[   29.257816] init: squid3 main process ended, respawning
[   29.405282] init: squid3 main process (1435) terminated with status 127
[   29.405316] init: squid3 main process ended, respawning
[   29.432741] init: squid3 main process (1441) terminated with status 127
[   29.432777] init: squid3 main process ended, respawning
[   29.458614] init: squid3 main process (1447) terminated with status 127
[   29.458650] init: squid3 main process ended, respawning
[   29.486900] init: squid3 main process (1453) terminated with status 127
[   29.486935] init: squid3 main process ended, respawning
[   29.525515] init: squid3 main process (1459) terminated with status 127
[   29.525552] init: squid3 main process ended, respawning
[   29.551981] init: squid3 main process (1465) terminated with status 127
[   29.552255] init: squid3 main process ended, respawning
[   29.577871] init: squid3 main process (1471) terminated with status 127
[   29.577908] init: squid3 main process ended, respawning
[   29.611077] init: squid3 main process (1477) terminated with status 127
[   29.611112] init: squid3 main process ended, respawning
[   29.649263] init: squid3 main process (1489) terminated with status 127
[   29.649377] init: squid3 main process ended, respawning
[   29.682628] init: squid3 main process (1496) terminated with status 127
[   29.682665] init: squid3 respawning too fast, stopped
[   30.459641] tg3 0000:02:00.0: eth0: Link is up at 1000 Mbps, full duplex
[   30.459656] tg3 0000:02:00.0: eth0: Flow control is on for TX and on for RX
[   30.460252] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   33.502302] NMI watchdog disabled (cpu0): not supported (no LAPIC?)
[   33.502307] watchdog: failed to be enabled on some cpus
[   33.510811] tg3 0000:02:00.0: eth0: Link is down
[   33.605288] uhci_hcd 0000:00:1d.0: PCI INT A disabled
[   33.605445] uhci_hcd 0000:00:1d.1: PCI INT B disabled
[   33.605586] uhci_hcd 0000:00:1d.2: PCI INT C disabled
[   33.747823] uhci_hcd 0000:00:1d.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
[   33.747835] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[   33.787278] uhci_hcd 0000:00:1d.1: PCI INT B -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
[   33.787298] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[   33.831122] uhci_hcd 0000:00:1d.2: PCI INT C -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
[   33.831142] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[   36.693901] tg3 0000:02:00.0: eth0: Link is up at 1000 Mbps, full duplex
[   36.693918] tg3 0000:02:00.0: eth0: Flow control is on for TX and on for RX
[   41.424042] eth0: no IPv6 routers present
[  140.292032] tg3 0000:02:00.0: vpd r/w failed.  This is likely a firmware bug on this device.  Contact the card vendor for a firmware update.
[  141.548031] tg3 0000:02:00.0: vpd r/w failed.  This is likely a firmware bug on this device.  Contact the card vendor for a firmware update.
[  216.038684] audit_printk_skb: 30 callbacks suppressed
[  216.038692] type=1400 audit(1372873626.250:30): apparmor="STATUS" operation="profile_replace" name="system_tor" pid=4754 comm="apparmor_parser"
[  553.614618] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[  553.631733] SGI XFS Quota Management subsystem
[  553.673651] JFS: nTxBlock = 8192, nTxLock = 65536
[  553.754350] NTFS driver 2.1.30 [Flags: R/O MODULE].
[  553.824714] QNX4 filesystem 0.2.3 registered.
[  553.950630] Btrfs loaded
[  721.728030] tg3 0000:02:00.0: vpd r/w failed.  This is likely a firmware bug on this device.  Contact the card vendor for a firmware update.
[  722.584030] tg3 0000:02:00.0: vpd r/w failed.  This is likely a firmware bug on this device.  Contact the card vendor for a firmware update.