[  334.086351] pci 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[  334.281568] [drm] Initialized drm 1.1.0 20060810
[  334.452711] pci 0000:04:00.0: setting latency timer to 64
[  334.452862] [drm] Initialized radeon 1.31.0 20080528 for 0000:04:00.0 on minor 0
[  335.253100] [drm] Setting GART location based on new memory map
[  335.253334] [drm] Loading RV610 CP Microcode
[  335.253339] platform r600_cp.0: firmware: requesting radeon/RV610_pfp.bin
[  335.330463] platform r600_cp.0: firmware: requesting radeon/RV610_me.bin
[  335.477437] [drm] Resetting GPU
[  335.477496] [drm] writeback test succeeded in 1 usecs
[  338.642515] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[  338.642519] vboxdrv: Successfully done.
[  338.642521] vboxdrv: Found 2 processor cores.
[  338.643036] VBoxDrv: dbg - g_abExecMemory=ffffffffa02f4480
[  338.643057] vboxdrv: fAsync=0 offMin=0x160 offMax=0x8da
[  338.643594] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[  338.643597] vboxdrv: Successfully loaded version 3.1.6 (interface 0x00100001).
[  341.625001] CPU0 attaching NULL sched-domain.
[  341.625007] CPU1 attaching NULL sched-domain.
[  341.660140] CPU0 attaching sched-domain:
[  341.660147]  domain 0: span 0-1 level MC
[  341.660152]   groups: 0 1
[  341.660161] CPU1 attaching sched-domain:
[  341.660165]  domain 0: span 0-1 level MC
[  341.660169]   groups: 1 0
[  345.137744] usb 3-2: usbfs: interface 0 claimed by usblp while 'usb' sets config #1
[  346.442056] hda-intel: IRQ timing workaround is activated for card #1. Suggest a bigger bdl_pos_adj.
[  349.768914]   alloc irq_desc for 27 on node -1
[  349.768918]   alloc kstat_irqs on node -1
[  349.768933] atl1 0000:02:00.0: irq 27 for MSI/MSI-X
[  349.769045] atl1 0000:02:00.0: eth0 link is up 100 Mbps full duplex
[  353.705178] atl1 0000:02:00.0: irq 27 for MSI/MSI-X
[  353.705233] atl1 0000:02:00.0: eth0 link is up 100 Mbps full duplex
[  364.560042] eth0: no IPv6 routers present
[ 4661.790062] usb 3-2: USB disconnect, address 2
[ 4661.790289] usblp0: removed
[ 5003.710025] usb 3-2: new full speed USB device using uhci_hcd and address 3
[ 5003.912153] usb 3-2: configuration #1 chosen from 1 choice
[ 5003.919094] usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x04F9 pid 0x0206
[ 5003.919875] scsi6 : SCSI emulation for USB Mass Storage devices
[ 5003.920302] usb-storage: device found at 3
[ 5003.920307] usb-storage: waiting for device to settle before scanning
[ 5005.183249] usb 3-2: usbfs: interface 0 claimed by usblp while 'usb' sets config #1
[ 5008.921822] usb-storage: device scan complete
[ 5008.936806] scsi 6:0:0:0: Direct-Access     Brother  DCP-145C         1.00 PQ: 0 ANSI: 2
[ 5008.937964] sd 6:0:0:0: Attached scsi generic sg6 type 0
[ 5009.016789] sd 6:0:0:0: [sdf] Attached SCSI removable disk
[ 6170.150147] [drm] Resetting GPU
[ 8576.290050] usb 3-2: USB disconnect, address 3
[ 8576.290267] usblp0: removed