[ 0.000000] Linux version 2.6.24-3-generic (buildd@vernadsky) (gcc version 4.2.3 20071223 (prerelease) (Ubuntu 4.2.2-4ubuntu3)) #1 SMP Thu Jan 3 23:30:29 UTC 2008 (Ubuntu 2.6.24-3.5-generic) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable) [ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003fef0000 (usable) [ 0.000000] BIOS-e820: 000000003fef0000 - 000000003fef3000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000003fef3000 - 000000003ff00000 (ACPI data) [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) [ 0.000000] 126MB HIGHMEM available. [ 0.000000] 896MB LOWMEM available. [ 0.000000] found SMP MP-table at 000f3ff0 [ 0.000000] Entering add_active_range(0, 0, 261872) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] HighMem 229376 -> 261872 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 261872 [ 0.000000] On node 0 totalpages: 261872 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1760 pages used for memmap [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 [ 0.000000] HighMem zone: 253 pages used for memmap [ 0.000000] HighMem zone: 32243 pages, LIFO batch:7 [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] DMI 2.4 present. [ 0.000000] ACPI: RSDP signature @ 0xC00F7F10 checksum 0 [ 0.000000] ACPI: RSDP 000F7F10, 0014 (r0 RS480 ) [ 0.000000] ACPI: RSDT 3FEF3040, 0030 (r1 RS480 AWRDACPI 42302E31 AWRD 0) [ 0.000000] ACPI: FACP 3FEF30C0, 0084 (r2 RS480 AWRDACPI 42302E31 AWRD 0) [ 0.000000] ACPI: DSDT 3FEF31C0, 3A20 (r1 RS480 AWRDACPI 1000 MSFT 100000E) [ 0.000000] ACPI: FACS 3FEF0000, 0040 [ 0.000000] ACPI: MCFG 3FEF6D00, 003C (r1 RS480 AWRDACPI 42302E31 AWRD 0) [ 0.000000] ACPI: APIC 3FEF6C40, 0068 (r1 RS480 AWRDACPI 42302E31 AWRD 0) [ 0.000000] ATI board detected. Disabling timer routing over 8254. [ 0.000000] ACPI: PM-Timer IO Port: 0x4008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] Processor #0 15:15 APIC version 16 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at 40000000 (gap: 3ff00000:a0100000) [ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259827 [ 0.000000] Kernel command line: BOOT_IMAGE=/casper/vmlinuz file=/cdrom/preseed/kubuntu.seed boot=casper initrd=/casper/initrd.gz quiet splash -- [ 0.000000] mapped APIC to ffffb000 (fee00000) [ 0.000000] mapped IOAPIC to ffffa000 (fec00000) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Detected 2188.885 MHz processor. [ 46.699485] Console: colour VGA+ 80x25 [ 46.699488] console [tty0] enabled [ 46.699766] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 46.700084] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 46.718240] Memory: 1026040k/1047488k available (2127k kernel code, 20844k reserved, 988k data, 364k init, 129984k highmem) [ 46.718247] virtual kernel memory layout: [ 46.718248] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB) [ 46.718249] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 46.718250] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) [ 46.718251] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 46.718252] .init : 0xc0411000 - 0xc046c000 ( 364 kB) [ 46.718253] .data : 0xc0313c7d - 0xc040ad64 ( 988 kB) [ 46.718254] .text : 0xc0100000 - 0xc0313c7d (2127 kB) [ 46.718257] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 46.718287] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1 [ 46.798172] Calibrating delay using timer specific routine.. 4382.06 BogoMIPS (lpj=8764138) [ 46.798194] Security Framework initialized [ 46.798199] SELinux: Disabled at boot. [ 46.798202] Capability LSM initialized [ 46.798213] Mount-cache hash table entries: 512 [ 46.798307] CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001 00000000 [ 46.798314] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 46.798316] CPU: L2 Cache: 512K (64 bytes/line) [ 46.798319] CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000001 00000000 00000001 00000000 [ 46.798326] Compat vDSO mapped to ffffe000. [ 46.798335] Checking 'hlt' instruction... OK. [ 46.814357] SMP alternatives: switching to UP code [ 46.815235] Freeing SMP alternatives: 11k freed [ 46.815325] Early unpacking initramfs... done [ 47.106827] ACPI: Core revision 20070126 [ 47.106869] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found. [ 47.113952] CPU0: AMD Athlon(tm) 64 Processor 3500+ stepping 02 [ 47.113971] Total of 1 processors activated (4382.06 BogoMIPS). [ 47.114131] ENABLING IO-APIC IRQs [ 47.114307] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 47.153965] ..MP-BIOS bug: 8254 timer not connected to IO-APIC [ 47.154019] ...trying to set up timer (IRQ0) through the 8259A ... failed. [ 47.154021] ...trying to set up timer as Virtual Wire IRQ... works. [ 47.301339] Brought up 1 CPUs [ 47.301356] CPU0 attaching sched-domain: [ 47.301358] domain 0: span 01 [ 47.301360] groups: 01 [ 47.301489] net_namespace: 64 bytes [ 47.301493] Booting paravirtualized kernel on bare hardware [ 47.301876] Time: 23:02:08 Date: 01/27/08 [ 47.301911] NET: Registered protocol family 16 [ 47.302036] EISA bus registered [ 47.302060] ACPI: bus type pci registered [ 47.334318] PCI: PCI BIOS revision 3.00 entry at 0xfa290, last bus=2 [ 47.334320] PCI: Using configuration type 1 [ 47.334321] Setting up standard PCI resources [ 47.337506] ACPI: EC: Look up EC in DSDT [ 47.339868] ACPI: Interpreter enabled [ 47.339870] ACPI: (supports S0 S3 S4 S5) [ 47.339880] ACPI: Using IOAPIC for interrupt routing [ 47.342798] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 47.344075] PCI: Transparent bridge - 0000:00:14.4 [ 47.344103] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 47.344218] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT] [ 47.356264] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 47.356337] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 47.356408] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 47.356478] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 47.356549] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11) [ 47.356619] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 *11) [ 47.356689] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 *11) [ 47.356759] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 *10 11) [ 47.356838] Linux Plug and Play Support v0.97 (c) Adam Belay [ 47.356859] pnp: PnP ACPI init [ 47.356864] ACPI: bus type pnp registered [ 47.358613] pnpacpi: exceeded the max number of mem resources: 12 [ 47.358703] pnp: PnP ACPI: found 13 devices [ 47.358705] ACPI: ACPI bus type pnp unregistered [ 47.358707] PnPBIOS: Disabled by ACPI PNP [ 47.358837] PCI: Using ACPI for IRQ routing [ 47.358839] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 47.358845] PCI: Cannot allocate resource region 3 of device 0000:00:00.0 [ 47.413139] NET: Registered protocol family 8 [ 47.413140] NET: Registered protocol family 20 [ 47.417108] Time: tsc clocksource has been installed. [ 47.425116] system 00:01: ioport range 0x228-0x22f has been reserved [ 47.425119] system 00:01: ioport range 0x40b-0x40b has been reserved [ 47.425121] system 00:01: ioport range 0x4d6-0x4d6 has been reserved [ 47.425123] system 00:01: ioport range 0xc00-0xc01 has been reserved [ 47.425125] system 00:01: ioport range 0xc14-0xc14 has been reserved [ 47.425127] system 00:01: ioport range 0xc50-0xc52 has been reserved [ 47.425129] system 00:01: ioport range 0xc6c-0xc6d has been reserved [ 47.425131] system 00:01: ioport range 0xc6f-0xc6f has been reserved [ 47.425133] system 00:01: ioport range 0xcd4-0xcdf has been reserved [ 47.425136] system 00:01: ioport range 0x4000-0x40fe has been reserved [ 47.425138] system 00:01: ioport range 0x4210-0x4217 has been reserved [ 47.425143] system 00:06: ioport range 0x4d0-0x4d1 has been reserved [ 47.425146] system 00:06: ioport range 0x800-0x87f has been reserved [ 47.425151] system 00:0b: iomem range 0xe0000000-0xefffffff could not be reserved [ 47.425155] system 00:0c: iomem range 0xd0000-0xd3fff has been reserved [ 47.425158] system 00:0c: iomem range 0xd5000-0xd7fff has been reserved [ 47.425160] system 00:0c: iomem range 0xf0000-0xfbfff could not be reserved [ 47.425162] system 00:0c: iomem range 0xfc000-0xfffff could not be reserved [ 47.425164] system 00:0c: iomem range 0x3ff00000-0x3fffffff has been reserved [ 47.425167] system 00:0c: iomem range 0x3fef0000-0x3fefffff could not be reserved [ 47.425169] system 00:0c: iomem range 0xffff0000-0xffffffff could not be reserved [ 47.425172] system 00:0c: iomem range 0x0-0x9ffff could not be reserved [ 47.425174] system 00:0c: iomem range 0x100000-0x3feeffff could not be reserved [ 47.425176] system 00:0c: iomem range 0x0-0x0 could not be reserved [ 47.425178] system 00:0c: iomem range 0xfec00000-0xfec00fff could not be reserved [ 47.425181] system 00:0c: iomem range 0xfee00000-0xfee00fff could not be reserved [ 47.455424] PCI: Bridge: 0000:00:02.0 [ 47.455426] IO window: e000-efff [ 47.455429] MEM window: fa000000-fcffffff [ 47.455431] PREFETCH window: d0000000-dfffffff [ 47.455434] PCI: Bridge: 0000:00:14.4 [ 47.455437] IO window: d000-dfff [ 47.455443] MEM window: fde00000-fdefffff [ 47.455448] PREFETCH window: fdd00000-fddfffff [ 47.455461] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 47.455476] NET: Registered protocol family 2 [ 47.493037] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 47.493266] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 47.493917] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 47.494254] TCP: Hash tables configured (established 131072 bind 65536) [ 47.494256] TCP reno registered [ 47.505065] checking if image is initramfs... it is [ 47.956181] Switched to high resolution mode on CPU 0 [ 48.067635] Freeing initrd memory: 7781k freed [ 48.068053] audit: initializing netlink socket (disabled) [ 48.068063] audit(1201474929.208:1): initialized [ 48.068172] highmem bounce pool size: 64 pages [ 48.069372] VFS: Disk quotas dquot_6.5.1 [ 48.069421] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 48.069523] AppArmor: Unable to register AppArmor [ 48.069590] io scheduler noop registered [ 48.069592] io scheduler anticipatory registered [ 48.069593] io scheduler deadline registered [ 48.069601] io scheduler cfq registered (default) [ 48.069607] PCI: MSI quirk detected. MSI deactivated. [ 48.123848] Boot video device is 0000:01:00.0 [ 48.123914] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 48.123936] assign_interrupt_mode Found MSI capability [ 48.123938] Allocate Port Service[0000:00:02.0:pcie00] [ 48.124082] isapnp: Scanning for PnP cards... [ 48.478040] isapnp: No Plug & Play device found [ 48.497478] Real Time Clock Driver v1.12ac [ 48.497544] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 48.498339] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 48.498389] input: Macintosh mouse button emulation as /devices/virtual/input/input0 [ 48.498454] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 48.501445] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 48.501449] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 48.503333] mice: PS/2 mouse device common for all mice [ 48.503411] EISA: Probing bus 0 at eisa.0 [ 48.503431] Cannot allocate resource for EISA slot 4 [ 48.503449] EISA: Detected 0 cards. [ 48.503452] cpuidle: using governor ladder [ 48.503453] cpuidle: using governor menu [ 48.503516] TCP cubic registered [ 48.503522] NET: Registered protocol family 1 [ 48.503540] Using IPI No-Shortcut mode [ 48.503638] Magic number: 8:400:50 [ 48.503951] Freeing unused kernel memory: 364k freed [ 48.535095] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 [ 49.714664] fuse init (API version 7.9) [ 49.725397] ACPI: Processor [CPU0] (supports 8 throttling states) [ 49.725408] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126] [ 50.228788] SCSI subsystem initialized [ 50.276161] libata version 3.00 loaded. [ 50.293609] usbcore: registered new interface driver usbfs [ 50.293625] usbcore: registered new interface driver hub [ 50.311913] usbcore: registered new device driver usb [ 50.323927] ACPI: PCI Interrupt 0000:00:11.0[A] -> GSI 23 (level, low) -> IRQ 16 [ 50.323973] ACPI: PCI interrupt for device 0000:00:11.0 disabled [ 50.323994] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 17 [ 50.324018] ACPI: PCI interrupt for device 0000:00:12.0 disabled [ 50.324034] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 18 [ 50.324057] ACPI: PCI interrupt for device 0000:00:14.1 disabled [ 50.331749] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 50.334027] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 50.351858] sata_sil 0000:00:11.0: version 2.3 [ 50.351893] ACPI: PCI Interrupt 0000:00:11.0[A] -> GSI 23 (level, low) -> IRQ 16 [ 50.363787] scsi0 : sata_sil [ 50.383748] scsi1 : sata_sil [ 50.383833] ata1: SATA max UDMA/100 mmio m512@0xfe02f000 tf 0xfe02f080 irq 16 [ 50.383837] ata2: SATA max UDMA/100 mmio m512@0xfe02f000 tf 0xfe02f0c0 irq 16 [ 50.395761] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver [ 50.419711] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004) [ 50.503626] Floppy drive(s): fd0 is 1.44M [ 50.523897] FDC 0 is a post-1991 82077 [ 50.695200] ata1: SATA link down (SStatus 0 SControl 300) [ 51.006625] ata2: SATA link down (SStatus 0 SControl 300) [ 51.006692] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 17 [ 51.006763] scsi2 : sata_sil [ 51.006909] scsi3 : sata_sil [ 51.006971] ata3: SATA max UDMA/100 mmio m512@0xfe02e000 tf 0xfe02e080 irq 17 [ 51.006974] ata4: SATA max UDMA/100 mmio m512@0xfe02e000 tf 0xfe02e0c0 irq 17 [ 51.318063] ata3: SATA link down (SStatus 0 SControl 300) [ 51.629496] ata4: SATA link down (SStatus 0 SControl 300) [ 51.629629] ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 19 [ 51.629642] ehci_hcd 0000:00:13.2: EHCI Host Controller [ 51.629851] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1 [ 51.629905] ehci_hcd 0000:00:13.2: irq 19, io mem 0xfe02b000 [ 51.641479] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 51.641594] usb usb1: configuration #1 chosen from 1 choice [ 51.641613] hub 1-0:1.0: USB hub found [ 51.641618] hub 1-0:1.0: 8 ports detected [ 51.745422] ATIIXP: IDE controller (0x1002:0x4376 rev 0x00) at PCI slot 0000:00:14.1 [ 51.745438] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 18 [ 51.745446] ATIIXP: not 100% native mode: will probe irqs later [ 51.745463] ide0: BM-DMA at 0xf300-0xf307, BIOS settings: hda:pio, hdb:pio [ 51.745475] ide1: BM-DMA at 0xf308-0xf30f, BIOS settings: hdc:pio, hdd:pio [ 51.745484] Probing IDE interface ide0... [ 52.029182] hdb: ST3200826A, ATA DISK drive [ 52.308263] hdb: host max PIO4 wanted PIO255(auto-tune) selected PIO4 [ 52.308406] hdb: UDMA/100 mode selected [ 52.308528] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 52.310067] Probing IDE interface ide1... [ 53.099246] hdd: LITE-ON CD-ROM LTN-4891S, ATAPI CD/DVD-ROM drive [ 53.881831] hdc: LITE-ON DVDRW SOHW-1633S, ATAPI CD/DVD-ROM drive [ 53.881841] hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO4 [ 53.882187] hdc: UDMA/66 mode selected [ 53.882466] hdd: host max PIO4 wanted PIO255(auto-tune) selected PIO4 [ 53.882651] hdd: UDMA/33 mode selected [ 53.882874] ide1 at 0x170-0x177,0x376 on irq 15 [ 53.906400] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19 [ 53.906412] ohci_hcd 0000:00:13.0: OHCI Host Controller [ 53.906433] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2 [ 53.906446] ohci_hcd 0000:00:13.0: irq 19, io mem 0xfe02d000 [ 53.965350] usb usb2: configuration #1 chosen from 1 choice [ 53.965366] hub 2-0:1.0: USB hub found [ 53.965374] hub 2-0:1.0: 4 ports detected [ 54.069131] ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19 [ 54.069140] ohci_hcd 0000:00:13.1: OHCI Host Controller [ 54.069154] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3 [ 54.069166] ohci_hcd 0000:00:13.1: irq 19, io mem 0xfe02c000 [ 54.129045] usb usb3: configuration #1 chosen from 1 choice [ 54.129059] hub 3-0:1.0: USB hub found [ 54.129066] hub 3-0:1.0: 4 ports detected [ 54.232908] 8139cp 0000:02:03.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip [ 54.232911] 8139cp 0000:02:03.0: Try the "8139too" driver instead. [ 54.234427] ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 21 (level, low) -> IRQ 21 [ 54.287092] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[21] MMIO=[fdefe000-fdefe7ff] Max Packet=[2048] IR/IT contexts=[4/8] [ 54.293662] 8139too Fast Ethernet driver 0.9.28 [ 54.309368] ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 20 (level, low) -> IRQ 20 [ 54.310113] eth0: RealTek RTL8139 at 0xf8922000, 00:13:d3:a2:cd:18, IRQ 20 [ 54.310115] eth0: Identified 8139 chip type 'RTL-8100B/8139D' [ 54.331796] hdb: max request size: 512KiB [ 54.331937] hdb: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63 [ 54.332112] hdb: cache flushes supported [ 54.332136] hdb: hdb1 hdb2 [ 54.352579] hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache [ 54.352586] Uniform CD-ROM driver Revision: 3.20 [ 54.697082] hdd: ATAPI 48X CD-ROM drive, 96kB Cache [ 54.735905] usb 2-2: new low speed USB device using ohci_hcd and address 2 [ 54.949596] usb 2-2: configuration #1 chosen from 1 choice [ 55.254929] usb 3-4: new full speed USB device using ohci_hcd and address 2 [ 55.463669] usb 3-4: configuration #1 chosen from 1 choice [ 55.465724] usbcore: registered new interface driver hiddev [ 55.471754] input: Microsoft Microsoft Wireless Intellimouse Explorer® 1.0A as /devices/pci0000:00/0000:00:13.0/usb2/2-2/2-2:1.0/input/input2 [ 55.482558] input,hidraw0: USB HID v1.10 Mouse [Microsoft Microsoft Wireless Intellimouse Explorer® 1.0A] on usb-0000:00:13.0-2 [ 55.482574] usbcore: registered new interface driver usbhid [ 55.482577] /build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 55.483473] usbcore: registered new interface driver libusual [ 55.494521] Initializing USB Mass Storage driver... [ 55.497241] scsi4 : SCSI emulation for USB Mass Storage devices [ 55.497817] usbcore: registered new interface driver usb-storage [ 55.497820] USB Mass Storage support registered. [ 55.497894] usb-storage: device found at 2 [ 55.497895] usb-storage: waiting for device to settle before scanning [ 55.574450] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0010dc00009c4011] [ 60.486598] usb-storage: device scan complete [ 60.492584] scsi 4:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0 [ 60.498570] scsi 4:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0 [ 60.504559] scsi 4:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0 [ 60.510547] scsi 4:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0 [ 60.527565] sd 4:0:0:0: [sda] Attached SCSI removable disk [ 60.537518] sd 4:0:0:1: [sdb] Attached SCSI removable disk [ 60.547499] sd 4:0:0:2: [sdc] Attached SCSI removable disk [ 60.557481] sd 4:0:0:3: [sdd] Attached SCSI removable disk [ 60.564297] sd 4:0:0:0: Attached scsi generic sg0 type 0 [ 60.564312] sd 4:0:0:1: Attached scsi generic sg1 type 0 [ 60.564325] sd 4:0:0:2: Attached scsi generic sg2 type 0 [ 60.564340] sd 4:0:0:3: Attached scsi generic sg3 type 0 [ 90.429560] end_request: I/O error, dev fd0, sector 0 [ 128.468553] end_request: I/O error, dev fd0, sector 0 [ 128.468556] Buffer I/O error on device fd0, logical block 0 [ 166.504284] end_request: I/O error, dev fd0, sector 0 [ 166.504286] Buffer I/O error on device fd0, logical block 0 [ 205.549077] end_request: I/O error, dev fd0, sector 0 [ 243.584999] end_request: I/O error, dev fd0, sector 0 [ 243.585002] Buffer I/O error on device fd0, logical block 0 [ 281.623865] end_request: I/O error, dev fd0, sector 0 [ 281.623867] Buffer I/O error on device fd0, logical block 0 [ 284.792137] ISO 9660 Extensions: Microsoft Joliet Level 3 [ 284.818183] ISO 9660 Extensions: RRIP_1991A [ 285.177925] Registering unionfs 1.4 [ 285.177928] unionfs: debugging is not enabled [ 285.187188] loop: module loaded [ 285.574501] squashfs: version 3.3 (2007/10/31) Phillip Lougher [ 339.793444] input: PC Speaker as /devices/platform/pcspkr/input/input3 [ 340.143124] logips2pp: Detected unknown logitech mouse model 90 [ 340.630006] input: ImExPS/2 Logitech Explorer Mouse as /devices/platform/i8042/serio1/input/input4 [ 340.798438] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 341.719748] Linux agpgart interface v0.102 [ 341.854871] parport_pc 00:08: reported by Plug and Play ACPI [ 341.854908] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP] [ 342.109245] input: Power Button (FF) as /devices/virtual/input/input5 [ 342.132048] ACPI: Power Button (FF) [PWRF] [ 342.132093] input: Power Button (CM) as /devices/virtual/input/input6 [ 342.156001] ACPI: Power Button (CM) [PWRB] [ 342.648680] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 342.743265] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device [ 345.112487] ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 22 [ 346.582903] device-mapper: uevent: version 1.0.3 [ 346.582924] device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com [ 348.740830] No dock devices found. [ 349.015365] toshiba_acpi: Unknown parameter `hotkeys_over_acpi' [ 350.593625] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3500+ processors (1 cpu cores) (version 2.20.00) [ 350.605801] powernow-k8: BIOS error - no PSB or ACPI _PSS objects [ 356.539004] avahi-daemon[8060]: segfault at 00000000 eip 0804d82b esp bfff70a0 error 4 [ 378.057513] lp0: using parport0 (interrupt-driven). [ 378.355732] ppdev: user-space parallel port driver [ 394.839463] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 [ 395.604650] Bluetooth: Core ver 2.11 [ 395.604707] NET: Registered protocol family 31 [ 395.604709] Bluetooth: HCI device and connection manager initialized [ 395.604712] Bluetooth: HCI socket layer initialized [ 397.254379] Bluetooth: L2CAP ver 2.9 [ 397.254383] Bluetooth: L2CAP socket layer initialized [ 397.512950] Bluetooth: RFCOMM socket layer initialized [ 397.512962] Bluetooth: RFCOMM TTY layer initialized [ 397.512964] Bluetooth: RFCOMM ver 1.8 [ 399.650755] NET: Registered protocol family 17 [ 401.933018] NET: Registered protocol family 10 [ 401.933178] lo: Disabled Privacy Extensions [ 412.748242] eth0: no IPv6 routers present [ 7900.012229] usb 1-2: new high speed USB device using ehci_hcd and address 6 [ 7900.146802] usb 1-2: configuration #1 chosen from 1 choice [ 7900.154000] scsi5 : SCSI emulation for USB Mass Storage devices [ 7900.155879] usb-storage: device found at 6 [ 7900.155883] usb-storage: waiting for device to settle before scanning [ 7905.143617] usb-storage: device scan complete [ 7905.144738] scsi 5:0:0:0: Direct-Access Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 2 [ 7905.154533] sd 5:0:0:0: [sde] 3987456 512-byte hardware sectors (2042 MB) [ 7905.155229] sd 5:0:0:0: [sde] Write Protect is off [ 7905.155232] sd 5:0:0:0: [sde] Mode Sense: 23 00 00 00 [ 7905.155234] sd 5:0:0:0: [sde] Assuming drive cache: write through [ 7905.158329] sd 5:0:0:0: [sde] 3987456 512-byte hardware sectors (2042 MB) [ 7905.159201] sd 5:0:0:0: [sde] Write Protect is off [ 7905.159205] sd 5:0:0:0: [sde] Mode Sense: 23 00 00 00 [ 7905.159207] sd 5:0:0:0: [sde] Assuming drive cache: write through [ 7905.159211] sde: sde1 [ 7905.247389] sd 5:0:0:0: [sde] Attached SCSI removable disk [ 7905.247427] sd 5:0:0:0: Attached scsi generic sg4 type 0 [11081.269144] usb 1-2: USB disconnect, address 6