00:00.0 Host bridge [0600]: Silicon Integrated Systems [SiS] 760/M760 Host [1039:0760] (rev 02)
	Subsystem: Hewlett-Packard Company Device [103c:2a04]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 32
	Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=64M]
	Capabilities: [a0] AGP version 3.1
		Status: RQ=32 Iso- ArqSz=2 Cal=3 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3+ Rate=x4,x8
		Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
	Capabilities: [d0] HyperTransport: Slave or Primary Interface
		!!! Possibly incomplete decoding
		Command: BaseUnitID=0 UnitCnt=9 MastHost- DefDir-
		Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC+ TXO- <CRCErr=0
		Link Config 0: MLWI=16bit MLWO=16bit LWI=8bit LWO=16bit
		Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
		Link Config 1: MLWI=N/C MLWO=N/C LWI=N/C LWO=N/C
		Revision ID: 1.02
	Capabilities: [f0] HyperTransport: Interrupt Discovery and Configuration
	Kernel driver in use: agpgart-amd64
	Kernel modules: sis-agp, amd64-agp

00:01.0 PCI bridge [0604]: Silicon Integrated Systems [SiS] SG86C202 [1039:0002]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 99
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
	I/O behind bridge: 00009000-00009fff
	Memory behind bridge: e4000000-e5ffffff
	Prefetchable memory behind bridge: d0000000-dfffffff
	Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Kernel modules: shpchp

00:02.0 ISA bridge [0601]: Silicon Integrated Systems [SiS] SiS964 [MuTIOL Media IO] [1039:0964] (rev 36)
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0

00:02.5 IDE interface [0101]: Silicon Integrated Systems [SiS] 5513 [IDE] [1039:5513] (rev 01) (prog-if 80 [Master])
	Subsystem: Hewlett-Packard Company Device [103c:2a04]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 128
	Region 0: I/O ports at 01f0 [size=8]
	Region 1: I/O ports at 03f4 [size=1]
	Region 2: I/O ports at 0170 [size=8]
	Region 3: I/O ports at 0374 [size=1]
	Region 4: I/O ports at 4000 [size=16]
	Kernel driver in use: pata_sis

00:02.7 Multimedia audio controller [0401]: Silicon Integrated Systems [SiS] AC'97 Sound Controller [1039:7012] (rev a0)
	Subsystem: Hewlett-Packard Company Device [103c:2a05]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32 (13000ns min, 2750ns max)
	Interrupt: pin C routed to IRQ 18
	Region 0: I/O ports at a000 [size=256]
	Region 1: I/O ports at a400 [size=128]
	Capabilities: [48] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: Intel ICH
	Kernel modules: snd-intel8x0

00:03.0 USB Controller [0c03]: Silicon Integrated Systems [SiS] USB 1.1 Controller [1039:7001] (rev 0f) (prog-if 10)
	Subsystem: Hewlett-Packard Company Device [103c:2a04]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+ INTx-
	Latency: 64 (20000ns max), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 20
	Region 0: Memory at e7004000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd

00:03.1 USB Controller [0c03]: Silicon Integrated Systems [SiS] USB 1.1 Controller [1039:7001] (rev 0f) (prog-if 10)
	Subsystem: Hewlett-Packard Company Device [103c:2a04]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+ INTx-
	Latency: 64 (20000ns max), Cache Line Size: 32 bytes
	Interrupt: pin B routed to IRQ 21
	Region 0: Memory at e7000000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd

00:03.2 USB Controller [0c03]: Silicon Integrated Systems [SiS] USB 1.1 Controller [1039:7001] (rev 0f) (prog-if 10)
	Subsystem: Hewlett-Packard Company Device [103c:2a04]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+ INTx-
	Latency: 64 (20000ns max), Cache Line Size: 32 bytes
	Interrupt: pin C routed to IRQ 22
	Region 0: Memory at e7001000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd

00:03.3 USB Controller [0c03]: Silicon Integrated Systems [SiS] USB 2.0 Controller [1039:7002] (prog-if 20)
	Subsystem: Hewlett-Packard Company Device [103c:2a04]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32 (20000ns max)
	Interrupt: pin D routed to IRQ 23
	Region 0: Memory at e7002000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: ehci_hcd

00:04.0 Ethernet controller [0200]: Silicon Integrated Systems [SiS] SiS900 PCI Fast Ethernet [1039:0900] (rev 90)
	Subsystem: Hewlett-Packard Company Device [103c:2a04]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32 (13000ns min, 2750ns max)
	Interrupt: pin A routed to IRQ 19
	Region 0: I/O ports at a800 [size=256]
	Region 1: Memory at e7003000 (32-bit, non-prefetchable) [size=4K]
	[virtual] Expansion ROM at 20000000 [disabled] [size=128K]
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: sis900
	Kernel modules: sis900

00:05.0 IDE interface [0101]: Silicon Integrated Systems [SiS] RAID bus controller 180 SATA/PATA  [SiS] [1039:0180] (rev 01) (prog-if 85 [Master SecO PriO])
	Subsystem: Hewlett-Packard Company Device [103c:2a04]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32
	Interrupt: pin A routed to IRQ 17
	Region 0: I/O ports at ac00 [size=8]
	Region 1: I/O ports at b000 [size=4]
	Region 2: I/O ports at b400 [size=8]
	Region 3: I/O ports at b800 [size=4]
	Region 4: I/O ports at bc00 [size=16]
	Region 5: I/O ports at c000 [size=128]
	Capabilities: [58] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: sata_sis

00:0a.0 Communication controller [0780]: Agere Systems V.92 56K WinModem [11c1:048c] (rev 03)
	Subsystem: Agere Systems Device [11c1:044c]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32 (63000ns min, 3500ns max)
	Interrupt: pin A routed to IRQ 255
	Region 0: Memory at e7005000 (32-bit, non-prefetchable) [size=256]
	Region 1: I/O ports at c400 [size=8]
	Region 2: I/O ports at c800 [size=256]
	Capabilities: [f8] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=160mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0b.0 FireWire (IEEE 1394) [0c00]: VIA Technologies, Inc. VT6306 Fire II IEEE 1394 OHCI Link Layer Controller [1106:3044] (rev 80) (prog-if 10)
	Subsystem: Device [0003:000f]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32 (8000ns max), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at e7006000 (32-bit, non-prefetchable) [size=2K]
	Region 1: I/O ports at cc00 [size=128]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: ohci1394
	Kernel modules: firewire-ohci, ohci1394

00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Capabilities: [80] HyperTransport: Host or Secondary Interface
		!!! Possibly incomplete decoding
		Command: WarmRst+ DblEnd-
		Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
		Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=8bit
		Revision ID: 1.02

00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Kernel driver in use: k8temp
	Kernel modules: k8temp

01:00.0 VGA compatible controller [0300]: ATI Technologies Inc RV530 [Radeon X1600] [1002:71c2]
	Subsystem: ATI Technologies Inc Device [1002:030b]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32 (2000ns min), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at d0000000 (64-bit, prefetchable) [size=256M]
	Region 2: Memory at e5000000 (64-bit, non-prefetchable) [size=64K]
	Region 4: I/O ports at 9000 [size=256]
	[virtual] Expansion ROM at e4000000 [disabled] [size=128K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] AGP version 3.0
		Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
		Command: RQ=32 ArqSz=2 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
	Capabilities: [80] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
		Address: 0000000000000000  Data: 0000
	Kernel modules: radeon

01:00.1 Display controller [0380]: ATI Technologies Inc RV530 [Radeon X1600] (Secondary) [1002:71e2]
	Subsystem: ATI Technologies Inc Device [1002:030a]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Region 0: Memory at e5010000 (64-bit, non-prefetchable) [disabled] [size=64K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-