Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:32:12 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 39 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 7146.756467] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 3 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7146.756492] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7146.756515] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR2] (Node ffff88021085db90), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7146.756529] ACPI Error: Method parse/execution failed [\ECRW] (Node ffff88021085dcf8), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7146.756542] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7146.756557] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 7147.255330] ACPI: EC: input buffer is not empty, aborting transaction Message repeated 1 times. ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7147.255378] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7147.255390] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7148.225244] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7148.225267] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. Completed 1 S3 cycle(s) Found 11 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 11 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 11 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 11 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 11 s3: HIGH Kernel message: [ 7146.756467] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 7146.756492] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7146.756515] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR2] (Node ffff88021085db90), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7146.756529] ACPI Error: Method parse/execution failed [\ECRW] (Node ffff88021085dcf8), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7146.756542] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7146.756557] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7147.255330] ACPI: EC: input buffer is not empty, aborting transaction s3: HIGH Kernel message: [ 7147.255378] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7147.255390] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7148.225244] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7148.225267] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 11| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 11| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:33:25 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 39 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 7192.992818] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 3 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7192.992843] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7192.992866] ACPI Error: Method parse/execution failed [\ECRB] (Node ffff88021085dcd0), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7192.992881] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7192.992895] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 7193.491677] ACPI: EC: input buffer is not empty, aborting transaction Message repeated 1 times. ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7193.491793] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7193.491806] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7194.465571] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7194.465595] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. Completed 1 S3 cycle(s) Found 10 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 10 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 10 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 10 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 10 s3: HIGH Kernel message: [ 7192.992818] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 7192.992843] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7192.992866] ACPI Error: Method parse/execution failed [\ECRB] (Node ffff88021085dcd0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7192.992881] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7192.992895] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7193.491677] ACPI: EC: input buffer is not empty, aborting transaction s3: HIGH Kernel message: [ 7193.491793] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7193.491806] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7194.465571] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7194.465595] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 10| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 10| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:34:37 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 39 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 7238.658643] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 3 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7238.658673] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7238.658703] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7238.658724] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7238.658742] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7238.658763] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 7239.177637] ACPI: EC: input buffer is not empty, aborting transaction Message repeated 1 times. ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. Completed 1 S3 cycle(s) Found 7 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 7 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 7 s3: HIGH Kernel message: [ 7238.658643] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 7238.658673] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7238.658703] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7238.658724] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7238.658742] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7238.658763] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7239.177637] ACPI: EC: input buffer is not empty, aborting transaction Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 7| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 7| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:35:49 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 40 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 7284.353569] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 3 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7284.353598] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7284.353629] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7284.353651] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7284.353671] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7284.353692] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 7284.875959] ACPI: EC: input buffer is not empty, aborting transaction Message repeated 1 times. ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. Completed 1 S3 cycle(s) Found 7 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 7 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 7 s3: HIGH Kernel message: [ 7284.353569] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 7284.353598] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7284.353629] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7284.353651] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7284.353671] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7284.353692] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7284.875959] ACPI: EC: input buffer is not empty, aborting transaction Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 7| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 7| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:37:01 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 39 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 7329.941793] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 3 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7329.941818] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7329.941841] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR2] (Node ffff88021085db90), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7329.941855] ACPI Error: Method parse/execution failed [\ECRW] (Node ffff88021085dcf8), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7329.941868] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7329.941884] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 7330.440640] ACPI: EC: input buffer is not empty, aborting transaction Message repeated 1 times. ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7330.440759] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7330.440773] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7331.410517] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7331.410541] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. Completed 1 S3 cycle(s) Found 11 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 11 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 11 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 11 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 11 s3: HIGH Kernel message: [ 7329.941793] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 7329.941818] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7329.941841] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR2] (Node ffff88021085db90), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7329.941855] ACPI Error: Method parse/execution failed [\ECRW] (Node ffff88021085dcf8), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7329.941868] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7329.941884] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7330.440640] ACPI: EC: input buffer is not empty, aborting transaction s3: HIGH Kernel message: [ 7330.440759] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7330.440773] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7331.410517] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7331.410541] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 11| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 11| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:38:13 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 38 seconds. Completed 1 S3 cycle(s) PASSED: Test 1, No kernel log errors detected. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. PASSED: Test 1, Found no errors doing 1 suspend/resume cycle(s). ==================================================================================================== 5 passed, 0 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 5 passed, 0 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: NONE Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 5| | | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 5| 0| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:39:24 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 40 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 7421.197236] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 2 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7421.197263] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7421.197292] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR2] (Node ffff88021085db90), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7421.197312] ACPI Error: Method parse/execution failed [\ECRW] (Node ffff88021085dcf8), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7421.197332] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7421.197353] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 7421.696036] ACPI: EC: input buffer is not empty, aborting transaction ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7421.696177] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7421.696194] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7422.446418] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7422.446442] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. Completed 1 S3 cycle(s) Found 11 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 11 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 11 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 11 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 11 s3: HIGH Kernel message: [ 7421.197236] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 7421.197263] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7421.197292] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR2] (Node ffff88021085db90), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7421.197312] ACPI Error: Method parse/execution failed [\ECRW] (Node ffff88021085dcf8), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7421.197332] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7421.197353] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7421.696036] ACPI: EC: input buffer is not empty, aborting transaction s3: HIGH Kernel message: [ 7421.696177] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7421.696194] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7422.446418] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7422.446442] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 11| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 11| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:40:36 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 40 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 7466.495662] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 3 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7466.495688] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7466.495711] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR2] (Node ffff88021085db90), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7466.495725] ACPI Error: Method parse/execution failed [\ECRW] (Node ffff88021085dcf8), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7466.495738] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7466.495753] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 7466.994525] ACPI: EC: input buffer is not empty, aborting transaction Message repeated 1 times. ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7466.994644] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7466.994657] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7467.964377] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7467.964402] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. Completed 1 S3 cycle(s) Found 11 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 11 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 11 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 11 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 11 s3: HIGH Kernel message: [ 7466.495662] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 7466.495688] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7466.495711] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR2] (Node ffff88021085db90), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7466.495725] ACPI Error: Method parse/execution failed [\ECRW] (Node ffff88021085dcf8), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7466.495738] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7466.495753] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7466.994525] ACPI: EC: input buffer is not empty, aborting transaction s3: HIGH Kernel message: [ 7466.994644] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7466.994657] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7467.964377] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7467.964402] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 11| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 11| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:41:49 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 41 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 7512.281060] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 3 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7512.281095] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7512.281122] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7512.281139] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7512.281156] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 7512.799927] ACPI: EC: input buffer is not empty, aborting transaction Message repeated 1 times. ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7512.804050] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7512.804078] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7512.804108] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. Completed 1 S3 cycle(s) Found 9 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 9 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 9 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 9 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 9 s3: HIGH Kernel message: [ 7512.281060] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 7512.281095] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7512.281122] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7512.281139] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7512.281156] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7512.799927] ACPI: EC: input buffer is not empty, aborting transaction s3: HIGH Kernel message: [ 7512.804050] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7512.804078] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7512.804108] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 9| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 9| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:43:02 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 38 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 7557.807005] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 3 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7557.807033] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7557.807056] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR2] (Node ffff88021085db90), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7557.807071] ACPI Error: Method parse/execution failed [\ECRW] (Node ffff88021085dcf8), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7557.807085] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7557.807101] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 7558.305805] ACPI: EC: input buffer is not empty, aborting transaction Message repeated 1 times. ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7558.308920] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7558.308933] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7559.056202] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7559.056226] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. Completed 1 S3 cycle(s) Found 11 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 11 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 11 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 11 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 11 s3: HIGH Kernel message: [ 7557.807005] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 7557.807033] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7557.807056] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR2] (Node ffff88021085db90), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7557.807071] ACPI Error: Method parse/execution failed [\ECRW] (Node ffff88021085dcf8), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7557.807085] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7557.807101] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7558.305805] ACPI: EC: input buffer is not empty, aborting transaction s3: HIGH Kernel message: [ 7558.308920] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7558.308933] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7559.056202] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7559.056226] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 11| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 11| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:44:13 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 40 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 7603.876594] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 2 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7603.876622] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7603.876651] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7603.876672] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7603.876691] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7603.876712] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 7605.072960] ACPI: EC: input buffer is not empty, aborting transaction ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. Completed 1 S3 cycle(s) Found 7 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 7 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 7 s3: HIGH Kernel message: [ 7603.876594] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 7603.876622] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7603.876651] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7603.876672] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7603.876691] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7603.876712] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7605.072960] ACPI: EC: input buffer is not empty, aborting transaction Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 7| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 7| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:45:26 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 39 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 7649.428425] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 2 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7649.428451] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7649.428480] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7649.428501] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7649.428520] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7649.428551] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 7650.594959] ACPI: EC: input buffer is not empty, aborting transaction ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. Completed 1 S3 cycle(s) Found 7 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 7 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 7 s3: HIGH Kernel message: [ 7649.428425] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 7649.428451] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7649.428480] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7649.428501] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7649.428520] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7649.428551] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7650.594959] ACPI: EC: input buffer is not empty, aborting transaction Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 7| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 7| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:46:37 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 39 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 7694.245094] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 3 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7694.245119] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7694.245142] ACPI Error: Method parse/execution failed [\ECRB] (Node ffff88021085dcd0), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7694.245156] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7694.245170] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 7694.747915] ACPI: EC: input buffer is not empty, aborting transaction Message repeated 1 times. ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7694.752132] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7694.752161] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7695.713857] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7695.713881] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. Completed 1 S3 cycle(s) Found 10 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 10 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 10 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 10 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 10 s3: HIGH Kernel message: [ 7694.245094] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 7694.245119] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7694.245142] ACPI Error: Method parse/execution failed [\ECRB] (Node ffff88021085dcd0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7694.245156] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7694.245170] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7694.747915] ACPI: EC: input buffer is not empty, aborting transaction s3: HIGH Kernel message: [ 7694.752132] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7694.752161] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7695.713857] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7695.713881] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 10| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 10| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:47:49 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 40 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 7739.850833] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 3 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7739.850866] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7739.850895] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7739.850914] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7739.850934] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 7740.349717] ACPI: EC: input buffer is not empty, aborting transaction Message repeated 1 times. ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7740.352896] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7740.352917] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7740.352930] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. Completed 1 S3 cycle(s) Found 9 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 9 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 9 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 9 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 9 s3: HIGH Kernel message: [ 7739.850833] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 7739.850866] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7739.850895] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7739.850914] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7739.850934] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7740.349717] ACPI: EC: input buffer is not empty, aborting transaction s3: HIGH Kernel message: [ 7740.352896] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7740.352917] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7740.352930] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 9| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 9| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:49:01 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 41 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 7786.861485] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 1 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7786.861513] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7786.861537] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7786.861551] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7786.861563] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7786.861576] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 7787.778789] ACPI: EC: input buffer is not empty, aborting transaction ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. Completed 1 S3 cycle(s) Found 7 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 7 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 7 s3: HIGH Kernel message: [ 7786.861485] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 7786.861513] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7786.861537] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7786.861551] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7786.861563] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7786.861576] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7787.778789] ACPI: EC: input buffer is not empty, aborting transaction Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 7| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 7| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:50:14 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 38 seconds. Completed 1 S3 cycle(s) PASSED: Test 1, No kernel log errors detected. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. PASSED: Test 1, Found no errors doing 1 suspend/resume cycle(s). ==================================================================================================== 5 passed, 0 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 5 passed, 0 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: NONE Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 5| | | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 5| 0| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:51:24 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 41 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 7875.885900] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 3 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7875.885924] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7875.885947] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR2] (Node ffff88021085db90), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7875.885961] ACPI Error: Method parse/execution failed [\ECRW] (Node ffff88021085dcf8), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7875.885974] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7875.885989] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 7876.384761] ACPI: EC: input buffer is not empty, aborting transaction Message repeated 1 times. ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7876.387982] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7876.388003] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7877.374609] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7877.374633] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. Completed 1 S3 cycle(s) Found 11 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 11 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 11 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 11 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 11 s3: HIGH Kernel message: [ 7875.885900] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 7875.885924] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7875.885947] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR2] (Node ffff88021085db90), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7875.885961] ACPI Error: Method parse/execution failed [\ECRW] (Node ffff88021085dcf8), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7875.885974] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7875.885989] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7876.384761] ACPI: EC: input buffer is not empty, aborting transaction s3: HIGH Kernel message: [ 7876.387982] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7876.388003] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7877.374609] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7877.374633] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 11| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 11| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:52:37 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 38 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 7921.547509] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 3 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7921.547541] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7921.547570] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7921.547590] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7921.547610] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 7922.046390] ACPI: EC: input buffer is not empty, aborting transaction Message repeated 1 times. ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7922.049538] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7922.049557] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7922.049571] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. Completed 1 S3 cycle(s) Found 9 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 9 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 9 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 9 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 9 s3: HIGH Kernel message: [ 7921.547509] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 7921.547541] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7921.547570] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7921.547590] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7921.547610] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7922.046390] ACPI: EC: input buffer is not empty, aborting transaction s3: HIGH Kernel message: [ 7922.049538] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7922.049557] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7922.049571] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 9| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 9| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:53:48 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 40 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 7967.356933] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 3 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7967.356967] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7967.356998] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7967.357020] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7967.357041] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 7967.887669] ACPI: EC: input buffer is not empty, aborting transaction Message repeated 1 times. ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7967.890884] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7967.890906] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 7967.890920] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. Completed 1 S3 cycle(s) Found 9 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 9 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 9 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 9 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 9 s3: HIGH Kernel message: [ 7967.356933] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 7967.356967] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7967.356998] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7967.357020] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7967.357041] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7967.887669] ACPI: EC: input buffer is not empty, aborting transaction s3: HIGH Kernel message: [ 7967.890884] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7967.890906] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 7967.890920] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 9| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 9| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:55:00 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 39 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 8014.211747] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 1 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8014.211772] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8014.211794] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8014.211808] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8014.211820] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8014.211833] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 8014.710595] ACPI: EC: input buffer is not empty, aborting transaction ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. Completed 1 S3 cycle(s) Found 7 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 7 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 7 s3: HIGH Kernel message: [ 8014.211747] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 8014.211772] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8014.211794] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8014.211808] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8014.211820] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8014.211833] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8014.710595] ACPI: EC: input buffer is not empty, aborting transaction Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 7| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 7| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:56:12 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 40 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 8058.368775] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 3 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8058.368808] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8058.368838] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR2] (Node ffff88021085db90), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8058.368858] ACPI Error: Method parse/execution failed [\ECRW] (Node ffff88021085dcf8), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8058.368877] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8058.368900] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 8058.891617] ACPI: EC: input buffer is not empty, aborting transaction Message repeated 1 times. ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8058.895948] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8058.895973] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8059.614066] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8059.614090] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. Completed 1 S3 cycle(s) Found 11 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 11 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 11 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 11 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 11 s3: HIGH Kernel message: [ 8058.368775] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 8058.368808] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8058.368838] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR2] (Node ffff88021085db90), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8058.368858] ACPI Error: Method parse/execution failed [\ECRW] (Node ffff88021085dcf8), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8058.368877] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8058.368900] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8058.891617] ACPI: EC: input buffer is not empty, aborting transaction s3: HIGH Kernel message: [ 8058.895948] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8058.895973] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8059.614066] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8059.614090] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 11| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 11| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:57:24 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 39 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 8104.062731] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 3 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8104.062761] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8104.062791] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8104.062813] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8104.062832] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8104.062852] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 8104.585201] ACPI: EC: input buffer is not empty, aborting transaction Message repeated 1 times. ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. Completed 1 S3 cycle(s) Found 7 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 7 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 7 s3: HIGH Kernel message: [ 8104.062731] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 8104.062761] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8104.062791] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8104.062813] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8104.062832] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8104.062852] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8104.585201] ACPI: EC: input buffer is not empty, aborting transaction Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 7| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 7| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:58:36 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 40 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 8149.684114] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 3 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8149.684148] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8149.684178] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8149.684198] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8149.684218] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 8150.202945] ACPI: EC: input buffer is not empty, aborting transaction Message repeated 1 times. ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8150.206197] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8150.206218] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8150.206231] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. Completed 1 S3 cycle(s) Found 9 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 9 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 9 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 9 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 9 s3: HIGH Kernel message: [ 8149.684114] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 8149.684148] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8149.684178] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8149.684198] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8149.684218] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8150.202945] ACPI: EC: input buffer is not empty, aborting transaction s3: HIGH Kernel message: [ 8150.206197] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8150.206218] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8150.206231] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 9| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 9| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 06:59:48 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 40 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 8196.654729] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 1 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8196.654762] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8196.654794] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8196.654817] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8196.654838] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8196.654859] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 8197.157575] ACPI: EC: input buffer is not empty, aborting transaction ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. Completed 1 S3 cycle(s) Found 7 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 7 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 7 s3: HIGH Kernel message: [ 8196.654729] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 8196.654762] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8196.654794] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8196.654817] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8196.654838] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8196.654859] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8197.157575] ACPI: EC: input buffer is not empty, aborting transaction Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 7| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 7| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 07:01:00 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 39 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 8241.538193] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 2 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8241.538222] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8241.538253] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8241.538273] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8241.538290] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8241.538311] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 8242.739392] ACPI: EC: input buffer is not empty, aborting transaction ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. Completed 1 S3 cycle(s) Found 7 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 7 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 7 s3: HIGH Kernel message: [ 8241.538193] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 8241.538222] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8241.538253] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8241.538273] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8241.538290] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8241.538311] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8242.739392] ACPI: EC: input buffer is not empty, aborting transaction Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 7| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 7| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 07:02:12 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 40 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 8286.645812] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 3 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8286.645842] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8286.645874] ACPI Error: Method parse/execution failed [\ECRB] (Node ffff88021085dcd0), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8286.645897] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8286.645920] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 8287.160631] ACPI: EC: input buffer is not empty, aborting transaction Message repeated 1 times. ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8287.163812] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8287.163825] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8287.895059] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8287.895082] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. Completed 1 S3 cycle(s) Found 10 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 10 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 10 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 10 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 10 s3: HIGH Kernel message: [ 8286.645812] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 8286.645842] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8286.645874] ACPI Error: Method parse/execution failed [\ECRB] (Node ffff88021085dcd0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8286.645897] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8286.645920] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8287.160631] ACPI: EC: input buffer is not empty, aborting transaction s3: HIGH Kernel message: [ 8287.163812] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8287.163825] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8287.895059] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8287.895082] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 10| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 10| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 07:03:25 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 39 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 8332.852568] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 2 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8332.852595] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8332.852625] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8332.852645] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8332.852664] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8332.852684] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 8334.043533] ACPI: EC: input buffer is not empty, aborting transaction ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. Completed 1 S3 cycle(s) Found 7 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 7 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 7 s3: HIGH Kernel message: [ 8332.852568] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 8332.852595] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8332.852625] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8332.852645] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8332.852664] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8332.852684] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8334.043533] ACPI: EC: input buffer is not empty, aborting transaction Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 7| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 7| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 07:04:36 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 40 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 8377.781482] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 3 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8377.781508] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8377.781531] ACPI Error: Method parse/execution failed [\ECRB] (Node ffff88021085dcd0), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8377.781545] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8377.781559] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 3 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 8378.280312] ACPI: EC: input buffer is not empty, aborting transaction Message repeated 1 times. ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8378.284652] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8378.284671] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 1 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8379.246251] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8379.246274] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. Completed 1 S3 cycle(s) Found 10 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 10 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 10 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 10 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 10 s3: HIGH Kernel message: [ 8377.781482] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 8377.781508] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8377.781531] ACPI Error: Method parse/execution failed [\ECRB] (Node ffff88021085dcd0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8377.781545] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8377.781559] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8378.280312] ACPI: EC: input buffer is not empty, aborting transaction s3: HIGH Kernel message: [ 8378.284652] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8378.284671] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8379.246251] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECW1] (Node ffff88021085dbb8), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8379.246274] ACPI Error: Method parse/execution failed [\ECWB] (Node ffff88021085dd20), AE_TIME (20110623/psparse-536) Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 10| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 10| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 07:05:48 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 39 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 8424.177176] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 2 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8424.177205] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8424.177235] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8424.177255] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8424.177272] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8424.177294] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 8425.366792] ACPI: EC: input buffer is not empty, aborting transaction ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. Completed 1 S3 cycle(s) Found 7 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 7 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 7 s3: HIGH Kernel message: [ 8424.177176] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 8424.177205] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8424.177235] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8424.177255] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8424.177272] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8424.177294] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8425.366792] ACPI: EC: input buffer is not empty, aborting transaction Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 7| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 7| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Results generated by fwts: Version V0.25.06precise1 (Tue Sep 4 12:56:28 CST 2012). Some of this work - Copyright (c) 1999 - 2010, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2012, Canonical. This test run on 02/01/13 at 07:07:00 on host Linux 201202-10547 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64. Running tests: s3. S3 suspend/resume test. ---------------------------------------------------------------------------------------------------- Test 1 of 1: S3 suspend/resume test. Defaulted to 1 test, use --s3-multiple=N to run more S3 cycles S3 cycle 1 of 1 pm-suspend returned 0 after 39 seconds. FAILED [HIGH] KlogACPIExceptionAETIMEReturnedByHandler: Test 1, HIGH Kernel message: [ 8469.667461] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) Message repeated 2 times. ADVICE: This is most probably caused by when a read or write operation to the EC memory has failed because of a timeout waiting for the Embedded Controller to complete the transaction. Normally, the kernel waits for 500ms for the Embedded Controller status port to indicate that a transaction is complete, but in this case it has not and a AE_TIME error has been returned. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8469.667485] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8469.667508] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8469.667521] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8469.667533] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 8469.667546] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623 /psparse-536) Message repeated 2 times. ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. FAILED [HIGH] KlogACPIECinputBufferIsNot: Test 1, HIGH Kernel message: [ 8470.872811] ACPI: EC: input buffer is not empty, aborting transaction ADVICE: The ACPI Embedded Controller (EC) driver attempted to perform a read or write transaction but had to abort because the EC was still busy and the input buffer was not emptied within 500ms. Normally this indicates an EC firmware fault. One can try increasing the delay using the acpi.ec_delay kernel parameter or writing to /sys/module/acpi/parameters/ec_delay - however this generally does not help much of the EC firmware is buggy. Completed 1 S3 cycle(s) Found 7 errors in kernel log. PASSED: Test 1, No PM related suspend issues detected. PASSED: Test 1, No device errors detected. PASSED: Test 1, No kernel oopses detected. Found 7 errors and 0 oopses doing 1 suspend/resume cycle(s). ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== 3 passed, 7 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ==================================================================================================== Critical failures: NONE High failures: 7 s3: HIGH Kernel message: [ 8469.667461] ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20110623/evregion-478) s3: HIGH Kernel message: [ 8469.667485] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.ECDV.ECR1] (Node ffff88021085db68), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8469.667508] ACPI Error: Method parse/execution failed [\ECBT] (Node ffff88021085dc80), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8469.667521] ACPI Error: Method parse/execution failed [\ECG2] (Node ffff88021085dd98), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8469.667533] ACPI Error: Method parse/execution failed [\ECG6] (Node ffff88021085deb0), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8469.667546] ACPI Error: Method parse/execution failed [\_SB_.BAT0._BST] (Node ffff88021085e690), AE_TIME (20110623/psparse-536) s3: HIGH Kernel message: [ 8470.872811] ACPI: EC: input buffer is not empty, aborting transaction Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ s3 | 3| 7| | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 7| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+