[   12.541418] usb 1-4: reset high speed USB device using ehci_hcd and address 4
[   12.566074] EXT4-fs (sda3): mounted filesystem with ordered data mode
[   12.694595] usb 1-4: firmware: requesting isl3887usb
[   12.707889] phy0: p54 detected a LM87 firmware
[   12.707893] p54: rx_mtu reduced from 3240 to 2384
[   12.707896] phy0: FW rev 2.13.24.0 - Softmac protocol 5.9
[   12.707898] phy0: cryptographic accelerator WEP:YES, TKIP:YES, CCMP:YES
[   13.471036]   alloc irq_desc for 27 on node 0
[   13.471042]   alloc kstat_irqs on node 0
[   13.471053] forcedeth 0000:00:07.0: irq 27 for MSI/MSI-X
[   13.471242] eth0: no link during initialization.
[   13.472593] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   13.789603] phy0: hwaddr 00:12:17:93:31:27, MAC:isl3887 RF:Frisbee
[   13.813994] phy0: Selected rate control algorithm 'minstrel'
[   13.814592] Registered led device: p54-phy0::assoc
[   13.814608] Registered led device: p54-phy0::tx
[   13.814621] Registered led device: p54-phy0::rx
[   13.814635] Registered led device: p54-phy0::radio
[   13.814651] usb 1-4: is registered as 'phy0'
[   13.814678] usbcore: registered new interface driver p54usb
[   13.874806] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   13.890026] hda_codec: ALC1200: BIOS auto-probing.
[   14.670086] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:05.0/input/input5
[   67.521750] usb 1-4: USB disconnect, address 4
[   70.340029] usb 1-4: new high speed USB device using ehci_hcd and address 5
[   70.620024] usb 1-4: reset high speed USB device using ehci_hcd and address 5
[   70.771715] usb 1-4: firmware: requesting isl3887usb
[   70.774268] phy1: p54 detected a LM87 firmware
[   70.774273] p54: rx_mtu reduced from 3240 to 2384
[   70.774275] phy1: FW rev 2.13.24.0 - Softmac protocol 5.9
[   70.774277] phy1: cryptographic accelerator WEP:YES, TKIP:YES, CCMP:YES
[   71.768853] phy1: hwaddr 00:12:17:93:31:27, MAC:isl3887 RF:Frisbee
[   71.773117] phy1: Selected rate control algorithm 'minstrel'
[   71.773685] Registered led device: p54-phy1::assoc
[   71.773700] Registered led device: p54-phy1::tx
[   71.773716] Registered led device: p54-phy1::rx
[   71.773732] Registered led device: p54-phy1::radio
[   71.773744] usb 1-4: is registered as 'phy1'
[   71.820949] ADDRCONF(NETDEV_UP): wlan0: link is not ready