[ 0.000000] Linux version 2.6.20-9-generic (root@rothera) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu3)) #2 SMP Mon Feb 26 03:01:44 UTC 2007 (Ubuntu 2.6.20-9.16-generic) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] sanitize start [ 0.000000] sanitize end [ 0.000000] copy_e820_map() start: 0000000000000000 size: 00000000000a0000 end: 00000000000a0000 type: 1 [ 0.000000] copy_e820_map() type is E820_RAM [ 0.000000] copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end: 0000000000100000 type: 2 [ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000005fef0000 end: 000000005fff0000 type: 1 [ 0.000000] copy_e820_map() type is E820_RAM [ 0.000000] copy_e820_map() start: 000000005fff0000 size: 0000000000003000 end: 000000005fff3000 type: 4 [ 0.000000] copy_e820_map() start: 000000005fff3000 size: 000000000000d000 end: 0000000060000000 type: 3 [ 0.000000] copy_e820_map() start: 00000000fec00000 size: 0000000000001000 end: 00000000fec01000 type: 2 [ 0.000000] copy_e820_map() start: 00000000fee00000 size: 0000000000001000 end: 00000000fee01000 type: 2 [ 0.000000] copy_e820_map() start: 00000000ffff0000 size: 0000000000010000 end: 0000000100000000 type: 2 [ 0.000000] BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000005fff0000 (usable) [ 0.000000] BIOS-e820: 000000005fff0000 - 000000005fff3000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000005fff3000 - 0000000060000000 (ACPI data) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) [ 0.000000] 639MB HIGHMEM available. [ 0.000000] 896MB LOWMEM available. [ 0.000000] Entering add_active_range(0, 0, 393200) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] HighMem 229376 -> 393200 [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 393200 [ 0.000000] On node 0 totalpages: 393200 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1760 pages used for memmap [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 [ 0.000000] HighMem zone: 1279 pages used for memmap [ 0.000000] HighMem zone: 162545 pages, LIFO batch:31 [ 0.000000] DMI 2.2 present. [ 0.000000] ACPI: RSDP (v000 Nvidia ) @ 0x000f68e0 [ 0.000000] ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x5fff3000 [ 0.000000] ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x5fff3040 [ 0.000000] ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000 [ 0.000000] Nvidia board detected. Ignoring ACPI timer override. [ 0.000000] If you got timer trouble try acpi_use_timer_override [ 0.000000] Nvidia board detected. Ignoring ACPI timer override. [ 0.000000] If you got timer trouble try acpi_use_timer_override [ 0.000000] ACPI: PM-Timer IO Port: 0x4008 [ 0.000000] Allocating PCI resources starting at 70000000 (gap: 60000000:9ec00000) [ 0.000000] Detected 2191.261 MHz processor. [ 28.406323] Built 1 zonelists. Total pages: 390129 [ 28.406327] Kernel command line: root=UUID=5f29d884-300a-4798-b5ef-b9ab5d2f0e21 ro quiet splash locale=de_DE vga=0x31A [ 28.406482] Found and enabled local APIC! [ 28.406485] mapped APIC to ffffd000 (fee00000) [ 28.406488] Enabling fast FPU save and restore... done. [ 28.406491] Enabling unmasked SIMD FPU exception support... done. [ 28.406499] Initializing CPU#0 [ 28.406557] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 28.406641] Console: colour dummy device 80x25 [ 28.407133] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 28.407558] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 28.452789] Memory: 1548384k/1572800k available (1979k kernel code, 23204k reserved, 882k data, 324k init, 655296k highmem) [ 28.452799] virtual kernel memory layout: [ 28.452800] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB) [ 28.452801] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 28.452802] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) [ 28.452803] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 28.452805] .init : 0xc03d1000 - 0xc0422000 ( 324 kB) [ 28.452806] .data : 0xc02eed54 - 0xc03cb6d4 ( 882 kB) [ 28.452807] .text : 0xc0100000 - 0xc02eed54 (1979 kB) [ 28.452810] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 28.530484] Calibrating delay using timer specific routine.. 4385.92 BogoMIPS (lpj=8771857) [ 28.530527] Security Framework v1.0.0 initialized [ 28.530534] SELinux: Disabled at boot. [ 28.530550] Mount-cache hash table entries: 512 [ 28.530698] CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000 [ 28.530706] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 28.530709] CPU: L2 Cache: 512K (64 bytes/line) [ 28.530712] CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000420 00000000 00000000 00000000 [ 28.530731] Checking 'hlt' instruction... OK. [ 28.546594] SMP alternatives: switching to UP code [ 28.546845] Freeing SMP alternatives: 11k freed [ 28.546953] ACPI: Core revision 20060707 [ 28.555420] ACPI: setting ELCR to 0200 (from 1cb8) [ 28.556319] CPU0: AMD Athlon(tm) XP 3200+ stepping 00 [ 28.556324] SMP motherboard not detected. [ 28.662454] Brought up 1 CPUs [ 28.662687] Booting paravirtualized kernel on bare hardware [ 28.662751] Time: 8:42:24 Date: 02/02/107 [ 28.662783] NET: Registered protocol family 16 [ 28.662881] EISA bus registered [ 28.662885] ACPI: bus type pci registered [ 28.694701] PCI: PCI BIOS revision 2.10 entry at 0xfb540, last bus=2 [ 28.694704] PCI: Using configuration type 1 [ 28.694705] Setting up standard PCI resources [ 28.708378] ACPI: Interpreter enabled [ 28.708380] ACPI: Using PIC for interrupt routing [ 28.708861] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 28.708866] PCI: Probing PCI hardware (bus 00) [ 28.709079] PCI: nForce2 C1 Halt Disconnect fixup [ 28.709807] Boot video device is 0000:02:00.0 [ 28.709851] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 28.752576] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] [ 28.753028] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT] [ 28.753897] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 *10 11 12 14 15) [ 28.754152] ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 *5 6 7 10 11 12 14 15) [ 28.754414] ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 *7 10 11 12 14 15) [ 28.754669] ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 10 11 *12 14 15) [ 28.755059] ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 28.755313] ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 10 *11 12 14 15) [ 28.755566] ACPI: PCI Interrupt Link [LUBB] (IRQs 3 *4 5 6 7 10 11 12 14 15) [ 28.755819] ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 10 *11 12 14 15) [ 28.756073] ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 28.756327] ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 28.756581] ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 28.756841] ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 *10 11 12 14 15) [ 28.757096] ACPI: PCI Interrupt Link [LUB2] (IRQs *3 4 5 6 7 10 11 12 14 15) [ 28.757348] ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 28.757601] ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 28.757855] ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 28.758089] ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled. [ 28.758314] ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled. [ 28.758547] ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled. [ 28.758768] ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled. [ 28.758988] ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled. [ 28.759276] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0, disabled. [ 28.759564] ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0, disabled. [ 28.759860] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0, disabled. [ 28.760149] ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0, disabled. [ 28.760436] ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0, disabled. [ 28.760723] ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled. [ 28.760950] ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled. [ 28.761236] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0, disabled. [ 28.761522] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0, disabled. [ 28.761807] ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled. [ 28.762094] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled. [ 28.763827] Linux Plug and Play Support v0.97 (c) Adam Belay [ 28.763837] pnp: PnP ACPI init [ 28.767438] pnp: PnP ACPI: found 10 devices [ 28.767443] PnPBIOS: Disabled by ACPI PNP [ 28.767493] PCI: Using ACPI for IRQ routing [ 28.767498] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 28.771042] spurious 8259A interrupt: IRQ7. [ 28.806273] pnp: 00:00: ioport range 0x4000-0x407f could not be reserved [ 28.806277] pnp: 00:00: ioport range 0x4080-0x40ff has been reserved [ 28.806279] pnp: 00:00: ioport range 0x4400-0x447f has been reserved [ 28.806282] pnp: 00:00: ioport range 0x4480-0x44ff could not be reserved [ 28.806285] pnp: 00:00: ioport range 0x4200-0x427f has been reserved [ 28.806287] pnp: 00:00: ioport range 0x4280-0x42ff has been reserved [ 28.806291] pnp: 00:01: ioport range 0x5000-0x503f has been reserved [ 28.806294] pnp: 00:01: ioport range 0x5500-0x553f has been reserved [ 28.806520] PCI: Bridge: 0000:00:08.0 [ 28.806523] IO window: d000-dfff [ 28.806527] MEM window: da000000-daffffff [ 28.806531] PREFETCH window: disabled. [ 28.806537] PCI: Bridge: 0000:00:1e.0 [ 28.806538] IO window: disabled. [ 28.806542] MEM window: d8000000-d9ffffff [ 28.806546] PREFETCH window: d0000000-d7ffffff [ 28.806556] PCI: Setting latency timer of device 0000:00:08.0 to 64 [ 28.806586] NET: Registered protocol family 2 [ 28.842377] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 28.842560] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 28.843707] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 28.844319] TCP: Hash tables configured (established 131072 bind 65536) [ 28.844322] TCP reno registered [ 28.854426] checking if image is initramfs... it is [ 29.339793] Freeing initrd memory: 6438k freed [ 29.340203] audit: initializing netlink socket (disabled) [ 29.340216] audit(1172824945.012:1): initialized [ 29.340274] highmem bounce pool size: 64 pages [ 29.340323] VFS: Disk quotas dquot_6.5.1 [ 29.340344] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 29.340390] io scheduler noop registered [ 29.340393] io scheduler anticipatory registered [ 29.340395] io scheduler deadline registered [ 29.340401] io scheduler cfq registered (default) [ 29.394167] isapnp: Scanning for PnP cards... [ 29.748399] isapnp: No Plug & Play device found [ 29.770638] Real Time Clock Driver v1.12ac [ 29.770686] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 29.771209] mice: PS/2 mouse device common for all mice [ 29.771726] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 29.771951] input: Macintosh mouse button emulation as /class/input/input0 [ 29.771981] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 29.771985] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 29.772211] PNP: No PS/2 controller found. Probing ports directly. [ 30.021973] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 30.022096] EISA: Probing bus 0 at eisa.0 [ 30.022117] Cannot allocate resource for EISA slot 4 [ 30.022119] Cannot allocate resource for EISA slot 5 [ 30.022134] EISA: Detected 0 cards. [ 30.052200] TCP cubic registered [ 30.052205] NET: Registered protocol family 1 [ 30.052211] NET: Registered protocol family 8 [ 30.052213] NET: Registered protocol family 20 [ 30.052267] Testing NMI watchdog ... OK. [ 30.091957] Using IPI No-Shortcut mode [ 30.091998] ACPI: (supports S0 S1 S4 S5) [ 30.092042] Magic number: 15:659:724 [ 30.092513] Freeing unused kernel memory: 324k freed [ 30.093509] Time: tsc clocksource has been installed. [ 30.163975] vesafb: framebuffer at 0xd0000000, mapped to 0xf8880000, using 5120k, total 131072k [ 30.163980] vesafb: mode is 1280x1024x16, linelength=2560, pages=1 [ 30.163983] vesafb: protected mode interface info at c000:e0b0 [ 30.163986] vesafb: pmi: set display start = c00ce0e6, set palette = c00ce150 [ 30.163988] vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da [ 30.163997] vesafb: scrolling: redraw [ 30.164000] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 [ 30.217674] Console: switching to colour frame buffer device 160x64 [ 30.271174] fb0: VESA VGA frame buffer device [ 31.510883] Capability LSM initialized [ 31.966284] usbcore: registered new interface driver usbfs [ 31.966307] usbcore: registered new interface driver hub [ 31.966328] usbcore: registered new device driver usb [ 31.966945] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver [ 31.967256] ACPI: PCI Interrupt Link [LUBA] enabled at IRQ 11 [ 31.967260] PCI: setting IRQ 11 as level-triggered [ 31.967264] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUBA] -> GSI 11 (level, low) -> IRQ 11 [ 31.967275] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 31.967278] ohci_hcd 0000:00:02.0: OHCI Host Controller [ 31.967417] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 [ 31.967433] ohci_hcd 0000:00:02.0: irq 11, io mem 0xdb001000 [ 31.997216] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.59. [ 32.045011] ieee1394: Initialized config rom entry `ip1394' [ 32.062643] usb usb1: configuration #1 chosen from 1 choice [ 32.062669] hub 1-0:1.0: USB hub found [ 32.062680] hub 1-0:1.0: 3 ports detected [ 32.165061] ACPI: PCI Interrupt Link [LUBB] enabled at IRQ 4 [ 32.165066] PCI: setting IRQ 4 as level-triggered [ 32.165070] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUBB] -> GSI 4 (level, low) -> IRQ 4 [ 32.165085] PCI: Setting latency timer of device 0000:00:02.1 to 64 [ 32.165088] ohci_hcd 0000:00:02.1: OHCI Host Controller [ 32.165187] ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2 [ 32.165204] ohci_hcd 0000:00:02.1: irq 4, io mem 0xdb002000 [ 32.222347] usb usb2: configuration #1 chosen from 1 choice [ 32.222373] hub 2-0:1.0: USB hub found [ 32.222384] hub 2-0:1.0: 3 ports detected [ 32.325085] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 3 [ 32.325090] PCI: setting IRQ 3 as level-triggered [ 32.325094] ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [LUB2] -> GSI 3 (level, low) -> IRQ 3 [ 32.325105] PCI: Setting latency timer of device 0000:00:02.2 to 64 [ 32.325109] ehci_hcd 0000:00:02.2: EHCI Host Controller [ 32.325134] ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3 [ 32.325171] ehci_hcd 0000:00:02.2: debug port 1 [ 32.325176] PCI: cache line size of 64 is not supported by device 0000:00:02.2 [ 32.325185] ehci_hcd 0000:00:02.2: irq 3, io mem 0xdb003000 [ 32.325192] ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 32.325270] usb usb3: configuration #1 chosen from 1 choice [ 32.325294] hub 3-0:1.0: USB hub found [ 32.325303] hub 3-0:1.0: 6 ports detected [ 32.428602] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 11 [ 32.428607] ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LMAC] -> GSI 11 (level, low) -> IRQ 11 [ 32.428613] PCI: Setting latency timer of device 0000:00:04.0 to 64 [ 32.948183] eth0: forcedeth.c: subsystem: 01043:80a7 bound to 0000:00:04.0 [ 32.948580] ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 7 [ 32.948583] PCI: setting IRQ 7 as level-triggered [ 32.948587] ACPI: PCI Interrupt 0000:01:09.2[B] -> Link [LNK3] -> GSI 7 (level, low) -> IRQ 7 [ 32.999244] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[7] MMIO=[da014000-da0147ff] Max Packet=[2048] IR/IT contexts=[4/8] [ 32.999392] NFORCE2: IDE controller at PCI slot 0000:00:09.0 [ 32.999413] NFORCE2: chipset revision 162 [ 32.999415] NFORCE2: not 100% native mode: will probe irqs later [ 32.999419] NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround. [ 32.999421] NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround. [ 32.999426] NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller [ 32.999435] ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA [ 32.999445] ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA [ 32.999453] Probing IDE interface ide0... [ 33.051779] usb 3-1: new high speed USB device using ehci_hcd and address 2 [ 33.287746] hda: Maxtor 6Y160P0, ATA DISK drive [ 33.571457] usb 3-1: device not accepting address 2, error -71 [ 33.735477] hdb: HL-DT-STDVD-ROM GDR8164B, ATAPI CD/DVD-ROM drive [ 33.792607] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 33.792873] Probing IDE interface ide1... [ 33.867282] usb 3-2: new high speed USB device using ehci_hcd and address 4 [ 33.999577] usb 3-2: configuration #1 chosen from 1 choice [ 33.999661] hub 3-2:1.0: USB hub found [ 33.999763] hub 3-2:1.0: 4 ports detected [ 34.079273] hdc: WDC WD1600JB-00EVA0, ATA DISK drive [ 34.267165] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023c0151085f89] [ 34.343004] usb 3-5: new high speed USB device using ehci_hcd and address 5 [ 34.485798] usb 3-5: configuration #1 chosen from 1 choice [ 34.527005] hdd: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive [ 34.586191] ide1 at 0x170-0x177,0x376 on irq 15 [ 34.592142] SCSI subsystem initialized [ 34.596143] libata version 2.00 loaded. [ 34.604978] hda: max request size: 512KiB [ 34.617323] hda: 320173056 sectors (163928 MB) w/7936KiB Cache, CHS=19929/255/63, UDMA(133) [ 34.619440] hda: cache flushes supported [ 34.619483] hda: hda1 hda2 hda3 hda4 < hda5 > [ 34.652290] hdc: max request size: 512KiB [ 34.653794] hdb: ATAPI 52X DVD-ROM drive, 256kB Cache, UDMA(33) [ 34.653800] Uniform CD-ROM driver Revision: 3.20 [ 34.668655] hdc: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA(100) [ 34.670312] hdc: cache flushes supported [ 34.670332] hdc: hdc1 < hdc5 hdc6 > [ 34.714317] hdd: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33) [ 34.786764] usb 1-1: new full speed USB device using ohci_hcd and address 3 [ 34.888019] Attempting manual resume [ 34.888023] swsusp: Resume From Partition 3:3 [ 34.888024] PM: Checking swsusp image. [ 34.888256] PM: Resume from disk failed. [ 34.910136] kjournald starting. Commit interval 5 seconds [ 34.910148] EXT3-fs: mounted filesystem with ordered data mode. [ 34.966630] usb 1-1: device descriptor read/64, error -62 [ 35.250453] usb 1-1: device descriptor read/64, error -62 [ 35.530290] usb 1-1: new full speed USB device using ohci_hcd and address 4 [ 35.710184] usb 1-1: device descriptor read/64, error -62 [ 35.994011] usb 1-1: device descriptor read/64, error -62 [ 36.273835] usb 1-1: new full speed USB device using ohci_hcd and address 5 [ 36.681590] usb 1-1: device not accepting address 5, error -62 [ 36.857482] usb 1-1: new full speed USB device using ohci_hcd and address 6 [ 37.265235] usb 1-1: device not accepting address 6, error -62 [ 37.265364] hub 3-2:1.0: hub_port_status failed (err = -71) [ 37.265609] hub 3-2:1.0: hub_port_status failed (err = -71) [ 37.265859] hub 3-2:1.0: hub_port_status failed (err = -71) [ 37.266108] hub 3-2:1.0: hub_port_status failed (err = -71) [ 37.313604] usbcore: registered new interface driver libusual [ 37.596023] Initializing USB Mass Storage driver... [ 37.653158] usb 3-2.1: new low speed USB device using ehci_hcd and address 6 [ 37.786734] usb 3-2.1: configuration #1 chosen from 1 choice [ 38.000862] usb 3-2.2: new high speed USB device using ehci_hcd and address 7 [ 38.110578] usb 3-2.2: configuration #1 chosen from 1 choice [ 38.110911] hub 3-2.2:1.0: USB hub found [ 38.111265] hub 3-2.2:1.0: 4 ports detected [ 38.216888] scsi0 : SCSI emulation for USB Mass Storage devices [ 38.216927] usb-storage: device found at 5 [ 38.216930] usb-storage: waiting for device to settle before scanning [ 38.217805] usbcore: registered new interface driver usb-storage [ 38.217808] USB Mass Storage support registered. [ 43.213826] usb-storage: device scan complete [ 43.325607] usb 3-5: reset high speed USB device using ehci_hcd and address 5 [ 43.437543] usb 3-5: device descriptor read/64, error -71 [ 43.653418] usb 3-5: device descriptor read/64, error -71 [ 43.869278] usb 3-5: reset high speed USB device using ehci_hcd and address 5 [ 43.981209] usb 3-5: device descriptor read/64, error -71 [ 44.197079] usb 3-5: device descriptor read/64, error -71 [ 44.279611] i2c_adapter i2c-0: nForce2 SMBus adapter at 0x5000 [ 44.279640] i2c_adapter i2c-1: nForce2 SMBus adapter at 0x5500 [ 44.412952] usb 3-5: reset high speed USB device using ehci_hcd and address 5 [ 44.586504] Linux agpgart interface v0.101 (c) Dave Jones [ 44.594227] NET: Registered protocol family 17 [ 44.820702] usb 3-5: device not accepting address 5, error -71 [ 44.820725] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 44.822213] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 44.851014] agpgart: Detected NVIDIA nForce2 chipset [ 44.864743] agpgart: AGP aperture is 256M @ 0xc0000000 [ 44.932653] usb 3-5: reset high speed USB device using ehci_hcd and address 5 [ 45.254741] input: PC Speaker as /class/input/input1 [ 45.284966] gameport: EMU10K1 is pci0000:01:09.1/gameport0, io 0xd400, speed 903kHz [ 45.340385] usb 3-5: device not accepting address 5, error -71 [ 45.340445] usb 3-5: USB disconnect, address 5 [ 45.352384] usbcore: registered new interface driver hiddev [ 45.366408] b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully [ 45.367480] flexcop-pci: will use the HW PID filter. [ 45.367485] flexcop-pci: card revision 1 [ 45.367769] ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 10 [ 45.367773] PCI: setting IRQ 10 as level-triggered [ 45.367776] ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [LNK1] -> GSI 10 (level, low) -> IRQ 10 [ 45.380384] DVB: registering new adapter (FlexCop Digital TV device). [ 45.381906] b2c2-flexcop: MAC address = 00:d0:d7:01:e6:db [ 45.381915] **WARNING** I2C adapter driver [B2C2 FlexCop device] forgot to specify physical device; fix it! [ 45.464317] usb 3-5: new high speed USB device using ehci_hcd and address 8 [ 45.574230] nvidia: module license 'NVIDIA' taints kernel. [ 45.577970] usb 3-5: device descriptor read/64, error -71 [ 45.827114] b2c2-flexcop: found the stv0299 at i2c address: 0x68 [ 45.827121] DVB: registering frontend 0 (ST STV0299 DVB-S)... [ 45.827175] b2c2-flexcop: initialization of 'Sky2PC/SkyStar 2 DVB-S' at the 'PCI' bus controlled by a 'FlexCopII' complete [ 45.892572] ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 12 [ 45.892577] PCI: setting IRQ 12 as level-triggered [ 45.892581] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNK4] -> GSI 12 (level, low) -> IRQ 12 [ 45.892933] NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-9631 Thu Nov 9 17:38:10 PST 2006 [ 45.940817] usb 3-5: device descriptor read/64, error -71 [ 46.100400] ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 5 [ 46.100406] PCI: setting IRQ 5 as level-triggered [ 46.100409] ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [LNK2] -> GSI 5 (level, low) -> IRQ 5 [ 46.108429] Installing spdif_bug patch: Audigy 2 ZS [SB0350] [ 46.155909] usb 3-5: new high speed USB device using ehci_hcd and address 9 [ 46.267821] usb 3-5: device descriptor read/64, error -71 [ 46.483692] usb 3-5: device descriptor read/64, error -71 [ 46.699565] usb 3-5: new high speed USB device using ehci_hcd and address 10 [ 47.107318] usb 3-5: device not accepting address 10, error -71 [ 47.219253] usb 3-5: new high speed USB device using ehci_hcd and address 11 [ 47.627010] usb 3-5: device not accepting address 11, error -71 [ 47.726674] input: KYE Systems Corp. Wireless Keyboard & Mouse as /class/input/input2 [ 47.726814] input: USB HID v1.10 Keyboard [KYE Systems Corp. Wireless Keyboard & Mouse] on usb-0000:00:02.2-2.1 [ 47.731556] input: KYE Systems Corp. Wireless Keyboard & Mouse as /class/input/input3 [ 47.731897] input: USB HID v1.10 Mouse [KYE Systems Corp. Wireless Keyboard & Mouse] on usb-0000:00:02.2-2.1 [ 47.731909] usbcore: registered new interface driver usbhid [ 47.731913] drivers/usb/input/hid-core.c: v2.6:USB HID core driver [ 48.169354] lp: driver loaded but no devices found [ 48.222261] fuse init (API version 7.8) [ 48.252437] Adding 530136k swap on /dev/disk/by-uuid/63feb4bc-2e39-4e6e-8ed2-c78cf2137342. Priority:-1 extents:1 across:530136k [ 48.304191] EXT3 FS on hda2, internal journal [ 48.632665] NET: Registered protocol family 10 [ 48.632761] lo: Disabled Privacy Extensions [ 48.719522] kjournald starting. Commit interval 5 seconds [ 48.758654] EXT3 FS on hda5, internal journal [ 48.758660] EXT3-fs: mounted filesystem with ordered data mode. [ 48.790655] kjournald starting. Commit interval 5 seconds [ 48.791017] EXT3 FS on hdc5, internal journal [ 48.791022] EXT3-fs: mounted filesystem with ordered data mode. [ 48.820228] kjournald starting. Commit interval 5 seconds [ 48.820551] EXT3 FS on hdc6, internal journal [ 48.820556] EXT3-fs: mounted filesystem with ordered data mode. [ 54.144722] input: Power Button (FF) as /class/input/input4 [ 54.167384] ACPI: Power Button (FF) [PWRF] [ 54.207081] input: Power Button (CM) as /class/input/input5 [ 54.207300] ACPI: Power Button (CM) [PWRB] [ 54.260298] Using specific hotkey driver [ 54.293768] No dock devices found. [ 54.331581] ibm_acpi: ec object not found [ 56.627940] agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0. [ 56.627957] agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode [ 56.628009] agpgart: Putting AGP V3 device at 0000:02:00.0 into 8x mode [ 57.484869] **WARNING** I2C adapter driver [NVIDIA i2c adapter 0 at 2:00.0] forgot to specify physical device; fix it! [ 57.485410] **WARNING** I2C adapter driver [NVIDIA i2c adapter 1 at 2:00.0] forgot to specify physical device; fix it! [ 57.485707] **WARNING** I2C adapter driver [NVIDIA i2c adapter 2 at 2:00.0] forgot to specify physical device; fix it! [ 57.727109] ppdev: user-space parallel port driver [ 59.267993] eth0: no IPv6 routers present [ 60.111557] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) [ 60.111562] apm: overridden by ACPI. [ 69.999363] vboxdrv: Trying to deactivate NMI watchdog permanently... [ 69.999369] vboxdrv: NMI watchdog either active or at least initialized. Please disable the NMI [ 69.999370] vboxdrv: watchdog by specifying 'nmi_watchdog=0' at kernel command line. [ 70.924721] Bluetooth: Core ver 2.11 [ 70.924781] NET: Registered protocol family 31 [ 70.924783] Bluetooth: HCI device and connection manager initialized [ 70.924786] Bluetooth: HCI socket layer initialized [ 71.162988] Bluetooth: L2CAP ver 2.8 [ 71.162993] Bluetooth: L2CAP socket layer initialized [ 71.376717] usb 1-1: new full speed USB device using ohci_hcd and address 7 [ 71.560602] usb 1-1: device descriptor read/64, error -62 [ 71.848426] usb 1-1: device descriptor read/64, error -62 [ 72.128257] usb 1-1: new full speed USB device using ohci_hcd and address 8 [ 72.312141] usb 1-1: device descriptor read/64, error -62 [ 72.599979] usb 1-1: device descriptor read/64, error -62 [ 72.879815] usb 1-1: new full speed USB device using ohci_hcd and address 9 [ 73.287552] usb 1-1: device not accepting address 9, error -62 [ 73.463454] usb 1-1: new full speed USB device using ohci_hcd and address 10 [ 73.871213] usb 1-1: device not accepting address 10, error -62 [ 74.102441] Bluetooth: RFCOMM socket layer initialized [ 74.102455] Bluetooth: RFCOMM TTY layer initialized [ 74.102457] Bluetooth: RFCOMM ver 1.8 [ 81.958327] eth0: no IPv6 routers present