merlin@merlin:~$ dmesg [ 0.000000] Linux version 2.6.20-8-generic (root@yellow) (gcc version 4.1.2 20070129 (prerelease) (Ubuntu 4.1.1-31ubuntu2)) #2 SMP Tue Feb 13 01:14:41 UTC 2007 (Ubuntu 2.6.20-8.14-generic) [ 0.000000] Command line: root=UUID=d12f4173-ebf8-468e-b9bb-05f2a9a815f0 ro quiet splash [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000007ff40000 (usable) [ 0.000000] BIOS-e820: 000000007ff40000 - 000000007ff50000 (ACPI data) [ 0.000000] BIOS-e820: 000000007ff50000 - 0000000080000000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 3200 used [ 0.000000] Entering add_active_range(0, 256, 524096) 1 entries of 3200 used [ 0.000000] end_pfn_map = 1048576 [ 0.000000] DMI 2.3 present. [ 0.000000] ACPI: RSDP (v000 MSI ) @ 0x00000000000f83c0 [ 0.000000] ACPI: RSDT (v001 MSI 1029 0x11022005 MSFT 0x00000097) @ 0x000000007ff40000 [ 0.000000] ACPI: FADT (v002 MSI 1029 0x11022005 MSFT 0x00000097) @ 0x000000007ff40200 [ 0.000000] ACPI: MADT (v001 MSI OEMAPIC 0x11022005 MSFT 0x00000097) @ 0x000000007ff40300 [ 0.000000] ACPI: WDRT (v001 MSI MSI_OEM 0x11022005 MSFT 0x00000097) @ 0x000000007ff40360 [ 0.000000] ACPI: MCFG (v001 MSI OEMMCFG 0x11022005 MSFT 0x00000097) @ 0x000000007ff403b0 [ 0.000000] ACPI: SSDT (v001 OEM_ID OEMTBLID 0x00000001 INTL 0x02002026) @ 0x000000007ff434d0 [ 0.000000] ACPI: OEMB (v001 MSI MSI_OEM 0x11022005 MSFT 0x00000097) @ 0x000000007ff50040 [ 0.000000] ACPI: DSDT (v001 MSI 1029 0x11022005 INTL 0x02002026) @ 0x0000000000000000 [ 0.000000] Scanning NUMA topology in Northbridge 24 [ 0.000000] Number of nodes 1 [ 0.000000] Node 0 MemBase 0000000000000000 Limit 000000007ff40000 [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 3200 used [ 0.000000] Entering add_active_range(0, 256, 524096) 1 entries of 3200 used [ 0.000000] NUMA: Using 63 for the hash shift. [ 0.000000] Using node hash shift of 63 [ 0.000000] Bootmem setup node 0 0000000000000000-000000007ff40000 [ 0.000000] No mptable found. [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] DMA32 4096 -> 1048576 [ 0.000000] Normal 1048576 -> 1048576 [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0 -> 159 [ 0.000000] 0: 256 -> 524096 [ 0.000000] On node 0 totalpages: 523999 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 1072 pages reserved [ 0.000000] DMA zone: 2871 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 7109 pages used for memmap [ 0.000000] DMA32 zone: 512891 pages, LIFO batch:31 [ 0.000000] Normal zone: 0 pages used for memmap [ 0.000000] ATI board detected. Disabling timer routing over 8254. [ 0.000000] ACPI: PM-Timer IO Port: 0x4008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] Processor #0 (Bootup-CPU) [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] Setting APIC routing to physical flat [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Nosave address range: 000000000009f000 - 00000000000a0000 [ 0.000000] Nosave address range: 00000000000a0000 - 00000000000e4000 [ 0.000000] Nosave address range: 00000000000e4000 - 0000000000100000 [ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:60000000) [ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs [ 0.000000] PERCPU: Allocating 34048 bytes of per cpu data [ 0.000000] Built 1 zonelists. Total pages: 515762 [ 0.000000] Kernel command line: root=UUID=d12f4173-ebf8-468e-b9bb-05f2a9a815f0 ro quiet splash [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 12.898320] Console: colour VGA+ 80x25 [ 12.899812] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 12.902037] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 12.902244] Checking aperture... [ 12.902248] CPU 0: aperture @ ec12000000 size 32 MB [ 12.902250] Aperture too small (32 MB) [ 12.914078] No AGP bridge found [ 12.937515] Memory: 2053108k/2096384k available (2196k kernel code, 42888k reserved, 1138k data, 300k init) [ 13.014862] Calibrating delay using timer specific routine.. 3983.75 BogoMIPS (lpj=7967505) [ 13.014919] Security Framework v1.0.0 initialized [ 13.014926] SELinux: Disabled at boot. [ 13.014949] Mount-cache hash table entries: 256 [ 13.015091] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 13.015094] CPU: L2 Cache: 1024K (64 bytes/line) [ 13.015096] CPU 0/0 -> Node 0 [ 13.015114] SMP alternatives: switching to UP code [ 13.015338] Freeing SMP alternatives: 28k freed [ 13.015350] ACPI: Core revision 20060707 [ 13.060253] ..MP-BIOS bug: 8254 timer not connected to IO-APIC [ 13.100300] Using local APIC timer interrupts. [ 13.150498] result 12436985 [ 13.150499] Detected 12.436 MHz APIC timer. [ 13.150749] Brought up 1 CPUs [ 13.150788] testing NMI watchdog ... OK. [ 13.190789] time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer. [ 13.190791] time.c: Detected 1989.915 MHz processor. [ 13.191058] NET: Registered protocol family 16 [ 13.191140] ACPI: bus type pci registered [ 13.194445] PCI: Using MMCONFIG at e0000000 [ 13.194487] PCI: No mmconfig possible on device 00:18 [ 13.198479] ACPI: Interpreter enabled [ 13.198482] ACPI: Using IOAPIC for interrupt routing [ 13.198788] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 13.198793] PCI: Probing PCI hardware (bus 00) [ 13.199632] Boot video device is 0000:01:00.0 [ 13.200071] PCI: Transparent bridge - 0000:00:14.4 [ 13.200183] PCI: Bus #04 (-#07) is hidden behind transparent bridge #02 (-#04) (try 'pci=assign-busses') [ 13.200185] Please report the result to linux-kernel to fix this permanently [ 13.200204] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 13.212352] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.POP2._PRT] [ 13.213776] ACPI: PCI Interrupt Link [LNKA] (IRQs *5 6 7 10 11 12 14 15) [ 13.213982] ACPI: PCI Interrupt Link [LNKB] (IRQs *5 6 7 10 11 12 14 15) [ 13.214184] ACPI: PCI Interrupt Link [LNKC] (IRQs 5 6 7 *10 11 12 14 15) [ 13.214388] ACPI: PCI Interrupt Link [LNKD] (IRQs 5 6 7 10 *11 12 14 15) [ 13.214595] ACPI: PCI Interrupt Link [LNKE] (IRQs 5 6 *7 10 11 12 14 15) [ 13.214805] ACPI: PCI Interrupt Link [LNKF] (IRQs 5 6 7 10 11 12 14 15) *0, disabled. [ 13.215011] ACPI: PCI Interrupt Link [LNKG] (IRQs 5 6 7 10 11 12 14 15) *0, disabled. [ 13.215216] ACPI: PCI Interrupt Link [LNKH] (IRQs 5 6 7 10 11 12 14 15) *0, disabled. [ 13.215312] Linux Plug and Play Support v0.97 (c) Adam Belay [ 13.215322] pnp: PnP ACPI init [ 13.216789] pnp: PnP ACPI: found 11 devices [ 13.216832] PCI: Using ACPI for IRQ routing [ 13.216834] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 13.217642] PCI: Bridge: 0000:00:02.0 [ 13.217645] IO window: d000-dfff [ 13.217647] MEM window: fbe00000-fbefffff [ 13.217650] PREFETCH window: f0000000-faffffff [ 13.217664] PCI: Bus 3, cardbus bridge: 0000:02:04.0 [ 13.217667] IO window: 0000e000-0000e0ff [ 13.217668] IO window: 0000e400-0000e4ff [ 13.217671] PREFETCH window: 88000000-8bffffff [ 13.217673] MEM window: 94000000-97ffffff [ 13.217675] PCI: Bus 4, cardbus bridge: 0000:02:04.1 [ 13.217677] IO window: 0000ec00-0000ecff [ 13.217679] IO window: 00001000-000010ff [ 13.217681] PREFETCH window: 8c000000-8fffffff [ 13.217683] MEM window: 98000000-9bffffff [ 13.217685] PCI: Bridge: 0000:00:14.4 [ 13.217691] IO window: e000-efff [ 13.217693] MEM window: fbf00000-fbffffff [ 13.217696] PREFETCH window: 88000000-91ffffff [ 13.217703] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 13.217727] ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 19 (level, low) -> IRQ 19 [ 13.217746] ACPI: PCI Interrupt 0000:02:04.1[B] -> GSI 20 (level, low) -> IRQ 20 [ 13.217819] NET: Registered protocol family 2 [ 13.246667] IP route cache hash table entries: 65536 (order: 7, 524288 bytes) [ 13.247085] TCP established hash table entries: 262144 (order: 10, 4194304 bytes) [ 13.250057] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 13.250819] TCP: Hash tables configured (established 262144 bind 65536) [ 13.250822] TCP reno registered [ 13.262717] checking if image is initramfs... it is [ 13.811115] Freeing initrd memory: 6705k freed [ 13.816588] audit: initializing netlink socket (disabled) [ 13.816600] audit(1171409309.840:1): initialized [ 13.816727] VFS: Disk quotas dquot_6.5.1 [ 13.816742] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 13.816783] io scheduler noop registered [ 13.816785] io scheduler anticipatory registered [ 13.816787] io scheduler deadline registered [ 13.816797] io scheduler cfq registered (default) [ 13.816979] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 13.816994] assign_interrupt_mode Found MSI capability [ 13.817020] Allocate Port Service[0000:00:02.0:pcie00] [ 13.817049] Allocate Port Service[0000:00:02.0:pcie01] [ 13.817143] Evaluate _OSC Set fails. Status = 0x0005 [ 13.817148] Evaluate _OSC Set fails. Status = 0x0005 [ 13.817150] aer_init: AER service init fails - Run ACPI _OSC fails [ 13.817154] aer: probe of 0000:00:02.0:pcie01 failed with error 2 [ 13.837899] Real Time Clock Driver v1.12ac [ 13.837957] Linux agpgart interface v0.101 (c) Dave Jones [ 13.837959] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 13.838422] ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> IRQ 17 [ 13.838429] ACPI: PCI interrupt for device 0000:00:14.6 disabled [ 13.838490] mice: PS/2 mouse device common for all mice [ 13.838964] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 13.839097] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 13.839101] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 13.839359] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 [ 13.840366] i8042.c: Detected active multiplexing controller, rev 1.1. [ 13.840447] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 13.840451] serio: i8042 AUX0 port at 0x60,0x64 irq 12 [ 13.840455] serio: i8042 AUX1 port at 0x60,0x64 irq 12 [ 13.840457] serio: i8042 AUX2 port at 0x60,0x64 irq 12 [ 13.840460] serio: i8042 AUX3 port at 0x60,0x64 irq 12 [ 13.840533] TCP cubic registered [ 13.840540] NET: Registered protocol family 1 [ 13.840546] NET: Registered protocol family 8 [ 13.840548] NET: Registered protocol family 20 [ 13.840693] ACPI: (supports S0 S1 S3 S4 S5) [ 13.840739] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 13.840814] Freeing unused kernel memory: 300k freed [ 13.843735] input: AT Translated Set 2 keyboard as /class/input/input0 [ 15.005776] Capability LSM initialized [ 15.033464] ACPI: duty_cycle spans bit 4 [ 15.033482] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) [ 15.038785] ACPI: Thermal Zone [THRM] (33 C) [ 15.438716] usbcore: registered new interface driver usbfs [ 15.438737] usbcore: registered new interface driver hub [ 15.438757] usbcore: registered new device driver usb [ 15.439381] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver [ 15.439410] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19 [ 15.439425] ohci_hcd 0000:00:13.0: OHCI Host Controller [ 15.439586] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1 [ 15.439607] ohci_hcd 0000:00:13.0: irq 19, io mem 0xfbdfd000 [ 15.500308] usb usb1: configuration #1 chosen from 1 choice [ 15.500331] hub 1-0:1.0: USB hub found [ 15.500343] hub 1-0:1.0: 4 ports detected [ 15.575469] 8139too Fast Ethernet driver 0.9.28 [ 15.595528] ieee1394: Initialized config rom entry `ip1394' [ 15.604007] ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19 [ 15.604024] ohci_hcd 0000:00:13.1: OHCI Host Controller [ 15.604046] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2 [ 15.604063] ohci_hcd 0000:00:13.1: irq 19, io mem 0xfbdfe000 [ 15.663974] usb usb2: configuration #1 chosen from 1 choice [ 15.663998] hub 2-0:1.0: USB hub found [ 15.664009] hub 2-0:1.0: 4 ports detected [ 15.768255] ATIIXP: IDE controller at PCI slot 0000:00:14.1 [ 15.768275] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16 [ 15.768285] ATIIXP: chipset revision 0 [ 15.768287] ATIIXP: not 100% native mode: will probe irqs later [ 15.768296] ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:pio [ 15.768310] ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:pio [ 15.768320] Probing IDE interface ide0... [ 15.907524] usb 1-3: new low speed USB device using ohci_hcd and address 2 [ 16.055790] hda: HTE721080G9AT00, ATA DISK drive [ 16.116494] usb 1-3: configuration #1 chosen from 1 choice [ 16.127083] usbcore: registered new interface driver hiddev [ 16.132658] input: Logitech USB Receiver as /class/input/input1 [ 16.132773] input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:13.0-3 [ 16.132784] usbcore: registered new interface driver usbhid [ 16.132787] drivers/usb/input/hid-core.c: v2.6:USB HID core driver [ 16.726964] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 16.727141] Probing IDE interface ide1... [ 17.462163] hdc: HL-DT-ST DVD-RW GWA-4082N, ATAPI CD/DVD-ROM drive [ 17.798258] ide1 at 0x170-0x177,0x376 on irq 15 [ 17.805858] SCSI subsystem initialized [ 17.810576] libata version 2.00 loaded. [ 17.811813] ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 19 [ 17.811828] ehci_hcd 0000:00:13.2: EHCI Host Controller [ 17.811858] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3 [ 17.811913] ehci_hcd 0000:00:13.2: irq 19, io mem 0xfbdff000 [ 17.811925] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 17.811989] usb 1-3: USB disconnect, address 2 [ 17.812222] usb usb3: configuration #1 chosen from 1 choice [ 17.812243] hub 3-0:1.0: USB hub found [ 17.812249] hub 3-0:1.0: 8 ports detected [ 17.820177] hda: max request size: 512KiB [ 17.832879] hda: 156301488 sectors (80026 MB) w/7539KiB Cache, CHS=16383/255/63, UDMA(100) [ 17.834687] hda: cache flushes supported [ 17.834723] hda: hda1 hda2 hda3 < hda5 hda6 hda7 hda8 hda9<6>ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 18 (level, low) -> IRQ 18 [ 17.914057] eth0: RealTek RTL8139 at 0xffffc20000032c00, 00:13:d3:af:42:ea, IRQ 18 [ 17.914060] eth0: Identified 8139 chip type 'RTL-8101' [ 17.915726] ACPI: PCI Interrupt 0000:02:04.2[C] -> GSI 21 (level, low) -> IRQ 21 [ 17.968118] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[21] MMIO=[fbfff000-fbfff7ff] Max Packet=[2048] IR/IT contexts=[4/4] [ 17.975198] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004) [ 17.976868] hda10 hda11 > [ 18.010207] hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) [ 18.010214] Uniform CD-ROM driver Revision: 3.20 [ 18.350336] Attempting manual resume [ 18.405927] EXT3-fs: INFO: recovery required on readonly filesystem. [ 18.405931] EXT3-fs: write access will be enabled during recovery. [ 18.520504] usb 1-3: new low speed USB device using ohci_hcd and address 3 [ 18.729338] usb 1-3: configuration #1 chosen from 1 choice [ 18.737361] input: Logitech USB Receiver as /class/input/input2 [ 18.737381] input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:13.0-3 [ 19.255804] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0010dc0000d92289] [ 26.160533] kjournald starting. Commit interval 5 seconds [ 26.160550] EXT3-fs: hda10: orphan cleanup on readonly fs [ 26.160556] ext3_orphan_cleanup: deleting unreferenced inode 916718 [ 26.179071] ext3_orphan_cleanup: deleting unreferenced inode 916714 [ 26.189902] ext3_orphan_cleanup: deleting unreferenced inode 983741 [ 26.189920] ext3_orphan_cleanup: deleting unreferenced inode 1161763 [ 26.189939] ext3_orphan_cleanup: deleting unreferenced inode 1013836 [ 26.189957] ext3_orphan_cleanup: deleting unreferenced inode 854517 [ 26.196946] ext3_orphan_cleanup: deleting unreferenced inode 859589 [ 26.205916] ext3_orphan_cleanup: deleting unreferenced inode 855919 [ 26.210200] ext3_orphan_cleanup: deleting unreferenced inode 854594 [ 26.221075] ext3_orphan_cleanup: deleting unreferenced inode 855948 [ 26.229564] ext3_orphan_cleanup: deleting unreferenced inode 1097602 [ 26.238412] ext3_orphan_cleanup: deleting unreferenced inode 1097596 [ 26.238424] ext3_orphan_cleanup: deleting unreferenced inode 1097478 [ 26.241314] ext3_orphan_cleanup: deleting unreferenced inode 859854 [ 26.255708] ext3_orphan_cleanup: deleting unreferenced inode 855253 [ 26.264559] ext3_orphan_cleanup: deleting unreferenced inode 855340 [ 26.264569] ext3_orphan_cleanup: deleting unreferenced inode 1013909 [ 26.272643] ext3_orphan_cleanup: deleting unreferenced inode 1013898 [ 26.272654] ext3_orphan_cleanup: deleting unreferenced inode 1063222 [ 26.285346] ext3_orphan_cleanup: deleting unreferenced inode 854854 [ 26.297751] ext3_orphan_cleanup: deleting unreferenced inode 853068 [ 26.306443] ext3_orphan_cleanup: deleting unreferenced inode 1015638 [ 26.306454] ext3_orphan_cleanup: deleting unreferenced inode 856167 [ 26.312850] ext3_orphan_cleanup: deleting unreferenced inode 1504390 [ 26.322192] ext3_orphan_cleanup: deleting unreferenced inode 1504415 [ 26.327677] ext3_orphan_cleanup: deleting unreferenced inode 1553487 [ 26.353988] ext3_orphan_cleanup: deleting unreferenced inode 950758 [ 26.354000] ext3_orphan_cleanup: deleting unreferenced inode 850527 [ 26.367487] ext3_orphan_cleanup: deleting unreferenced inode 850528 [ 26.367499] ext3_orphan_cleanup: deleting unreferenced inode 850529 [ 26.376242] ext3_orphan_cleanup: deleting unreferenced inode 853929 [ 26.381474] ext3_orphan_cleanup: deleting unreferenced inode 1291825 [ 26.381491] EXT3-fs: hda10: 32 orphan inodes deleted [ 26.381493] EXT3-fs: recovery complete. [ 26.607279] EXT3-fs: mounted filesystem with ordered data mode. [ 36.605036] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 36.827014] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 36.865510] Yenta: CardBus bridge found at 0000:02:04.0 [1462:0291] [ 36.991980] Yenta: ISA IRQ mask 0x0cb8, PCI irq 19 [ 36.991986] Socket status: 30000006 [ 36.991989] pcmcia: parent PCI bridge I/O window: 0xe000 - 0xefff [ 36.991993] pcmcia: parent PCI bridge Memory window: 0xfbf00000 - 0xfbffffff [ 36.991996] pcmcia: parent PCI bridge Memory window: 0x88000000 - 0x91ffffff [ 36.992259] Yenta: CardBus bridge found at 0000:02:04.1 [1462:0291] [ 37.119757] Yenta: ISA IRQ mask 0x04b8, PCI irq 20 [ 37.119763] Socket status: 30000006 [ 37.119766] Yenta: Raising subordinate bus# of parent bus (#02) from #04 to #07 [ 37.119771] pcmcia: parent PCI bridge I/O window: 0xe000 - 0xefff [ 37.119775] pcmcia: parent PCI bridge Memory window: 0xfbf00000 - 0xfbffffff [ 37.119778] pcmcia: parent PCI bridge Memory window: 0x88000000 - 0x91ffffff [ 37.180783] input: PC Speaker as /class/input/input3 [ 37.188292] ieee80211_crypt: registered algorithm 'NULL' [ 37.190328] ieee80211: 802.11 data/management/control stack, git-1.1.13 [ 37.190331] ieee80211: Copyright (C) 2004-2005 Intel Corporation [ 37.209288] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.0kmprq [ 37.209292] ipw2200: Copyright(c) 2003-2006 Intel Corporation [ 37.209385] ACPI: PCI Interrupt 0000:02:09.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 37.209417] ipw2200: Detected Intel PRO/Wireless 2915ABG Network Connection [ 37.231483] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device [ 37.656107] ipw2200: Detected geography ZZA (11 802.11bg channels, 13 802.11a channels) [ 37.656249] ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> IRQ 17 [ 37.667057] ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 17 [ 37.851815] input: ImPS/2 Logitech Wheel Mouse as /class/input/input4 [ 38.330986] lp: driver loaded but no devices found [ 38.392509] Adding 2441840k swap on /dev/disk/by-uuid/12e8e16e-dfa2-41c9-9168-b509626b1817. Priority:-1 extents:1 across:2441840k [ 38.634140] EXT3 FS on hda10, internal journal [ 40.346913] kjournald starting. Commit interval 5 seconds [ 40.347187] EXT3 FS on hda11, internal journal [ 40.347191] EXT3-fs: mounted filesystem with ordered data mode. [ 40.372861] kjournald starting. Commit interval 5 seconds [ 40.373136] EXT3 FS on hda2, internal journal [ 40.373140] EXT3-fs: mounted filesystem with ordered data mode. [ 40.387568] kjournald starting. Commit interval 5 seconds [ 40.395715] EXT3 FS on hda5, internal journal [ 40.395719] EXT3-fs: mounted filesystem with ordered data mode. [ 40.429321] kjournald starting. Commit interval 5 seconds [ 40.436288] EXT3 FS on hda6, internal journal [ 40.436292] EXT3-fs: mounted filesystem with ordered data mode. [ 40.463361] kjournald starting. Commit interval 5 seconds [ 40.471627] EXT3 FS on hda7, internal journal [ 40.471631] EXT3-fs: mounted filesystem with ordered data mode. [ 40.473884] kjournald starting. Commit interval 5 seconds [ 40.474152] EXT3 FS on hda8, internal journal [ 40.474156] EXT3-fs: mounted filesystem with ordered data mode. [ 40.476122] kjournald starting. Commit interval 5 seconds [ 40.476385] EXT3 FS on hda9, internal journal [ 40.476389] EXT3-fs: mounted filesystem with ordered data mode. [ 42.555573] vbetool[4197]: segfault at 000000000000362f rip 00000000004247f7 rsp 00007fff5faf23f0 error 4 [ 42.604229] Using specific hotkey driver [ 42.708398] input: Power Button (FF) as /class/input/input5 [ 42.722914] ACPI: Power Button (FF) [PWRF] [ 42.757742] input: Lid Switch as /class/input/input6 [ 42.772167] ACPI: Lid Switch [LID0] [ 42.806931] input: Sleep Button (CM) as /class/input/input7 [ 42.821331] ACPI: Sleep Button (CM) [SLPB] [ 42.856074] input: Power Button (CM) as /class/input/input8 [ 42.870439] ACPI: Power Button (CM) [PWRB] [ 42.878542] No dock devices found. [ 42.899749] ACPI: Battery Slot [BAT1] (battery present) [ 42.908305] ibm_acpi: ec object not found [ 42.941765] ACPI: AC Adapter [ADP1] (on-line) [ 43.108534] powernow-k8: Found 1 AMD Turion(tm) 64 Mobile Technology MT-37 processors (version 2.00.00) [ 43.108626] ACPI: Invalid package argument [ 43.108630] ACPI Exception (acpi_processor-0270): AE_BAD_PARAMETER, Invalid _PSS data [20060707] [ 43.116369] powernow-k8: 0 : fid 0x0 (800 MHz), vid 0x16 [ 43.116371] powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0xe [ 43.116373] powernow-k8: 2 : fid 0xa (1800 MHz), vid 0xc [ 43.116375] powernow-k8: 3 : fid 0xc (2000 MHz), vid 0xa [ 43.117308] powernow-k8: ph2 null fid transition 0xc [ 44.923812] ppdev: user-space parallel port driver [ 46.248857] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [ 46.253094] [fglrx] Maximum main memory to use for locked dma buffers: 1884 MBytes. [ 46.253312] [fglrx] module loaded - fglrx 8.33.6 [Jan 8 2007] on minor 0 [ 46.321882] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 18 (level, low) -> IRQ 18 [ 48.543409] [fglrx] total GART = 130023424 [ 48.543414] [fglrx] free GART = 114032640 [ 48.543417] [fglrx] max single GART = 114032640 [ 48.543419] [fglrx] total LFB = 134086656 [ 48.543421] [fglrx] free LFB = 119697408 [ 48.543423] [fglrx] max single LFB = 119697408 [ 48.543425] [fglrx] total Inv = 0 [ 48.543426] [fglrx] free Inv = 0 [ 48.543428] [fglrx] max single Inv = 0 [ 48.543429] [fglrx] total TIM = 0 [ 54.461364] eth0: link down [ 54.775328] Bluetooth: Core ver 2.11 [ 54.775670] NET: Registered protocol family 31 [ 54.775672] Bluetooth: HCI device and connection manager initialized [ 54.775676] Bluetooth: HCI socket layer initialized [ 54.815953] Bluetooth: L2CAP ver 2.8 [ 54.815957] Bluetooth: L2CAP socket layer initialized [ 54.940586] Bluetooth: RFCOMM socket layer initialized [ 54.940600] Bluetooth: RFCOMM TTY layer initialized [ 54.940602] Bluetooth: RFCOMM ver 1.8 [ 61.253057] NET: Registered protocol family 10 [ 61.253130] lo: Disabled Privacy Extensions [ 61.253173] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 70.464970] eth1: no IPv6 routers present [ 75.485006] [fglrx] total GART = 130023424 [ 75.485011] [fglrx] free GART = 114032640 [ 75.485014] [fglrx] max single GART = 114032640 [ 75.485016] [fglrx] total LFB = 134086656 [ 75.485018] [fglrx] free LFB = 119697408 [ 75.485020] [fglrx] max single LFB = 119697408 [ 75.485022] [fglrx] total Inv = 0 [ 75.485023] [fglrx] free Inv = 0 [ 75.485025] [fglrx] max single Inv = 0 [ 75.485026] [fglrx] total TIM = 0 [ 95.426203] NET: Registered protocol family 17 [ 95.440308] ieee80211_crypt: registered algorithm 'WEP' [ 104.719216] eth1: no IPv6 routers present [ 128.592056] APIC error on CPU0: 00(40) [ 202.658810] usb 1-3: USB disconnect, address 3 [ 203.749957] usb 1-3: new low speed USB device using ohci_hcd and address 4 [ 203.833520] usb 1-3: configuration #1 chosen from 1 choice [ 203.836749] input: Logitech USB Receiver as /class/input/input9 [ 203.836794] input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:13.0-3 [ 238.053209] APIC error on CPU0: 40(40) merlin@merlin:~$