IOS-e820: 0000000000100000 - 000000003bf00000 (usable)
 BIOS-e820: 000000003bf00000 - 000000003bf16000 (ACPI data)
 BIOS-e820: 000000003bf16000 - 000000003bf80000 (ACPI NVS)
 BIOS-e820: 000000003bf80000 - 0000000040000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
63MB HIGHMEM available.
896MB LOWMEM available.
On node 0 totalpages: 245504
  DMA zone: 4096 pages, LIFO batch:0
  DMA32 zone: 0 pages, LIFO batch:0
  Normal zone: 225280 pages, LIFO batch:31
  HighMem zone: 16128 pages, LIFO batch:3
DMI present.
ACPI: RSDP (v000 HP                                    ) @ 0x000f8920
ACPI: RSDT (v001 HPQOEM SLIC-MPC 0x06040000  LTP 0x00000000) @ 0x3bf0d2ce
ACPI: FADT (v001 HP     MCP51M   0x06040000 PTL_ 0x000f4240) @ 0x3bf15c36
ACPI: SSDT (v001 HP     POWERNOW 0x06040000  LTP 0x00000001) @ 0x3bf15caa
ACPI: MCFG (v001 HP       MCFG   0x06040000  LTP 0x00000000) @ 0x3bf15d9e
ACPI: HPET (v001 PTLTD  HPETTBL  0x06040000  LTP 0x00000001) @ 0x3bf15dda
ACPI: MADT (v001 HP     	 APIC   0x06040000  LTP 0x00000000) @ 0x3bf15e12
ACPI: BOOT (v001     HP $SBFTBL$ 0x06040000  LTP 0x00000001) @ 0x3bf15e62
ACPI: SLIC (v001 HPQOEM SLIC-MPC 0x06040000  LTP 0x00000001) @ 0x3bf15e8a
ACPI: DSDT (v001 HP       MCP51M 0x06040000 MSFT 0x03000000) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: HPET id: 0x10de8201 base: 0xfed00000
Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
Built 1 zonelists
Kernel command line: vga=769 changes=slaxsave.dat max_loop=255 initrd=boot/initrd.gz init=linuxrc load_ramdisk=1 prompt_ramdisk=0 ramdisk_size=4444 root=/dev/ram0 rw BOOT_IMAGE=boot/vmlinuz 
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Console: colour dummy device 80x25
spurious 8259A interrupt: IRQ7.
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 965336k/982016k available (4166k kernel code, 16084k reserved, 1287k data, 488k init, 64512k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Using HPET for base-timer
Using HPET for gettimeofday
Detected 1808.338 MHz processor.
Using hpet for high-res timesource
Calibrating delay using timer specific routine.. 3620.93 BogoMIPS (lpj=7241861)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 078bfbff ebd3fbff 00000000 00000000 00002001 00000000 00000019
CPU: After vendor identify, caps: 078bfbff ebd3fbff 00000000 00000000 00002001 00000000 00000019
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 078bfbff ebd3fbff 00000000 00000410 00002001 00000000 00000019
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Mobile AMD Sempron(tm) Processor 3500+ stepping 02
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0ca0)
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 1315k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS BUG #81[000fdcf0] found
PCI: Using MMCONFIG
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:00:05.0
PCI: Transparent bridge - 0000:00:10.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC0] (gpe 16) interrupt mode.
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR2._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LK1E] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LK2E] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LK3E] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LK4E] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LUS0] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LUS2] (IRQs 5 *7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LPID] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LTID] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LSI1] (IRQs 5 7 9 *10 11 14 15), disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Bridge: 0000:00:02.0
  IO window: 4000-4fff
  MEM window: b4000000-b7ffffff
  PREFETCH window: d0000000-d01fffff
PCI: Bridge: 0000:00:03.0
  IO window: disabled.
  MEM window: b8000000-bbffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:10.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:02.0 to 64
PCI: Setting latency timer of device 0000:00:03.0 to 64
PCI: Setting latency timer of device 0000:00:10.0 to 64
Simple Boot Flag at 0x36 set to 0x1
apm: BIOS not found.
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NTFS driver 2.1.26 [Flags: R/O].
JFS: nTxBlock = 7553, nTxLock = 60428
SGI XFS with ACLs, security attributes, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:02.0 to 64
pcie_portdrv_probe->Dev[02fc:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0:pcie00]
Allocate Port Service[0000:00:02.0:pcie03]
PCI: Setting latency timer of device 0000:00:03.0 to 64
pcie_portdrv_probe->Dev[02fd:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:03.0:pcie00]
Allocate Port Service[0000:00:03.0:pcie03]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
vesafb: framebuffer at 0xc0000000, mapped to 0xf8c80000, using 600k, total 65536k
vesafb: mode is 640x480x8, linelength=640, pages=10
vesafb: protected mode interface info at c000:d750
vesafb: scrolling: redraw
vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0
Console: switching to colour frame buffer device 80x30
fb0: VESA VGA frame buffer device
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Lid Switch [LID]
ACPI: Video Device [UVGA] (multi-head: yes  rom: no  post: no)
ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Thermal Zone [THRM] (57 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 4444K size 1024 blocksize
loop: loaded (max 255 devices)
Compaq SMART2 Driver (v 2.6.0)
HP CISS Driver (v 2.6.10)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-MCP51: IDE controller at PCI slot 0000:00:0d.0
NFORCE-MCP51: chipset revision 241
NFORCE-MCP51: not 100% native mode: will probe irqs later
NFORCE-MCP51: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE-MCP51: 0000:00:0d.0 (rev f1) UDMA133 controller
    ide0: BM-DMA at 0x3080-0x3087, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
hda: TSSTcorp CDDVDW TS-L632H, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: ATAPI 16X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
Adaptec aacraid driver (1.1-4 May  4 2006 18:40:51)
scsi: <fdomain> Detection failed (no card)
sym53c416.c: Version 1.0.0-ac
qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= optionsEmulex LightPulse Fibre Channel SCSI driver 8.1.1
Copyright(c) 2004-2005 Emulex.  All rights reserved.
Failed initialization of WD-7000 SCSI card!
megaraid cmm: 2.20.2.6 (Release Date: Mon Mar 7 00:01:03 EST 2005)
megaraid: 2.20.4.7 (Release Date: Mon Nov 14 12:27:22 EST 2005)
megasas: 00.00.02.04 Fri Feb 03 14:31:44 PST 2006
GDT-HA: Storage RAID Controller Driver. Version: 3.04 
GDT-HA: Found 0 PCI Storage RAID Controllers
3ware Storage Controller device driver for Linux v1.26.02.001.
3ware 9000 Storage Controller device driver for Linux v2.26.02.007.
nsp32: loading...
ipr: IBM Power RAID SCSI Device Driver version: 2.1.2 (February 8, 2006)
libata version 1.20 loaded.
sata_nv 0000:00:0e.0: version 0.8
PCI: Enabling device 0000:00:0e.0 (0005 -> 0007)
ACPI: PCI Interrupt Link [LTID] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [LTID] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:0e.0 to 64
ata1: SATA max UDMA/133 cmd 0x30C0 ctl 0x30B6 bmdma 0x3090 irq 5
ata2: SATA max UDMA/133 cmd 0x30B8 ctl 0x30B2 bmdma 0x3098 irq 5
ata1: SATA link up 1.5 Gbps (SStatus 113)
ata1: dev 0 cfg 49:2f00 82:706b 83:7c09 84:6123 85:7069 86:bc09 87:6123 88:203f
ata1: dev 0 ATA-7, max UDMA/100, 234441648 sectors: LBA48
ata1: dev 0 configured for UDMA/100
scsi2 : sata_nv
ata2: SATA link down (SStatus 0)
scsi3 : sata_nv
  Vendor: ATA       Model: WDC WD1200BEVS-6  Rev: 04.0
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
 sda: sda1 sda2
sd 2:0:0:0: Attached scsi disk sda
I2O subsystem v1.325
i2o: max drivers = 8
I2O Configuration OSM v1.323
I2O Bus Adapter OSM v1.317
I2O Block Device OSM v1.325
I2O SCSI Peripheral OSM v1.316
I2O ProcFS OSM v1.316
Fusion MPT base driver 3.03.07
Copyright (c) 1999-2005 LSI Logic Corporation
Fusion MPT SPI Host driver 3.03.07
Fusion MPT FC Host driver 3.03.07
Fusion MPT SAS Host driver 3.03.07
usbmon: debugfs is not available
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard as /class/input/input0
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI wakeup devices: 
USB0 MAC0 
ACPI: (supports S0 S3 S4 S5)
RAMDISK: Compressed image found at block 0
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 488k freed
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering unionfs 20060423-1600
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
UDF-fs: No partition found (1)
XFS: bad magic number
XFS: SB validate failed
NTFS volume version 3.1.
NTFS volume version 3.1.
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
Linux agpgart interface v0.101 (c) Dave Jones
input: ImPS/2 Synaptics TouchPad as /class/input/input1
fuse init (API version 7.6)
NTFS volume version 3.1.
NTFS volume version 3.1.
Intel ISA PCIC probe: not found.
Databook TCIC-2 PCMCIA probe: not found.
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.49.
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LMAC] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:14.0 to 64
eth0: forcedeth.c: subsystem: 0103c:30b7 bound to 0000:00:14.0
ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LAZA] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:10.1 to 64
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [LUS2] -> GSI 7 (level, low) -> IRQ 7
PCI: Setting latency timer of device 0000:00:0b.1 to 64
ehci_hcd 0000:00:0b.1: EHCI Host Controller
ehci_hcd 0000:00:0b.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:0b.1
ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0b.1: irq 7, io mem 0xb0005000
ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LUS0] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:0b.0 to 64
ohci_hcd 0000:00:0b.0: OHCI Host Controller
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0b.0: irq 11, io mem 0xb0004000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 8 ports detected
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
USB Universal Host Controller Interface driver v2.3
eth0: no link during initialization.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
hda-intel: Invalid position buffer, using LPIB read method instead.