ACPI: found 14 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically.  If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device().  As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior.  If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas@hp.com
** so I can fix the driver.
pnp: 00:01: ioport range 0xe400-0xe47f could not be reserved
pnp: 00:01: ioport range 0xe800-0xe81f has been reserved
pnp: 00:0d: ioport range 0x290-0x297 has been reserved
pnp: 00:0d: ioport range 0x370-0x375 has been reserved
Simple Boot Flag at 0x3a set to 0x1
audit: initializing netlink socket (disabled)
audit(1118337738.081:0): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
Restarting tasks...<6> Strange, kswapd0 not stopped
 Strange, kseriod not stopped
 done
ACPI wakeup devices: 
PCI0 PCI1 USB0 USB1 USB2 USB3 SU20 MC97 
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4556KiB [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 164k freed
NET: Registered protocol family 1
SCSI subsystem initialized
libata version 1.10 loaded.
sata_via version 1.1
ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
sata_via(0000:00:0f.0): routed to hard irq line 4
ata1: SATA max UDMA/133 cmd 0xB400 ctl 0xB002 bmdma 0xA000 irq 20
ata2: SATA max UDMA/133 cmd 0xA800 ctl 0xA402 bmdma 0xA008 irq 20
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:407f
ata1: dev 0 ATA, max UDMA/133, 312581808 sectors: lba48
ata1: dev 0 configured for UDMA/133
scsi0 : sata_via
ata2: no device found (phy stat 00000000)
scsi1 : sata_via
elevator: using anticipatory as default io scheduler
  Vendor: ATA       Model: ST3160827AS       Rev: 3.42
  Type:   Direct-Access                      ANSI SCSI revision: 05
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 0
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sda: drive cache: write back
 /dev/scsi/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 p7 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Stopping tasks: ==|
Freeing memory...  -\|/-done (424 pages freed)
Restarting tasks... done
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
Adding 996020k swap on /dev/sda2.  Priority:-1 extents:1
EXT3 FS on sda5, internal journal
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
Probing IDE interface ide1...
hdd: LITE-ON LTR-52327S, ATAPI CD/DVD-ROM drive
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
ide1 at 0x170-0x177,0x376 on irq 15
hdd: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
lp0: using parport0 (interrupt-driven).
mice: PS/2 mouse device common for all mice
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
ts: Compaq touchscreen protocol output
Capability LSM initialized
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: dm-devel@redhat.com
cdrom: open failed.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Real Time Clock Driver v1.12
input: PC Speaker
inserting floppy driver for 2.6.10-5-k7
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: AGP aperture is 128M @ 0xf0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
PCI: Enabling device 0000:00:09.0 (0014 -> 0017)
ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 18 (level, low) -> IRQ 18
ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 18 (level, low) -> IRQ 18
eth0: 3Com Gigabit LOM (3C940)
      PrefPort:A  RlmtMode:Check Link State
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
    ide0: BM-DMA at 0x9400-0x9407, BIOS settings: hda:pio, hdb:pio
VP_IDE: port 0x0170 already claimed by ide1
Probing IDE interface ide0...
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:10.0: irq 21, io base 0x9000
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:00:10.1: irq 21, io base 0x8800
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
uhci_hcd 0000:00:10.2: irq 21, io base 0x8400
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#4)
uhci_hcd 0000:00:10.3: irq 21, io base 0x8000
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-2: new full speed USB device using uhci_hcd and address 2
Initializing USB Mass Storage driver...
eth0: network connection up using port A
    speed:           100
    autonegotiation: yes
    duplex mode:     full
    flowctrl:        symmetric
    irq moderation:  disabled
    scatter-gather:  enabled
usb 2-1: new low speed USB device using uhci_hcd and address 2
ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:10.4: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.4: irq 21, pci mem 0xd6000000
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
usb 1-2: string descriptor 0 read error: -71
usb 1-2: string descriptor 0 read error: -71
usb 1-2: string descriptor 0 read error: -71
scsi2 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usb 1-2: USB disconnect, address 2
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:11.5 to 64
usb 5-2: new high speed USB device using ehci_hcd and address 2
scsi3 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usb 5-7: new high speed USB device using ehci_hcd and address 4
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usb 2-1: new low speed USB device using uhci_hcd and address 3
usbcore: registered new driver hiddev
input: USB HID v1.10 Mouse [B16_b_02 USB-PS/2 Optical Mouse] on usb-0000:00:10.1-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
smbfs: Unrecognized mount option quiet
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0315d40(lo)
IPv6 over IPv4 tunneling driver
  Vendor: LITE-ON   Model: DVDRW SOHW-832S   Rev: VS08
  Type:   CD-ROM                             ANSI SCSI revision: 00
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr0 at scsi3, channel 0, id 0, lun 0
Attached scsi generic sg1 at scsi3, channel 0, id 0, lun 0,  type 5
usb-storage: device scan complete
  Vendor: 512MB     Model: USB2.0FlashDrive  Rev: 2.00
  Type:   Direct-Access                      ANSI SCSI revision: 02
SCSI device sdb: 1024000 512-byte hdwr sectors (524 MB)
sdb: Write Protect is off
sdb: Mode Sense: 03 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 1024000 512-byte hdwr sectors (524 MB)
sdb: Write Protect is off
sdb: Mode Sense: 03 00 00 00
sdb: assuming drive cache: write through
 /dev/scsi/host4/bus0/target0/lun0: p1
Attached scsi removable disk sdb at scsi4, channel 0, id 0, lun 0
Attached scsi generic sg2 at scsi4, channel 0, id 0, lun 0,  type 0
usb-storage: device scan complete
[drm] Initialized drm 1.0.0 20040925
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[drm] Initialized radeon 1.14.0 20050125 on minor 0: ATI Technologies Inc RV280 [Radeon 9200]
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 4x mode
[drm] Loading R200 Microcode
eth0: no IPv6 routers present
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
usb 5-7: USB disconnect, address 4
scsi4 (0:0): rejecting I/O to dead device
FAT bread failed in fat_clusters_flush
vmmon: module license 'unspecified' taints kernel.
/dev/vmmon[7905]: Module vmmon: registered with major=10 minor=165
/dev/vmmon[7905]: Module vmmon: initialized
/dev/vmmon[7925]: Module vmmon: unloaded
/dev/vmmon[8150]: Module vmmon: registered with major=10 minor=165
/dev/vmmon[8150]: Module vmmon: initialized
/dev/vmnet: open called by PID 8207 (vmnet-bridge)
/dev/vmnet: hub 0 does not exist, allocating memory.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: enabling the bridge
bridge-eth0: up
bridge-eth0: already up
bridge-eth0: attached
/dev/vmnet: open called by PID 8219 (vmnet-natd)
/dev/vmnet: hub 8 does not exist, allocating memory.
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 8225 (vmnet-netifup)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 8226 (vmnet-netifup)
/dev/vmnet: hub 1 does not exist, allocating memory.
/dev/vmnet: port on hub 1 successfully opened
/dev/vmnet: open called by PID 8250 (vmnet-dhcpd)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 8249 (vmnet-dhcpd)
/dev/vmnet: port on hub 1 successfully opened
vmnet1: no IPv6 routers present
vmnet8: no IPv6 routers present
/dev/vmnet: open called by PID 8302 (vmware-vmx)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmmon[8319]: host clock rate change request 0 -> 19
/dev/vmmon[8319]: host clock rate change request 19 -> 83
drivers/usb/input/hid-input.c: event field not found
drivers/usb/input/hid-input.c: event field not found
/dev/vmnet: open called by PID 8319 (vmware-vmx)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmmon[8319]: host clock rate change request 83 -> 19
/dev/vmmon[8302]: host clock rate change request 19 -> 0
vmmon: Had to deallocate locked 57894 pages from vm driver f7a99000
vmmon: Had to deallocate AWE 2465 pages from vm driver f7a99000
usb 5-1: new high speed USB device using ehci_hcd and address 5
usb 5-7: new high speed USB device using ehci_hcd and address 6
scsi5 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 6
usb-storage: waiting for device to settle before scanning
  Vendor: 512MB     Model: USB2.0FlashDrive  Rev: 2.00
  Type:   Direct-Access                      ANSI SCSI revision: 02
sdb: Unit Not Ready, sense:
Current : sense key Unit Attention
Additional sense: Not ready to ready change, medium may have changed
sdb : READ CAPACITY failed.
sdb : status=1, message=00, host=0, driver=08 
Current sd: sense key Unit Attention
Additional sense: Not ready to ready change, medium may have changed
sdb: test WP failed, assume Write Enabled
sdb: assuming drive cache: write through
SCSI device sdb: 1024000 512-byte hdwr sectors (524 MB)
sdb: Write Protect is off
sdb: Mode Sense: 03 00 00 00
sdb: assuming drive cache: write through
 /dev/scsi/host5/bus0/target0/lun0: p1
Attached scsi removable disk sdb at scsi5, channel 0, id 0, lun 0
Attached scsi generic sg2 at scsi5, channel 0, id 0, lun 0,  type 0
usb-storage: device scan complete
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
drivers/usb/input/hid-input.c: event field not found
drivers/usb/input/hid-input.c: event field not found
drivers/usb/input/hid-input.c: event field not found
drivers/usb/input/hid-input.c: event field not found