[ 0.000000] Linux version 2.6.22-12-generic (buildd@vernadsky) (gcc version 4.1.3 20070831 (prerelease) (Ubuntu 4.1.2-16ubuntu1)) #1 SMP Sun Sep 23 18:11:30 GMT 2007 (Ubuntu 2.6.22-12.39-generic) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003fff0000 (usable) [ 0.000000] BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data) [ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) [ 0.000000] 127MB HIGHMEM available. [ 0.000000] 896MB LOWMEM available. [ 0.000000] Entering add_active_range(0, 0, 262128) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] HighMem 229376 -> 262128 [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 262128 [ 0.000000] On node 0 totalpages: 262128 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1760 pages used for memmap [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 [ 0.000000] HighMem zone: 255 pages used for memmap [ 0.000000] HighMem zone: 32497 pages, LIFO batch:7 [ 0.000000] DMI 2.2 present. [ 0.000000] ACPI: RSDP 000F6DB0, 0014 (r0 VIA694) [ 0.000000] ACPI: RSDT 3FFF3000, 0028 (r1 VIA694 AWRDACPI 42302E31 AWRD 0) [ 0.000000] ACPI: FACP 3FFF3040, 0074 (r1 VIA694 AWRDACPI 42302E31 AWRD 0) [ 0.000000] ACPI: DSDT 3FFF30C0, 2578 (r1 VIA694 AWRDACPI 1000 MSFT 100000C) [ 0.000000] ACPI: FACS 3FFF0000, 0040 [ 0.000000] ACPI: PM-Timer IO Port: 0x4008 [ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:bfff0000) [ 0.000000] Built 1 zonelists. Total pages: 260081 [ 0.000000] Kernel command line: BOOT_IMAGE=/casper/vmlinuz file=/cdrom/preseed/kubuntu.seed boot=casper initrd=/casper/initrd.gz quiet splash -- console-setup/layoutcode=pt [ 0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic" [ 0.000000] mapped APIC to ffffd000 (0180f000) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Detected 1466.356 MHz processor. [ 32.817644] Console: colour VGA+ 80x25 [ 32.819329] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 32.822205] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 32.873037] Memory: 1027624k/1048512k available (2017k kernel code, 20196k reserved, 918k data, 364k init, 131008k highmem) [ 32.873053] virtual kernel memory layout: [ 32.873054] fixmap : 0xfff4d000 - 0xfffff000 ( 712 kB) [ 32.873056] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 32.873058] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) [ 32.873060] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 32.873061] .init : 0xc03e3000 - 0xc043e000 ( 364 kB) [ 32.873063] .data : 0xc02f8456 - 0xc03ddea4 ( 918 kB) [ 32.873065] .text : 0xc0100000 - 0xc02f8456 (2017 kB) [ 32.873069] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 32.873153] SLUB: Genslabs=22, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1 [ 32.953149] Calibrating delay using timer specific routine.. 2935.48 BogoMIPS (lpj=5870966) [ 32.953225] Security Framework v1.0.0 initialized [ 32.953244] SELinux: Disabled at boot. [ 32.953274] Mount-cache hash table entries: 512 [ 32.953597] CPU: After generic identify, caps: 0383f9ff c1cbf9ff 00000000 00000000 00000000 00000000 00000000 [ 32.953613] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 32.953617] CPU: L2 Cache: 256K (64 bytes/line) [ 32.953622] CPU: After all inits, caps: 0383f9ff c1cbf9ff 00000000 00000420 00000000 00000000 00000000 [ 32.953648] Compat vDSO mapped to ffffe000. [ 32.953675] Checking 'hlt' instruction... OK. [ 32.969441] SMP alternatives: switching to UP code [ 32.970003] Freeing SMP alternatives: 11k freed [ 32.970614] Early unpacking initramfs... done [ 33.433618] ACPI: Core revision 20070126 [ 33.433793] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found. [ 33.435070] ACPI: setting ELCR to 0800 (from 0e20) [ 33.436389] CPU0: AMD Athlon(tm) XP 1700+ stepping 02 [ 33.436399] SMP motherboard not detected. [ 33.436403] Local APIC not detected. Using dummy APIC emulation. [ 33.436489] Brought up 1 CPUs [ 33.436769] Booting paravirtualized kernel on bare hardware [ 33.436888] Time: 22:00:54 Date: 09/05/107 [ 33.436959] NET: Registered protocol family 16 [ 33.437137] EISA bus registered [ 33.437158] ACPI: bus type pci registered [ 33.468403] PCI: PCI BIOS revision 2.10 entry at 0xfb380, last bus=2 [ 33.468407] PCI: Using configuration type 1 [ 33.468410] Setting up standard PCI resources [ 33.475234] ACPI: EC: Look up EC in DSDT [ 33.478129] ACPI: Interpreter enabled [ 33.478134] ACPI: (supports S0 S1 S4 S5) [ 33.478155] ACPI: Using PIC for interrupt routing [ 33.482857] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 33.482875] PCI: Probing PCI hardware (bus 00) [ 33.483207] PCI quirk: region 6000-607f claimed by vt82c686 HW-mon [ 33.483211] PCI quirk: region 5000-500f claimed by vt82c686 SMB [ 33.483861] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 33.500031] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15) [ 33.500196] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *10 11 12 14 15) [ 33.500360] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 *5 6 7 10 11 12 14 15) [ 33.500521] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *9 [ 33.500632] Linux Plug and Play Support v0.97 (c) Adam Belay [ 33.500661] pnp: PnP ACPI init [ 33.500678] ACPI: bus type pnp registered [ 33.503763] pnp: PnP ACPI: found 13 devices [ 33.503767] ACPI: ACPI bus type pnp unregistered [ 33.503775] PnPBIOS: Disabled by ACPI PNP [ 33.503874] PCI: Using ACPI for IRQ routing [ 33.503878] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 33.561141] NET: Registered protocol family 8 [ 33.561144] NET: Registered protocol family 20 [ 33.561265] pnp: 00:00: iomem range 0xcf600-0xcffff has been reserved [ 33.561269] pnp: 00:00: iomem range 0xf0000-0xf7fff could not be reserved [ 33.561274] pnp: 00:00: iomem range 0xf8000-0xfbfff could not be reserved [ 33.561278] pnp: 00:00: iomem range 0xfc000-0xfffff could not be reserved [ 33.564852] Time: tsc clocksource has been installed. [ 33.591759] PCI: Bridge: 0000:00:01.0 [ 33.591762] IO window: disabled. [ 33.591768] MEM window: e4000000-e5ffffff [ 33.591772] PREFETCH window: d0000000-dfffffff [ 33.591777] PCI: Bridge: 0000:00:14.0 [ 33.591779] IO window: disabled. [ 33.591784] MEM window: e7000000-e70fffff [ 33.591788] PREFETCH window: disabled. [ 33.591808] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 33.591836] NET: Registered protocol family 2 [ 33.628934] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 33.629327] TCP established hash table entries: 131072 (order: 8, 1572864 bytes) [ 33.634967] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 33.636722] TCP: Hash tables configured (established 131072 bind 65536) [ 33.636730] TCP reno registered [ 33.645129] checking if image is initramfs... it is [ 34.092649] Switched to high resolution mode on CPU 0 [ 34.515482] Freeing initrd memory: 7323k freed [ 34.516226] audit: initializing netlink socket (disabled) [ 34.516256] audit(1191621654.196:1): initialized [ 34.516415] highmem bounce pool size: 64 pages [ 34.519195] VFS: Disk quotas dquot_6.5.1 [ 34.519287] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 34.519461] io scheduler noop registered [ 34.519464] io scheduler anticipatory registered [ 34.519467] io scheduler deadline registered [ 34.519486] io scheduler cfq registered (default) [ 34.519519] Applying VIA southbridge workaround. [ 34.519524] PCI: VIA PCI bridge detected. Disabling DAC. [ 34.519529] PCI: Disabling Via external APIC routing [ 34.519567] Boot video device is 0000:01:00.0 [ 34.519976] isapnp: Scanning for PnP cards... [ 34.873947] isapnp: No Plug & Play device found [ 34.919238] Real Time Clock Driver v1.12ac [ 34.919391] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 34.919544] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 34.919991] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 34.921305] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 34.921887] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 34.923144] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 34.923533] input: Macintosh mouse button emulation as /class/input/input0 [ 34.923665] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 34.924079] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 34.924087] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 34.924436] mice: PS/2 mouse device common for all mice [ 34.924625] EISA: Probing bus 0 at eisa.0 [ 34.924654] Cannot allocate resource for EISA slot 4 [ 34.924658] Cannot allocate resource for EISA slot 5 [ 34.924661] Cannot allocate resource for EISA slot 6 [ 34.924673] EISA: Detected 0 cards. [ 34.925017] TCP cubic registered [ 34.925033] NET: Registered protocol family 1 [ 34.925070] Using IPI No-Shortcut mode [ 34.925386] Magic number: 11:694:46 [ 34.925397] hash matches device ttyef [ 34.926531] Freeing unused kernel memory: 364k freed [ 34.964290] input: AT Translated Set 2 keyboard as /class/input/input1 [ 36.255821] AppArmor: AppArmor initialized<5>audit(1191621656.196:2): type=1505 info="AppArmor initialized" pid=1170 [ 36.269069] fuse init (API version 7.8) [ 36.278339] Failure registering capabilities with primary security module. [ 36.298671] ACPI: CPU0 (power states: C1[C1] C2[C2]) [ 36.298682] ACPI: Processor [CPU0] (supports 2 throttling states) [ 37.295678] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 37.295691] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 37.296830] VP_IDE: IDE controller at PCI slot 0000:00:07.1 [ 37.296861] VP_IDE: chipset revision 6 [ 37.296864] VP_IDE: not 100% native mode: will probe irqs later [ 37.296879] VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1 [ 37.296890] ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:pio [ 37.296908] ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:pio [ 37.296920] Probing IDE interface ide0... [ 37.316217] usbcore: registered new interface driver usbfs [ 37.316268] usbcore: registered new interface driver hub [ 37.316306] usbcore: registered new device driver usb [ 37.317774] USB Universal Host Controller Interface driver v3.0 [ 37.416039] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004) [ 37.546363] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver [ 37.696825] FDC 0 is a post-1991 82077 [ 37.726905] hda: ST340016A, ATA DISK drive [ 4.984000] Marking TSC unstable due to: possible TSC halt in C2. [ 5.012000] Time: acpi_pm clocksource has been installed. [ 5.532000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 5.532000] Probing IDE interface ide1... [ 6.396000] hdc: HL-DT-ST DVDRAM GSA-4160B, ATAPI CD/DVD-ROM drive [ 6.732000] ide1 at 0x170-0x177,0x376 on irq 15 [ 6.744000] SCSI subsystem initialized [ 6.756000] libata version 2.21 loaded. [ 6.760000] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10 [ 6.760000] PCI: setting IRQ 10 as level-triggered [ 6.760000] ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10 [ 6.760000] PCI: VIA VLink IRQ fixup for 0000:00:07.2, from 9 to 10 [ 6.760000] uhci_hcd 0000:00:07.2: UHCI Host Controller [ 6.760000] uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1 [ 6.760000] uhci_hcd 0000:00:07.2: irq 10, io base 0x0000d400 [ 6.760000] usb usb1: configuration #1 chosen from 1 choice [ 6.760000] hub 1-0:1.0: USB hub found [ 6.760000] hub 1-0:1.0: 2 ports detected [ 6.772000] hda: max request size: 128KiB [ 6.788000] hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100) [ 6.788000] hda: cache flushes not supported [ 6.788000] hda: hda1 hda2 hda3 [ 6.860000] hdc: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(66) [ 6.860000] Uniform CD-ROM driver Revision: 3.20 [ 6.864000] ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10 [ 6.864000] PCI: VIA VLink IRQ fixup for 0000:00:07.3, from 9 to 10 [ 6.864000] uhci_hcd 0000:00:07.3: UHCI Host Controller [ 6.864000] uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2 [ 6.864000] uhci_hcd 0000:00:07.3: irq 10, io base 0x0000d800 [ 6.864000] usb usb2: configuration #1 chosen from 1 choice [ 6.864000] hub 2-0:1.0: USB hub found [ 6.864000] hub 2-0:1.0: 2 ports detected [ 6.968000] 8139cp 0000:00:11.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip [ 6.968000] 8139cp 0000:00:11.0: Try the "8139too" driver instead. [ 6.968000] 8139too Fast Ethernet driver 0.9.28 [ 6.968000] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 [ 6.968000] PCI: setting IRQ 11 as level-triggered [ 6.968000] ACPI: PCI Interrupt 0000:00:11.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 [ 6.972000] eth0: RealTek RTL8139 at 0xf8838000, 00:80:5a:23:43:b0, IRQ 11 [ 6.972000] eth0: Identified 8139 chip type 'RTL-8100B/8139D' [ 6.972000] ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10 [ 6.972000] ohci_hcd 0000:02:08.0: OHCI Host Controller [ 6.972000] ohci_hcd 0000:02:08.0: new USB bus registered, assigned bus number 3 [ 6.972000] ohci_hcd 0000:02:08.0: irq 10, io mem 0xe7007000 [ 7.536000] usb usb3: configuration #1 chosen from 1 choice [ 7.536000] hub 3-0:1.0: USB hub found [ 7.536000] hub 3-0:1.0: 3 ports detected [ 7.780000] kjournald starting. Commit interval 5 seconds [ 7.780000] EXT3-fs: mounted filesystem with ordered data mode. [ 7.808000] kjournald starting. Commit interval 5 seconds [ 7.808000] EXT3-fs: mounted filesystem with ordered data mode. [ 8.052000] ACPI: PCI Interrupt 0000:02:08.1[B] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 [ 8.052000] ohci_hcd 0000:02:08.1: OHCI Host Controller [ 8.052000] ohci_hcd 0000:02:08.1: new USB bus registered, assigned bus number 4 [ 8.052000] ohci_hcd 0000:02:08.1: irq 11, io mem 0xe7004000 [ 8.612000] usb usb4: configuration #1 chosen from 1 choice [ 8.616000] hub 4-0:1.0: USB hub found [ 8.616000] hub 4-0:1.0: 2 ports detected [ 8.860000] ISO 9660 Extensions: Microsoft Joliet Level 3 [ 8.924000] ISO 9660 Extensions: RRIP_1991A [ 8.988000] Registering unionfs 2.1.4 (for 2.6.22.6) [ 9.008000] loop: module loaded [ 9.132000] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10 [ 9.132000] ACPI: PCI Interrupt 0000:02:08.2[C] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 [ 9.132000] ehci_hcd 0000:02:08.2: EHCI Host Controller [ 9.132000] ehci_hcd 0000:02:08.2: new USB bus registered, assigned bus number 5 [ 9.156000] ehci_hcd 0000:02:08.2: irq 10, io mem 0xe7005000 [ 9.156000] ehci_hcd 0000:02:08.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004 [ 9.156000] usb usb5: configuration #1 chosen from 1 choice [ 9.156000] hub 5-0:1.0: USB hub found [ 9.156000] hub 5-0:1.0: 5 ports detected [ 9.260000] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5 [ 9.260000] PCI: setting IRQ 5 as level-triggered [ 9.260000] ACPI: PCI Interrupt 0000:02:0b.0[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 [ 9.312000] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[5] MMIO=[e7006000-e70067ff] Max Packet=[2048] IR/IT contexts=[4/8] [ 9.440000] squashfs: version 3.2-UBUNTU (2007/07/26) Phillip Lougher [ 9.548000] usb 5-4: new high speed USB device using ehci_hcd and address 2 [ 9.680000] usb 5-4: configuration #1 chosen from 1 choice [ 10.588000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[005042b5000148ab] [ 24.340000] unionfs: error creating directory tree for rename, bindex = 1, err = -30 [ 28.944000] unionfs: new lower inode mtime (bindex=0, name=log) [ 57.916000] unionfs: error creating directory tree for rename, bindex = 1, err = -30 [ 58.112000] unionfs: error creating directory tree for rename, bindex = 1, err = -30 [ 58.116000] __open_dir: branch 0 lower_mnt_idx NULL! Set to dfe9d000 [ 58.116000] __open_dir: opened f79eed48, rcS.d [ 58.116000] __open_dir: branches bstart 0, bend 1 [ 58.116000] __open_dir: 0: lower_dentry f79ee908, rcS.d, mntpoint dfe9d000 [ 58.116000] __open_dir: 1: lower_dentry f79ee908, rcS.d, mntpoint dff68300 [ 67.800000] unionfs: error creating directory tree for rename, bindex = 1, err = -30 [ 67.816000] __open_dir: branch 0 lower_mnt_idx NULL! Set to dfe9d000 [ 67.816000] __open_dir: opened c19c12a8, rc0.d [ 67.816000] __open_dir: branches bstart 0, bend 1 [ 67.816000] __open_dir: 0: lower_dentry f764cd48, rc0.d, mntpoint dfe9d000 [ 67.816000] __open_dir: 1: lower_dentry f764cd48, rc0.d, mntpoint dff68300 [ 67.816000] __open_dir: branch 0 lower_mnt_idx NULL! Set to dfe9d000 [ 67.816000] __open_dir: opened f7552b28, rc6.d [ 67.816000] __open_dir: branches bstart 0, bend 1 [ 67.816000] __open_dir: 0: lower_dentry f7552198, rc6.d, mntpoint dfe9d000 [ 67.816000] __open_dir: 1: lower_dentry f7552198, rc6.d, mntpoint dff68300 [ 68.088000] unionfs: new lower inode mtime (bindex=0, name=log) [ 81.672000] unionfs: new lower inode mtime (bindex=0, name=input) [ 84.064000] Linux agpgart interface v0.102 (c) Dave Jones [ 84.208000] agpgart: Detected VIA Twister-K/KT133x/KM133 chipset [ 84.212000] agpgart: AGP aperture is 64M @ 0xe0000000 [ 84.316000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 84.364000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 84.456000] parport_pc: VIA 686A/8231 detected [ 84.456000] parport_pc: probing current configuration [ 84.456000] parport_pc: Current parallel port base: 0x378 [ 84.456000] parport0: PC-style at 0x378, irq 7 [PCSPP,EPP] [ 84.848000] parport_pc: VIA parallel port: io=0x378, irq=7 [ 85.936000] unionfs: new lower inode mtime (bindex=0, name=i2c) [ 86.236000] unionfs: new lower inode mtime (bindex=0, name=video) [ 86.308000] Linux video capture interface: v2.00 [ 86.628000] bttv: driver version 0.9.17 loaded [ 86.628000] bttv: using 8 buffers with 2080k (520 pages) each for capture [ 86.628000] bttv: Bt8xx card found (0). [ 86.628000] ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 [ 86.628000] bttv0: Bt878 (rev 17) at 0000:00:12.0, irq: 10, latency: 32, mmio: 0xe7100000 [ 86.628000] bttv0: detected: Pinnacle PCTV [card=39], PCI subsystem ID is 11bd:0012 [ 86.628000] bttv0: using: Pinnacle PCTV Studio/Rave [card=39,autodetected] [ 86.628000] bttv0: gpio: en=00000000, out=00000000 in=00ff67ff [init] [ 86.628000] bttv0: i2c: checking for MSP34xx @ 0x80... not found [ 86.640000] bttv0: miro: id=25 tuner=1 radio=no stereo=no [ 86.640000] bttv0: using tuner=1 [ 86.640000] bttv0: i2c: checking for MSP34xx @ 0x80... not found [ 86.644000] bttv0: i2c: checking for TDA9875 @ 0xb0... not found [ 86.644000] bttv0: i2c: checking for TDA7432 @ 0x8a... not found [ 86.644000] bttv0: i2c: checking for TDA9887 @ 0x86... not found [ 87.012000] input: PC Speaker as /class/input/input2 [ 87.040000] unionfs: new lower inode mtime (bindex=0, name=mouse) [ 87.176000] input: GenPS/2 Genius Mouse as /class/input/input3 [ 87.376000] tuner 1-0060: All bytes are equal. It is not a TEA5767 [ 87.376000] tuner 1-0060: chip found @ 0xc0 (bt878 #0 [sw]) [ 87.376000] tuner 1-0060: type set to 1 (Philips PAL_I (FI1246 and compatibles)) [ 87.376000] tuner 1-0060: type set to 1 (Philips PAL_I (FI1246 and compatibles)) [ 87.384000] bttv0: registered device video0 [ 87.384000] bttv0: registered device vbi0 [ 87.384000] bttv0: PLL: 28636363 => 35468950 .. ok [ 87.556000] unionfs: new lower inode mtime (bindex=0, name=host) [ 87.720000] bt878: AUDIO driver version 0.0.0 loaded [ 87.720000] bt878: Bt878 AUDIO function found (0). [ 87.720000] ACPI: PCI Interrupt 0000:00:12.1[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 [ 87.720000] bt878_probe: card id=[0x1211bd], Unknown card. [ 87.720000] Exiting.. [ 87.720000] ACPI: PCI interrupt for device 0000:00:12.1 disabled [ 87.720000] bt878: probe of 0000:00:12.1 failed with error -22 [ 89.108000] ieee80211_crypt: registered algorithm 'NULL' [ 89.156000] ieee80211: 802.11 data/management/control stack, git-1.1.13 [ 89.156000] ieee80211: Copyright (C) 2004-2005 Intel Corporation [ 89.304000] usb 5-4: reset high speed USB device using ehci_hcd and address 2 [ 89.356000] ACPI: PCI Interrupt 0000:00:07.5[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 [ 89.356000] PCI: Setting latency timer of device 0000:00:07.5 to 64 [ 89.668000] zd1211rw 5-4:1.0: firmware version 4605 [ 89.708000] zd1211rw 5-4:1.0: zd1211 chip 0ace:1211 v4330 high 00-0e-2e AL2230_RF pa0 ----- [ 89.712000] zd1211rw 5-4:1.0: eth1 [ 89.712000] usbcore: registered new interface driver zd1211rw [ 92.252000] Adding 987988k swap on /dev/hda3. Priority:-1 extents:1 across:987988k