[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.24-21-generic (buildd@crested) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Mon Aug 25 16:57:51 UTC 2008 (Ubuntu 2.6.24-21.42-generic) [ 0.000000] Command line: root=UUID=62d3ac18-1f19-41b1-aaeb-49a2e7411e66 ro quiet splash acpi=irqpoll [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009dc00 (usable) [ 0.000000] BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000ce000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 0000000077e70000 (usable) [ 0.000000] BIOS-e820: 0000000077e70000 - 0000000077e80000 (ACPI data) [ 0.000000] BIOS-e820: 0000000077e80000 - 0000000077f00000 (ACPI NVS) [ 0.000000] BIOS-e820: 0000000077f00000 - 0000000080000000 (reserved) [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) [ 0.000000] Malformed early option 'acpi' [ 0.000000] Entering add_active_range(0, 0, 157) 0 entries of 3200 used [ 0.000000] Entering add_active_range(0, 256, 491120) 1 entries of 3200 used [ 0.000000] end_pfn_map = 1048576 [ 0.000000] DMI present. [ 0.000000] ACPI: RSDP signature @ 0xFFFF8100000F8500 checksum 0 [ 0.000000] ACPI: RSDP 000F8500, 0014 (r0 PTLTD ) [ 0.000000] ACPI: RSDT 77E7962F, 003C (r1 DELL M08 6040000 LTP 0) [ 0.000000] ACPI: FACP 77E7FC4D, 0074 (r1 ATI Bowfin 6040000 ATI F4240) [ 0.000000] ACPI: DSDT 77E7966B, 65E2 (r1 ATI SB600 6040000 MSFT 3000000) [ 0.000000] ACPI: FACS 77E90FC0, 0040 [ 0.000000] ACPI: TCPA 77E7FCC1, 0032 (r2 AMD 6040000 PTEC 0) [ 0.000000] ACPI: SSDT 77E7FCF3, 0115 (r1 PTLTD POWERNOW 6040000 LTP 1) [ 0.000000] ACPI: APIC 77E7FE08, 0046 (r1 PTLTD APIC 6040000 LTP 0) [ 0.000000] ACPI: MCFG 77E7FE4E, 003C (r1 PTLTD MCFG 6040000 LTP 0) [ 0.000000] ACPI: SLIC 77E7FE8A, 0176 (r1 DELL M08 6040000 LTP 0) [ 0.000000] ACPI: DMI detected: Dell [ 0.000000] Scanning NUMA topology in Northbridge 24 [ 0.000000] CPU has 1 num_cores [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at 0000000000000000-0000000077e70000 [ 0.000000] Entering add_active_range(0, 0, 157) 0 entries of 3200 used [ 0.000000] Entering add_active_range(0, 256, 491120) 1 entries of 3200 used [ 0.000000] Bootmem setup node 0 0000000000000000-0000000077e70000 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] DMA32 4096 -> 1048576 [ 0.000000] Normal 1048576 -> 1048576 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0 -> 157 [ 0.000000] 0: 256 -> 491120 [ 0.000000] On node 0 totalpages: 491021 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 1221 pages reserved [ 0.000000] DMA zone: 2720 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 6658 pages used for memmap [ 0.000000] DMA32 zone: 480366 pages, LIFO batch:31 [ 0.000000] Normal zone: 0 pages used for memmap [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] ATI board detected. Disabling timer routing over 8254. [ 0.000000] ACPI: PM-Timer IO Port: 0x8008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] Processor #0 (Bootup-CPU) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Setting APIC routing to flat [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] swsusp: Registered nosave memory region: 000000000009d000 - 000000000009e000 [ 0.000000] swsusp: Registered nosave memory region: 000000000009e000 - 00000000000a0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000ce000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000ce000 - 0000000000100000 [ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:60000000) [ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs [ 0.000000] PERCPU: Allocating 34656 bytes of per cpu data [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 483086 [ 0.000000] Policy zone: DMA32 [ 0.000000] Kernel command line: root=UUID=62d3ac18-1f19-41b1-aaeb-49a2e7411e66 ro quiet splash acpi=irqpoll [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 0.000000] TSC calibrated against PM_TIMER [ 18.807152] time.c: Detected 1995.003 MHz processor. [ 18.807955] Console: colour VGA+ 80x25 [ 18.807959] console [tty0] enabled [ 18.807974] Checking aperture... [ 18.807977] CPU 0: aperture @ df7e000000 size 32 MB [ 18.807979] Aperture too small (32 MB) [ 18.818491] No AGP bridge found [ 18.834662] Memory: 1924620k/1964480k available (2490k kernel code, 39464k reserved, 1318k data, 320k init) [ 18.834700] SLUB: Genslabs=12, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1 [ 18.913087] Calibrating delay using timer specific routine.. 3993.69 BogoMIPS (lpj=7987390) [ 18.913121] Security Framework initialized [ 18.913127] SELinux: Disabled at boot. [ 18.913140] AppArmor: AppArmor initialized [ 18.913144] Failure registering capabilities with primary security module. [ 18.913300] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 18.914430] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 18.914964] Mount-cache hash table entries: 256 [ 18.915093] Initializing cgroup subsys ns [ 18.915096] Initializing cgroup subsys cpuacct [ 18.915109] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 18.915111] CPU: L2 Cache: 512K (64 bytes/line) [ 18.915114] CPU 0/0 -> Node 0 [ 18.915137] SMP alternatives: switching to UP code [ 18.915660] Freeing SMP alternatives: 24k freed [ 18.915956] Early unpacking initramfs... done [ 19.221685] ACPI: Core revision 20070126 [ 19.221744] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found. [ 20.302629] ..MP-BIOS bug: 8254 timer not connected to IO-APIC [ 20.342687] Using local APIC timer interrupts. [ 20.392787] APIC timer calibration result 12468764 [ 20.392789] Detected 12.468 MHz APIC timer. [ 20.392838] Brought up 1 CPUs [ 20.392902] CPU0 attaching sched-domain: [ 20.392904] domain 0: span 01 [ 20.392906] groups: 01 [ 20.393051] net_namespace: 120 bytes [ 20.393429] Time: 2:43:40 Date: 09/30/08 [ 20.393458] NET: Registered protocol family 16 [ 20.393630] ACPI: bus type pci registered [ 20.393694] PCI: Using configuration type 1 [ 20.394603] ACPI: EC: Look up EC in DSDT [ 20.396624] ACPI: BIOS _OSI(Linux) query ignored via DMI [ 20.396885] ACPI: Interpreter enabled [ 20.396888] ACPI: (supports S0 S3 S4 S5) [ 20.396898] ACPI: Using IOAPIC for interrupt routing [ 20.397738] ACPI: EC: non-query interrupt received, switching to interrupt mode [ 20.410439] ACPI: EC: GPE = 0x14, I/O: command/status = 0x66, data = 0x62 [ 20.410442] ACPI: EC: driver started in interrupt mode [ 20.410480] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 20.410681] pci 0000:00:12.0: set SATA to AHCI mode [ 20.411948] PCI: Transparent bridge - 0000:00:14.4 [ 20.411976] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 20.412158] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB5_._PRT] [ 20.412269] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB6_._PRT] [ 20.412394] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT] [ 20.412494] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] [ 20.415450] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled. [ 20.415562] ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled. [ 20.415671] ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled. [ 20.415779] ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled. [ 20.415887] ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled. [ 20.415996] ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled. [ 20.416104] ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled. [ 20.416213] ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled. [ 20.416322] ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 7) *0, disabled. [ 20.416428] Linux Plug and Play Support v0.97 (c) Adam Belay [ 20.416456] pnp: PnP ACPI init [ 20.416462] ACPI: bus type pnp registered [ 20.419457] pnp: PnP ACPI: found 10 devices [ 20.419459] ACPI: ACPI bus type pnp unregistered [ 20.419668] PCI: Using ACPI for IRQ routing [ 20.419670] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 20.419678] PCI: Cannot allocate resource region 7 of bridge 0000:00:05.0 [ 20.419680] PCI: Cannot allocate resource region 8 of bridge 0000:00:05.0 [ 20.428811] NET: Registered protocol family 8 [ 20.428813] NET: Registered protocol family 20 [ 20.428923] AppArmor: AppArmor Filesystem Enabled [ 20.432781] Time: tsc clocksource has been installed. [ 20.440809] system 00:01: iomem range 0xe0000000-0xefffffff could not be reserved [ 20.440812] system 00:01: iomem range 0xfec00000-0xfec00fff could not be reserved [ 20.440815] system 00:01: iomem range 0xfee00000-0xfee00fff could not be reserved [ 20.440823] system 00:08: ioport range 0x1080-0x1080 has been reserved [ 20.440826] system 00:08: ioport range 0x220-0x22f has been reserved [ 20.440828] system 00:08: ioport range 0x40b-0x40b has been reserved [ 20.440831] system 00:08: ioport range 0x4d0-0x4d1 has been reserved [ 20.440834] system 00:08: ioport range 0x4d6-0x4d6 has been reserved [ 20.440836] system 00:08: ioport range 0x530-0x537 has been reserved [ 20.440839] system 00:08: ioport range 0xc00-0xc01 has been reserved [ 20.440841] system 00:08: ioport range 0xc14-0xc14 has been reserved [ 20.440844] system 00:08: ioport range 0xc50-0xc52 has been reserved [ 20.440847] system 00:08: ioport range 0xc6c-0xc6c has been reserved [ 20.440849] system 00:08: ioport range 0xc6f-0xc6f has been reserved [ 20.440852] system 00:08: ioport range 0xcd0-0xcd3 has been reserved [ 20.440854] system 00:08: ioport range 0xcd4-0xcd5 has been reserved [ 20.440857] system 00:08: ioport range 0xcd6-0xcd7 has been reserved [ 20.440860] system 00:08: ioport range 0xcd8-0xcdf has been reserved [ 20.440862] system 00:08: ioport range 0x8000-0x805f has been reserved [ 20.440865] system 00:08: ioport range 0xf40-0xf47 has been reserved [ 20.440868] system 00:08: ioport range 0x87f-0x87f has been reserved [ 20.440874] system 00:09: iomem range 0xe0000-0xfffff could not be reserved [ 20.440877] system 00:09: iomem range 0xfff00000-0xffffffff could not be reserved [ 20.440880] system 00:09: iomem range 0xc0004800-0xc0004bff has been reserved [ 20.440882] system 00:09: iomem range 0xfed00000-0xfed003ff has been reserved [ 20.440885] system 00:09: iomem range 0x0-0xfff could not be reserved [ 20.441230] PCI: Bridge: 0000:00:01.0 [ 20.441233] IO window: 9000-9fff [ 20.441236] MEM window: c0100000-c01fffff [ 20.441238] PREFETCH window: c8000000-cfffffff [ 20.441240] PCI: Bridge: 0000:00:05.0 [ 20.441242] IO window: disabled. [ 20.441244] MEM window: disabled. [ 20.441246] PREFETCH window: disabled. [ 20.441248] PCI: Bridge: 0000:00:06.0 [ 20.441249] IO window: disabled. [ 20.441252] MEM window: c0200000-c02fffff [ 20.441253] PREFETCH window: disabled. [ 20.441257] PCI: Bridge: 0000:00:14.4 [ 20.441258] IO window: disabled. [ 20.441263] MEM window: c0300000-c03fffff [ 20.441267] PREFETCH window: disabled. [ 20.441287] PCI: Setting latency timer of device 0000:00:05.0 to 64 [ 20.441293] PCI: Setting latency timer of device 0000:00:06.0 to 64 [ 20.441343] NET: Registered protocol family 2 [ 20.476858] IP route cache hash table entries: 65536 (order: 7, 524288 bytes) [ 20.477575] TCP established hash table entries: 262144 (order: 10, 4194304 bytes) [ 20.479607] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 20.480153] TCP: Hash tables configured (established 262144 bind 65536) [ 20.480157] TCP reno registered [ 20.488884] checking if image is initramfs... it is [ 20.944512] Switched to high resolution mode on CPU 0 [ 21.083880] Freeing initrd memory: 7558k freed [ 21.088490] audit: initializing netlink socket (disabled) [ 21.088503] audit(1222742619.168:1): initialized [ 21.090260] VFS: Disk quotas dquot_6.5.1 [ 21.090327] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 21.090450] io scheduler noop registered [ 21.090451] io scheduler anticipatory registered [ 21.090453] io scheduler deadline registered [ 21.090538] io scheduler cfq registered (default) [ 21.090545] PCI: MSI quirk detected. MSI deactivated. [ 21.091327] Boot video device is 0000:01:05.0 [ 21.091496] PCI: Setting latency timer of device 0000:00:05.0 to 64 [ 21.091515] assign_interrupt_mode Found MSI capability [ 21.091518] Allocate Port Service[0000:00:05.0:pcie00] [ 21.091550] Allocate Port Service[0000:00:05.0:pcie02] [ 21.091602] PCI: Setting latency timer of device 0000:00:06.0 to 64 [ 21.091620] assign_interrupt_mode Found MSI capability [ 21.091622] Allocate Port Service[0000:00:06.0:pcie00] [ 21.091650] Allocate Port Service[0000:00:06.0:pcie02] [ 21.116256] Real Time Clock Driver v1.12ac [ 21.116341] Linux agpgart interface v0.102 [ 21.116344] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 21.117289] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 21.117349] input: Macintosh mouse button emulation as /devices/virtual/input/input0 [ 21.117430] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12 [ 21.119495] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 21.119499] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 21.124572] mice: PS/2 mouse device common for all mice [ 21.124611] cpuidle: using governor ladder [ 21.124613] cpuidle: using governor menu [ 21.124750] NET: Registered protocol family 1 [ 21.124842] registered taskstats version 1 [ 21.124969] Magic number: 8:167:714 [ 21.125107] /build/buildd/linux-2.6.24/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 21.125110] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 21.125113] EDD information not available. [ 21.125120] Freeing unused kernel memory: 320k freed [ 21.164360] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 [ 22.399649] fuse init (API version 7.9) [ 22.611458] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) [ 22.611465] ACPI: Processor [CPU0] (supports 8 throttling states) [ 22.611478] ACPI Exception (processor_core-0822): AE_NOT_FOUND, Processor Device is not present [20070126] [ 22.621791] ACPI: Thermal Zone [THRM] (56 C) [ 23.495830] SCSI subsystem initialized [ 23.546904] libata version 3.00 loaded. [ 23.555945] usbcore: registered new interface driver usbfs [ 23.555966] usbcore: registered new interface driver hub [ 23.567590] ahci 0000:00:12.0: version 3.0 [ 23.567619] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 22 [ 23.567709] ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit [ 23.567716] ahci 0000:00:12.0: controller can't do PMP, turning off CAP_PMP [ 23.578914] usbcore: registered new device driver usb [ 23.590318] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 23.591266] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 23.602245] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver [ 24.254514] Marking TSC unstable due to TSC halts in idle [ 24.258456] Time: acpi_pm clocksource has been installed. [ 24.570340] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode [ 24.570345] ahci 0000:00:12.0: flags: ncq sntf ilck led clo pio [ 24.571399] scsi0 : ahci [ 24.571700] scsi1 : ahci [ 24.571835] scsi2 : ahci [ 24.571973] scsi3 : ahci [ 24.572048] ata1: SATA max UDMA/133 abar m1024@0xc0004000 port 0xc0004100 irq 22 [ 24.572053] ata2: SATA max UDMA/133 abar m1024@0xc0004000 port 0xc0004180 irq 22 [ 24.572057] ata3: SATA max UDMA/133 abar m1024@0xc0004000 port 0xc0004200 irq 22 [ 24.572061] ata4: SATA max UDMA/133 abar m1024@0xc0004000 port 0xc0004280 irq 22 [ 25.046601] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 25.047507] ata1.00: ATA-7: Hitachi HTS541680J9SA00, SB2OC74P, max UDMA/100 [ 25.047510] ata1.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 25.048576] ata1.00: configured for UDMA/100 [ 25.357842] ata2: SATA link down (SStatus 0 SControl 300) [ 25.669653] ata3: SATA link down (SStatus 0 SControl 300) [ 25.981463] ata4: SATA link down (SStatus 0 SControl 300) [ 25.981576] scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54168 SB2O PQ: 0 ANSI: 5 [ 25.983061] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 25.983143] ohci_hcd 0000:00:13.0: OHCI Host Controller [ 25.983386] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1 [ 25.983408] ohci_hcd 0000:00:13.0: irq 16, io mem 0xc0005000 [ 25.989915] Driver 'sd' needs updating - please use bus_type methods [ 25.989999] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) [ 25.990010] sd 0:0:0:0: [sda] Write Protect is off [ 25.990013] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 25.990026] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 25.990065] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) [ 25.990073] sd 0:0:0:0: [sda] Write Protect is off [ 25.990075] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 25.990087] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 25.990091] sda:<6>usb usb1: configuration #1 chosen from 1 choice [ 26.037584] hub 1-0:1.0: USB hub found [ 26.037594] hub 1-0:1.0: 2 ports detected [ 26.141455] ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 17 (level, low) -> IRQ 17 [ 26.141554] ohci_hcd 0000:00:13.1: OHCI Host Controller [ 26.141619] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2 [ 26.141641] ohci_hcd 0000:00:13.1: irq 17, io mem 0xc0006000 [ 26.197424] usb usb2: configuration #1 chosen from 1 choice [ 26.197446] hub 2-0:1.0: USB hub found [ 26.197455] hub 2-0:1.0: 2 ports detected [ 26.301338] ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 18 (level, low) -> IRQ 18 [ 26.301438] ohci_hcd 0000:00:13.2: OHCI Host Controller [ 26.301511] ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3 [ 26.301534] ohci_hcd 0000:00:13.2: irq 18, io mem 0xc0007000 [ 26.357347] usb usb3: configuration #1 chosen from 1 choice [ 26.357370] hub 3-0:1.0: USB hub found [ 26.357379] hub 3-0:1.0: 2 ports detected [ 26.370318] sda1 sda2 sda3 [ 26.370400] sd 0:0:0:0: [sda] Attached SCSI disk [ 26.375010] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 26.457184] usb 1-1: new full speed USB device using ohci_hcd and address 2 [ 26.461241] ACPI: PCI Interrupt 0000:00:13.3[B] -> GSI 17 (level, low) -> IRQ 17 [ 26.461337] ohci_hcd 0000:00:13.3: OHCI Host Controller [ 26.461396] ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 4 [ 26.461414] ohci_hcd 0000:00:13.3: irq 17, io mem 0xc0008000 [ 26.518300] usb usb4: configuration #1 chosen from 1 choice [ 26.518322] hub 4-0:1.0: USB hub found [ 26.518331] hub 4-0:1.0: 2 ports detected [ 26.621162] ACPI: PCI Interrupt 0000:00:13.4[C] -> GSI 18 (level, low) -> IRQ 18 [ 26.621255] ohci_hcd 0000:00:13.4: OHCI Host Controller [ 26.621315] ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 5 [ 26.621334] ohci_hcd 0000:00:13.4: irq 18, io mem 0xc0009000 [ 26.677154] usb usb5: configuration #1 chosen from 1 choice [ 26.677178] hub 5-0:1.0: USB hub found [ 26.677187] hub 5-0:1.0: 2 ports detected [ 26.678150] usb 1-1: configuration #1 chosen from 1 choice [ 26.781424] ACPI: PCI Interrupt 0000:00:13.5[D] -> GSI 19 (level, low) -> IRQ 19 [ 26.781510] ehci_hcd 0000:00:13.5: EHCI Host Controller [ 26.781573] ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 6 [ 26.781615] ehci_hcd 0000:00:13.5: debug port 1 [ 26.781631] ehci_hcd 0000:00:13.5: irq 19, io mem 0xc0004400 [ 26.792991] ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 26.793126] usb usb6: configuration #1 chosen from 1 choice [ 26.793147] hub 6-0:1.0: USB hub found [ 26.793154] hub 6-0:1.0: 10 ports detected [ 26.897066] SB600_PATA: IDE controller (0x1002:0x438c rev 0x00) at PCI slot 0000:00:14.1 [ 26.897081] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16 [ 26.897091] SB600_PATA: not 100% native mode: will probe irqs later [ 26.897099] ide0: BM-DMA at 0x8420-0x8427, BIOS settings: hda:DMA, hdb:pio [ 26.897110] Probing IDE interface ide0... [ 27.304648] usb 6-1: new high speed USB device using ehci_hcd and address 2 [ 27.438088] usb 6-1: configuration #1 chosen from 1 choice [ 27.860287] usb 6-7: new high speed USB device using ehci_hcd and address 4 [ 28.304359] hda: TSSTcorp DVD+/-RW TS-L632D, ATAPI CD/DVD-ROM drive [ 28.304396] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4 [ 28.304716] hda: UDMA/33 mode selected [ 28.305191] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 28.331699] ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 18 (level, low) -> IRQ 18 [ 28.331710] PCI: Setting latency timer of device 0000:05:00.0 to 64 [ 28.348042] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x11, vendor 0x4243) [ 28.348053] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0A, vendor 0x4243) [ 28.348060] ssb: Core 2 found: USB 1.1 Host (cc 0x817, rev 0x03, vendor 0x4243) [ 28.348066] ssb: Core 3 found: PCI-E (cc 0x820, rev 0x01, vendor 0x4243) [ 28.387984] ssb: Sonics Silicon Backplane found on PCI device 0000:05:00.0 [ 28.397681] ACPI: PCI Interrupt 0000:08:00.0[A] -> GSI 21 (level, low) -> IRQ 21 [ 28.416021] ssb: Core 0 found: Fast Ethernet (cc 0x806, rev 0x07, vendor 0x4243) [ 28.416032] ssb: Core 1 found: V90 (cc 0x807, rev 0x03, vendor 0x4243) [ 28.416039] ssb: Core 2 found: PCI (cc 0x804, rev 0x0A, vendor 0x4243) [ 28.455925] ssb: Sonics Silicon Backplane found on PCI device 0000:08:00.0 [ 28.455951] b44.c:v2.0 [ 28.476186] eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:19:b9:5e:2d:38 [ 28.517126] hda: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache [ 28.517133] Uniform CD-ROM driver Revision: 3.20 [ 30.097388] usb 6-7: configuration #1 chosen from 1 choice [ 30.097754] usb 1-1: USB disconnect, address 2 [ 30.097924] usbcore: registered new interface driver libusual [ 30.102656] Initializing USB Mass Storage driver... [ 30.534458] usb 2-1: new low speed USB device using ohci_hcd and address 2 [ 30.754702] usb 2-1: configuration #1 chosen from 1 choice [ 30.779659] scsi4 : SCSI emulation for USB Mass Storage devices [ 30.782472] usb-storage: device found at 2 [ 30.782476] usb-storage: waiting for device to settle before scanning [ 30.783678] scsi5 : SCSI emulation for USB Mass Storage devices [ 30.784031] usbcore: registered new interface driver usb-storage [ 30.784035] USB Mass Storage support registered. [ 30.784149] usbcore: registered new interface driver hiddev [ 30.784181] usb-storage: device found at 4 [ 30.784182] usb-storage: waiting for device to settle before scanning [ 30.787797] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:13.1/usb2/2-1/2-1:1.0/input/input2 [ 30.798355] input,hidraw0: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:13.1-1 [ 30.805581] Fixing up Logitech keyboard report descriptor [ 30.806108] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:13.1/usb2/2-1/2-1:1.1/input/input3 [ 30.830314] input,hiddev96,hidraw1: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:13.1-1 [ 30.830330] usbcore: registered new interface driver usbhid [ 30.830334] /build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 35.779428] usb-storage: device scan complete [ 35.779511] usb-storage: device scan complete [ 35.779933] scsi 4:0:0:0: Direct-Access WD 3200BEV External 1.05 PQ: 0 ANSI: 4 [ 35.781416] scsi 5:0:0:0: Direct-Access WDC WD12 00VE-22KWT0 0000 PQ: 0 ANSI: 0 [ 35.785035] sd 5:0:0:0: [sdb] 234441648 512-byte hardware sectors (120034 MB) [ 35.785913] sd 5:0:0:0: [sdb] Write Protect is off [ 35.785918] sd 5:0:0:0: [sdb] Mode Sense: 27 00 00 00 [ 35.785921] sd 5:0:0:0: [sdb] Assuming drive cache: write through [ 35.786897] sd 5:0:0:0: [sdb] 234441648 512-byte hardware sectors (120034 MB) [ 35.787789] sd 5:0:0:0: [sdb] Write Protect is off [ 35.787793] sd 5:0:0:0: [sdb] Mode Sense: 27 00 00 00 [ 35.787795] sd 5:0:0:0: [sdb] Assuming drive cache: write through [ 35.787800] sdb: sdb1 sdb2 < sdb5 > [ 36.180571] sd 5:0:0:0: [sdb] Attached SCSI disk [ 36.180607] sd 5:0:0:0: Attached scsi generic sg1 type 0 [ 36.183003] sd 4:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB) [ 36.183874] sd 4:0:0:0: [sdc] Write Protect is off [ 36.183878] sd 4:0:0:0: [sdc] Mode Sense: 21 00 00 00 [ 36.183880] sd 4:0:0:0: [sdc] Assuming drive cache: write through [ 36.184868] sd 4:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB) [ 36.185743] sd 4:0:0:0: [sdc] Write Protect is off [ 36.185748] sd 4:0:0:0: [sdc] Mode Sense: 21 00 00 00 [ 36.185751] sd 4:0:0:0: [sdc] Assuming drive cache: write through [ 36.185755] sdc:Attempting manual resume [ 36.594900] swsusp: Resume From Partition 8:21 [ 36.594902] PM: Checking swsusp image. [ 36.595562] PM: Resume from disk failed. [ 36.612923] EXT3-fs: INFO: recovery required on readonly filesystem. [ 36.612928] EXT3-fs: write access will be enabled during recovery. [ 37.665612] kjournald starting. Commit interval 5 seconds [ 37.665629] EXT3-fs: sdb1: orphan cleanup on readonly fs [ 37.665635] ext3_orphan_cleanup: deleting unreferenced inode 5498472 [ 37.665676] ext3_orphan_cleanup: deleting unreferenced inode 344080 [ 37.665682] EXT3-fs: sdb1: 2 orphan inodes deleted [ 37.665684] EXT3-fs: recovery complete. [ 37.693570] EXT3-fs: mounted filesystem with ordered data mode. [ 40.008849] sdc1 [ 40.008915] sd 4:0:0:0: [sdc] Attached SCSI disk [ 40.008950] sd 4:0:0:0: Attached scsi generic sg2 type 0 [ 49.838617] input: PC Speaker as /devices/platform/pcspkr/input/input4 [ 50.002432] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 50.044492] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 50.285568] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device [ 50.406230] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 50.450751] input: Power Button (FF) as /devices/virtual/input/input5 [ 50.462114] ACPI: Power Button (FF) [PWRF] [ 50.462220] input: Power Button (CM) as /devices/virtual/input/input6 [ 50.478082] ACPI: Power Button (CM) [PWRB] [ 50.478200] input: Sleep Button (CM) as /devices/virtual/input/input7 [ 50.494083] ACPI: Sleep Button (CM) [SLPB] [ 50.494192] input: Lid Switch as /devices/virtual/input/input8 [ 50.495751] ACPI: Lid Switch [LID] [ 50.497175] ACPI: AC Adapter [ACAD] (on-line) [ 50.753960] ricoh-mmc: Ricoh MMC Controller disabling driver [ 50.753964] ricoh-mmc: Copyright(c) Philip Langdale [ 50.754011] ricoh-mmc: Ricoh MMC controller found at 0000:08:01.1 [1180:0843] (rev 1) [ 50.754016] ricoh-mmc: Main firewire function not found. Cannot disable controller. [ 50.944691] sdhci: Secure Digital Host Controller Interface driver [ 50.944696] sdhci: Copyright(c) Pierre Ossman [ 50.944744] sdhci: SDHCI controller found at 0000:08:01.0 [1180:0822] (rev 19) [ 50.944771] ACPI: PCI Interrupt 0000:08:01.0[B] -> GSI 20 (level, low) -> IRQ 20 [ 50.944872] sdhci:slot0: Will use DMA mode even though HW doesn't fully claim to support it. [ 50.944963] mmc0: SDHCI at 0xc0302800 irq 20 DMA [ 51.389677] ACPI: Battery Slot [BAT1] (battery present) [ 51.389728] ACPI: WMI-Acer: Mapper loaded [ 51.785752] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x180b1, caps: 0xa04713/0x200000 [ 51.821084] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input9 [ 51.997181] ndiswrapper version 1.52 loaded (smp=yes, preempt=no) [ 52.076311] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:1b/LNXVIDEO:00/input/input10 [ 52.101146] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no) [ 52.354525] [fglrx] Maximum main memory to use for locked dma buffers: 1766 MBytes. [ 52.354556] [fglrx] ASYNCIO init succeed! [ 52.354665] [fglrx] PAT is enabled successfully! [ 52.362338] [fglrx] module loaded - fglrx 8.47.3 [Feb 25 2008] on minor 0 [ 52.396681] usbcore: registered new interface driver ndiswrapper [ 52.424995] ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16 [ 52.913992] b43-phy0: Broadcom 4311 WLAN found [ 52.956604] b43-phy0 debug: Found PHY: Analog 4, Type 2, Revision 8 [ 52.956624] b43-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2 [ 52.988209] phy0: Selected rate control algorithm 'simple' [ 55.365212] lp: driver loaded but no devices found [ 56.191322] Adding 4803392k swap on /dev/sdb5. Priority:-1 extents:1 across:4803392k [ 56.731645] EXT3 FS on sdb1, internal journal [ 57.955127] ip_tables: (C) 2000-2006 Netfilter Core Team [ 58.581182] No dock devices found. [ 58.845949] powernow-k8: Found 1 AMD Turion(tm) 64 Mobile Technology MK-36 processors (1 cpu cores) (version 2.20.00) [ 58.845989] powernow-k8: 0 : fid 0xc (2000 MHz), vid 0xe [ 58.845991] powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x10 [ 58.845993] powernow-k8: 2 : fid 0x8 (1600 MHz), vid 0x12 [ 58.845995] powernow-k8: 3 : fid 0x0 (800 MHz), vid 0x18 [ 60.157078] ppdev: user-space parallel port driver [ 60.475932] audit(1222742660.302:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5538 profile="/usr/sbin/cupsd" namespace="default" [ 61.155175] Clocksource tsc unstable (delta = -260304135 ns) [ 61.374373] NET: Registered protocol family 10 [ 61.374729] lo: Disabled Privacy Extensions [ 62.286852] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 62.351431] input: b43-phy0 as /devices/virtual/input/input11 [ 62.429349] Bluetooth: Core ver 2.11 [ 62.433327] NET: Registered protocol family 31 [ 62.433331] Bluetooth: HCI device and connection manager initialized [ 62.433335] Bluetooth: HCI socket layer initialized [ 62.464170] Bluetooth: L2CAP ver 2.9 [ 62.464173] Bluetooth: L2CAP socket layer initialized [ 62.503548] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02) [ 62.549305] Bluetooth: RFCOMM socket layer initialized [ 62.549475] Bluetooth: RFCOMM TTY layer initialized [ 62.549477] Bluetooth: RFCOMM ver 1.8 [ 64.000081] b43-phy0 debug: Chip initialized [ 64.000465] b43-phy0 debug: 32-bit DMA initialized [ 64.021526] Registered led device: b43-phy0:tx [ 64.021759] Registered led device: b43-phy0:rx [ 64.021891] Registered led device: b43-phy0:radio [ 64.021925] b43-phy0 debug: Wireless interface started [ 64.067769] b43-phy0 debug: Adding Interface type 2 [ 64.070002] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 65.129229] ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 17 (level, low) -> IRQ 17 [ 66.843380] [fglrx] GART Table is not in FRAME_BUFFER range [ 66.843390] [fglrx] Reserve Block - 0 offset = 0X0 length = 0X40000 [ 66.843393] [fglrx] Reserve Block - 1 offset = 0X7ff5000 length = 0Xb000 [ 67.047911] [fglrx] interrupt source 20008000 successfully enabled [ 67.047917] [fglrx] enable ID = 0x00000004 [ 67.048183] [fglrx] Receive enable interrupt message with irqEnableMask: 20008000 [ 71.409541] hda-intel: Invalid position buffer, using LPIB read method instead. [ 129.907320] NET: Registered protocol family 17 [ 136.578209] wlan0: Initial auth_alg=0 [ 136.578216] wlan0: authenticate with AP 00:17:9a:90:e1:3a [ 136.579279] wlan0: RX authentication from 00:17:9a:90:e1:3a (alg=0 transaction=2 status=0) [ 136.579284] wlan0: authenticated [ 136.579286] wlan0: associate with AP 00:17:9a:90:e1:3a [ 136.597594] wlan0: RX AssocResp from 00:17:9a:90:e1:3a (capab=0x471 status=0 aid=1) [ 136.597599] wlan0: associated [ 136.597604] wlan0: switched to short barker preamble (BSSID=00:17:9a:90:e1:3a) [ 136.598806] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 142.912783] wlan0: no IPv6 routers present [ 148.263476] wlan0: no IPv6 routers present [ 153.956343] usb 6-5: new high speed USB device using ehci_hcd and address 5 [ 154.009786] usb 6-5: configuration #1 chosen from 1 choice [ 154.010122] hub 6-5:1.0: USB hub found [ 154.010355] hub 6-5:1.0: 4 ports detected [ 154.137258] usb 6-5.3: new high speed USB device using ehci_hcd and address 6 [ 154.174576] usb 6-5.3: configuration #1 chosen from 1 choice [ 154.175052] hub 6-5.3:1.0: USB hub found [ 154.175244] hub 6-5.3:1.0: 4 ports detected [ 160.674535] usb 6-5.1: new full speed USB device using ehci_hcd and address 7 [ 165.926644] usb 6-5.1: configuration #1 chosen from 1 choice [ 166.232521] Bluetooth: HCI USB driver ver 2.9 [ 166.233041] usbcore: registered new interface driver hci_usb [ 195.796228] usb 6-5.1: USB disconnect, address 7