Ubuntu
linux-source-2.6.15 package

Alternative firmware needed for LG LW5400N wifi card based on TI acx111

Bug #35703 reported by McPolu
8
Affects Status Importance Assigned to Milestone
linux-source-2.6.15 (Ubuntu)
Fix Released
Medium
Unassigned

Bug Description

PCMCIA wifi card from LG, model LW5400N does not work by default in dapper fligth 5. This card contains a Texas Instrument ACX111 chip. It is handled by acx driver.

Problem is that driver defaults to 2.3.1.31 firmware version which does not work for this card. Forcing firmware version 1.2.1.34 fix the defect. This defect is related to the following defects:

#30766: which I think should be now moved to "Confirmed".
#26703: Some comments in this defect point to the firmware version problem
#23787: which I think should be now moved to "Confirmed".

However, being a different card from a different manufacturer I open a new, different defect.

Creation of a new bug report is required in /lib/firmware/2.6.15-18-686/acx/readme.txt if default firmware does not work. It also asks for the output
of "lspci -vv", "lspci -vvn" and "lsusb" so here we go:

lspci -vv:

0000:00:00.0 Host bridge: Silicon Integrated Systems [SiS] 645xx (rev 11)
 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
 Latency: 32
 Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=64M]
 Capabilities: [c0] AGP version 3.5
  Status: RQ=32 Iso- ArqSz=2 Cal=3 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
  Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4

0000:00:01.0 PCI bridge: Silicon Integrated Systems [SiS] SiS AGP Port (virtual PCI-to-PCI bridge) (prog-if 00 [Normal decode])
 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 64
 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
 I/O behind bridge: 0000a000-0000cfff
 Memory behind bridge: dfe00000-dfefffff
 Prefetchable memory behind bridge: cfd00000-dfcfffff
 BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-

0000:00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS963 [MuTIOL Media IO] (rev 25)
 Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 0

0000:00:02.1 SMBus: Silicon Integrated Systems [SiS] SiS961/2 SMBus Controller
 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Interrupt: pin B routed to IRQ 0
 Region 4: I/O ports at 0c00 [size=32]

0000:00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (prog-if 80 [Master])
 Subsystem: Fujitsu Siemens Computer GmbH: Unknown device 1055
 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 128
 Region 4: I/O ports at ffa0 [size=16]

0000:00:02.6 Modem: Silicon Integrated Systems [SiS] AC'97 Modem Controller (rev a0) (prog-if 00 [Generic])
 Subsystem: Fujitsu Siemens Computer GmbH: Unknown device 1055
 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Interrupt: pin C routed to IRQ 177
 Region 0: I/O ports at e000 [size=256]
 Region 1: I/O ports at dc00 [size=128]
 Capabilities: [48] Power Management version 2
  Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] Sound Controller (rev a0)
 Subsystem: Fujitsu Siemens Computer GmbH: Unknown device 1055
 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 64 (13000ns min, 2750ns max)
 Interrupt: pin C routed to IRQ 177
 Region 0: I/O ports at e400 [size=256]
 Region 1: I/O ports at ec00 [size=128]
 Capabilities: [48] Power Management version 2
  Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 0f) (prog-if 10 [OHCI])
 Subsystem: Fujitsu Siemens Computer GmbH: Unknown device 1055
 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
 Latency: 64 (20000ns max), Cache Line Size: 0x08 (32 bytes)
 Interrupt: pin A routed to IRQ 193
 Region 0: Memory at dfff7000 (32-bit, non-prefetchable) [size=4K]

0000:00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 0f) (prog-if 10 [OHCI])
 Subsystem: Fujitsu Siemens Computer GmbH: Unknown device 1055
 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
 Latency: 64 (20000ns max), Cache Line Size: 0x08 (32 bytes)
 Interrupt: pin B routed to IRQ 201
 Region 0: Memory at dfffc000 (32-bit, non-prefetchable) [size=4K]

0000:00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller (prog-if 20 [EHCI])
 Subsystem: Fujitsu Siemens Computer GmbH: Unknown device 1055
 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 64 (20000ns max)
 Interrupt: pin D routed to IRQ 185
 Region 0: Memory at dfffd000 (32-bit, non-prefetchable) [size=4K]
 Capabilities: [50] Power Management version 2
  Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI Fast Ethernet (rev 91)
 Subsystem: Fujitsu Siemens Computer GmbH: Unknown device 1055
 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 64 (13000ns min, 2750ns max)
 Interrupt: pin A routed to IRQ 209
 Region 0: I/O ports at e800 [size=256]
 Region 1: Memory at dfffe000 (32-bit, non-prefetchable) [size=4K]
 Expansion ROM at dffc0000 [disabled] [size=128K]
 Capabilities: [40] Power Management version 2
  Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:08.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 02)
 Subsystem: Fujitsu Siemens Computer GmbH: Unknown device 1055
 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 168, Cache Line Size: 0x08 (32 bytes)
 Interrupt: pin A routed to IRQ 169
 Region 0: Memory at 54000000 (32-bit, non-prefetchable) [size=4K]
 Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
 Memory window 0: 50000000-51fff000 (prefetchable)
 Memory window 1: 52000000-53fff000
 I/O window 0: 00001000-000010ff
 I/O window 1: 00001400-000014ff
 BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
 16-bit legacy interface ports at 0001

0000:00:09.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
 Subsystem: Fujitsu Siemens Computer GmbH: Unknown device 1055
 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 64 (500ns min, 1000ns max), Cache Line Size: 0x08 (32 bytes)
 Interrupt: pin A routed to IRQ 177
 Region 0: Memory at dffff800 (32-bit, non-prefetchable) [size=2K]
 Region 1: Memory at dfff8000 (32-bit, non-prefetchable) [size=16K]
 Capabilities: [44] Power Management version 2
  Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME+

0000:01:00.0 VGA compatible controller: ATI Technologies Inc M9+ 5C61 [Radeon Mobility 9200 (AGP)] (rev 01) (prog-if 00 [VGA])
 Subsystem: Fujitsu Siemens Computer GmbH: Unknown device 1055
 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 64 (2000ns min), Cache Line Size: 0x08 (32 bytes)
 Interrupt: pin A routed to IRQ 217
 Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
 Region 1: I/O ports at c000 [size=256]
 Region 2: Memory at dfef0000 (32-bit, non-prefetchable) [size=64K]
 Expansion ROM at dfec0000 [disabled] [size=128K]
 Capabilities: [58] AGP version 3.0
  Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
  Command: RQ=32 ArqSz=2 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
 Capabilities: [50] Power Management version 2
  Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:02:00.0 Network controller: Texas Instruments ACX 111 54Mbps Wireless Interface
 Subsystem: Texas Instruments: Unknown device 9067
 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 64
 Interrupt: pin A routed to IRQ 169
 Region 0: Memory at 52020000 (32-bit, non-prefetchable) [size=8K]
 Region 1: Memory at 52000000 (32-bit, non-prefetchable) [size=128K]
 Capabilities: [40] Power Management version 2
  Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME-

lspci -vvn:

0000:00:00.0 0600: 1039:0648 (rev 11)
 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
 Latency: 32
 Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=64M]
 Capabilities: [c0] AGP version 3.5
  Status: RQ=32 Iso- ArqSz=2 Cal=3 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
  Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4

0000:00:01.0 0604: 1039:0003
 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 64
 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
 I/O behind bridge: 0000a000-0000cfff
 Memory behind bridge: dfe00000-dfefffff
 Prefetchable memory behind bridge: cfd00000-dfcfffff
 BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-

0000:00:02.0 0601: 1039:0963 (rev 25)
 Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 0

0000:00:02.1 0c05: 1039:0016
 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Interrupt: pin B routed to IRQ 0
 Region 4: I/O ports at 0c00 [size=32]

0000:00:02.5 0101: 1039:5513 (prog-if 80 [Master])
 Subsystem: 1734:1055
 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 128
 Region 4: I/O ports at ffa0 [size=16]

0000:00:02.6 0703: 1039:7013 (rev a0)
 Subsystem: 1734:1055
 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Interrupt: pin C routed to IRQ 177
 Region 0: I/O ports at e000 [size=256]
 Region 1: I/O ports at dc00 [size=128]
 Capabilities: [48] Power Management version 2
  Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:02.7 0401: 1039:7012 (rev a0)
 Subsystem: 1734:1055
 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 64 (13000ns min, 2750ns max)
 Interrupt: pin C routed to IRQ 177
 Region 0: I/O ports at e400 [size=256]
 Region 1: I/O ports at ec00 [size=128]
 Capabilities: [48] Power Management version 2
  Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:03.0 0c03: 1039:7001 (rev 0f) (prog-if 10)
 Subsystem: 1734:1055
 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
 Latency: 64 (20000ns max), Cache Line Size: 0x08 (32 bytes)
 Interrupt: pin A routed to IRQ 193
 Region 0: Memory at dfff7000 (32-bit, non-prefetchable) [size=4K]

0000:00:03.1 0c03: 1039:7001 (rev 0f) (prog-if 10)
 Subsystem: 1734:1055
 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
 Latency: 64 (20000ns max), Cache Line Size: 0x08 (32 bytes)
 Interrupt: pin B routed to IRQ 201
 Region 0: Memory at dfffc000 (32-bit, non-prefetchable) [size=4K]

0000:00:03.3 0c03: 1039:7002 (prog-if 20)
 Subsystem: 1734:1055
 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 64 (20000ns max)
 Interrupt: pin D routed to IRQ 185
 Region 0: Memory at dfffd000 (32-bit, non-prefetchable) [size=4K]
 Capabilities: [50] Power Management version 2
  Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:04.0 0200: 1039:0900 (rev 91)
 Subsystem: 1734:1055
 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 64 (13000ns min, 2750ns max)
 Interrupt: pin A routed to IRQ 209
 Region 0: I/O ports at e800 [size=256]
 Region 1: Memory at dfffe000 (32-bit, non-prefetchable) [size=4K]
 Expansion ROM at dffc0000 [disabled] [size=128K]
 Capabilities: [40] Power Management version 2
  Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:08.0 0607: 104c:ac50 (rev 02)
 Subsystem: 1734:1055
 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 168, Cache Line Size: 0x08 (32 bytes)
 Interrupt: pin A routed to IRQ 169
 Region 0: Memory at 54000000 (32-bit, non-prefetchable) [size=4K]
 Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
 Memory window 0: 50000000-51fff000 (prefetchable)
 Memory window 1: 52000000-53fff000
 I/O window 0: 00001000-000010ff
 I/O window 1: 00001400-000014ff
 BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
 16-bit legacy interface ports at 0001

0000:00:09.0 0c00: 104c:8023 (prog-if 10)
 Subsystem: 1734:1055
 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 64 (500ns min, 1000ns max), Cache Line Size: 0x08 (32 bytes)
 Interrupt: pin A routed to IRQ 177
 Region 0: Memory at dffff800 (32-bit, non-prefetchable) [size=2K]
 Region 1: Memory at dfff8000 (32-bit, non-prefetchable) [size=16K]
 Capabilities: [44] Power Management version 2
  Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME+

0000:01:00.0 0300: 1002:5c61 (rev 01)
 Subsystem: 1734:1055
 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 64 (2000ns min), Cache Line Size: 0x08 (32 bytes)
 Interrupt: pin A routed to IRQ 217
 Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
 Region 1: I/O ports at c000 [size=256]
 Region 2: Memory at dfef0000 (32-bit, non-prefetchable) [size=64K]
 Expansion ROM at dfec0000 [disabled] [size=128K]
 Capabilities: [58] AGP version 3.0
  Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
  Command: RQ=32 ArqSz=2 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
 Capabilities: [50] Power Management version 2
  Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:02:00.0 0280: 104c:9066
 Subsystem: 104c:9067
 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 64
 Interrupt: pin A routed to IRQ 169
 Region 0: Memory at 52020000 (32-bit, non-prefetchable) [size=8K]
 Region 1: Memory at 52000000 (32-bit, non-prefetchable) [size=128K]
 Capabilities: [40] Power Management version 2
  Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME-

lsusb:

Bus 003 Device 002: ID 045e:0047 Microsoft Corp. IntelliMouse Explorer 3.0
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 002: ID 0d62:001c Darfon Electronics Corp.
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000

Ben Collins (ben-collins)
Changed in linux-meta:
status: Unconfirmed → Fix Committed
Revision history for this message
McPolu (mcpolu) wrote :

Today I upgraded to kernel 2.6.15-19 and it tries to load incorrect firmware again. Worst than that, firmware version 1.2.1.34 has been removed.

Revision history for this message
Ben Collins (ben-collins) wrote :

That firmware is there for me. Are you sure you have the updated linux-restricted-modules package installed?

Revision history for this message
McPolu (mcpolu) wrote : Fixed :)

Today I upgraded to kernel 2.6.15-20 and it works. It loads the rigth firmware now :D

I think we should leave this defect still open. When you release a new .iso file including last changes, I will do a clean install and I will test it again.

Thank you very much.

Revision history for this message
Dennis Kaarsemaker (dennis) wrote : Re: [Bug 35703] Fixed :)

 status FixReleased

The new kernel will be on the new daily isos :)

Dennis Kaarsemaker (dennis-merged)
Changed in linux-source-2.6.15:
status: Fix Committed → Fix Released
Revision history for this message
McPolu (mcpolu) wrote :

This is a regressive defect in kernel-25. It was working in kernel -23 but -25 tries to load incorrect firmware again.

To post a comment you must log in.
This report contains Public information  
Everyone can see this information.
Subscribing...

Other bug subscribers

Remote bug watches

Bug watches keep track of this bug in other bug trackers.