[ 0.000000] Linux version 2.6.22-14-generic (buildd@palmer) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun Oct 14 23:05:12 GMT 2007 (Ubuntu 2.6.22-14.46-generic) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e2000 - 00000000000e8000 (reserved) [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003f7f0000 (usable) [ 0.000000] BIOS-e820: 000000003f7f0000 - 000000003f7f8000 (ACPI data) [ 0.000000] BIOS-e820: 000000003f7f8000 - 000000003f800000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) [ 0.000000] 119MB HIGHMEM available. [ 0.000000] 896MB LOWMEM available. [ 0.000000] found SMP MP-table at 000fbc60 [ 0.000000] Entering add_active_range(0, 0, 260080) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] HighMem 229376 -> 260080 [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 260080 [ 0.000000] On node 0 totalpages: 260080 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1760 pages used for memmap [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 [ 0.000000] HighMem zone: 239 pages used for memmap [ 0.000000] HighMem zone: 30465 pages, LIFO batch:7 [ 0.000000] DMI 2.3 present. [ 0.000000] ACPI: RSDP signature @ 0xC00FA1A0 checksum 0 [ 0.000000] ACPI: RSDP 000FA1A0, 0014 (r0 COMPAQ) [ 0.000000] ACPI: RSDT 3F7F0000, 002C (r1 COMPAQ INTEL845 10 MSFT 97) [ 0.000000] ACPI: FACP 3F7F0030, 0081 (r1 COMPAQ INTEL845 11 MSFT 97) [ 0.000000] ACPI: DSDT 3F7F0120, 37B2 (r1 COMPAQ BROKDLEG 1000 INTL 2002024) [ 0.000000] ACPI: FACS 3F7F8000, 0040 [ 0.000000] ACPI: APIC 3F7F00C0, 005C (r1 COMPAQ INTEL845 9 MSFT 97) [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] Processor #0 15:2 APIC version 20 [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] disabled) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at 40000000 (gap: 3f800000:bf400000) [ 0.000000] Built 1 zonelists. Total pages: 258049 [ 0.000000] Kernel command line: root=UUID=2dad8304-4c01-4e82-b957-188c534d417c ro quiet splash [ 0.000000] mapped APIC to ffffd000 (fee00000) [ 0.000000] mapped IOAPIC to ffffc000 (fec00000) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Detected 2000.179 MHz processor. [ 27.947324] Console: colour VGA+ 80x25 [ 27.948297] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 27.949761] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 27.989933] Memory: 1019576k/1040320k available (2015k kernel code, 19920k reserved, 916k data, 364k init, 122816k highmem) [ 27.989948] virtual kernel memory layout: [ 27.989950] fixmap : 0xfff4d000 - 0xfffff000 ( 712 kB) [ 27.989952] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 27.989955] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) [ 27.989956] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 27.989958] .init : 0xc03e3000 - 0xc043e000 ( 364 kB) [ 27.989959] .data : 0xc02f7d26 - 0xc03dce84 ( 916 kB) [ 27.989961] .text : 0xc0100000 - 0xc02f7d26 (2015 kB) [ 27.989965] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 27.990037] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1 [ 28.069922] Calibrating delay using timer specific routine.. 4004.08 BogoMIPS (lpj=8008166) [ 28.069972] Security Framework v1.0.0 initialized [ 28.069986] SELinux: Disabled at boot. [ 28.070006] Mount-cache hash table entries: 512 [ 28.070265] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 [ 28.070285] CPU: Trace cache: 12K uops, L1 D cache: 8K [ 28.070289] CPU: L2 cache: 128K [ 28.070292] CPU: Hyper-Threading is disabled [ 28.070296] CPU: After all inits, caps: bfebfbff 00000000 00000000 0000b080 00004400 00000000 00000000 [ 28.070313] Compat vDSO mapped to ffffe000. [ 28.070336] Checking 'hlt' instruction... OK. [ 28.086062] SMP alternatives: switching to UP code [ 28.086480] Freeing SMP alternatives: 11k freed [ 28.086938] Early unpacking initramfs... done [ 28.520779] ACPI: Core revision 20070126 [ 28.520870] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found. [ 28.523553] CPU0: Intel(R) Celeron(R) CPU 2.00GHz stepping 09 [ 28.523609] Total of 1 processors activated (4004.08 BogoMIPS). [ 28.523749] ENABLING IO-APIC IRQs [ 28.523959] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 28.668907] Brought up 1 CPUs [ 28.669152] Booting paravirtualized kernel on bare hardware [ 28.669263] Time: 22:10:21 Date: 10/05/107 [ 28.669308] NET: Registered protocol family 16 [ 28.669529] EISA bus registered [ 28.669556] ACPI: bus type pci registered [ 28.671569] PCI: PCI BIOS revision 2.10 entry at 0xfdb61, last bus=3 [ 28.671572] PCI: Using configuration type 1 [ 28.671574] Setting up standard PCI resources [ 28.691067] ACPI: EC: Look up EC in DSDT [ 28.696434] ACPI: Interpreter enabled [ 28.696444] ACPI: (supports S0 S3 S4 S5) [ 28.696475] ACPI: Using IOAPIC for interrupt routing [ 28.708534] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 28.708554] PCI: Probing PCI hardware (bus 00) [ 28.709260] * The chipset may have PM-Timer Bug. Due to workarounds for a bug, [ 28.709263] * this clock source is slow. If you are sure your timer does not have [ 28.709265] * this bug, please use "acpi_pm_good" to disable the workaround [ 28.709319] PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO [ 28.709324] PCI quirk: region 0400-043f claimed by ICH4 GPIO [ 28.709763] PCI: Transparent bridge - 0000:00:1e.0 [ 28.709808] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 28.710022] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.ICHB._PRT] [ 28.729546] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15) [ 28.729720] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15) [ 28.729887] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15) [ 28.730097] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15) [ 28.730261] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 28.730427] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 28.730593] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 28.730813] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 11 12 14 15) [ 28.731128] ACPI: Power Resource [URP1] (off) [ 28.731189] ACPI: Power Resource [URP2] (off) [ 28.731245] ACPI: Power Resource [FDDP] (off) [ 28.731300] ACPI: Power Resource [LPTP] (off) [ 28.731327] Linux Plug and Play Support v0.97 (c) Adam Belay [ 28.731357] pnp: PnP ACPI init [ 28.731379] ACPI: bus type pnp registered [ 28.736324] pnp: PnP ACPI: found 10 devices [ 28.736331] ACPI: ACPI bus type pnp unregistered [ 28.736339] PnPBIOS: Disabled by ACPI PNP [ 28.736486] PCI: Using ACPI for IRQ routing [ 28.736493] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 28.741595] NET: Registered protocol family 8 [ 28.741599] NET: Registered protocol family 20 [ 28.741798] pnp: 00:01: iomem range 0xfee00000-0xfee00fff could not be reserved [ 28.744676] Time: tsc clocksource has been installed. [ 28.773010] PCI: Bridge: 0000:00:1e.0 [ 28.773014] IO window: disabled. [ 28.773021] MEM window: dfd00000-dfdfffff [ 28.773027] PREFETCH window: 40000000-400fffff [ 28.773045] PCI: Setting latency timer of device 0000:00:1e.0 to 64 [ 28.773072] NET: Registered protocol family 2 [ 28.812618] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 28.812895] TCP established hash table entries: 131072 (order: 8, 1572864 bytes) [ 28.815501] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 28.816398] TCP: Hash tables configured (established 131072 bind 65536) [ 28.816407] TCP reno registered [ 28.824778] checking if image is initramfs... it is [ 29.275693] Switched to high resolution mode on CPU 0 [ 29.653397] Freeing initrd memory: 7118k freed [ 29.654387] audit: initializing netlink socket (disabled) [ 29.654411] audit(1194300621.152:1): initialized [ 29.654573] highmem bounce pool size: 64 pages [ 29.661220] VFS: Disk quotas dquot_6.5.1 [ 29.661417] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 29.661707] io scheduler noop registered [ 29.661711] io scheduler anticipatory registered [ 29.661714] io scheduler deadline registered [ 29.661763] io scheduler cfq registered (default) [ 29.661787] Boot video device is 0000:00:02.0 [ 29.662299] isapnp: Scanning for PnP cards... [ 30.015953] isapnp: No Plug & Play device found [ 30.158634] Real Time Clock Driver v1.12ac [ 30.158902] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 30.159050] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 30.161437] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 30.164021] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 30.164363] input: Macintosh mouse button emulation as /class/input/input0 [ 30.164797] PNP: No PS/2 controller found. Probing ports directly. [ 30.167815] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 30.167828] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 30.168450] mice: PS/2 mouse device common for all mice [ 30.168852] EISA: Probing bus 0 at eisa.0 [ 30.168897] EISA: Detected 0 cards. [ 30.169058] TCP cubic registered [ 30.169090] NET: Registered protocol family 1 [ 30.169136] Using IPI No-Shortcut mode [ 30.169450] Magic number: 15:356:198 [ 30.169552] hash matches device ttypd [ 30.170384] Freeing unused kernel memory: 364k freed [ 31.608956] AppArmor: AppArmor initialized<5>audit(1194300623.152:2): type=1505 info="AppArmor initialized" pid=1172 [ 31.623358] fuse init (API version 7.8) [ 31.634541] Failure registering capabilities with primary security module. [ 31.659225] ACPI: Processor [CPU1] (supports 8 throttling states) [ 31.659254] ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device is not present [20070126] [ 32.939831] usbcore: registered new interface driver usbfs [ 32.939884] usbcore: registered new interface driver hub [ 32.939967] usbcore: registered new device driver usb [ 32.941487] USB Universal Host Controller Interface driver v3.0 [ 32.941602] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 32.941619] PCI: Setting latency timer of device 0000:00:1d.0 to 64 [ 32.941625] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 32.941886] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 32.941930] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000e400 [ 32.942159] usb usb1: configuration #1 chosen from 1 choice [ 32.942218] hub 1-0:1.0: USB hub found [ 32.942237] hub 1-0:1.0: 2 ports detected [ 33.044688] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 17 [ 33.044706] PCI: Setting latency timer of device 0000:00:1d.1 to 64 [ 33.044711] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 33.044766] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 [ 33.044807] uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000e800 [ 33.044989] usb usb2: configuration #1 chosen from 1 choice [ 33.045053] hub 2-0:1.0: USB hub found [ 33.045071] hub 2-0:1.0: 2 ports detected [ 33.083300] SCSI subsystem initialized [ 33.092001] libata version 2.21 loaded. [ 33.148489] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18 [ 33.148510] PCI: Setting latency timer of device 0000:00:1d.2 to 64 [ 33.148515] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 33.148581] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 [ 33.148620] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ec00 [ 33.148817] usb usb3: configuration #1 chosen from 1 choice [ 33.148873] hub 3-0:1.0: USB hub found [ 33.148890] hub 3-0:1.0: 2 ports detected [ 33.252766] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 19 [ 33.252793] PCI: Setting latency timer of device 0000:00:1d.7 to 64 [ 33.252799] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 33.252870] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4 [ 33.252931] ehci_hcd 0000:00:1d.7: debug port 1 [ 33.252941] PCI: cache line size of 128 is not supported by device 0000:00:1d.7 [ 33.252960] ehci_hcd 0000:00:1d.7: irq 19, io mem 0xdff7bc00 [ 33.256826] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 33.257004] usb usb4: configuration #1 chosen from 1 choice [ 33.257063] hub 4-0:1.0: USB hub found [ 33.257082] hub 4-0:1.0: 6 ports detected [ 33.309409] Floppy drive(s): fd0 is 1.44M [ 33.355128] FDC 0 is a post-1991 82077 [ 33.360529] ata_piix 0000:00:1f.1: version 2.11 [ 33.360562] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18 [ 33.360629] PCI: Setting latency timer of device 0000:00:1f.1 to 64 [ 33.360811] scsi0 : ata_piix [ 33.360932] scsi1 : ata_piix [ 33.361103] ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001fc00 irq 14 [ 33.361108] ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001fc08 irq 15 [ 33.523851] ata1.00: ATA-7: SAMSUNG SP1613N, VB100-50, max UDMA/100 [ 33.523857] ata1.00: 312581808 sectors, multi 16: LBA48 [ 33.555774] ata1.00: configured for UDMA/100 [ 33.875063] ata2.00: ATAPI: PIONEER DVD-RW DVR-112D, 1.21, max UDMA/66 [ 34.046732] ata2.00: configured for UDMA/66 [ 34.046951] scsi 0:0:0:0: Direct-Access ATA SAMSUNG SP1613N VB10 PQ: 0 ANSI: 5 [ 34.053974] scsi 1:0:0:0: CD-ROM PIONEER DVD-RW DVR-112D 1.21 PQ: 0 ANSI: 5 [ 34.060474] b44.c:v1.01 (Jun 16, 2006) [ 34.060502] ACPI: PCI Interrupt 0000:03:0a.0[A] -> GSI 19 (level, low) -> IRQ 17 [ 34.064524] eth0: Broadcom 4400 10/100BaseT Ethernet 00:02:e3:30:70:1c [ 34.099905] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) [ 34.102235] sd 0:0:0:0: [sda] Write Protect is off [ 34.102242] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 34.102309] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 34.102506] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) [ 34.102536] sd 0:0:0:0: [sda] Write Protect is off [ 34.102541] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 34.102578] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 34.102590] sda: sda1 sda2 sda3 sda4 [ 34.130856] sd 0:0:0:0: [sda] Attached SCSI disk [ 34.140256] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 34.140706] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 34.142333] usb 2-1: new low speed USB device using uhci_hcd and address 2 [ 34.174296] sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray [ 34.174306] Uniform CD-ROM driver Revision: 3.20 [ 34.174791] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 34.318326] usb 2-1: configuration #1 chosen from 1 choice [ 34.492082] Attempting manual resume [ 34.492087] swsusp: Resume From Partition 8:3 [ 34.492090] PM: Checking swsusp image. [ 34.492407] PM: Resume from disk failed. [ 34.543941] kjournald starting. Commit interval 5 seconds [ 34.543969] EXT3-fs: mounted filesystem with ordered data mode. [ 34.557532] usb 2-2: new low speed USB device using uhci_hcd and address 3 [ 34.732452] usb 2-2: configuration #1 chosen from 1 choice [ 34.735505] usbcore: registered new interface driver hiddev [ 34.750799] input: CHICONY HP Basic USB Keyboard as /class/input/input1 [ 34.750828] input: USB HID v1.10 Keyboard [CHICONY HP Basic USB Keyboard] on usb-0000:00:1d.1-1 [ 34.763624] input: Logitech Optical USB Mouse as /class/input/input2 [ 34.763670] input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.1-2 [ 34.763696] usbcore: registered new interface driver usbhid [ 34.763702] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 43.237163] NET: Registered protocol family 17 [ 44.229699] Linux agpgart interface v0.102 (c) Dave Jones [ 44.271056] agpgart: Detected an Intel 830M Chipset. [ 44.271182] agpgart: Detected 8060K stolen memory. [ 44.288022] agpgart: AGP aperture is 128M @ 0xd0000000 [ 44.401212] i810_smbus 0000:00:02.0: i810/i815 i2c device found. [ 44.417970] iTCO_vendor_support: vendor-support=0 [ 44.430376] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007) [ 44.430584] iTCO_wdt: Found a ICH4 TCO device (Version=1, TCOBASE=0x0860) [ 44.430693] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 44.520954] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 44.678178] b44: eth0: Link is up at 100 Mbps, full duplex. [ 44.678184] b44: eth0: Flow control is off for TX and off for RX. [ 44.919839] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 44.920603] intel_rng: FWH not detected [ 45.536819] input: PC Speaker as /class/input/input3 [ 45.718514] parport_pc 00:09: reported by Plug and Play ACPI [ 45.718574] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA] [ 46.243760] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 21 [ 46.243802] PCI: Setting latency timer of device 0000:00:1f.5 to 64 [ 46.662209] intel8x0_measure_ac97_clock: measured 54821 usecs [ 46.662215] intel8x0: clocking to 48000 [ 47.027831] lp0: using parport0 (interrupt-driven). [ 47.120500] Adding 2000084k swap on /dev/sda3. Priority:-1 extents:1 across:2000084k [ 47.378906] EXT3 FS on sda4, internal journal [ 47.910823] kjournald starting. Commit interval 5 seconds [ 47.911087] EXT3 FS on sda2, internal journal [ 47.911098] EXT3-fs: mounted filesystem with ordered data mode. [ 50.399923] No dock devices found. [ 50.517276] input: Power Button (FF) as /class/input/input4 [ 50.525589] ACPI: Power Button (FF) [PWRF] [ 50.578050] input: Power Button (CM) as /class/input/input5 [ 50.586219] ACPI: Power Button (CM) [PWRB] [ 51.258796] NET: Registered protocol family 10 [ 51.258989] lo: Disabled Privacy Extensions [ 54.529526] [drm] Initialized drm 1.1.0 20060810 [ 54.535666] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 54.539801] [drm] Initialized i915 1.6.0 20060119 on minor 0 [ 55.185682] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) [ 55.185689] apm: overridden by ACPI. [ 55.705919] Failure registering capabilities with primary security module. [ 57.867849] vmmon: module license 'unspecified' taints kernel. [ 57.873092] /dev/vmmon[5007]: VMCI: Driver initialized. [ 57.879331] /dev/vmmon[5007]: Module vmmon: registered with major=10 minor=165 [ 57.879905] /dev/vmmon[5007]: Initial HV check: anyNotCapable=1 anyUnlocked=0 anyEnabled=0 anyDisabled=0 [ 57.879917] /dev/vmmon[5007]: Module vmmon: initialized [ 59.065238] /dev/vmnet: open called by PID 5051 (vmnet-bridge) [ 59.065773] /dev/vmnet: hub 0 does not exist, allocating memory. [ 59.066221] /dev/vmnet: port on hub 0 successfully opened [ 59.066653] bridge-eth0: enabling the bridge [ 59.067048] bridge-eth0: up [ 59.067388] bridge-eth0: already up [ 59.067402] bridge-eth0: attached [ 60.291948] /dev/vmnet: open called by PID 5067 (vmnet-dhcpd) [ 60.292440] /dev/vmnet: hub 1 does not exist, allocating memory. [ 60.292929] /dev/vmnet: port on hub 1 successfully opened [ 60.823835] /dev/vmnet: open called by PID 5078 (vmnet-dhcpd) [ 60.824341] /dev/vmnet: hub 8 does not exist, allocating memory. [ 60.824783] /dev/vmnet: port on hub 8 successfully opened [ 60.857654] /dev/vmnet: open called by PID 5083 (vmnet-natd) [ 60.858175] /dev/vmnet: port on hub 8 successfully opened [ 61.450031] eth0: no IPv6 routers present [ 69.936458] /dev/vmnet: open called by PID 5166 (vmnet-netifup) [ 69.936760] /dev/vmnet: port on hub 1 successfully opened [ 70.278224] /dev/vmnet: open called by PID 5177 (vmnet-netifup) [ 70.278435] /dev/vmnet: port on hub 8 successfully opened [ 80.583053] vmnet1: no IPv6 routers present [ 81.101783] vmnet8: no IPv6 routers present [ 348.971308] UDF-fs: No VRS found [ 349.000393] ISO 9660 Extensions: Microsoft Joliet Level 3 [ 349.521887] ISOFS: changing to secondary root