tg3 driver freezes network randomly
Affects | Status | Importance | Assigned to | Milestone | |
---|---|---|---|---|---|
linux (Ubuntu) |
Incomplete
|
Undecided
|
Unassigned |
Bug Description
Binary package hint: linux-image-
Ubuntu 8.04
Package: linux-image-
The network randomly freezes with in-kernel tg3 driver. Sometimes it can be fixed by reloading the tg3 driver by "rmmod tg3 && modprobe tg3", otherwise its reboot time. Kernel is loaded with default boot parameters (ie. no noapic/
relevant dmesg snip:
[ 1946.559331] tg3: tg3_abort_hw timed out for eth0, TX_MODE_ENABLE will not clear MAC_TX_
[ 1947.361422] tg3: eth0: No firmware running.
[ 1951.487984] BUG: soft lockup - CPU#0 stuck for 11s! [ifconfig:9162]
[ 1951.487990]
[ 1951.487993] Pid: 9162, comm: ifconfig Tainted: P (2.6.24-17-generic #1)
[ 1951.487997] EIP: 0060:[<c021a1a7>] EFLAGS: 00200297 CPU: 0
[ 1951.488004] EIP is at delay_tsc+0x27/0x50
[ 1951.488006] EAX: f603deb3 EBX: 0000038a ECX: 00000000 EDX: 0000038a
[ 1951.488009] ESI: f603deaa EDI: ee573e18 EBP: f603b98d ESP: ee573dcc
[ 1951.488011] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[ 1951.488013] CR0: 8005003b CR2: 0805b1e0 CR3: 330ac000 CR4: 00000690
[ 1951.488018] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[ 1951.488021] DR6: ffff0ff0 DR7: 00000400
[ 1951.488054] [<c021a146>] __delay+0x6/0x10
[ 1951.488062] [<f888d245>] tg3_readphy+
[ 1951.488095] [<f888e8e7>] tg3_setup_
[ 1951.488115] [<c01cbee8>] remove_
[ 1951.488157] [<f888f505>] tg3_setup_
[ 1951.488177] [<c029bae3>] pci_read+0x33/0x40
[ 1951.488203] [<c02216fe>] pci_bus_
[ 1951.488240] [<f8890a1c>] tg3_set_
[ 1951.488290] [<f889b062>] tg3_close+
[ 1951.488318] [<c02a991c>] dev_close+0x3c/0x60
[ 1951.488326] [<c02a9771>] dev_change_
[ 1951.488337] [<c02a7db4>] __dev_get_
[ 1951.488355] [<c02f44e5>] devinet_
[ 1951.488373] [<c02aa8a2>] dev_ioctl+
[ 1951.488462] [<c029c6df>] sock_ioctl+
[ 1951.488475] [<c029c610>] sock_ioctl+
[ 1951.488489] [<c019dfab>] do_ioctl+0x2b/0x90
[ 1951.488514] [<c019e23e>] vfs_ioctl+
[ 1951.488540] [<c019e316>] sys_ioctl+0x56/0x70
[ 1951.488560] [<c01043c2>] sysenter_
[ 1951.488630] =======
[ 1952.590441] tg3: eth0: Link is down.
full lspci -vvv:
00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 10)
Subsystem: Hewlett-Packard Company Unknown device 3009
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 3: Memory at <ignored> (64-bit, non-prefetchable)
00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 99
Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fda00000-fdafffff
Prefetchable memory behind bridge: 00000000c800000
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [44] HyperTransport: MSI Mapping
Capabilities: [b0] Subsystem: ATI Technologies Inc RS480 PCI Bridge
00:05.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fde00000-fdefffff
Prefetchable memory behind bridge: 00000000fdb0000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 2
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [b0] Subsystem: ATI Technologies Inc Unknown device 5950
Capabilities: [b8] HyperTransport: MSI Mapping
00:12.0 IDE interface: ATI Technologies Inc IXP SB400 Serial ATA Controller (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Hewlett-Packard Company Unknown device 3009
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at fc00 [size=8]
Region 1: I/O ports at f800 [size=4]
Region 2: I/O ports at f400 [size=8]
Region 3: I/O ports at f000 [size=4]
Region 4: I/O ports at ec00 [size=16]
Region 5: Memory at fe02f000 (32-bit, non-prefetchable) [size=512]
[virtual] Expansion ROM at d8000000 [disabled] [size=512K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Unknown device 3009
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Unknown device 3009
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Unknown device 3009
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 11)
Subsystem: Hewlett-Packard Company Unknown device 3009
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Region 0: I/O ports at 0500 [size=16]
Region 1: Memory at fe02b000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [b0] HyperTransport: MSI Mapping
00:14.1 IDE interface: ATI Technologies Inc IXP SB400 IDE Controller (prog-if 82 [Master PriP])
Subsystem: Hewlett-Packard Company Unknown device 3009
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at e400 [size=16]
Capabilities: [70] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge
Subsystem: Hewlett-Packard Company Unknown device 3009
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=03, subordinate=03, sec-latency=64
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fdd00000-fddfffff
Prefetchable memory behind bridge: fdc00000-fdcfffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
01:05.0 VGA compatible controller: ATI Technologies Inc RS480 [Radeon Xpress 200G Series] (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Unknown device 3009
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 255 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at cc00 [size=256]
Region 2: Memory at fdaf0000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at fda00000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:05.1 Display controller: ATI Technologies Inc Unknown device 5854
Subsystem: Hewlett-Packard Company Unknown device 3008
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Region 0: Memory at c8000000 (32-bit, prefetchable) [disabled] [size=128M]
Region 1: Memory at fdae0000 (32-bit, non-prefetchable) [disabled] [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5751 Gigabit Ethernet PCI Express (rev 20)
Subsystem: Hewlett-Packard Company Unknown device 3009
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fdef0000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 Enable-
Address: 0000020000280000 Data: 8000
Capabilities: [d0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <4us, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <4us, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
03:0a.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 22
Region 4: I/O ports at bc00 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
03:0a.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at b800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
03:0a.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 63) (prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fddff000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
03:0b.0 Multimedia audio controller: Creative Labs SB Audigy (rev 03)
Subsystem: Creative Labs SB0090 Audigy Player/OEM
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at b400 [size=32]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
03:0b.1 Input device controller: Creative Labs SB Audigy Game Port (rev 03)
Subsystem: Creative Labs SB Audigy MIDI/Game Port
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 0: I/O ports at b000 [size=8]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
03:0b.2 FireWire (IEEE 1394): Creative Labs SB Audigy FireWire Port (prog-if 10 [OHCI])
Subsystem: Creative Labs SB Audigy FireWire Port
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 21
Region 0: Memory at fddfe000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at fddf8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
Changed in linux: | |
status: | New → Confirmed |
I can confirm this issue ; Ubuntu 8.04 with the default latest updates (kernel 2.6.24-17-generic)
Happened twice so far at seemingly random moments. Suddenly no network connectivity whatsoever. rmmod && modprobe seems to remedy the problem.
DMESG: MODE=ffffffff 0x65/0x100 [tg3] copper_ phy+0x195/ 0xb80 [tg3] phy+0x225/ 0xed0 [tg3] read_config_ word+0x6e/ 0x90 power_state+ 0x4bc/0x920 [tg3] 0x102/0x120 [tg3] registered+ 0x7c/0x140 cpu+0x12/ 0x20 netdevice+ 0x8/0x50 netdev+ 0xf/0x20 one+0x2c/ 0x80 [tg3] remove+ 0x16/0x40 release_ driver+ 0x64/0xa0 detach+ 0xcb/0xd0 driver+ 0x73/0xa0 driver+ 0xe/0x70 module+ 0x112/0x190 fault+0x13f/ 0x730 0x180/0x1f0 past_esp+ 0x6b/0xa9 recvmsg+ 0x110/0x2d0 ======= ======= ==
[ 7169.894256] tg3: tg3_abort_hw timed out for eth0, TX_MODE_ENABLE will not clear MAC_TX_
[ 7171.623397] tg3: eth0: No firmware running.
[ 7180.250854] BUG: soft lockup - CPU#1 stuck for 11s! [rmmod:18573]
[ 7180.250863]
[ 7180.250866] Pid: 18573, comm: rmmod Tainted: P (2.6.24-17-generic #1)
[ 7180.250869] EIP: 0060:[<c021a1a7>] EFLAGS: 00200283 CPU: 1
[ 7180.250874] EIP is at delay_tsc+0x27/0x50
[ 7180.250877] EAX: 95f05cec EBX: 00000adf ECX: 00000000 EDX: 00000adf
[ 7180.250879] ESI: 95f05c9c EDI: ee553e30 EBP: 95f04040 ESP: ee553de4
[ 7180.250883] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[ 7180.250885] CR0: 8005003b CR2: b7f4c550 CR3: 1bc46000 CR4: 00000690
[ 7180.250888] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[ 7180.250890] DR6: ffff0ff0 DR7: 00000400
[ 7180.250921] [<c021a146>] __delay+0x6/0x10
[ 7180.250929] [<f88d3245>] tg3_readphy+
[ 7180.250947] [<f88d48f5>] tg3_setup_
[ 7180.250969] [<f88d5505>] tg3_setup_
[ 7180.250982] [<c029bae3>] pci_read+0x33/0x40
[ 7180.250995] [<c02216fe>] pci_bus_
[ 7180.251010] [<f88d6a1c>] tg3_set_
[ 7180.251031] [<f88e1062>] tg3_close+
[ 7180.251045] [<c02a991c>] dev_close+0x3c/0x60
[ 7180.251053] [<c02a99bc>] rollback_
[ 7180.251062] [<c0214392>] __next_
[ 7180.251069] [<c02a9a88>] unregister_
[ 7180.251078] [<c02a9adf>] unregister_
[ 7180.251087] [<f88deedc>] tg3_remove_
[ 7180.251102] [<c0227196>] pci_device_
[ 7180.251109] [<c0282344>] __device_
[ 7180.251121] [<c028289b>] driver_
[ 7180.251133] [<c0281e93>] bus_remove_
[ 7180.251143] [<c022726e>] pci_unregister_
[ 7180.251153] [<c01521a2>] sys_delete_
[ 7180.251163] [<c031ddbf>] do_page_
[ 7180.251173] [<c01804a0>] do_munmap+
[ 7180.251191] [<c01043c2>] sysenter_
[ 7180.251205] [<c0310000>] unix_dgram_
[ 7180.251218] =======
LSPCI:
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0- ,D1-,D2- ,D3hot+ ,D3cold+ )
Status: D0 PME-Enab...
09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5752 Gigabit Ethernet PCI Express (rev 02)
Subsystem: Dell Unknown device 01cc
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 219
Region 0: Memory at efcf0000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]