Ubuntu

[IdeaPad U310, Conexant CX20590, Mic, Internal] No sound at all

Reported by Taras on 2013-09-19
6
This bug affects 1 person
Affects Status Importance Assigned to Milestone
linux (Ubuntu)
Medium
Unassigned

Bug Description

The sound worked fine under ubuntu 12.10.

Alsamixer maxed out, nothing muted.

Running the command arecord test.wav produces no sound, no sound in skype.

 Attempted posted work arounds by editing /etc/modprobe.d/alsa-base.conf with snd-hda-intel model=basic, snd-hda-intel model=default, snd-hda-intel model=azus nothing helped.

Audio Card Data
output from: lspci -v | grep -A7 -i "audio"
00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04)
 Subsystem: Lenovo Device 3977
 Flags: bus master, fast devsel, latency 0, IRQ 45
 Memory at f0610000 (64-bit, non-prefetchable) [size=16K]
 Capabilities: [50] Power Management version 2
 Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
 Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00
 Capabilities: [100] Virtual Channel

output from: cat /proc/asound/card0/codec*
Codec: Conexant CX20590
Address: 0
AFG Function Id: 0x1 (unsol 1)
Vendor Id: 0x14f1506e
Subsystem Id: 0x17aa4009
Revision Id: 0x100003
No Modem Function Group found
Default PCM:
    rates [0x160]: 44100 48000 96000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
State of AFG node 0x01:
  Power states: D0 D1 D2 D3 D3cold CLKSTOP EPSS
  Power: setting=D0, actual=D0
GPIO: io=4, o=0, i=0, unsolicited=1, wake=0
  IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
  IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
  IO[2]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
  IO[3]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
Node 0x10 [Audio Output] wcaps 0xc1d: Stereo Amp-Out R/L
  Control: name="Headphone Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Control: name="Headphone Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Device: name="CX20590 Analog", type="Audio", device=0
  Amp-Out caps: ofs=0x4a, nsteps=0x4a, stepsize=0x03, mute=1
  Amp-Out vals: [0x4a 0x4a]
  Converter: stream=8, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states: D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
Node 0x11 [Audio Output] wcaps 0xc1d: Stereo Amp-Out R/L
  Control: name="Speaker Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Control: name="Speaker Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x4a, nsteps=0x4a, stepsize=0x03, mute=1
  Amp-Out vals: [0x4a 0x4a]
  Converter: stream=8, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states: D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
Node 0x12 [Audio Output] wcaps 0x611: Stereo Digital
  Converter: stream=0, channel=0
  Digital:
  Digital category: 0x0
  IEC Coding Type: 0x0
  PCM:
    rates [0x160]: 44100 48000 96000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3
  Power states: D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
Node 0x13 [Beep Generator Widget] wcaps 0x70000c: Mono Amp-Out
  Control: name="Beep Playback Volume", index=0, device=0
    ControlAmp: chs=1, dir=Out, idx=0, ofs=0
  Control: name="Beep Playback Switch", index=0, device=0
    ControlAmp: chs=1, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x07, nsteps=0x07, stepsize=0x0f, mute=0
  Amp-Out vals: [0x07]
Node 0x14 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L
  Control: name="Capture Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Control: name="Capture Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Device: name="CX20590 Analog", type="Audio", device=0
  Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=1
  Amp-In vals: [0x4b 0x4b] [0x80 0x80] [0x4b 0x4b] [0x80 0x80]
  Converter: stream=4, channel=0
  SDI-Select: 0
  PCM:
    rates [0x160]: 44100 48000 96000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states: D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 4
     0x17 0x18 0x23* 0x24
Node 0x15 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L
  Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=1
  Amp-In vals: [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a]
  Converter: stream=0, channel=0
  SDI-Select: 0
  PCM:
    rates [0x160]: 44100 48000 96000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states: D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 4
     0x17* 0x18 0x23 0x24
Node 0x16 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L
  Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=1
  Amp-In vals: [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a]
  Converter: stream=0, channel=0
  SDI-Select: 0
  PCM:
    rates [0x160]: 44100 48000 96000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states: D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 4
     0x17* 0x18 0x23 0x24
Node 0x17 [Audio Selector] wcaps 0x30050d: Stereo Amp-Out
  Control: name="Mic Boost Volume", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=0
  Amp-Out vals: [0x04 0x04]
  Power states: D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 4
     0x1a* 0x1b 0x1d 0x1e
Node 0x18 [Audio Selector] wcaps 0x30050d: Stereo Amp-Out
  Amp-Out caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=0
  Amp-Out vals: [0x00 0x00]
  Power states: D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 4
     0x1a* 0x1b 0x1d 0x1e
Node 0x19 [Pin Complex] wcaps 0x400581: Stereo
  Control: name="Headphone Jack", index=0, device=0
  Pincap 0x0000001c: OUT HP Detect
  Pin Default 0x04211040: [Jack] HP Out at Ext Right
    Conn = 1/8, Color = Black
    DefAssociation = 0x4, Sequence = 0x0
  Pin-ctls: 0xc0: OUT HP
  Unsolicited: tag=01, enabled=1
  Power states: D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 2
     0x10* 0x11
Node 0x1a [Pin Complex] wcaps 0x400481: Stereo
  Control: name="Mic Jack", index=0, device=0
  Pincap 0x00001324: IN Detect
    Vref caps: HIZ 50 80
  Pin Default 0x04a11030: [Jack] Mic at Ext Right
    Conn = 1/8, Color = Black
    DefAssociation = 0x3, Sequence = 0x0
  Pin-ctls: 0x24: IN VREF_80
  Unsolicited: tag=02, enabled=1
  Power states: D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
Node 0x1b [Pin Complex] wcaps 0x400581: Stereo
  Pincap 0x00011334: IN OUT EAPD Detect
    Vref caps: HIZ 50 80
  EAPD 0x2: EAPD
  Pin Default 0x400001f0: [N/A] Line Out at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x00: VREF_HIZ
  Unsolicited: tag=00, enabled=0
  Power states: D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 2
     0x10* 0x11
Node 0x1c [Pin Complex] wcaps 0x400581: Stereo
  Pincap 0x00000014: OUT Detect
  Pin Default 0x400001f0: [N/A] Line Out at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=00, enabled=0
  Power states: D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 2
     0x10* 0x11
Node 0x1d [Pin Complex] wcaps 0x400581: Stereo
  Pincap 0x00010034: IN OUT EAPD Detect
  EAPD 0x2: EAPD
  Pin Default 0x400001f0: [N/A] Line Out at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=00, enabled=0
  Power states: D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 2
     0x10* 0x11
Node 0x1e [Pin Complex] wcaps 0x400481: Stereo
  Pincap 0x00000024: IN Detect
  Pin Default 0x400001f0: [N/A] Line Out at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x00:
  Unsolicited: tag=00, enabled=0
  Power states: D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
Node 0x1f [Pin Complex] wcaps 0x400501: Stereo
  Control: name="Speaker Phantom Jack", index=0, device=0
  Pincap 0x00000010: OUT
  Pin Default 0x90170110: [Fixed] Speaker at Int N/A
    Conn = Analog, Color = Unknown
    DefAssociation = 0x1, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x40: OUT
  Power states: D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 2
     0x10 0x11*
Node 0x20 [Pin Complex] wcaps 0x400781: Stereo Digital
  Pincap 0x00000010: OUT
  Pin Default 0x400001f0: [N/A] Line Out at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x00:
  Unsolicited: tag=00, enabled=0
  Power states: D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x12
Node 0x21 [Audio Output] wcaps 0x611: Stereo Digital
  Converter: stream=0, channel=0
  Digital:
  Digital category: 0x0
  IEC Coding Type: 0x0
  PCM:
    rates [0x160]: 44100 48000 96000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3
  Power states: D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
Node 0x22 [Pin Complex] wcaps 0x400781: Stereo Digital
  Pincap 0x00000010: OUT
  Pin Default 0x400001f0: [N/A] Line Out at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x00:
  Unsolicited: tag=00, enabled=0
  Power states: D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x21
Node 0x23 [Pin Complex] wcaps 0x40040b: Stereo Amp-In
  Control: name="Internal Mic Boost Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Control: name="Internal Mic Phantom Jack", index=0, device=0
  Amp-In caps: ofs=0x00, nsteps=0x04, stepsize=0x2f, mute=0
  Amp-In vals: [0x04 0x04]
  Pincap 0x00000020: IN
  Pin Default 0x90a60150: [Fixed] Mic at Int N/A
    Conn = Digital, Color = Unknown
    DefAssociation = 0x5, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x20: IN
  Power states: D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
Node 0x24 [Audio Mixer] wcaps 0x20050b: Stereo Amp-In
  Amp-In caps: ofs=0x4a, nsteps=0x4a, stepsize=0x03, mute=1
  Amp-In vals: [0x00 0x00] [0x00 0x00]
  Power states: D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 2
     0x10 0x11
Node 0x25 [Vendor Defined Widget] wcaps 0xf00000: Mono
Codec: Intel PantherPoint HDMI
Address: 3
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x80862806
Subsystem Id: 0x80860101
Revision Id: 0x100000
No Modem Function Group found
Default PCM:
    rates [0x0]:
    bits [0x0]:
    formats [0x0]:
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
State of AFG node 0x01:
  Power states: D0 D3 CLKSTOP EPSS
  Power: setting=D0, actual=D0, Clock-stop-OK
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x02 [Audio Output] wcaps 0x6611: 8-Channels Digital
  Converter: stream=0, channel=0
  Digital: Enabled
  Digital category: 0x0
  IEC Coding Type: 0x0
  PCM:
    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0x1e]: 16 20 24 32
    formats [0x5]: PCM AC3
  Power states: D0 D3 EPSS
  Power: setting=D0, actual=D0
Node 0x03 [Audio Output] wcaps 0x6611: 8-Channels Digital
  Converter: stream=0, channel=0
  Digital: Enabled
  Digital category: 0x0
  IEC Coding Type: 0x0
  PCM:
    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0x1e]: 16 20 24 32
    formats [0x5]: PCM AC3
  Power states: D0 D3 EPSS
  Power: setting=D0, actual=D0
Node 0x04 [Audio Output] wcaps 0x6611: 8-Channels Digital
  Converter: stream=0, channel=0
  Digital: Enabled
  Digital category: 0x0
  IEC Coding Type: 0x0
  PCM:
    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0x1e]: 16 20 24 32
    formats [0x5]: PCM AC3
  Power states: D0 D3 EPSS
  Power: setting=D0, actual=D0
Node 0x05 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
  Control: name="HDMI/DP,pcm=3 Jack", index=0, device=0
  Control: name="IEC958 Playback Con Mask", index=0, device=0
  Control: name="IEC958 Playback Pro Mask", index=0, device=0
  Control: name="IEC958 Playback Default", index=0, device=0
  Control: name="IEC958 Playback Switch", index=0, device=0
  Control: name="ELD", index=0, device=3
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals: [0x00 0x00]
  Pincap 0x09000094: OUT Detect HBR HDMI DP
  Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
    Conn = Digital, Color = Unknown
    DefAssociation = 0x1, Sequence = 0x0
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=01, enabled=1
  Power states: D0 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x02
Node 0x06 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals: [0x00 0x80]
  Pincap 0x09000094: OUT Detect HBR HDMI DP
  Pin Default 0x58560020: [N/A] Digital Out at Int HDMI
    Conn = Digital, Color = Unknown
    DefAssociation = 0x2, Sequence = 0x0
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=00, enabled=0
  Power states: D0 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x03
Node 0x07 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals: [0x00 0x80]
  Pincap 0x09000094: OUT Detect HBR HDMI DP
  Pin Default 0x58560030: [N/A] Digital Out at Int HDMI
    Conn = Digital, Color = Unknown
    DefAssociation = 0x3, Sequence = 0x0
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=00, enabled=0
  Power states: D0 D3 EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x04
Node 0x08 [Vendor Defined Widget] wcaps 0xf00000: Mono

Suggestions for a fix?

ProblemType: Bug
DistroRelease: Ubuntu 13.10
Package: alsa-base 1.0.25+dfsg-0ubuntu4
ProcVersionSignature: Ubuntu 3.11.0-7.14-generic 3.11.1
Uname: Linux 3.11.0-7-generic x86_64
NonfreeKernelModules: wl
ApportVersion: 2.12.2-0ubuntu1
Architecture: amd64
AudioDevicesInUse:
 USER PID ACCESS COMMAND
 /dev/snd/controlC0: nini 1948 F.... pulseaudio
Date: Thu Sep 19 10:42:19 2013
InstallationDate: Installed on 2013-09-18 (1 days ago)
InstallationMedia: Ubuntu 13.10 "Saucy Salamander" - Alpha amd64 (20130916)
MarkForUpload: True
PackageArchitecture: all
SourcePackage: alsa-driver
Symptom: audio
Symptom_AlsaRecordingTest: ALSA recording test through plughw:PCH failed
Symptom_Card: Built-in Audio - HDA Intel PCH
Symptom_DevicesInUse:
 USER PID ACCESS COMMAND
 /dev/snd/controlC0: nini 1948 F.... pulseaudio
Symptom_Jack: Mic, Internal
Symptom_Type: No sound at all
Title: [IdeaPad U310, Conexant CX20590, Mic, Internal] No sound at all
UpgradeStatus: No upgrade log present (probably fresh install)
dmi.bios.date: 12/26/2012
dmi.bios.vendor: LENOVO
dmi.bios.version: 65CN21WW
dmi.board.asset.tag: Base Board Asset Tag
dmi.board.name: Lenovo
dmi.board.vendor: LENOVO
dmi.board.version: Lenovo U310
dmi.chassis.asset.tag: Asset Tag
dmi.chassis.type: 9
dmi.chassis.vendor: Intel Corporation
dmi.chassis.version: 0.1
dmi.modalias: dmi:bvnLENOVO:bvr65CN21WW:bd12/26/2012:svnLENOVO:pnIdeaPadU310:pvrLenovoU310:rvnLENOVO:rnLenovo:rvrLenovoU310:cvnIntelCorporation:ct9:cvr0.1:
dmi.product.name: IdeaPad U310
dmi.product.version: Lenovo U310
dmi.sys.vendor: LENOVO

Taras (tiras-dude) wrote :
Taras (tiras-dude) wrote :

Same situation with the update to Kernel 3.11.0-8

Raymond (superquad-vortex2) wrote :

when internal mic (0x23) is selected, the amp -in value from node 0x17 (mux) must be muted (similar to the value [0x80 0x80] from node 0x18 )

Node 0x14 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L
  Control: name="Capture Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Control: name="Capture Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Device: name="CX20590 Analog", type="Audio", device=0
  Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=1
  Amp-In vals: [0x4b 0x4b] [0x80 0x80] [0x4b 0x4b] [0x80 0x80]
  Converter: stream=4, channel=0
  SDI-Select: 0
  PCM:
    rates [0x160]: 44100 48000 96000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states: D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 4
     0x17 0x18 0x23* 0x24

Taras (tiras-dude) wrote :

Raymond, thanks for the info.

Can you please provide instruction on how to implement this.

David Henningsson (diwic) wrote :

Hi,

This looks to be the same as bug 1239392, even though the hardware is different, the symptom is the same.

affects: alsa-driver (Ubuntu) → linux (Ubuntu)
Changed in linux (Ubuntu):
status: New → In Progress
David Henningsson (diwic) wrote :

Upstream committed a fix for this today - will likely come to 13.10 in a month or two through a kernel update. If you don't want to wait that long, try https://wiki.ubuntu.com/Audio/UpgradingAlsa/DKMS - starting with tomorrow's build the fix should be in there too.

Changed in linux (Ubuntu):
status: In Progress → Fix Committed
Changed in linux (Ubuntu):
importance: Undecided → Medium
Launchpad Janitor (janitor) wrote :
Download full text (3.7 KiB)

This bug was fixed in the package linux - 3.12.0-1.3

---------------
linux (3.12.0-1.3) trusty; urgency=low

  [ Andy Whitcroft ]

  * [Config] arm64 -- add arch to the configuration handlers
  * [Config] arm64 -- add generic flavour
  * [Config] arm64 -- default config
  * [Config] arm64 -- fix up various FTBFS config options
  * SAUCE: arm64: export __copy_in_user to modules
  * [Config] arm64 -- disable ABI/module checks
  * [Config] arm64 -- enforcer -- add arm64 to the enforcer
  * [Config] arm64 -- enable udebs for arm64

  [ Colin Watson ]

  * [Config] Clean up various udeb Provides

  [ Paolo Pisati ]

  * [Config] AHCI_IMX=y
  * [Config] build imx*-wandboard dtbs

  [ Serge Hallyn ]

  * SAUCE: device_cgroup: remove can_attach

  [ Tim Gardner ]

  * rebase to v3.12-rc7
  * SAUCE: KVM: Fix modprobe failure for kvm_intel/kvm_amd
  * Release tracker
    - LP: #1245932

  [ Upstream Kernel Changes ]

  * rebase to v3.12-rc7
    - LP: #1180881
    - LP: #1180881
    - LP: #1217957

linux (3.12.0-0.2) trusty; urgency=low

  [ Andy Whitcroft ]

  * Revert "SAUCE: (no-up) scsi: hyper-v storage -- mark as preferring READ
    CAPACITY (16) at SPC-2"
  * Revert "SAUCE: (no-up) scsi: hyper-v storage -- mark as VPD capable at
    SPC-2"
  * Revert "SAUCE: (no-up) scsi: add scsi device flag to request READ
    CAPACITY (16) be preferred"
  * Revert "SAUCE: (no-up) scsi: add scsi device flag to request VPD pages
    be used at SPC-2"
  * Revert "overlayfs: Update to v19"
  * Revert "ubuntu: overlayfs v18 -- -- overlayfs: implement show_options"
  * Revert "ubuntu: overlayfs v18 -- -- overlayfs: add statfs support"
  * Revert "ubuntu: overlayfs v18 -- -- overlay filesystem"
  * Revert "ubuntu: overlayfs v18 -- -- vfs: introduce
    clone_private_mount()"
  * Revert "ubuntu: overlayfs v18 -- -- vfs: export do_splice_direct() to
    modules"
  * Revert "ubuntu: overlayfs v18 -- -- overlay: overlay filesystem
    documentation"
  * ubuntu: overlayfs v20 -- overlayfs: add statfs support
  * [Config] fix linux-libc-dev generation for arm64
  * [Config] fix linux-libc-dev generation for x32
  * [Config] add linux-libc-dev generation for ppc64el

  [ Erez Zadok ]

  * ubuntu: overlayfs v20 -- overlayfs: implement show_options

  [ Miklos Szeredi ]

  * ubuntu: overlayfs v20 -- vfs: add i_op->dentry_open()
  * ubuntu: overlayfs v20 -- vfs: export do_splice_direct() to modules
  * ubuntu: overlayfs v20 -- vfs: export __inode_permission() to modules
  * ubuntu: overlayfs v20 -- vfs: introduce clone_private_mount()
  * ubuntu: overlayfs v20 -- overlay filesystem
  * ubuntu: overlayfs v20 -- fs: limit filesystem stacking depth

  [ Neil Brown ]

  * ubuntu: overlayfs v20 -- overlay: overlay filesystem documentation

  [ Paolo Pisati ]

  * [Config] arm: VIRTIO_[BLK|NET|MMIO]=y

  [ Seth Forshee ]

  * SAUCE: (no-up) ACPI: Disable Windows 8 compatibility for some Lenovo
    ThinkPads
    - LP: #1183856

  [ Tim Gardner ]

  * [Config] CONFIG_CRYPTO_CRCT10DIF=y, CONFIG_CRYPTO_CRCT10DIF_PCLMUL=m
  * rebase to v3.12-rc2
  * updateconfigs
  * [Config] disable CONFIG_FB_VESA enforcer check
  * [Config] Disable lttng for FTBS
  * rebase to v3.12-rc3
  * rebase to v...

Read more...

Changed in linux (Ubuntu):
status: Fix Committed → Fix Released
Brad Figg (brad-figg) wrote :

This bug is awaiting verification that the kernel in -proposed solves the problem. Please test the kernel and update this bug with the results. If the problem is solved, change the tag 'verification-needed-saucy' to 'verification-done-saucy'.

If verification is not done by 5 working days from today, this fix will be dropped from the source code, and this bug will be closed.

See https://wiki.ubuntu.com/Testing/EnableProposed for documentation how to enable and use -proposed. Thank you!

tags: added: verification-needed-saucy
Brad Figg (brad-figg) on 2013-11-21
tags: added: verification-done-saucy
removed: verification-needed-saucy
To post a comment you must log in.
This report contains Public information  Edit
Everyone can see this information.

Other bug subscribers