[   15.120044] hda-intel: azx_get_response timeout, switching to polling mode: last cmd=0x020c0000
[   15.120064] hda_codec: ALC662 rev1: BIOS auto-probing.
[   15.122167] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input9
[   15.380060] render error detected, EIR: 0x00000010
[   15.380152] page table error
[   15.380203]   PGTBL_ER: 0x00000010
[   15.380263] [drm:i915_handle_error] *ERROR* EIR stuck: 0x00000010, masking
[   15.380388] render error detected, EIR: 0x00000010
[   15.380469] page table error
[   15.380519]   PGTBL_ER: 0x00000010
[   15.788652] pci 0000:01:00.0: reg 10 64bit mmio: [0x000000-0x00ffff]
[   15.839320] cfg80211: Calling CRDA to update world regulatory domain
[   15.893810] cfg80211: World regulatory domain updated:
[   15.893820] 	(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   15.893827] 	(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   15.893834] 	(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   15.893840] 	(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   15.893846] 	(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   15.893852] 	(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   15.915752] ath5k 0000:01:00.0: enabling device (0000 -> 0002)
[   15.915769] ath5k 0000:01:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[   15.915789] ath5k 0000:01:00.0: setting latency timer to 64
[   15.915847] ath5k 0000:01:00.0: registered as 'phy0'
[   16.419078] ath: EEPROM regdomain: 0x60
[   16.419084] ath: EEPROM indicates we should expect a direct regpair map
[   16.419093] ath: Country alpha2 being used: 00
[   16.419097] ath: Regpair used: 0x60
[   16.432812] phy0: Selected rate control algorithm 'minstrel'
[   16.434265] Registered led device: ath5k-phy0::rx
[   16.434308] Registered led device: ath5k-phy0::tx
[   16.434316] ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY: 0x70)
[   17.016225] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   17.055929] ppdev: user-space parallel port driver
[   27.777857] wlan0: deauthenticating from 00:e0:98:d9:9a:cd by local choice (reason=3)
[   27.884111] wlan0: direct probe to AP 00:e0:98:d9:9a:cd (try 1)
[   27.886965] wlan0: direct probe responded
[   27.886975] wlan0: authenticate with AP 00:e0:98:d9:9a:cd (try 1)
[   27.888358] wlan0: authenticated
[   27.888436] wlan0: associate with AP 00:e0:98:d9:9a:cd (try 1)
[   27.891431] wlan0: RX AssocResp from 00:e0:98:d9:9a:cd (capab=0x471 status=0 aid=1)
[   27.891439] wlan0: associated
[   27.892793] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   38.380051] wlan0: no IPv6 routers present