Error: command ['sh', '-c', 'dmesg | comm -13 /var/log/dmesg -'] failed with exit code 1: [ 15.341107] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both [ 15.341260] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 17.032518] usb 2-1: device descriptor read/64, error -110 [ 18.881998] udev: starting version 147 [ 24.867190] ip_tables: (C) 2000-2006 Netfilter Core Team [ 25.544007] eth0: no IPv6 routers present [ 26.677524] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 26.677544] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 27.496694] hda_codec: Unknown model for ALC888, trying auto-probe from BIOS... [ 27.496869] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input4 [ 27.535110] nvidia: module license 'NVIDIA' taints kernel. [ 27.535114] Disabling lock debugging due to kernel taint [ 27.787742] intel_rng: FWH not detected [ 27.787823] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 27.787830] nvidia 0000:01:00.0: setting latency timer to 64 [ 27.787956] NVRM: loading NVIDIA UNIX x86 Kernel Module 185.18.36 Fri Aug 14 17:18:04 PDT 2009 [ 28.015130] parport_pc 00:08: reported by Plug and Play ACPI [ 28.015182] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA] [ 28.020248] lp: driver loaded but no devices found [ 28.023472] ppdev: user-space parallel port driver [ 28.072090] cfg80211: Calling CRDA to update world regulatory domain [ 28.112685] lp0: using parport0 (interrupt-driven). [ 28.801919] cfg80211: World regulatory domain updated: [ 28.801922] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 28.801925] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 28.801927] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 28.801929] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 28.801931] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 28.801933] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 30.424746] b43-phy0: Broadcom 4318 WLAN found (core revision 9) [ 30.499050] phy0: Selected rate control algorithm 'minstrel' [ 30.499626] Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ] [ 30.760033] b43 ssb0:0: firmware: requesting b43/ucode5.fw [ 30.810247] b43 ssb0:0: firmware: requesting b43/pcm5.fw [ 30.814350] b43 ssb0:0: firmware: requesting b43/b0g0initvals5.fw [ 30.818550] b43 ssb0:0: firmware: requesting b43/b0g0bsinitvals5.fw [ 30.940030] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10) [ 30.984383] Registered led device: b43-phy0::tx [ 30.984399] Registered led device: b43-phy0::rx [ 30.984417] Registered led device: b43-phy0::assoc [ 30.984432] Registered led device: b43-phy0::radio [ 31.008406] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 32.248580] usb 2-1: device descriptor read/64, error -110 [ 32.464522] usb 2-1: new full speed USB device using uhci_hcd and address 3 [ 36.545310] CPU0 attaching NULL sched-domain. [ 36.545314] CPU1 attaching NULL sched-domain. [ 36.564072] CPU0 attaching sched-domain: [ 36.564075] domain 0: span 0-1 level MC [ 36.564077] groups: 0 1 [ 36.564080] domain 1: span 0-1 level CPU [ 36.564082] groups: 0-1 (__cpu_power = 2048) [ 36.564086] CPU1 attaching sched-domain: [ 36.564088] domain 0: span 0-1 level MC [ 36.564089] groups: 1 0 [ 36.564092] domain 1: span 0-1 level CPU [ 36.564094] groups: 0-1 (__cpu_power = 2048) [ 47.576019] usb 2-1: device descriptor read/64, error -110 [ 62.792018] usb 2-1: device descriptor read/64, error -110 [ 63.008016] usb 2-1: new full speed USB device using uhci_hcd and address 4 [ 73.416017] usb 2-1: device not accepting address 4, error -110 [ 73.528013] usb 2-1: new full speed USB device using uhci_hcd and address 5 [ 83.936013] usb 2-1: device not accepting address 5, error -110 [ 83.936032] hub 2-0:1.0: unable to enumerate USB device on port 1 [ 84.176014] usb 4-2: new low speed USB device using uhci_hcd and address 2 [ 84.331125] usb 4-2: configuration #1 chosen from 1 choice [ 84.373172] usbcore: registered new interface driver hiddev [ 84.387244] input: HID 04b4:0033 as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input5 [ 84.387314] generic-usb 0003:04B4:0033.0001: input,hidraw0: USB HID v1.00 Mouse [HID 04b4:0033] on usb-0000:00:1d.2-2/input0 [ 84.387327] usbcore: registered new interface driver usbhid [ 84.387329] usbhid: v2.6:USB HID core driver [ 84.446167] CPU0 attaching NULL sched-domain. [ 84.446172] CPU1 attaching NULL sched-domain. [ 84.456581] CPU0 attaching sched-domain: [ 84.456584] domain 0: span 0-1 level MC [ 84.456586] groups: 0 1 [ 84.456590] CPU1 attaching sched-domain: [ 84.456591] domain 0: span 0-1 level MC [ 84.456593] groups: 1 0 comm: file 2 is not in sorted order [ 104.724257] wlan0: direct probe to AP 00:18:39:5b:ba:ab try 1 [ 104.732513] wlan0 direct probe responded [ 104.732517] wlan0: authenticate with AP 00:18:39:5b:ba:ab [ 104.736047] wlan0: authenticated [ 104.736052] wlan0: associate with AP 00:18:39:5b:ba:ab [ 104.739874] wlan0: RX AssocResp from 00:18:39:5b:ba:ab (capab=0x471 status=0 aid=1) [ 104.739878] wlan0: associated [ 104.740491] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 112.274721] EXT4-fs (sdb1): barriers enabled [ 112.312969] kjournald2 starting: pid 5325, dev sdb1:8, commit interval 5 seconds [ 112.313440] EXT4-fs (sdb1): internal journal on sdb1:8 [ 112.313447] EXT4-fs (sdb1): delayed allocation enabled [ 112.313452] EXT4-fs: file extents enabled [ 112.314816] EXT4-fs: mballoc enabled [ 112.314828] EXT4-fs (sdb1): mounted filesystem with ordered data mode [ 115.156008] wlan0: no IPv6 routers present [ 123.276983] wlan0: disassociating by local choice (reason=3) [ 123.348525] wlan0: deauthenticating by local choice (reason=3) [ 1102.011616] CPU0 attaching NULL sched-domain. [ 1102.011620] CPU1 attaching NULL sched-domain. [ 1102.024066] CPU0 attaching sched-domain: [ 1102.024070] domain 0: span 0-1 level MC [ 1102.024072] groups: 0 1 [ 1102.024076] CPU1 attaching sched-domain: [ 1102.024078] domain 0: span 0-1 level MC [ 1102.024080] groups: 1 0 [ 1102.356018] sky2 eth0: disabling interface [ 1103.592986] PM: Syncing filesystems ... done. [ 1103.600441] PM: Preparing system for mem sleep [ 1103.600447] Freezing user space processes ... (elapsed 0.00 seconds) done. [ 1103.601214] Freezing remaining freezable tasks ... (elapsed 0.09 seconds) done. [ 1103.692525] PM: Entering mem sleep [ 1103.692536] Suspending console(s) (use no_console_suspend to debug) [ 1103.764029] sd 2:0:0:0: [sda] Stopping disk [ 1104.248114] ACPI handle has no context! [ 1104.248321] parport_pc 00:08: disabled [ 1104.248381] ACPI handle has no context! [ 1104.264054] b43-pci-bridge 0000:04:09.0: PCI INT A disabled [ 1104.264118] ACPI handle has no context! [ 1104.264123] sky2 0000:03:00.0: PME# disabled [ 1104.264129] ACPI handle has no context! [ 1104.313091] ata_piix 0000:00:1f.2: PCI INT B disabled [ 1104.328070] ata2: port disabled. ignoring. [ 1104.328105] ata_piix 0000:00:1f.1: PCI INT A disabled [ 1104.328113] ehci_hcd 0000:00:1d.7: PCI INT A disabled [ 1104.328119] uhci_hcd 0000:00:1d.3: PCI INT D disabled [ 1104.328125] uhci_hcd 0000:00:1d.2: PCI INT C disabled [ 1104.328130] uhci_hcd 0000:00:1d.1: PCI INT B disabled [ 1104.328135] uhci_hcd 0000:00:1d.0: PCI INT A disabled [ 1104.328156] HDA Intel 0000:00:1b.0: PCI INT A disabled [ 1104.344070] PM: suspend devices took 0.652 seconds [ 1104.344243] ehci_hcd 0000:00:1d.7: PME# disabled [ 1104.360410] ACPI: Preparing to enter system sleep state S3 [ 1104.360901] Disabling non-boot CPUs ... [ 1104.464015] CPU 1 is now offline [ 1104.464019] SMP alternatives: switching to UP code [ 1104.469008] CPU0 attaching NULL sched-domain. [ 1104.469010] CPU1 attaching NULL sched-domain. [ 1104.469015] CPU0 attaching NULL sched-domain. [ 1104.469148] CPU1 is down [ 1104.469155] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 [ 1104.469155] Back to C! [ 1104.469155] Enabling non-boot CPUs ... [ 1104.469155] SMP alternatives: switching to SMP code [ 1104.474041] Booting processor 1 APIC 0x1 ip 0x6000 [ 1104.468900] Initializing CPU#1 [ 1104.468900] Calibrating delay using timer specific routine.. 5004.54 BogoMIPS (lpj=10009084) [ 1104.468900] CPU: L1 I cache: 32K, L1 D cache: 32K [ 1104.468900] CPU: L2 cache: 2048K [ 1104.468900] CPU: Physical Processor ID: 0 [ 1104.468900] CPU: Processor Core ID: 1 [ 1104.468900] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106 [ 1104.565449] CPU1: Intel Pentium(R) Dual-Core CPU E5200 @ 2.50GHz stepping 06 [ 1104.565461] checking TSC synchronization [CPU#0 -> CPU#1]: passed. [ 1104.585517] CPU0 attaching NULL sched-domain. [ 1104.588511] Switched to high resolution mode on CPU 1 [ 1104.600017] CPU0 attaching sched-domain: [ 1104.600021] domain 0: span 0-1 level MC [ 1104.600025] groups: 0 1 [ 1104.600032] CPU1 attaching sched-domain: [ 1104.600035] domain 0: span 0-1 level MC [ 1104.600038] groups: 1 0 [ 1104.600515] CPU1 is up [ 1104.600519] ACPI: Waking up from system sleep state S3 [ 1104.600899] pcieport-driver 0000:00:01.0: restoring config space at offset 0x1 (was 0x100007, writing 0x100407) [ 1104.600923] HDA Intel 0000:00:1b.0: restoring config space at offset 0xf (was 0x100, writing 0x105) [ 1104.600936] HDA Intel 0000:00:1b.0: restoring config space at offset 0x4 (was 0x4, writing 0xfdff8004) [ 1104.600939] HDA Intel 0000:00:1b.0: restoring config space at offset 0x3 (was 0x0, writing 0x10) [ 1104.600944] HDA Intel 0000:00:1b.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100002) [ 1104.600976] pcieport-driver 0000:00:1c.0: restoring config space at offset 0x1 (was 0x100007, writing 0x100407) [ 1104.601017] pcieport-driver 0000:00:1c.1: restoring config space at offset 0x1 (was 0x100007, writing 0x100407) [ 1104.616025] ehci_hcd 0000:00:1d.7: restoring config space at offset 0xf (was 0x100, writing 0x10a) [ 1104.616050] ehci_hcd 0000:00:1d.7: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900002) [ 1104.616072] ehci_hcd 0000:00:1d.7: PME# disabled [ 1104.616135] ata_piix 0000:00:1f.1: restoring config space at offset 0x8 (was 0xf001, writing 0xfb01) [ 1104.632045] ata_piix 0000:00:1f.2: restoring config space at offset 0x1 (was 0x2b00001, writing 0x2b00005) [ 1104.632096] nvidia 0000:01:00.0: restoring config space at offset 0xf (was 0x100, writing 0x105) [ 1104.632103] nvidia 0000:01:00.0: restoring config space at offset 0x9 (was 0x1, writing 0xbf01) [ 1104.632107] nvidia 0000:01:00.0: restoring config space at offset 0x7 (was 0x4, writing 0xf8000004) [ 1104.632111] nvidia 0000:01:00.0: restoring config space at offset 0x5 (was 0xc, writing 0xd000000c) [ 1104.632115] nvidia 0000:01:00.0: restoring config space at offset 0x4 (was 0x0, writing 0xfa000000) [ 1104.632120] nvidia 0000:01:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100007) [ 1104.632159] sky2 0000:03:00.0: restoring config space at offset 0xf (was 0x100, writing 0x10b) [ 1104.632176] sky2 0000:03:00.0: restoring config space at offset 0x6 (was 0x1, writing 0xce01) [ 1104.632182] sky2 0000:03:00.0: restoring config space at offset 0x4 (was 0x4, writing 0xfddfc004) [ 1104.632187] sky2 0000:03:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x10) [ 1104.632193] sky2 0000:03:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100407) [ 1104.632245] b43-pci-bridge 0000:04:09.0: restoring config space at offset 0x1 (was 0x2, writing 0x6) [ 1104.648024] ohci1394 0000:04:0a.0: restoring config space at offset 0xf (was 0x4020100, writing 0x4020103) [ 1104.648047] ohci1394 0000:04:0a.0: restoring config space at offset 0x3 (was 0x0, writing 0x2010) [ 1104.648055] ohci1394 0000:04:0a.0: restoring config space at offset 0x1 (was 0x2100000, writing 0x2100006) [ 1104.648257] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1104.648262] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 1104.648278] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 1104.648283] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 1104.648303] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 1104.648308] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 1104.648318] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 1104.648323] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 1104.648340] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 [ 1104.648345] uhci_hcd 0000:00:1d.3: setting latency timer to 64 [ 1104.648370] ehci_hcd 0000:00:1d.7: PME# disabled [ 1104.648374] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 1104.648379] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 1104.648383] usb usb1: root hub lost power or was reset [ 1104.652265] ehci_hcd 0000:00:1d.7: debug port 1 [ 1104.652270] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported [ 1104.652277] pci 0000:00:1e.0: setting latency timer to 64 [ 1104.652284] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 1104.652288] ata_piix 0000:00:1f.1: setting latency timer to 64 [ 1104.652300] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 1104.652303] ata_piix 0000:00:1f.2: setting latency timer to 64 [ 1104.681524] ata2: port disabled. ignoring. [ 1104.967327] ata3.01: ACPI cmd ef/03:45:00:00:00:b0 filtered out [ 1104.967330] ata3.01: ACPI cmd ef/03:45:00:00:00:b0 filtered out [ 1104.967332] ata3.01: ACPI cmd ef/03:0c:00:00:00:b0 filtered out [ 1104.967537] sky2 0000:03:00.0: PME# disabled [ 1104.967581] b43-pci-bridge 0000:04:09.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1104.972191] ata3.00: ACPI cmd ef/03:45:00:00:00:a0 filtered out [ 1104.972193] ata3.00: ACPI cmd ef/03:45:00:00:00:a0 filtered out [ 1104.972196] ata3.00: ACPI cmd ef/03:0c:00:00:00:a0 filtered out [ 1104.988206] ata3.00: configured for UDMA/100 [ 1105.004209] ata3.01: configured for UDMA/100 [ 1105.040036] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[fdaff000-fdaff7ff] Max Packet=[2048] IR/IT contexts=[4/8] [ 1105.040952] parport_pc 00:08: activated [ 1105.540070] sd 2:0:0:0: [sda] Starting disk [ 1105.668016] usb 1-5: reset high speed USB device using ehci_hcd and address 3 [ 1105.912015] usb 1-7: reset high speed USB device using ehci_hcd and address 5 [ 1106.304013] usb 4-2: reset low speed USB device using uhci_hcd and address 2 [ 1106.611208] PM: resume devices took 1.960 seconds [ 1106.611226] PM: Finishing wakeup. [ 1106.611227] Restarting tasks ... done. [ 1106.822824] sky2 eth0: enabling interface [ 1106.822986] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 1106.872021] usb 2-1: new full speed USB device using uhci_hcd and address 6 [ 1107.159659] CPU0 attaching NULL sched-domain. [ 1107.159665] CPU1 attaching NULL sched-domain. [ 1107.172080] CPU0 attaching sched-domain: [ 1107.172083] domain 0: span 0-1 level MC [ 1107.172086] groups: 0 1 [ 1107.172089] domain 1: span 0-1 level CPU [ 1107.172091] groups: 0-1 (__cpu_power = 2048) [ 1107.172096] CPU1 attaching sched-domain: [ 1107.172098] domain 0: span 0-1 level MC [ 1107.172100] groups: 1 0 [ 1107.172102] domain 1: span 0-1 level CPU [ 1107.172104] groups: 0-1 (__cpu_power = 2048) [ 1108.506158] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both [ 1108.506316] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 1119.132008] eth0: no IPv6 routers present [ 1121.984015] usb 2-1: device descriptor read/64, error -110 [ 1137.200025] usb 2-1: device descriptor read/64, error -110 [ 1137.416027] usb 2-1: new full speed USB device using uhci_hcd and address 7 [ 1152.528016] usb 2-1: device descriptor read/64, error -110 [ 1167.744022] usb 2-1: device descriptor read/64, error -110 [ 1167.960015] usb 2-1: new full speed USB device using uhci_hcd and address 8 [ 1178.368010] usb 2-1: device not accepting address 8, error -110 [ 1178.480014] usb 2-1: new full speed USB device using uhci_hcd and address 9 [ 1188.888014] usb 2-1: device not accepting address 9, error -110 [ 1188.888037] hub 2-0:1.0: unable to enumerate USB device on port 1 [ 1584.968035] usb 2-1: new full speed USB device using uhci_hcd and address 10