ok here is the info you need:
ubuntu@ubuntu:~$ lspci -vvnn
00:00.0 Host bridge [0600]: Intel Corporation 82850 850 (Tehama) Chipset Host Bridge (MCH) [8086:2530] (rev 04)
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
        Latency: 0
        Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
        Capabilities: <access denied>

00:01.0 PCI bridge [0604]: Intel Corporation 82850 850 (Tehama) Chipset AGP Bridge [8086:2532] (rev 04) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
        I/O behind bridge: 0000c000-0000cfff
        Memory behind bridge: ff800000-ff8fffff
        Prefetchable memory behind bridge: 9e900000-de9fffff
        Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 04) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
        I/O behind bridge: 0000d000-0000dfff
        Memory behind bridge: ff900000-ff9fffff
        Prefetchable memory behind bridge: dea00000-deafffff
        Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-

00:1f.0 ISA bridge [0601]: Intel Corporation 82801BA ISA Bridge (LPC) [8086:2440] (rev 04)
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0

00:1f.1 IDE interface [0101]: Intel Corporation 82801BA IDE U100 Controller [8086:244b] (rev 04) (prog-if 80 [Master])
        Subsystem: Intel Corporation Unknown device [8086:4d44]
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
        Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
        Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
        Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
        Region 4: I/O ports at ffa0 [size=16]

00:1f.2 USB Controller [0c03]: Intel Corporation 82801BA/BAM USB Controller #1 [8086:2442] (rev 04) (prog-if 00 [UHCI])
        Subsystem: Intel Corporation Unknown device [8086:4d44]
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin D routed to IRQ 16
        Region 4: I/O ports at ef40 [size=32]

00:1f.3 SMBus [0c05]: Intel Corporation 82801BA/BAM SMBus Controller [8086:2443] (rev 04)
        Subsystem: Intel Corporation Unknown device [8086:4d44]
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin B routed to IRQ 10
        Region 4: I/O ports at efa0 [size=16]

00:1f.4 USB Controller [0c03]: Intel Corporation 82801BA/BAM USB Controller #1 [8086:2444] (rev 04) (prog-if 00 [UHCI])
        Subsystem: Intel Corporation Unknown device [8086:4d44]
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin C routed to IRQ 17
        Region 4: I/O ports at ef80 [size=32]

01:00.0 VGA compatible controller [0300]: ATI Technologies Inc RV350 AS [Radeon 9550] [1002:4153] (prog-if 00 [VGA])
        Subsystem: ATI Technologies Inc Unknown device [1002:0402]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (2000ns min), Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 21
        Region 0: Memory at c0000000 (32-bit, prefetchable) [size=256M]
        Region 1: I/O ports at c800 [size=256]
        Region 2: Memory at ff8f0000 (32-bit, non-prefetchable) [size=64K]
        Expansion ROM at ff8c0000 [disabled] [size=128K]
        Capabilities: <access denied>

01:00.1 Display controller [0380]: ATI Technologies Inc RV350 AS [Radeon 9550] (Secondary) [1002:4173]
        Subsystem: ATI Technologies Inc Unknown device [1002:0403]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (2000ns min), Cache Line Size: 32 bytes
        Region 0: Memory at b0000000 (32-bit, prefetchable) [size=256M]
        Region 1: Memory at ff8e0000 (32-bit, non-prefetchable) [size=64K]
        Capabilities: <access denied>

02:08.0 Ethernet controller [0200]: Intel Corporation 82801BA/BAM/CA/CAM Ethernet Controller [8086:2449] (rev 03)
        Subsystem: Intel Corporation EtherExpress PRO/100 VE [8086:3013]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 18
        Region 0: Memory at ff9ff000 (32-bit, non-prefetchable) [size=4K]
        Region 1: I/O ports at df00 [size=64]
        Capabilities: <access denied>

02:09.0 Ethernet controller [0200]: ADMtek NC100 Network Everywhere Fast Ethernet 10/100 [1317:0985] (rev 11)
        Subsystem: ADMtek Unknown device [1317:0570]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (16000ns min, 32000ns max), Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 19
        Region 0: I/O ports at d800 [size=256]
        Region 1: Memory at ff9fec00 (32-bit, non-prefetchable) [size=1K]
        Expansion ROM at dea00000 [disabled] [size=128K]
        Capabilities: <access denied>

02:0a.0 Communication controller [0780]: Conexant HSF 56k HSFi Modem [14f1:2f00] (rev 01)
        Subsystem: Zoom Telephonics Inc Unknown device [141b:8d88]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32
        Interrupt: pin A routed to IRQ 3
        Region 0: Memory at ff9e0000 (32-bit, non-prefetchable) [size=64K]
        Region 1: I/O ports at dfe0 [size=8]
        Capabilities: <access denied>

02:0c.0 Multimedia audio controller [0401]: Creative Labs SB Audigy [1102:0004] (rev 03)
        Subsystem: Creative Labs SB0090 Audigy Player/OEM [1102:0053]
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (500ns min, 5000ns max)
        Interrupt: pin A routed to IRQ 20
        Region 0: I/O ports at df80 [size=32]
        Capabilities: <access denied>

02:0c.1 Input device controller [0980]: Creative Labs SB Audigy Game Port [1102:7003] (rev 03)
        Subsystem: Creative Labs SB Audigy MIDI/Game Port [1102:0040]
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32
        Region 0: I/O ports at dff0 [size=8]
        Capabilities: <access denied>

02:0c.2 FireWire (IEEE 1394) [0c00]: Creative Labs SB Audigy FireWire Port [1102:4001] (prog-if 10 [OHCI])
        Subsystem: Creative Labs SB Audigy FireWire Port [1102:0010]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (500ns min, 1000ns max), Cache Line Size: 32 bytes
        Interrupt: pin B routed to IRQ 19
        Region 0: Memory at ff9fe000 (32-bit, non-prefetchable) [size=2K]
        Region 1: Memory at ff9f8000 (32-bit, non-prefetchable) [size=16K]
        Capabilities: <access denied>

ubuntu@ubuntu:~$ dmesg
[    0.000000] Linux version 2.6.22-14-generic (buildd@palmer) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun Oct 14 23:05:12 GMT 2007 (Ubuntu 2.6.22-14.46-generic)
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 0000000000097c00 (usable)
[    0.000000]  BIOS-e820: 0000000000097c00 - 0000000000098000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000001ffc0000 (usable)
[    0.000000]  BIOS-e820: 000000001ffc0000 - 000000001fff8000 (ACPI data)
[    0.000000]  BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
[    0.000000]  BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[    0.000000] 0MB HIGHMEM available.
[    0.000000] 511MB LOWMEM available.
[    0.000000] Entering add_active_range(0, 0, 131008) 0 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->   131008
[    0.000000]   HighMem    131008 ->   131008
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->   131008
[    0.000000] On node 0 totalpages: 131008
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4064 pages, LIFO batch:0
[    0.000000]   Normal zone: 991 pages used for memmap
[    0.000000]   Normal zone: 125921 pages, LIFO batch:31
[    0.000000]   HighMem zone: 0 pages used for memmap
[    0.000000] DMI 2.3 present.
[    0.000000] ACPI: RSDP signature @ 0xC00FF980 checksum 0
[    0.000000] ACPI: RSDP 000FF980, 0014 (r0 AMI   )
[    0.000000] ACPI: RSDT 1FFF0000, 002C (r1 D850MV MV85010A 20020724 MSFT     1011)
[    0.000000] ACPI: FACP 1FFF1000, 0074 (r1 D850MV MV85010A 20020724 MSFT     1011)
[    0.000000] ACPI: DSDT 1FFE0000, 3816 (r1 D850MV MV85010A        6 MSFT  100000B)
[    0.000000] ACPI: FACS 1FFF8000, 0040
[    0.000000] ACPI: APIC 1FFE3816, 0068 (r1 D850MV MV85010A 20020724 MSFT     1011)
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] Processor #0 15:2 APIC version 20
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
[    0.000000] Built 1 zonelists.  Total pages: 129985
[    0.000000] Kernel command line: BOOT_IMAGE=/casper/vmlinuz file=/cdrom/preseed/ubuntu.seed boot=casper initrd=/casper/initrd.gz quiet splash --
[    0.000000] mapped APIC to ffffd000 (fee00000)
[    0.000000] mapped IOAPIC to ffffc000 (fec00000)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[    0.000000] Detected 1993.973 MHz processor.
[   88.523616] Console: colour VGA+ 80x25
[   88.524012] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[   88.524375] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[   88.541347] Memory: 507756k/524032k available (2015k kernel code, 15676k reserved, 916k data, 364k init, 0k highmem)
[   88.541361] virtual kernel memory layout:
[   88.541364]     fixmap  : 0xfff4d000 - 0xfffff000   ( 712 kB)
[   88.541366]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[   88.541367]     vmalloc : 0xe0800000 - 0xff7fe000   ( 495 MB)
[   88.541369]     lowmem  : 0xc0000000 - 0xdffc0000   ( 511 MB)
[   88.541370]       .init : 0xc03e3000 - 0xc043e000   ( 364 kB)
[   88.541372]       .data : 0xc02f7d26 - 0xc03dce84   ( 916 kB)
[   88.541373]       .text : 0xc0100000 - 0xc02f7d26   (2015 kB)
[   88.541377] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[   88.541427] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[   88.621370] Calibrating delay using timer specific routine.. 3991.97 BogoMIPS (lpj=7983957)
[   88.621403] Security Framework v1.0.0 initialized
[   88.621412] SELinux:  Disabled at boot.
[   88.621429] Mount-cache hash table entries: 512
[   88.621615] CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000 00000000 00000000 00000000
[   88.621631] CPU: Trace cache: 12K uops, L1 D cache: 8K
[   88.621635] CPU: L2 cache: 512K
[   88.621638] CPU: Hyper-Threading is disabled
[   88.621642] CPU: After all inits, caps: 3febfbff 00000000 00000000 0000b080 00000000 00000000 00000000
[   88.621656] Compat vDSO mapped to ffffe000.
[   88.621673] Checking 'hlt' instruction... OK.
[   88.637551] SMP alternatives: switching to UP code
[   88.637830] Freeing SMP alternatives: 11k freed
[   88.638263] Early unpacking initramfs... done
[   89.081297] ACPI: Core revision 20070126
[   89.081374] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[   89.084481] CPU0: Intel(R) Pentium(R) 4 CPU 2.00GHz stepping 04
[   89.084529] Total of 1 processors activated (3991.97 BogoMIPS).
[   89.084673] ENABLING IO-APIC IRQs
[   89.084871] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[   89.228816] Brought up 1 CPUs
[   89.228982] Booting paravirtualized kernel on bare hardware
[   89.229064] Time: 15:57:54  Date: 01/08/108
[   89.229095] NET: Registered protocol family 16
[   89.229223] EISA bus registered
[   89.229240] ACPI: bus type pci registered
[   89.229396] PCI: PCI BIOS revision 2.10 entry at 0xfda95, last bus=2
[   89.229399] PCI: Using configuration type 1
[   89.229402] Setting up standard PCI resources
[   89.231556] ACPI: EC: Look up EC in DSDT
[   89.236383] ACPI: Interpreter enabled
[   89.236389] ACPI: (supports S0 S1 S4 S5)
[   89.236416] ACPI: Using IOAPIC for interrupt routing
[   89.243287] ACPI: PCI Root Bridge [PCI0] (0000:00)
[   89.243314] PCI: Probing PCI hardware (bus 00)
[   89.243574] PCI quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO
[   89.243579] PCI quirk: region 0500-053f claimed by ICH4 GPIO
[   89.244097] PCI: Firmware left 0000:02:08.0 e100 interrupts enabled, disabling
[   89.244496] PCI: Transparent bridge - 0000:00:1e.0
[   89.244530] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[   89.244643] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
[   89.253308] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[   89.253437] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[   89.253560] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[   89.253686] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[   89.253810] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[   89.253934] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
[   89.254058] ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
[   89.254182] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[   89.254326] ACPI: Power Resource [FDDP] (off)
[   89.254366] ACPI: Power Resource [URP1] (off)
[   89.254405] ACPI: Power Resource [URP2] (off)
[   89.254443] ACPI: Power Resource [LPTP] (off)
[   89.254460] Linux Plug and Play Support v0.97 (c) Adam Belay
[   89.254477] pnp: PnP ACPI init
[   89.254490] ACPI: bus type pnp registered
[   89.257655] pnp: PnP ACPI: found 12 devices
[   89.257659] ACPI: ACPI bus type pnp unregistered
[   89.257666] PnPBIOS: Disabled by ACPI PNP
[   89.257742] PCI: Using ACPI for IRQ routing
[   89.257747] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[   89.262956] NET: Registered protocol family 8
[   89.262960] NET: Registered protocol family 20
[   89.263069] pnp: 00:0b: iomem range 0x0-0x9ffff could not be reserved
[   89.263073] pnp: 00:0b: iomem range 0xe8000-0xfffff could not be reserved
[   89.263077] pnp: 00:0b: iomem range 0x100000-0x1fffffff could not be reserved
[   89.263081] pnp: 00:0b: iomem range 0xfec00000-0xfec00fff could not be reserved
[   89.264731] Time: tsc clocksource has been installed.
[   89.293499] PCI: Bridge: 0000:00:01.0
[   89.293503]   IO window: c000-cfff
[   89.293509]   MEM window: ff800000-ff8fffff
[   89.293514]   PREFETCH window: 9e900000-de9fffff
[   89.293523] PCI: Bridge: 0000:00:1e.0
[   89.293527]   IO window: d000-dfff
[   89.293534]   MEM window: ff900000-ff9fffff
[   89.293539]   PREFETCH window: dea00000-deafffff
[   89.293560] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[   89.293581] NET: Registered protocol family 2
[   89.332718] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[   89.332776] TCP established hash table entries: 16384 (order: 5, 196608 bytes)
[   89.332932] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[   89.333038] TCP: Hash tables configured (established 16384 bind 16384)
[   89.333042] TCP reno registered
[   89.344832] checking if image is initramfs... it is
[   89.796193] Switched to high resolution mode on CPU 0
[   90.215854] Freeing initrd memory: 7305k freed
[   90.216319] audit: initializing netlink socket (disabled)
[   90.216339] audit(1202486274.120:1): initialized
[   90.219289] VFS: Disk quotas dquot_6.5.1
[   90.219365] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   90.219503] io scheduler noop registered
[   90.219506] io scheduler anticipatory registered
[   90.219509] io scheduler deadline registered
[   90.219532] io scheduler cfq registered (default)
[   90.219586] Boot video device is 0000:01:00.0
[   90.219831] isapnp: Scanning for PnP cards...
[   90.573771] isapnp: No Plug & Play device found
[   90.612708] Real Time Clock Driver v1.12ac
[   90.612839] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[   90.612947] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[   90.614150] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[   90.615299] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[   90.615603] input: Macintosh mouse button emulation as /class/input/input0
[   90.615725] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[   90.619463] serio: i8042 KBD port at 0x60,0x64 irq 1
[   90.619473] serio: i8042 AUX port at 0x60,0x64 irq 12
[   90.619743] mice: PS/2 mouse device common for all mice
[   90.619904] EISA: Probing bus 0 at eisa.0
[   90.619946] EISA: Detected 0 cards.
[   90.620082] TCP cubic registered
[   90.620099] NET: Registered protocol family 1
[   90.620131] Using IPI No-Shortcut mode
[   90.620352]   Magic number: 12:607:992
[   90.620372]   hash matches device ttyd5
[   90.621082] Freeing unused kernel memory: 364k freed
[   90.663239] input: AT Translated Set 2 keyboard as /class/input/input1
[   91.911656] AppArmor: AppArmor initialized<5>audit(1202486276.120:2):  type=1505 info="AppArmor initialized" pid=1177
[   91.923934] fuse init (API version 7.8)
[   91.932092] Failure registering capabilities with primary security module.
[   91.952197] ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device is not present [20070126]
[   92.823690] SCSI subsystem initialized
[   92.831607] libata version 2.21 loaded.
[   92.836806] ata_piix 0000:00:1f.1: version 2.11
[   92.836876] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[   92.836988] scsi0 : ata_piix
[   92.837051] scsi1 : ata_piix
[   92.837196] ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001ffa0 irq 14
[   92.837200] ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001ffa8 irq 15
[   92.849773] usbcore: registered new interface driver usbfs
[   92.849811] usbcore: registered new interface driver hub
[   92.849844] usbcore: registered new device driver usb
[   92.851122] USB Universal Host Controller Interface driver v3.0
[   93.006665] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
[   93.006670] e100: Copyright(c) 1999-2006 Intel Corporation
[   93.167331] Linux Tulip driver version 1.1.15 (Feb 27, 2007)
[   93.174604] Floppy drive(s): fd0 is 1.44M
[   93.195587] FDC 0 is a post-1991 82077
[   94.247141] end_request: I/O error, dev fd0, sector 0
[   95.289967] end_request: I/O error, dev fd0, sector 0
[   96.332796] end_request: I/O error, dev fd0, sector 0
[   97.375624] end_request: I/O error, dev fd0, sector 0
[   98.026879] ata1: port is slow to respond, please be patient (Status 0x80)
[   98.418452] end_request: I/O error, dev fd0, sector 0
[   99.461278] end_request: I/O error, dev fd0, sector 0
[  100.504105] end_request: I/O error, dev fd0, sector 0
[  101.546932] end_request: I/O error, dev fd0, sector 0
[  102.589760] end_request: I/O error, dev fd0, sector 0
[  102.837470] ata1: SRST failed (errno=-16)
[  103.632588] end_request: I/O error, dev fd0, sector 0
[  103.660767] ata2.00: ATAPI: LITE-ON DVD SOHD-16P9S, FS09, max UDMA/33
[  103.660776] ata2.01: ATAPI: LITE-ON DVDRW LH-20A1P, KL0N, max UDMA/66
[  103.660784] ata2.01: limited to UDMA/33 due to 40-wire cable
[  103.832565] ata2.00: configured for UDMA/33
[  104.020352] ata2.01: configured for UDMA/33
[  104.023606] scsi 1:0:0:0: CD-ROM            LITE-ON  DVD SOHD-16P9S   FS09 PQ: 0 ANSI: 5
[  104.025150] scsi 1:0:1:0: CD-ROM            LITE-ON  DVDRW LH-20A1P   KL0N PQ: 0 ANSI: 5
[  104.025697] ACPI: PCI Interrupt 0000:00:1f.2[D] -> GSI 19 (level, low) -> IRQ 16
[  104.025714] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[  104.025720] uhci_hcd 0000:00:1f.2: UHCI Host Controller
[  104.026128] uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
[  104.026166] uhci_hcd 0000:00:1f.2: irq 16, io base 0x0000ef40
[  104.026718] usb usb1: configuration #1 chosen from 1 choice
[  104.026917] hub 1-0:1.0: USB hub found
[  104.026926] hub 1-0:1.0: 2 ports detected
[  104.047674] sr0: scsi3-mmc drive: 62x/62x cd/rw xa/form2 cdda tray
[  104.047682] Uniform CD-ROM driver Revision: 3.20
[  104.047948] sr 1:0:0:0: Attached scsi CD-ROM sr0
[  104.055383] sr1: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[  104.055632] sr 1:0:1:0: Attached scsi CD-ROM sr1
[  104.061343] sr 1:0:0:0: Attached scsi generic sg0 type 5
[  104.061373] sr 1:0:1:0: Attached scsi generic sg1 type 5
[  104.128217] ACPI: PCI Interrupt 0000:00:1f.4[C] -> GSI 23 (level, low) -> IRQ 17
[  104.128235] PCI: Setting latency timer of device 0000:00:1f.4 to 64
[  104.128240] uhci_hcd 0000:00:1f.4: UHCI Host Controller
[  104.128275] uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
[  104.128310] uhci_hcd 0000:00:1f.4: irq 17, io base 0x0000ef80
[  104.128450] usb usb2: configuration #1 chosen from 1 choice
[  104.128487] hub 2-0:1.0: USB hub found
[  104.128500] hub 2-0:1.0: 2 ports detected
[  104.232201] ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 20 (level, low) -> IRQ 18
[  104.256265] e100: eth0: e100_probe: addr 0xff9ff000, irq 18, MAC addr 00:03:47:EC:44:74
[  104.256826] ACPI: PCI Interrupt 0000:02:0c.2[B] -> GSI 21 (level, low) -> IRQ 19
[  104.308758] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19]  MMIO=[ff9fe000-ff9fe7ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
[  104.313358] ACPI: PCI Interrupt 0000:02:09.0[A] -> GSI 21 (level, low) -> IRQ 19
[  104.314066] tulip0:  MII transceiver #1 config 3100 status 7869 advertising 05e1.
[  104.321331] eth1: ADMtek Comet rev 17 at Port 0xd800, 00:18:F8:0A:31:CE, IRQ 19.
[  104.367760] usb 1-1: new full speed USB device using uhci_hcd and address 2
[  104.529709] usb 1-1: configuration #1 chosen from 1 choice
[  104.533654] hub 1-1:1.0: USB hub found
[  104.536588] hub 1-1:1.0: 4 ports detected
[  104.679410] end_request: I/O error, dev fd0, sector 0
[  104.883189] usb 1-2: new low speed USB device using uhci_hcd and address 3
[  104.990200] ISO 9660 Extensions: Microsoft Joliet Level 3
[  105.022716] ISO 9660 Extensions: RRIP_1991A
[  105.066047] usb 1-2: configuration #1 chosen from 1 choice
[  105.170383] Registering unionfs 1.4
[  105.170387] unionfs: debugging is not enabled
[  105.180307] loop: module loaded
[  105.306704] usb 2-2: new full speed USB device using uhci_hcd and address 2
[  105.460817] usb 2-2: configuration #1 chosen from 1 choice
[  105.463756] hub 2-2:1.0: USB hub found
[  105.466689] hub 2-2:1.0: 4 ports detected
[  105.582552] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00023c0030034ec3]
[  105.583585] usbcore: registered new interface driver hiddev
[  105.598586] input: Microsoft Microsoft 5-Button Mouse with IntelliEye(TM) as /class/input/input2
[  105.598620] input: USB HID v1.10 Mouse [Microsoft Microsoft 5-Button Mouse with IntelliEye(TM)] on usb-0000:00:1f.2-2
[  105.598641] usbcore: registered new interface driver usbhid
[  105.598647] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[  105.754233] squashfs: version 3.2-UBUNTU (2007/07/26) Phillip Lougher
[  156.861731] Linux agpgart interface v0.102 (c) Dave Jones
[  156.978855] agpgart: Detected an Intel i850 Chipset.
[  156.993379] agpgart: AGP aperture is 256M @ 0xe0000000
[  157.102440] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[  157.211269] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[  157.260100] iTCO_vendor_support: vendor-support=0
[  157.261355] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
[  157.261441] iTCO_wdt: failed to reset NO_REBOOT flag, reboot disabled by hardware
[  157.261452] iTCO_wdt: No card detected
[  157.304496] intel_rng: Firmware space is locked read-only. <4>intel_rng: If you can't or
[  157.304500]  don't want to <4>intel_rng: disable this in firmware setup, and <4>intel_rng: if
[  157.304503]  you are certain that your <4>intel_rng: system has a functional
[  157.304504]  RNG, try<4>intel_rng: using the 'no_fwh_detect' option.
[  157.753654] parport_pc 00:09: reported by Plug and Play ACPI
[  157.753710] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[  157.940198] input: PC Speaker as /class/input/input3
[  158.981083] gameport: EMU10K1 is pci0000:02:0c.1/gameport0, io 0xdff0, speed 962kHz
[  159.569490] ACPI: PCI Interrupt 0000:02:0c.0[A] -> GSI 17 (level, low) -> IRQ 20
[  164.002047] No dock devices found.
[  164.098909] input: Power Button (FF) as /class/input/input4
[  164.104855] ACPI: Power Button (FF) [PWRF]
[  164.158196] input: Power Button (CM) as /class/input/input5
[  164.164210] ACPI: Power Button (CM) [PBTN]
[  168.822700] lp0: using parport0 (interrupt-driven).
[  168.875987] ppdev: user-space parallel port driver
[  170.393711] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[  170.393718] apm: overridden by ACPI.
[  170.823377] Failure registering capabilities with primary security module.
[  171.587209] Bluetooth: Core ver 2.11
[  171.587513] NET: Registered protocol family 31
[  171.587517] Bluetooth: HCI device and connection manager initialized
[  171.587521] Bluetooth: HCI socket layer initialized
[  171.746183] Bluetooth: L2CAP ver 2.8
[  171.746189] Bluetooth: L2CAP socket layer initialized
[  171.809766] 0000:02:09.0: tulip_stop_rxtx() failed (CSR5 0xfc664010 CSR6 0xff972113)
[  171.809781] eth1: Setting full-duplex based on MII#1 link partner capability of 45e1.
[  171.911857] Bluetooth: RFCOMM socket layer initialized
[  171.912167] Bluetooth: RFCOMM TTY layer initialized
[  171.912172] Bluetooth: RFCOMM ver 1.8
[  176.734556] NET: Registered protocol family 17
[  177.804002] [drm] Initialized drm 1.1.0 20060810
[  177.856552] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 21
[  177.860086] [drm] Initialized radeon 1.27.0 20060524 on minor 0
[  180.142190] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[  180.142365] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[  180.142523] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[  180.423370] [drm] Setting GART location based on new memory map
[  180.423385] [drm] Loading R300 Microcode
[  180.423442] [drm] writeback test succeeded in 1 usecs
[  180.460363] NET: Registered protocol family 10
[  180.460587] lo: Disabled Privacy Extensions
[  180.460747] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  191.022299] eth1: no IPv6 routers present