[ 0.000000] Linux version 2.6.20-8-generic (root@vernadsky) (gcc version 4.1.2 20070129 (prerelease) (Ubuntu 4.1.1-31ubuntu2)) #2 SMP Tue Feb 13 05:18:42 UTC 2007 (Ubuntu 2.6.20-8.14-generic) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] sanitize start [ 0.000000] sanitize end [ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1 [ 0.000000] copy_e820_map() type is E820_RAM [ 0.000000] copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2 [ 0.000000] copy_e820_map() start: 00000000000e4000 size: 000000000001c000 end: 0000000000100000 type: 2 [ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000007fea0000 end: 000000007ffa0000 type: 1 [ 0.000000] copy_e820_map() type is E820_RAM [ 0.000000] copy_e820_map() start: 000000007ffa0000 size: 000000000000e000 end: 000000007ffae000 type: 3 [ 0.000000] copy_e820_map() start: 000000007ffae000 size: 0000000000032000 end: 000000007ffe0000 type: 4 [ 0.000000] copy_e820_map() start: 000000007ffe0000 size: 0000000000020000 end: 0000000080000000 type: 2 [ 0.000000] copy_e820_map() start: 00000000ffb80000 size: 0000000000480000 end: 0000000100000000 type: 2 [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000007ffa0000 (usable) [ 0.000000] BIOS-e820: 000000007ffa0000 - 000000007ffae000 (ACPI data) [ 0.000000] BIOS-e820: 000000007ffae000 - 000000007ffe0000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved) [ 0.000000] BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved) [ 0.000000] 1151MB HIGHMEM available. [ 0.000000] 896MB LOWMEM available. [ 0.000000] found SMP MP-table at 000ff780 [ 0.000000] Entering add_active_range(0, 0, 524192) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] HighMem 229376 -> 524192 [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 524192 [ 0.000000] On node 0 totalpages: 524192 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1760 pages used for memmap [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 [ 0.000000] HighMem zone: 2303 pages used for memmap [ 0.000000] HighMem zone: 292513 pages, LIFO batch:31 [ 0.000000] DMI 2.3 present. [ 0.000000] ACPI: RSDP (v002 ACPIAM ) @ 0x000fad50 [ 0.000000] ACPI: XSDT (v001 A M I OEMXSDT 0x09000626 MSFT 0x00000097) @ 0x7ffa0100 [ 0.000000] ACPI: FADT (v003 A M I OEMFACP 0x09000626 MSFT 0x00000097) @ 0x7ffa0290 [ 0.000000] ACPI: MADT (v001 A M I OEMAPIC 0x09000626 MSFT 0x00000097) @ 0x7ffa0390 [ 0.000000] ACPI: OEMB (v001 A M I AMI_OEM 0x09000626 MSFT 0x00000097) @ 0x7ffae040 [ 0.000000] ACPI: MCFG (v001 A M I OEMMCFG 0x09000626 MSFT 0x00000097) @ 0x7ffa8730 [ 0.000000] ACPI: DSDT (v001 A0402 A0402000 0x00000000 INTL 0x02002026) @ 0x00000000 [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] Processor #0 6:15 APIC version 20 [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) [ 0.000000] Processor #1 6:15 APIC version 20 [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:7fb80000) [ 0.000000] Detected 2404.215 MHz processor. [ 26.411288] Built 1 zonelists. Total pages: 520097 [ 26.411291] Kernel command line: root=UUID=a4305dac-9181-4170-992c-24c729909082 ro quiet splash [ 26.411391] mapped APIC to ffffd000 (fee00000) [ 26.411392] mapped IOAPIC to ffffc000 (fec00000) [ 26.411394] Enabling fast FPU save and restore... done. [ 26.411396] Enabling unmasked SIMD FPU exception support... done. [ 26.411402] Initializing CPU#0 [ 26.411447] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 26.412598] Console: colour VGA+ 80x25 [ 26.412770] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 26.412966] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 26.464937] Memory: 2068184k/2096768k available (1979k kernel code, 27312k reserved, 882k data, 324k init, 1179264k highmem) [ 26.464944] virtual kernel memory layout: [ 26.464945] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB) [ 26.464946] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 26.464946] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) [ 26.464947] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 26.464948] .init : 0xc03d1000 - 0xc0422000 ( 324 kB) [ 26.464948] .data : 0xc02eecb4 - 0xc03cb6d4 ( 882 kB) [ 26.464949] .text : 0xc0100000 - 0xc02eecb4 (1979 kB) [ 26.464951] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 26.543170] Calibrating delay using timer specific routine.. 4811.88 BogoMIPS (lpj=9623765) [ 26.543200] Security Framework v1.0.0 initialized [ 26.543205] SELinux: Disabled at boot. [ 26.543216] Mount-cache hash table entries: 512 [ 26.543322] CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0000e3bd 00000000 00000001 [ 26.543328] monitor/mwait feature present. [ 26.543329] using mwait in idle threads. [ 26.543333] CPU: L1 I cache: 32K, L1 D cache: 32K [ 26.543334] CPU: L2 cache: 4096K [ 26.543337] CPU: Physical Processor ID: 0 [ 26.543338] CPU: Processor Core ID: 0 [ 26.543339] CPU: After all inits, caps: bfebfbff 20000000 00000000 00003940 0000e3bd 00000000 00000001 [ 26.543355] Checking 'hlt' instruction... OK. [ 26.559229] SMP alternatives: switching to UP code [ 26.559467] ACPI: Core revision 20060707 [ 26.575469] CPU0: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06 [ 26.575485] SMP alternatives: switching to SMP code [ 26.575541] Booting processor 1/1 eip 3000 [ 26.585987] Initializing CPU#1 [ 26.662911] Calibrating delay using timer specific routine.. 4808.56 BogoMIPS (lpj=9617138) [ 26.662916] CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0000e3bd 00000000 00000001 [ 26.662920] monitor/mwait feature present. [ 26.662922] CPU: L1 I cache: 32K, L1 D cache: 32K [ 26.662923] CPU: L2 cache: 4096K [ 26.662925] CPU: Physical Processor ID: 0 [ 26.662925] CPU: Processor Core ID: 1 [ 26.662927] CPU: After all inits, caps: bfebfbff 20000000 00000000 00003940 0000e3bd 00000000 00000001 [ 26.663457] CPU1: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06 [ 26.663471] Total of 2 processors activated (9620.45 BogoMIPS). [ 26.663611] ENABLING IO-APIC IRQs [ 26.663773] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 26.810602] checking TSC synchronization across 2 CPUs: passed. [ 0.003990] Brought up 2 CPUs [ 0.174560] migration_cost=29 [ 0.174754] Booting paravirtualized kernel on bare hardware [ 0.174810] Time: 7:29:19 Date: 01/15/107 [ 0.174830] NET: Registered protocol family 16 [ 0.174890] EISA bus registered [ 0.174893] ACPI: bus type pci registered [ 0.174899] PCI: BIOS Bug: MCFG area at f0000000 is not E820-reserved [ 0.174932] PCI: Not using MMCONFIG. [ 0.175194] PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=4 [ 0.175195] PCI: Using configuration type 1 [ 0.175196] Setting up standard PCI resources [ 0.188110] ACPI: Interpreter enabled [ 0.188112] ACPI: Using IOAPIC for interrupt routing [ 0.188786] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.188791] PCI: Probing PCI hardware (bus 00) [ 0.189315] PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO [ 0.189318] PCI quirk: region 0480-04bf claimed by ICH6 GPIO [ 0.189496] Boot video device is 0000:04:00.0 [ 0.189765] PCI: Transparent bridge - 0000:00:1e.0 [ 0.189808] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.191478] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] [ 0.191688] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT] [ 0.191912] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] [ 0.192383] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT] [ 0.196935] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 12 14 15) [ 0.197116] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15) [ 0.197295] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 *6 7 10 11 12 14 15) [ 0.197473] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15) [ 0.197651] ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 6 7 10 11 12 14 15) [ 0.197830] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 0.198009] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 0.198189] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15) [ 0.198266] Linux Plug and Play Support v0.97 (c) Adam Belay [ 0.198274] pnp: PnP ACPI init [ 0.201794] pnp: PnP ACPI: found 15 devices [ 0.201797] PnPBIOS: Disabled by ACPI PNP [ 0.201829] PCI: Using ACPI for IRQ routing [ 0.201830] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 0.212461] pnp: 00:07: ioport range 0x290-0x297 has been reserved [ 0.212639] PCI: Bridge: 0000:00:01.0 [ 0.212641] IO window: e000-efff [ 0.212644] MEM window: ddf00000-dfffffff [ 0.212646] PREFETCH window: e0000000-efffffff [ 0.212648] PCI: Bridge: 0000:00:1c.0 [ 0.212650] IO window: d000-dfff [ 0.212654] MEM window: disabled. [ 0.212656] PREFETCH window: disabled. [ 0.212660] PCI: Bridge: 0000:00:1c.3 [ 0.212662] IO window: c000-cfff [ 0.212665] MEM window: dde00000-ddefffff [ 0.212668] PREFETCH window: disabled. [ 0.212671] PCI: Bridge: 0000:00:1e.0 [ 0.212673] IO window: b000-bfff [ 0.212677] MEM window: disabled. [ 0.212679] PREFETCH window: disabled. [ 0.212690] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 0.212693] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 0.212706] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 0.212710] PCI: Setting latency timer of device 0000:00:1c.0 to 64 [ 0.212724] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 17 [ 0.212728] PCI: Setting latency timer of device 0000:00:1c.3 to 64 [ 0.212736] PCI: Setting latency timer of device 0000:00:1e.0 to 64 [ 0.212754] NET: Registered protocol family 2 [ 0.251678] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.251754] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.252094] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.252264] TCP: Hash tables configured (established 131072 bind 65536) [ 0.252266] TCP reno registered [ 0.263764] checking if image is initramfs... it is [ 0.670653] Freeing initrd memory: 6408k freed [ 0.671121] audit: initializing netlink socket (disabled) [ 0.671134] audit(1171524559.140:1): initialized [ 0.671200] highmem bounce pool size: 64 pages [ 0.671255] VFS: Disk quotas dquot_6.5.1 [ 0.671272] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.671309] io scheduler noop registered [ 0.671311] io scheduler anticipatory registered [ 0.671313] io scheduler deadline registered [ 0.671320] io scheduler cfq registered (default) [ 0.671489] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 0.671515] assign_interrupt_mode Found MSI capability [ 0.671541] Allocate Port Service[0000:00:01.0:pcie00] [ 0.671606] PCI: Setting latency timer of device 0000:00:1c.0 to 64 [ 0.671639] assign_interrupt_mode Found MSI capability [ 0.671663] Allocate Port Service[0000:00:1c.0:pcie00] [ 0.671689] Allocate Port Service[0000:00:1c.0:pcie02] [ 0.671765] PCI: Setting latency timer of device 0000:00:1c.3 to 64 [ 0.671797] assign_interrupt_mode Found MSI capability [ 0.671822] Allocate Port Service[0000:00:1c.3:pcie00] [ 0.671938] isapnp: Scanning for PnP cards... [ 1.024021] isapnp: No Plug & Play device found [ 1.038302] Real Time Clock Driver v1.12ac [ 1.038342] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 1.038438] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 1.038875] 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 1.038979] mice: PS/2 mouse device common for all mice [ 1.039373] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 1.039442] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 1.039445] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 1.039624] PNP: No PS/2 controller found. Probing ports directly. [ 1.042306] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.042309] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 1.042372] EISA: Probing bus 0 at eisa.0 [ 1.042394] Cannot allocate resource for EISA slot 8 [ 1.042395] EISA: Detected 0 cards. [ 1.072394] TCP cubic registered [ 1.072400] NET: Registered protocol family 1 [ 1.072403] NET: Registered protocol family 8 [ 1.072405] NET: Registered protocol family 20 [ 1.072429] Starting balanced_irq [ 1.072433] Using IPI No-Shortcut mode [ 1.072523] ACPI: (supports S0 S1 S3 S4 S5) [ 1.072557] Magic number: 11:766:470 [ 1.072706] Freeing unused kernel memory: 324k freed [ 1.073686] Time: tsc clocksource has been installed. [ 2.215258] Capability LSM initialized [ 2.237561] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ AMI] OemTableId [ CPU1PM] [20060707] [ 2.237836] ACPI: Processor [CPU1] (supports 8 throttling states) [ 2.237973] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ AMI] OemTableId [ CPU2PM] [20060707] [ 2.238232] ACPI: Processor [CPU2] (supports 8 throttling states) [ 2.517814] usbcore: registered new interface driver usbfs [ 2.517831] usbcore: registered new interface driver hub [ 2.517847] usbcore: registered new device driver usb [ 2.518418] USB Universal Host Controller Interface driver v3.0 [ 2.518466] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 18 [ 2.518474] PCI: Setting latency timer of device 0000:00:1d.0 to 64 [ 2.518476] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 2.518559] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 2.518585] uhci_hcd 0000:00:1d.0: irq 18, io base 0x00008000 [ 2.518660] usb usb1: configuration #1 chosen from 1 choice [ 2.518676] hub 1-0:1.0: USB hub found [ 2.518680] hub 1-0:1.0: 2 ports detected [ 2.626467] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 19 [ 2.626474] PCI: Setting latency timer of device 0000:00:1d.1 to 64 [ 2.626477] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 2.626547] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 [ 2.626570] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00008400 [ 2.626834] usb usb2: configuration #1 chosen from 1 choice [ 2.626923] hub 2-0:1.0: USB hub found [ 2.626927] hub 2-0:1.0: 2 ports detected [ 2.730588] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 20 [ 2.730593] PCI: Setting latency timer of device 0000:00:1d.2 to 64 [ 2.730596] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 2.730608] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 [ 2.730629] uhci_hcd 0000:00:1d.2: irq 20, io base 0x00008800 [ 2.730685] usb usb3: configuration #1 chosen from 1 choice [ 2.730703] hub 3-0:1.0: USB hub found [ 2.730707] hub 3-0:1.0: 2 ports detected [ 2.835001] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 17 [ 2.835008] PCI: Setting latency timer of device 0000:00:1d.3 to 64 [ 2.835011] uhci_hcd 0000:00:1d.3: UHCI Host Controller [ 2.835030] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 [ 2.835053] uhci_hcd 0000:00:1d.3: irq 17, io base 0x00009000 [ 2.835134] usb usb4: configuration #1 chosen from 1 choice [ 2.835161] hub 4-0:1.0: USB hub found [ 2.835166] hub 4-0:1.0: 2 ports detected [ 2.939907] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 18 [ 2.939917] PCI: Setting latency timer of device 0000:00:1d.7 to 64 [ 2.939921] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 2.939940] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 [ 2.939966] ehci_hcd 0000:00:1d.7: debug port 1 [ 2.939972] PCI: cache line size of 32 is not supported by device 0000:00:1d.7 [ 2.939977] ehci_hcd 0000:00:1d.7: irq 18, io mem 0xdddffc00 [ 2.943865] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 2.943912] usb usb5: configuration #1 chosen from 1 choice [ 2.943930] hub 5-0:1.0: USB hub found [ 2.943933] hub 5-0:1.0: 8 ports detected [ 2.971798] usb 2-1: new low speed USB device using uhci_hcd and address 2 [ 3.048650] ICH7: IDE controller at PCI slot 0000:00:1f.1 [ 3.048661] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 22 (level, low) -> IRQ 21 [ 3.048671] ICH7: chipset revision 1 [ 3.048672] ICH7: not 100% native mode: will probe irqs later [ 3.048682] ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio [ 3.048694] ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio [ 3.048703] Probing IDE interface ide0... [ 3.784486] hda: LITE-ON DVDRW LH-18A1H, ATAPI CD/DVD-ROM drive [ 4.086636] usb 2-1: new low speed USB device using uhci_hcd and address 3 [ 4.261046] usb 2-1: configuration #1 chosen from 1 choice [ 4.457405] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 4.457431] Probing IDE interface ide1... [ 4.505319] usb 2-2: new low speed USB device using uhci_hcd and address 4 [ 4.695087] usb 2-2: configuration #1 chosen from 1 choice [ 4.940170] usb 4-1: new full speed USB device using uhci_hcd and address 2 [ 5.028434] r8169 Gigabit Ethernet driver 2.2LK loaded [ 5.028453] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 19 (level, low) -> IRQ 17 [ 5.028476] PCI: Setting latency timer of device 0000:02:00.0 to 64 [ 5.028640] eth0: RTL8168b/8111b at 0xf8856000, 00:18:f3:a3:75:21, IRQ 17 [ 5.035544] SCSI subsystem initialized [ 5.038382] libata version 2.00 loaded. [ 5.039243] ata_piix 0000:00:1f.2: version 2.00ac7 [ 5.039246] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] [ 5.039263] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 23 (level, low) -> IRQ 22 [ 5.039272] PCI: Setting latency timer of device 0000:00:1f.2 to 64 [ 5.039295] ata1: SATA max UDMA/133 cmd 0xA800 ctl 0xA402 bmdma 0x9400 irq 22 [ 5.039311] ata2: SATA max UDMA/133 cmd 0xA000 ctl 0x9802 bmdma 0x9408 irq 22 [ 5.039319] scsi0 : ata_piix [ 5.207600] ata1.00: ATA-7, max UDMA7, 625142448 sectors: LBA48 NCQ (depth 0/32) [ 5.207602] ata1.00: ata1: dev 0 multi count 16 [ 5.219620] ata1.00: configured for UDMA/133 [ 5.219629] scsi1 : ata_piix [ 5.343610] usb 4-1: configuration #1 chosen from 1 choice [ 5.346801] usbcore: registered new interface driver hiddev [ 5.361648] input: Logitech USB Mouse as /class/input/input0 [ 5.361667] input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:1d.1-1 [ 5.385331] ATA: abnormal status 0x7F on port 0xA007 [ 5.385455] input: Microsoft Comfort Curve Keyboard 2000 as /class/input/input1 [ 5.385461] input: USB HID v1.11 Keyboard [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-2 [ 5.385508] scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD321KJ CP10 PQ: 0 ANSI: 5 [ 5.391177] SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB) [ 5.391185] sda: Write Protect is off [ 5.391186] sda: Mode Sense: 00 3a 00 00 [ 5.391195] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.391226] SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB) [ 5.391232] sda: Write Protect is off [ 5.391233] sda: Mode Sense: 00 3a 00 00 [ 5.391247] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.391249] sda:<6>hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(66) [ 5.398616] Uniform CD-ROM driver Revision: 3.20 [ 5.405547] input: Microsoft Comfort Curve Keyboard 2000 as /class/input/input2 [ 5.405554] input: USB HID v1.11 Device [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-2 [ 5.405566] usbcore: registered new interface driver usbhid [ 5.405568] drivers/usb/input/hid-core.c: v2.6:USB HID core driver [ 5.434088] sda1 sda2 sda3 [ 5.453848] sd 0:0:0:0: Attached scsi disk sda [ 5.456274] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 5.573985] Attempting manual resume [ 5.573988] swsusp: Resume From Partition 8:3 [ 5.573989] PM: Checking swsusp image. [ 5.574124] PM: Resume from disk failed. [ 5.607526] kjournald starting. Commit interval 5 seconds [ 5.607534] EXT3-fs: mounted filesystem with ordered data mode. [ 10.370636] r8169: eth0: link up [ 10.370642] r8169: eth0: link up [ 10.831941] NET: Registered protocol family 10 [ 10.832006] lo: Disabled Privacy Extensions [ 11.138877] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 11.162199] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 11.171398] intel_rng: FWH not detected [ 11.327776] Linux agpgart interface v0.101 (c) Dave Jones [ 11.328824] agpgart: Detected an Intel 945G Chipset. [ 11.343196] agpgart: AGP aperture is 256M @ 0x0 [ 11.344739] input: PC Speaker as /class/input/input3 [ 11.434570] Bluetooth: Core ver 2.11 [ 11.434790] NET: Registered protocol family 31 [ 11.434791] Bluetooth: HCI device and connection manager initialized [ 11.434794] Bluetooth: HCI socket layer initialized [ 11.477839] parport: PnPBIOS parport detected. [ 11.477938] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA] [ 11.488236] iTCO_vendor_support: vendor-support=0 [ 11.488975] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (11-Nov-2006) [ 11.489020] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0860) [ 11.489045] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 11.506864] Bluetooth: HCI USB driver ver 2.9 [ 11.577758] nvidia: module license 'NVIDIA' taints kernel. [ 11.831940] usbcore: registered new interface driver hci_usb [ 11.862304] ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 11.862312] PCI: Setting latency timer of device 0000:04:00.0 to 64 [ 11.862386] NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-9631 Thu Nov 9 17:38:10 PST 2006 [ 11.958421] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 19 (level, low) -> IRQ 17 [ 11.958436] PCI: Setting latency timer of device 0000:00:1b.0 to 64 [ 12.333949] fuse init (API version 7.8) [ 12.352081] lp0: using parport0 (interrupt-driven). [ 12.370480] Adding 8474276k swap on /dev/disk/by-uuid/894411be-ce65-417f-8be0-c5f1d8feefb9. Priority:-1 extents:1 across:8474276k [ 12.509719] EXT3 FS on sda1, internal journal [ 12.685251] kjournald starting. Commit interval 5 seconds [ 12.685551] EXT3 FS on sda2, internal journal [ 12.685557] EXT3-fs: mounted filesystem with ordered data mode. [ 13.105519] ibm_acpi: ec object not found [ 13.139500] Using specific hotkey driver [ 13.179734] input: Power Button (FF) as /class/input/input4 [ 13.179754] ACPI: Power Button (FF) [PWRF] [ 13.179800] input: Power Button (CM) as /class/input/input5 [ 13.179813] ACPI: Power Button (CM) [PWRB] [ 13.262207] No dock devices found. [ 13.753345] ppdev: user-space parallel port driver [ 14.922817] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) [ 14.922820] apm: disabled - APM is not SMP safe. [ 17.648984] Bluetooth: L2CAP ver 2.8 [ 17.648988] Bluetooth: L2CAP socket layer initialized [ 17.749374] Bluetooth: RFCOMM socket layer initialized [ 17.749383] Bluetooth: RFCOMM TTY layer initialized [ 17.749385] Bluetooth: RFCOMM ver 1.8 [ 19.024216] **WARNING** I2C adapter driver [NVIDIA i2c adapter 0 at 4:00.0] forgot to specify physical device; fix it! [ 19.025350] **WARNING** I2C adapter driver [NVIDIA i2c adapter 1 at 4:00.0] forgot to specify physical device; fix it! [ 19.026118] **WARNING** I2C adapter driver [NVIDIA i2c adapter 2 at 4:00.0] forgot to specify physical device; fix it! [ 21.134480] eth0: no IPv6 routers present