[ 0.000000] Linux version 2.6.20-6-generic (root@palmer) (gcc version 4.1.2 20070106 (prerelease) (Ubuntu 4.1.1-21ubuntu7)) #2 SMP Wed Jan 31 20:53:39 UTC 2007 (Ubuntu 2.6.20-6.11-generic) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] sanitize start [ 0.000000] sanitize end [ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009f000 end: 000000000009f000 type: 1 [ 0.000000] copy_e820_map() type is E820_RAM [ 0.000000] copy_e820_map() start: 000000000009f000 size: 0000000000001000 end: 00000000000a0000 type: 2 [ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000002fec9000 end: 000000002ffc9000 type: 1 [ 0.000000] copy_e820_map() type is E820_RAM [ 0.000000] copy_e820_map() start: 000000002ffc9000 size: 0000000000037000 end: 0000000030000000 type: 2 [ 0.000000] copy_e820_map() start: 00000000feda0000 size: 0000000000060000 end: 00000000fee00000 type: 2 [ 0.000000] copy_e820_map() start: 00000000ffb00000 size: 0000000000500000 end: 0000000100000000 type: 2 [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable) [ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000002ffc9000 (usable) [ 0.000000] BIOS-e820: 000000002ffc9000 - 0000000030000000 (reserved) [ 0.000000] BIOS-e820: 00000000feda0000 - 00000000fee00000 (reserved) [ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) [ 0.000000] 0MB HIGHMEM available. [ 0.000000] 767MB LOWMEM available. [ 0.000000] Entering add_active_range(0, 0, 196553) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 196553 [ 0.000000] HighMem 196553 -> 196553 [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 196553 [ 0.000000] On node 0 totalpages: 196553 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1503 pages used for memmap [ 0.000000] Normal zone: 190954 pages, LIFO batch:31 [ 0.000000] HighMem zone: 0 pages used for memmap [ 0.000000] DMI 2.3 present. [ 0.000000] ACPI: RSDP (v000 DELL ) @ 0x000fdf00 [ 0.000000] ACPI: RSDT (v001 DELL CPi R 0x27d40a12 ASL 0x00000061) @ 0x2fff0000 [ 0.000000] ACPI: FADT (v001 DELL CPi R 0x27d40a12 ASL 0x00000061) @ 0x2fff0400 [ 0.000000] ACPI: DSDT (v001 INT430 SYSFexxx 0x00001001 MSFT 0x0100000e) @ 0x00000000 [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] Allocating PCI resources starting at 40000000 (gap: 30000000:ceda0000) [ 0.000000] Detected 2657.865 MHz processor. [ 36.059466] Built 1 zonelists. Total pages: 195018 [ 36.059472] Kernel command line: BOOT_IMAGE=/casper/vmlinuz file=/cdrom/preseed/kubuntu.seed boot=casper initrd=/casper/initrd.gz quiet splash -- [ 36.059670] Local APIC disabled by BIOS -- you can enable it with "lapic" [ 36.059682] mapped APIC to ffffd000 (0160c000) [ 36.059686] Enabling fast FPU save and restore... done. [ 36.059689] Enabling unmasked SIMD FPU exception support... done. [ 36.059705] Initializing CPU#0 [ 36.059814] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 36.061181] Console: colour VGA+ 80x25 [ 36.062186] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 36.063165] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 36.081821] Memory: 768484k/786212k available (1975k kernel code, 17236k reserved, 878k data, 324k init, 0k highmem) [ 36.081832] virtual kernel memory layout: [ 36.081833] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB) [ 36.081834] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 36.081835] vmalloc : 0xf0800000 - 0xff7fe000 ( 239 MB) [ 36.081836] lowmem : 0xc0000000 - 0xeffc9000 ( 767 MB) [ 36.081837] .init : 0xc03cf000 - 0xc0420000 ( 324 kB) [ 36.081838] .data : 0xc02edd14 - 0xc03c96d4 ( 878 kB) [ 36.081839] .text : 0xc0100000 - 0xc02edd14 (1975 kB) [ 36.081843] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 36.159752] Calibrating delay using timer specific routine.. 5320.05 BogoMIPS (lpj=10640112) [ 36.159799] Security Framework v1.0.0 initialized [ 36.159805] SELinux: Disabled at boot. [ 36.159823] Mount-cache hash table entries: 512 [ 36.159983] CPU: After generic identify, caps: bfebf9ff 00000000 00000000 00000000 00004400 00000000 00000000 [ 36.159996] CPU: Trace cache: 12K uops, L1 D cache: 8K [ 36.159999] CPU: L2 cache: 512K [ 36.160001] CPU: Hyper-Threading is disabled [ 36.160004] CPU: After all inits, caps: bfebf9ff 00000000 00000000 00003080 00004400 00000000 00000000 [ 36.160026] Checking 'hlt' instruction... OK. [ 36.175842] SMP alternatives: switching to UP code [ 36.176073] Freeing SMP alternatives: 11k freed [ 36.176171] ACPI: Core revision 20060707 [ 36.186082] ACPI: setting ELCR to 0200 (from 0800) [ 36.186905] CPU0: Intel(R) Pentium(R) 4 CPU 2.66GHz stepping 09 [ 36.186912] SMP motherboard not detected. [ 36.186915] Local APIC not detected. Using dummy APIC emulation. [ 36.186970] Brought up 1 CPUs [ 36.187283] Booting paravirtualized kernel on bare hardware [ 36.187359] NET: Registered protocol family 16 [ 36.187477] EISA bus registered [ 36.187482] ACPI: bus type pci registered [ 36.239981] PCI: PCI BIOS revision 2.10 entry at 0xfcfae, last bus=2 [ 36.239983] PCI: Using configuration type 1 [ 36.239985] Setting up standard PCI resources [ 36.252503] ACPI: Interpreter enabled [ 36.252508] ACPI: Using PIC for interrupt routing [ 36.253129] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 36.253139] PCI: Probing PCI hardware (bus 00) [ 36.253222] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 [ 36.258282] * The chipset may have PM-Timer Bug. Due to workarounds for a bug, [ 36.258284] * this clock source is slow. If you are sure your timer does not have [ 36.258285] * this bug, please use "acpi_pm_good" to disable the workaround [ 36.258332] PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO [ 36.258335] PCI quirk: region 0880-08bf claimed by ICH4 GPIO [ 36.258571] Boot video device is 0000:01:00.0 [ 36.258816] PCI: Transparent bridge - 0000:00:1e.0 [ 36.258877] PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#02) (try 'pci=assign-busses') [ 36.258880] Please report the result to linux-kernel to fix this permanently [ 36.258901] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 36.267413] ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11) [ 36.267660] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *11 [ 36.267920] ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 *11) [ 36.268162] ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 *11) [ 36.268407] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 36.268654] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 36.269068] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] [ 36.270021] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT] [ 36.270352] Linux Plug and Play Support v0.97 (c) Adam Belay [ 36.270366] pnp: PnP ACPI init [ 36.281119] pnp: PnP ACPI: found 11 devices [ 36.281126] PnPBIOS: Disabled by ACPI PNP [ 36.281190] PCI: Using ACPI for IRQ routing [ 36.281194] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 36.293249] pnp: 00:02: ioport range 0x4d0-0x4d1 has been reserved [ 36.293253] pnp: 00:02: ioport range 0x800-0x805 could not be reserved [ 36.293256] pnp: 00:02: ioport range 0x808-0x80f could not be reserved [ 36.293263] pnp: 00:03: ioport range 0xf400-0xf4fe has been reserved [ 36.293265] pnp: 00:03: ioport range 0x806-0x807 has been reserved [ 36.293268] pnp: 00:03: ioport range 0x810-0x85f could not be reserved [ 36.293271] pnp: 00:03: ioport range 0x860-0x87f has been reserved [ 36.293273] pnp: 00:03: ioport range 0x880-0x8bf has been reserved [ 36.293276] pnp: 00:03: ioport range 0x8c0-0x8df has been reserved [ 36.293286] pnp: 00:08: ioport range 0x900-0x97f has been reserved [ 36.293578] PCI: Bridge: 0000:00:01.0 [ 36.293582] IO window: c000-cfff [ 36.293587] MEM window: fc000000-fdffffff [ 36.293591] PREFETCH window: e8000000-efffffff [ 36.293602] PCI: Bus 3, cardbus bridge: 0000:02:04.0 [ 36.293604] IO window: 0000d000-0000d0ff [ 36.293608] IO window: 0000d400-0000d4ff [ 36.293613] PREFETCH window: 40000000-43ffffff [ 36.293617] MEM window: 48000000-4bffffff [ 36.293621] PCI: Bridge: 0000:00:1e.0 [ 36.293624] IO window: d000-efff [ 36.293630] MEM window: f6000000-fbffffff [ 36.293634] PREFETCH window: 40000000-43ffffff [ 36.293653] PCI: Setting latency timer of device 0000:00:1e.0 to 64 [ 36.293668] PCI: Enabling device 0000:02:04.0 (0000 -> 0003) [ 36.293856] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 [ 36.293859] PCI: setting IRQ 11 as level-triggered [ 36.293863] ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 [ 36.293900] NET: Registered protocol family 2 [ 36.331736] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 36.332002] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 36.333336] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 36.333981] TCP: Hash tables configured (established 131072 bind 65536) [ 36.333987] TCP reno registered [ 36.343844] checking if image is initramfs... it is [ 36.908739] Freeing initrd memory: 6632k freed [ 36.909215] audit: initializing netlink socket (disabled) [ 36.909234] audit(1170766427.032:1): initialized [ 36.909390] VFS: Disk quotas dquot_6.5.1 [ 36.909413] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 36.909476] io scheduler noop registered [ 36.909479] io scheduler anticipatory registered [ 36.909482] io scheduler deadline registered [ 36.909491] io scheduler cfq registered (default) [ 36.909801] isapnp: Scanning for PnP cards... [ 37.262558] isapnp: No Plug & Play device found [ 37.291928] Real Time Clock Driver v1.12ac [ 37.291994] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 37.293021] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 7 [ 37.293026] PCI: setting IRQ 7 as level-triggered [ 37.293029] ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 7 (level, low) -> IRQ 7 [ 37.293039] ACPI: PCI interrupt for device 0000:00:1f.6 disabled [ 37.293129] mice: PS/2 mouse device common for all mice [ 37.293757] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 37.293962] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 37.293967] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 37.294180] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 37.294373] i8042.c: Warning: Keylock active. [ 37.297847] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 37.297857] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 37.298056] EISA: Probing bus 0 at eisa.0 [ 37.298083] EISA: Detected 0 cards. [ 37.328178] TCP cubic registered [ 37.328185] NET: Registered protocol family 1 [ 37.328193] NET: Registered protocol family 8 [ 37.328195] NET: Registered protocol family 20 [ 37.328240] Using IPI No-Shortcut mode [ 37.328318] ACPI: (supports S0 S1 S3 S4 S5) [ 37.328839] Freeing unused kernel memory: 324k freed [ 37.329524] input: AT Translated Set 2 keyboard as /class/input/input0 [ 37.330972] Time: tsc clocksource has been installed. [ 38.546111] Capability LSM initialized [ 38.585258] ACPI: Processor [CPU0] (supports 8 throttling states) [ 38.588927] ACPI: Thermal Zone [THM] (56 C) [ 39.104651] usbcore: registered new interface driver usbfs [ 39.104679] usbcore: registered new interface driver hub [ 39.104707] usbcore: registered new device driver usb [ 39.105746] USB Universal Host Controller Interface driver v3.0 [ 39.105830] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 [ 39.105845] PCI: Setting latency timer of device 0000:00:1d.0 to 64 [ 39.105850] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 39.106035] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 39.106063] uhci_hcd 0000:00:1d.0: irq 11, io base 0x0000bf80 [ 39.106183] usb usb1: configuration #1 chosen from 1 choice [ 39.106213] hub 1-0:1.0: USB hub found [ 39.106221] hub 1-0:1.0: 2 ports detected [ 39.191717] ieee1394: Initialized config rom entry `ip1394' [ 39.210126] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11 [ 39.210132] ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 [ 39.210146] PCI: Setting latency timer of device 0000:00:1d.1 to 64 [ 39.210150] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 39.210177] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 [ 39.210203] uhci_hcd 0000:00:1d.1: irq 11, io base 0x0000bf40 [ 39.210310] usb usb2: configuration #1 chosen from 1 choice [ 39.210342] hub 2-0:1.0: USB hub found [ 39.210351] hub 2-0:1.0: 2 ports detected [ 39.314095] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11 [ 39.314100] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 [ 39.314114] PCI: Setting latency timer of device 0000:00:1d.2 to 64 [ 39.314118] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 39.314147] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 [ 39.314173] uhci_hcd 0000:00:1d.2: irq 11, io base 0x0000bf20 [ 39.314283] usb usb3: configuration #1 chosen from 1 choice [ 39.314311] hub 3-0:1.0: USB hub found [ 39.314321] hub 3-0:1.0: 2 ports detected [ 39.420918] ICH4: IDE controller at PCI slot 0000:00:1f.1 [ 39.420929] PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) [ 39.420941] ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 [ 39.420954] ICH4: chipset revision 2 [ 39.420956] ICH4: not 100% native mode: will probe irqs later [ 39.420968] ide0: BM-DMA at 0xbfa0-0xbfa7, BIOS settings: hda:DMA, hdb:pio [ 39.420983] ide1: BM-DMA at 0xbfa8-0xbfaf, BIOS settings: hdc:DMA, hdd:pio [ 39.420994] Probing IDE interface ide0... [ 39.553493] usb 2-1: new low speed USB device using uhci_hcd and address 2 [ 39.730885] usb 2-1: configuration #1 chosen from 1 choice [ 39.745344] usbcore: registered new interface driver hiddev [ 39.759048] input: Kensington Kensington USB Wheel Mouse as /class/input/input1 [ 39.759163] input: USB HID v1.10 Mouse [Kensington Kensington USB Wheel Mouse] on usb-0000:00:1d.1-1 [ 39.759181] usbcore: registered new interface driver usbhid [ 39.759185] drivers/usb/input/hid-core.c: v2.6:USB HID core driver [ 40.157239] hda: TEAC CD-RW CD-W224E, ATAPI CD/DVD-ROM drive [ 40.493390] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 40.493613] Probing IDE interface ide1... [ 40.780821] hdc: IC25N040ATCS05-0, ATA DISK drive [ 41.452732] ide1 at 0x170-0x177,0x376 on irq 15 [ 41.460104] SCSI subsystem initialized [ 41.465897] libata version 2.00 loaded. [ 41.471380] b44.c:v1.01 (Jun 16, 2006) [ 41.471406] ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNKB] -> GSI 7 (level, low) -> IRQ 7 [ 41.475090] eth0: Broadcom 4400 10/100BaseT Ethernet 00:0d:56:ae:93:89 [ 41.475204] ACPI: PCI Interrupt 0000:02:04.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 [ 41.529528] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11 [ 41.529533] ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11 [ 41.529557] PCI: Setting latency timer of device 0000:00:1d.7 to 64 [ 41.529562] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 41.529853] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4 [ 41.529900] ehci_hcd 0000:00:1d.7: debug port 1 [ 41.529907] PCI: cache line size of 128 is not supported by device 0000:00:1d.7 [ 41.529918] ehci_hcd 0000:00:1d.7: irq 11, io mem 0xf4fffc00 [ 41.533810] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 41.534723] usb usb4: configuration #1 chosen from 1 choice [ 41.534938] hub 4-0:1.0: USB hub found [ 41.534955] hub 4-0:1.0: 6 ports detected [ 41.535601] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[faffd800-faffdfff] Max Packet=[2048] IR/IT contexts=[4/8] [ 41.557229] hda: ATAPI 24X CD-ROM CD-R/RW drive, 1280kB Cache, DMA [ 41.557240] Uniform CD-ROM driver Revision: 3.20 [ 41.568642] hdc: max request size: 128KiB [ 41.580213] usb 2-1: USB disconnect, address 2 [ 41.796524] hdc: 78140160 sectors (40007 MB) w/7898KiB Cache, CHS=65535/16/63, UDMA(100) [ 41.796534] hdc: cache flushes not supported [ 41.796586] hdc: hdc1 hdc2 < hdc5 hdc6 hdc7 > [ 42.282804] ISO 9660 Extensions: Microsoft Joliet Level 3 [ 42.323652] usb 2-1: new low speed USB device using uhci_hcd and address 3 [ 42.390001] ISO 9660 Extensions: RRIP_1991A [ 42.492878] Registering unionfs 20060916-2203 [ 42.492883] unionfs: debugging is not enabled [ 42.501459] usb 2-1: configuration #1 chosen from 1 choice [ 42.517430] input: Kensington Kensington USB Wheel Mouse as /class/input/input2 [ 42.517452] input: USB HID v1.10 Mouse [Kensington Kensington USB Wheel Mouse] on usb-0000:00:1d.1-1 [ 42.530276] loop: loaded (max 8 devices) [ 42.652872] squashfs: version 3.1 (2006/08/19) Phillip Lougher [ 42.803505] ieee1394: Host added: ID:BUS[0-00:1023] GUID[324fc0001e45b861] [ 157.640624] Linux agpgart interface v0.101 (c) Dave Jones [ 158.816447] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 161.124917] iTCO_vendor_support: vendor-support=0 [ 161.332683] input: PC Speaker as /class/input/input3 [ 162.313760] agpgart: Detected an Intel 845G Chipset. [ 162.320094] agpgart: AGP aperture is 128M @ 0xe0000000 [ 162.666922] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 162.688749] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (11-Nov-2006) [ 163.280793] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x254ab1, caps: 0x804713/0x0 [ 163.323693] input: SynPS/2 Synaptics TouchPad as /class/input/input4 [ 163.327366] iTCO_wdt: Found a ICH4 TCO device (Version=1, TCOBASE=0x0860) [ 163.327867] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 164.191841] intel_rng: FWH not detected [ 164.380878] NET: Registered protocol family 17 [ 166.996487] Yenta: CardBus bridge found at 0000:02:04.0 [1028:0149] [ 166.996508] Yenta: Using CSCINT to route CSC interrupts to PCI [ 166.996510] Yenta: Routing CardBus interrupts to PCI [ 166.996515] Yenta TI: socket 0000:02:04.0, mfunc 0x00001002, devctl 0x64 [ 167.228775] Yenta: ISA IRQ mask 0x0478, PCI irq 11 [ 167.228780] Socket status: 30000020 [ 167.228784] Yenta: Raising subordinate bus# of parent bus (#02) from #02 to #06 [ 167.228791] pcmcia: parent PCI bridge I/O window: 0xd000 - 0xefff [ 167.228794] cs: IO port probe 0xd000-0xefff: clean. [ 167.229211] pcmcia: parent PCI bridge Memory window: 0xf6000000 - 0xfbffffff [ 167.229214] pcmcia: parent PCI bridge Memory window: 0x40000000 - 0x43ffffff [ 167.596536] ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 7 (level, low) -> IRQ 7 [ 167.596568] PCI: Setting latency timer of device 0000:00:1f.5 to 64 [ 167.863789] pccard: CardBus card inserted into slot 0 [ 167.936897] ath_hal: module license 'Proprietary' taints kernel. [ 167.938504] ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) [ 168.415391] intel8x0_measure_ac97_clock: measured 55216 usecs [ 168.415396] intel8x0: clocking to 48000 [ 169.517813] wlan: 0.8.4.2 (0.9.2.1) [ 169.724876] ath_rate_sample: 1.2 (0.9.2.1) [ 170.154903] ath_pci: 0.9.4.5 (0.9.2.1) [ 170.155401] PCI: Enabling device 0000:03:00.0 (0000 -> 0002) [ 170.155414] ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 [ 170.155497] BUG: unable to handle kernel NULL pointer dereference at virtual address 00000000 [ 170.155557] printing eip: [ 170.155583] f0b93018 [ 170.155584] *pde = 00000000 [ 170.155612] Oops: 0002 [#1] [ 170.155637] SMP [ 170.155706] Modules linked in: ath_pci ath_rate_sample wlan ath_hal(P) pcmcia joydev snd_intel8x0 snd_ac97_codec ac97_bus snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_dummy snd_seq_oss yenta_socket snd_seq_midi snd_rawmidi snd_seq_midi_event rsrc_nonstatic snd_seq pcmcia_core af_packet iTCO_wdt psmouse serio_raw shpchp intel_agp snd_timer snd_seq_device pcspkr snd iTCO_vendor_support soundcore snd_page_alloc tsdev pci_hotplug agpgart evdev squashfs loop unionfs nls_cp437 isofs ide_disk ide_cd cdrom ata_piix ata_generic libata scsi_mod usbhid hid piix ehci_hcd ohci1394 ieee1394 b44 mii generic uhci_hcd usbcore thermal processor fan fbcon tileblit font bitblit softcursor vesafb capability commoncap [ 170.157412] CPU: 0 [ 170.157413] EIP: 0060:[] Tainted: P VLI [ 170.157414] EFLAGS: 00010286 (2.6.20-6-generic #2) [ 170.157505] EIP is at ath_attach+0x148/0x1530 [ath_pci] [ 170.157541] eax: 00000000 ebx: 0000001a ecx: 00000000 edx: e7881dd3 [ 170.157577] esi: e7224000 edi: e81c0400 ebp: e81c0400 esp: e7881d44 [ 170.157613] ds: 007b es: 007b ss: 0068 [ 170.157647] Process modprobe (pid: 4992, ti=e7880000 task=e7bbc560 task.ti=e7880000) [ 170.157684] Stack: f0be0000 e7881dcc 00000000 00000000 00000000 00000000 00000000 00000000 [ 170.157924] e81c0000 001a0000 e81c1a38 00000000 00000000 00000000 00000000 00000000 [ 170.158164] 00000000 00000000 00000000 00000000 0000000b e68df240 00000080 c03c0b80 [ 170.158404] Call Trace: [ 170.158505] [] setup_irq+0xf1/0x1e0 [ 170.158568] [] ath_pci_probe+0x0/0x370 [ath_pci] [ 170.158640] [] ath_intr+0x0/0xb50 [ath_pci] [ 170.158711] [] ath_pci_probe+0x1d3/0x370 [ath_pci] [ 170.158778] [] sysfs_create_link+0x6e/0x160 [ 170.158848] [] ath_pci_probe+0x0/0x370 [ath_pci] [ 170.158915] [] pci_device_probe+0x56/0x80 [ 170.158978] [] really_probe+0x54/0x140 [ 170.159038] [] driver_probe_device+0x49/0xc0 [ 170.159108] [] __driver_attach+0x9e/0xa0 [ 170.159170] [] bus_for_each_dev+0x3b/0x60 [ 170.159239] [] driver_attach+0x16/0x20 [ 170.159296] [] __driver_attach+0x0/0xa0 [ 170.159352] [] bus_add_driver+0x7b/0x1a0 [ 170.159423] [] __pci_register_driver+0x74/0xc0 [ 170.159485] [] init_ath_pci+0x30/0x54 [ath_pci] [ 170.159550] [] sys_init_module+0x15d/0x1ba0 [ 170.159688] [] sys_mmap2+0xcd/0xd0 [ 170.159761] [] syscall_call+0x7/0xb [ 170.159833] [] unix_gc+0xa3/0x3c0 [ 170.159903] ======================= [ 170.159935] Code: 89 40 04 c7 85 a4 17 00 00 e0 76 b9 f0 8b 54 24 20 8d 84 24 88 00 00 00 89 44 24 04 8b 42 1c 89 ea 89 04 24 89 d8 e8 58 a2 01 00 <01> 00 00 00 24 2c 0f 84 98 05 00 00 8b 5c 24 2c 8b 43 04 3d 00 [ 170.161418] EIP: [] ath_attach+0x148/0x1530 [ath_pci] SS:ESP 0068:e7881d44 [ 170.161510] <6>cs: IO port probe 0x100-0x3af: clean. [ 172.031588] cs: IO port probe 0x3e0-0x4ff: clean. [ 172.032080] cs: IO port probe 0x820-0x8ff: clean. [ 172.032208] cs: IO port probe 0xc00-0xcf7: clean. [ 172.032745] cs: IO port probe 0xa00-0xaff: clean. [ 172.487598] fuse init (API version 7.8) [ 184.551035] ACPI: AC Adapter [AC] (on-line) [ 185.120249] ACPI: Battery Slot [BAT0] (battery present) [ 185.196069] input: Lid Switch as /class/input/input5 [ 185.196549] ACPI: Lid Switch [LID] [ 185.197005] input: Power Button (CM) as /class/input/input6 [ 185.197212] ACPI: Power Button (CM) [PBTN] [ 185.197593] input: Sleep Button (CM) as /class/input/input7 [ 185.197790] ACPI: Sleep Button (CM) [SBTN] [ 185.428888] No dock devices found. [ 185.451741] Using specific hotkey driver [ 185.513532] ibm_acpi: ec object not found [ 185.569263] toshiba_acpi: Unknown parameter `hotkeys_over_acpi' [ 185.588877] ACPI: Video Device [VID] (multi-head: yes rom: no post: no) [ 185.589158] ACPI: Video Device [VID] (multi-head: yes rom: no post: no) [ 185.589211] ACPI: Video Device [VID2] (multi-head: yes rom: no post: no) [ 210.633722] NET: Registered protocol family 10 [ 210.633837] lo: Disabled Privacy Extensions [ 210.633892] ADDRCONF(NETDEV_UP): eth0: link is not ready