00:00.0 Host bridge [0600]: Intel Corporation 82845 845 [Brookdale] Chipset Host Bridge [8086:1a30] (rev 04)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
	Capabilities: [e4] Vendor Specific Information: Len=04 <?>
	Capabilities: [a0] AGP version 2.0
		Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
		Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
	Kernel driver in use: agpgart-intel
	Kernel modules: intel-agp

00:01.0 PCI bridge [0604]: Intel Corporation 82845 845 [Brookdale] Chipset AGP Bridge [8086:1a31] (rev 04) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 96
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: d0100000-d01fffff
	Prefetchable memory behind bridge: e8000000-efffffff
	Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Kernel modules: shpchp

00:1d.0 USB Controller [0c03]: Intel Corporation 82801CA/CAM USB Controller #1 [8086:2482] (rev 02) (prog-if 00 [UHCI])
	Subsystem: IBM ThinkPad A/T/X Series [1014:0220]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 11
	Region 4: I/O ports at 1800 [size=32]
	Kernel driver in use: uhci_hcd

00:1d.1 USB Controller [0c03]: Intel Corporation 82801CA/CAM USB Controller #2 [8086:2484] (rev 02) (prog-if 00 [UHCI])
	Subsystem: IBM ThinkPad A/T/X Series [1014:0220]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 11
	Region 4: I/O ports at 1820 [size=32]
	Kernel driver in use: uhci_hcd

00:1d.2 USB Controller [0c03]: Intel Corporation 82801CA/CAM USB Controller #3 [8086:2487] (rev 02) (prog-if 00 [UHCI])
	Subsystem: IBM ThinkPad A/T/X Series [1014:0220]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin C routed to IRQ 11
	Region 4: I/O ports at 1840 [size=32]
	Kernel driver in use: uhci_hcd

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 42) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Bus: primary=00, secondary=02, subordinate=17, sec-latency=64
	I/O behind bridge: 00003000-00008fff
	Memory behind bridge: d0200000-dfffffff
	Prefetchable memory behind bridge: f0000000-f80fffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR+
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Kernel modules: shpchp

00:1f.0 ISA bridge [0601]: Intel Corporation 82801CAM ISA Bridge (LPC) [8086:248c] (rev 02)
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Kernel modules: iTCO_wdt, intel-rng

00:1f.1 IDE interface [0101]: Intel Corporation 82801CAM IDE U100 Controller [8086:248a] (rev 02) (prog-if 8a [Master SecP PriP])
	Subsystem: IBM ThinkPad A/T/X Series [1014:0220]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 11
	Region 0: I/O ports at 01f0 [size=8]
	Region 1: I/O ports at 03f4 [size=1]
	Region 2: I/O ports at 0170 [size=8]
	Region 3: I/O ports at 0374 [size=1]
	Region 4: I/O ports at 1860 [size=16]
	Region 5: Memory at 40000000 (32-bit, non-prefetchable) [size=1K]
	Kernel driver in use: ata_piix

00:1f.3 SMBus [0c05]: Intel Corporation 82801CA/CAM SMBus Controller [8086:2483] (rev 02)
	Subsystem: IBM ThinkPad A/T/X Series [1014:0220]
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin B routed to IRQ 11
	Region 4: I/O ports at 1880 [size=32]
	Kernel modules: i2c-i801

00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801CA/CAM AC'97 Audio Controller [8086:2485] (rev 02)
	Subsystem: IBM ThinkPad T30 [1014:0508]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 11
	Region 0: I/O ports at 1c00 [size=256]
	Region 1: I/O ports at 18c0 [size=64]
	Kernel driver in use: Intel ICH
	Kernel modules: snd-intel8x0

01:00.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon RV200 LX [Mobility FireGL 7800 M7] [1002:4c58] (prog-if 00 [VGA controller])
	Subsystem: IBM Device [1014:0518]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B+ DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 66 (2000ns min), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
	Region 1: I/O ports at 2000 [size=256]
	Region 2: Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
	[virtual] Expansion ROM at d0120000 [disabled] [size=128K]
	Capabilities: [58] AGP version 2.0
		Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
		Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: radeon
	Kernel modules: radeon, radeonfb

02:00.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c476 II [1180:0476] (rev a8)
	Subsystem: IBM ThinkPad A/T/X Series [1014:0185]
	Physical Slot: 1
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 168
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at 50000000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=02, secondary=10, subordinate=13, sec-latency=176
	Memory window 0: f0000000-f3fff000 (prefetchable)
	Memory window 1: d4000000-d7fff000
	I/O window 0: 00004000-000040ff
	I/O window 1: 00004400-000044ff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
	16-bit legacy interface ports at 0001
	Kernel driver in use: yenta_cardbus
	Kernel modules: yenta_socket

02:00.1 CardBus bridge [0607]: Ricoh Co Ltd RL5c476 II [1180:0476] (rev a8)
	Subsystem: IBM ThinkPad A/T/X Series [1014:0185]
	Physical Slot: 1
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 168
	Interrupt: pin B routed to IRQ 11
	Region 0: Memory at 50100000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=02, secondary=14, subordinate=17, sec-latency=176
	Memory window 0: f4000000-f7fff000 (prefetchable)
	Memory window 1: d8000000-dbfff000
	I/O window 0: 00004800-000048ff
	I/O window 1: 00004c00-00004cff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
	16-bit legacy interface ports at 0001
	Kernel driver in use: yenta_cardbus
	Kernel modules: yenta_socket

02:00.2 FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd R5C552 IEEE 1394 Controller [1180:0552] (prog-if 10 [OHCI])
	Subsystem: IBM ThinkPad A/T/X Series [1014:0511]
	Physical Slot: 1
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (500ns min, 1000ns max)
	Interrupt: pin C routed to IRQ 11
	Region 0: Memory at d0200000 (32-bit, non-prefetchable) [size=2K]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME+
	Kernel driver in use: firewire_ohci
	Kernel modules: firewire-ohci, ohci1394

02:02.0 Ethernet controller [0200]: 3Com Corporation 3c556B CardBus [Tornado] [10b7:6056] (rev 20)
	Subsystem: 3Com Corporation 10/100 Mini PCI Ethernet Adapter [10b7:6556]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 80 (2500ns min, 2500ns max), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 11
	Region 0: I/O ports at 7000 [size=256]
	Region 1: Memory at d0200c00 (32-bit, non-prefetchable) [size=128]
	Region 2: Memory at d0200800 (32-bit, non-prefetchable) [size=128]
	[virtual] Expansion ROM at f8020000 [disabled] [size=128K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
	Kernel driver in use: 3c59x
	Kernel modules: 3c59x

02:02.1 Communication controller [0780]: 3Com Corporation Mini PCI 56k Winmodem [10b7:1007] (rev 20)
	Subsystem: 3Com Corporation Mini PCI 56K Modem [10b7:615c]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 80 (2500ns min, 2500ns max), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 11
	Region 0: I/O ports at 7400 [size=256]
	Region 1: Memory at d0201400 (32-bit, non-prefetchable) [size=256]
	Region 2: Memory at d0201000 (32-bit, non-prefetchable) [size=128]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0+,D1-,D2+,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-

02:03.0 PCI bridge [0604]: Texas Instruments PCI2032 PCI Docking Bridge [104c:ac22] (prog-if 01 [Subtractive decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 32 bytes
	Bus: primary=02, secondary=09, subordinate=0f, sec-latency=68
	I/O behind bridge: 00003000-00003fff
	Memory behind bridge: 44000000-4bffffff
	Prefetchable memory behind bridge: 54000000-5bffffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [80] Power Management version 1
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
		Bridge: PM- B3+

09:00.0 Multimedia video controller [0400]: Brooktree Corporation Bt848 Video Capture [109e:0350] (rev 12)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 128 (4000ns min, 10000ns max)
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at f8000000 (32-bit, prefetchable) [size=4K]
	Kernel driver in use: bttv
	Kernel modules: bttv

09:01.0 IDE interface [0101]: Silicon Image, Inc. PCI0648 [1095:0648] (rev 01) (prog-if 8f [Master SecP SecO PriP PriO])
	Subsystem: Silicon Image, Inc. PCI0648 [1095:0648]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (500ns min, 1000ns max)
	Interrupt: pin A routed to IRQ 11
	Region 0: I/O ports at 8020 [size=8]
	Region 1: I/O ports at 8014 [size=4]
	Region 2: I/O ports at 8018 [size=8]
	Region 3: I/O ports at 8010 [size=4]
	Region 4: I/O ports at 8000 [size=16]
	Capabilities: [60] Power Management version 1
		Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=3 PME-
	Kernel driver in use: pata_cmd64x
	Kernel modules: pata_cmd64x

09:02.0 CardBus bridge [0607]: Texas Instruments PCI1420 PC card Cardbus Controller [104c:ac51]
	Subsystem: IBM ThinkPad A20m [1014:0148]
	Physical Slot: 3
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 168, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at 52000000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=09, secondary=0a, subordinate=0d, sec-latency=176
	Memory window 0: 54000000-57fff000 (prefetchable)
	Memory window 1: 44000000-47fff000
	I/O window 0: 00003000-000030ff
	I/O window 1: 00003400-000034ff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
	16-bit legacy interface ports at 0001
	Kernel driver in use: yenta_cardbus
	Kernel modules: yenta_socket

09:02.1 CardBus bridge [0607]: Texas Instruments PCI1420 PC card Cardbus Controller [104c:ac51]
	Subsystem: IBM ThinkPad A20m [1014:0148]
	Physical Slot: 3
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 168, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at 53000000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=09, secondary=0e, subordinate=0e, sec-latency=176
	Memory window 0: 58000000-5bfff000 (prefetchable)
	Memory window 1: 48000000-4bfff000
	I/O window 0: 00003800-000038ff
	I/O window 1: 00003c00-00003cff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
	16-bit legacy interface ports at 0001
	Kernel driver in use: yenta_cardbus
	Kernel modules: yenta_socket

10:00.0 Network controller [0280]: RaLink RT2500 802.11g [1814:0201] (rev 01)
	Subsystem: Giga-byte Technology Device [1458:6831]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at <ignored> (32-bit, non-prefetchable) [disabled]
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel modules: rt2500pci