 752.968313] ata6.00: status: { DRDY } [ 752.968317] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 752.968323] ata6.15: hard resetting link [ 753.460068] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 753.460748] ata6.01: limiting SATA link speed to 1.5 Gbps [ 753.460756] ata6.00: hard resetting link [ 753.952572] ata6.00: SATA link up 3.0 Gbps (SStatus 123 SControl 310) [ 753.952678] ata6.01: hard resetting link [ 754.272625] ata6.01: SATA link down (SStatus 0 SControl 310) [ 754.273012] ata6.00: configured for UDMA/133 [ 754.320294] ata6: EH complete [ 754.320384] ata6.00: failed to read SCR 1 (Emask=0x40) [ 754.320395] ata6.01: failed to read SCR 1 (Emask=0x40) [ 754.320410] ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x6 frozen [ 754.320418] ata6.15: irq_stat 0x08000000, interface fatal error [ 754.320427] ata6.15: SError: { LinkSeq } [ 754.320435] ata6.00: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen [ 754.320445] ata6.00: failed command: READ FPDMA QUEUED [ 754.320459] ata6.00: cmd 60/08:00:00:f8:50/00:00:09:00:00/40 tag 0 ncq 4096 in [ 754.320462] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x100 (unknown error) [ 754.320480] ata6.00: status: { DRDY } [ 754.320483] ata6.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen [ 754.320488] ata6.15: hard resetting link [ 754.812135] ata6.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 754.812785] ata6.01: limiting SATA link speed to 1.5 Gbps [ 754.812793] ata6.00: hard resetting link