[   13.422636] ppdev: user-space parallel port driver
[   13.668117] cfg80211: Calling CRDA to update world regulatory domain
[   13.893871] cfg80211: World regulatory domain updated:
[   13.893875] 	(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.893879] 	(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.893882] 	(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.893886] 	(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.893889] 	(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.893892] 	(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   15.183378] rt61pci 0000:03:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[   15.225675] phy0: Selected rate control algorithm 'minstrel'
[   15.226754] Registered led device: rt61pci-phy0::radio
[   15.226789] Registered led device: rt61pci-phy0::assoc
[   15.264650] rt61pci 0000:03:02.0: firmware: requesting rt2561s.bin
[   16.145397] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   18.213139] [drm] Setting GART location based on new memory map
[   18.214558] [drm] Loading R300 Microcode
[   18.214598] [drm] Num pipes: 1
[   18.214606] [drm] writeback test succeeded in 1 usecs
[   24.916022] usb 1-3: reset high speed USB device using ehci_hcd and address 3
[   32.920027] usb 1-3: reset high speed USB device using ehci_hcd and address 3
[   37.886521] wlan0: direct probe to AP e2:48:b3:51:4b:f8 try 1
[   37.888451] wlan0 direct probe responded
[   37.888458] wlan0: authenticate with AP e2:48:b3:51:4b:f8
[   37.890294] wlan0: authenticated
[   37.890300] wlan0: associate with AP e2:48:b3:51:4b:f8
[   37.893814] wlan0: RX AssocResp from e2:48:b3:51:4b:f8 (capab=0x411 status=0 aid=3)
[   37.893820] wlan0: associated
[   37.894815] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   39.511193] UDF-fs: No VRS found
[   39.511199] UDF-fs: No partition found (1)
[   39.591750] ISO 9660 Extensions: Microsoft Joliet Level 3
[   39.596875] ISOFS: changing to secondary root
[   40.928046] usb 1-3: reset high speed USB device using ehci_hcd and address 3
[   48.000016] wlan0: no IPv6 routers present
[   48.932043] usb 1-3: reset high speed USB device using ehci_hcd and address 3
[   56.916036] usb 1-3: reset high speed USB device using ehci_hcd and address 3
[   64.932024] usb 1-3: reset high speed USB device using ehci_hcd and address 3
[   72.917986] usb 1-3: reset high speed USB device using ehci_hcd and address 3
[   80.935772] usb 1-3: reset high speed USB device using ehci_hcd and address 3
[   81.171232] CPU0 attaching NULL sched-domain.
[   81.171238] CPU1 attaching NULL sched-domain.
[   81.180079] CPU0 attaching sched-domain:
[   81.180084]  domain 0: span 0-1 level SIBLING
[   81.180089]   groups: 0 1
[   81.180095]   domain 1: span 0-1 level MC
[   81.180099]    groups: 0-1 (__cpu_power = 2048)
[   81.180110] CPU1 attaching sched-domain:
[   81.180113]  domain 0: span 0-1 level SIBLING
[   81.180116]   groups: 1 0
[   81.180121]   domain 1: span 0-1 level MC
[   81.180124]    groups: 0-1 (__cpu_power = 2048)