No Sound on Gutsy
Notebook computer: Gateway M4520GZ
Dual booted with Windows XP - sound works fine on XP


After following the instructions in the document: Debugging Sound Problems
still no sound


Here is the output from various commands (per Debugging Sound Problems document):


--------------
Checking sound device assignment:
 cat /proc/asound/cards
 0 [I82801DBICH4   ]: ICH4 - Intel 82801DB-ICH4
                      Intel 82801DB-ICH4 with AD1981B at irq 10

-------------
Checking if more thatn one card listed:

 lsmod | grep snd
snd_intel8x0           34972  1 
snd_ac97_codec        101284  1 snd_intel8x0
ac97_bus                3200  1 snd_ac97_codec
snd_pcm_oss            43008  0 
snd_mixer_oss          17664  1 snd_pcm_oss
snd_pcm                80004  3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_seq_dummy           4740  0 
snd_seq_oss            33152  0 
snd_seq_midi            9600  0 
snd_rawmidi            25728  1 snd_seq_midi
snd_seq_midi_event      8448  2 snd_seq_oss,snd_seq_midi
snd_seq                53360  6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer              24324  2 snd_pcm,snd_seq
snd_seq_device          9228  5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
snd                    54788  12 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore               8800  1 snd
snd_page_alloc         11400  2 snd_intel8x0,snd_pcm

--------------
Kernel Version (Gutsy regular release desktop install i386):
uname -a
Linux gateway 2.6.22-14-generic #1 SMP Sun Oct 14 23:05:12 GMT 2007 i686 GNU/Linux

--------------
List of sound cards configured by alsa:
 aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: I82801DBICH4 [Intel 82801DB-ICH4], device 0: Intel ICH [Intel 82801DB-ICH4]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 0: I82801DBICH4 [Intel 82801DB-ICH4], device 4: Intel ICH - IEC958 [Intel 82801DB-ICH4 - IEC958]
  Subdevices: 1/1
  Subdevice #0: subdevice #0

--------------
what sound card (chip set) you have:

 sudo lspci -vvnn
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller [8086:24c5] (rev 03)
        Subsystem: Rioworks Unknown device [161f:203a]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 10
        Region 0: I/O ports at 1c00 [size=256]
        Region 1: I/O ports at 18c0 [size=64]
        Region 2: Memory at e0100c00 (32-bit, non-prefetchable) [size=512]
        Region 3: Memory at e0100800 (32-bit, non-prefetchable) [size=256]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

lspnp -v
lspnp: /proc/bus/pnp not available
(after I installed pnpbios-tools and rebooted)

--------------
List codecs involved:

 tail -2 /proc/asound/oss/sndstat
Mixers:
0: Analog Devices AD1981B

--------------
amixer output:
amixer
Simple mixer control 'Master',0
  Capabilities: pvolume pswitch
  Playback channels: Front Left - Front Right
  Limits: Playback 0 - 31
  Mono:
  Front Left: Playback 31 [100%] [0.00dB] [on]
  Front Right: Playback 31 [100%] [0.00dB] [on]
Simple mixer control 'Master Mono',0
  Capabilities: pvolume pvolume-joined pswitch pswitch-joined
  Playback channels: Mono
  Limits: Playback 0 - 31
  Mono: Playback 31 [100%] [0.00dB] [on]
Simple mixer control 'Headphone',0
  Capabilities: pvolume pswitch
  Playback channels: Front Left - Front Right
  Limits: Playback 0 - 31
  Mono:
  Front Left: Playback 31 [100%] [0.00dB] [on]
  Front Right: Playback 31 [100%] [0.00dB] [on]
Simple mixer control 'Headphone Jack Sense',0
  Capabilities: pswitch pswitch-joined
  Playback channels: Mono
  Mono: Playback [on]
Simple mixer control 'PCM',0
  Capabilities: pvolume pswitch
  Playback channels: Front Left - Front Right
  Limits: Playback 0 - 31
  Mono:
  Front Left: Playback 31 [100%] [12.00dB] [on]
  Front Right: Playback 31 [100%] [12.00dB] [on]
Simple mixer control 'Line',0
  Capabilities: pvolume pswitch cswitch cswitch-exclusive
  Capture exclusive group: 0
  Playback channels: Front Left - Front Right
  Capture channels: Front Left - Front Right
  Limits: Playback 0 - 31
  Front Left: Playback 31 [100%] [12.00dB] [on] Capture [off]
  Front Right: Playback 31 [100%] [12.00dB] [on] Capture [off]
Simple mixer control 'Line Jack Sense',0
  Capabilities: pswitch pswitch-joined
  Playback channels: Mono
  Mono: Playback [on]
Simple mixer control 'CD',0
  Capabilities: pvolume pswitch cswitch cswitch-exclusive
  Capture exclusive group: 0
  Playback channels: Front Left - Front Right
  Capture channels: Front Left - Front Right
  Limits: Playback 0 - 31
  Front Left: Playback 31 [100%] [12.00dB] [on] Capture [off]
  Front Right: Playback 31 [100%] [12.00dB] [on] Capture [off]
Simple mixer control 'Mic',0
  Capabilities: pvolume pvolume-joined pswitch pswitch-joined cswitch cswitch-exclusive
  Capture exclusive group: 0
  Playback channels: Mono
  Capture channels: Front Left - Front Right
  Limits: Playback 0 - 31
  Mono: Playback 29 [94%] [9.00dB] [on]
  Front Left: Capture [off]
  Front Right: Capture [off]
Simple mixer control 'Mic Boost (+20dB)',0
  Capabilities: pswitch pswitch-joined
  Playback channels: Mono
  Mono: Playback [on]
Simple mixer control 'Mic Select',0
  Capabilities: enum
  Items: 'Mic1' 'Mic2'
  Item0: 'Mic1'
Simple mixer control 'Video',0
  Capabilities: cswitch cswitch-exclusive
  Capture exclusive group: 0
  Capture channels: Front Left - Front Right
  Front Left: Capture [off]
  Front Right: Capture [off]
Simple mixer control 'Phone',0
  Capabilities: pvolume pvolume-joined pswitch pswitch-joined cswitch cswitch-exclusive
  Capture exclusive group: 0
  Playback channels: Mono
  Capture channels: Front Left - Front Right
  Limits: Playback 0 - 31
  Mono: Playback 31 [100%] [12.00dB] [on]
  Front Left: Capture [off]
  Front Right: Capture [off]
Simple mixer control 'IEC958',0
  Capabilities: pswitch pswitch-joined
  Playback channels: Mono
  Mono: Playback [on]
Simple mixer control 'IEC958 Playback AC97-SPSA',0
  Capabilities: volume volume-joined
  Playback channels: Mono
  Capture channels: Mono
  Limits: 0 - 3
  Mono: 3 [100%]
Simple mixer control 'IEC958 Playback Source',0
  Capabilities: enum
  Items: 'AC-Link' 'A/D Converter'
  Item0: 'AC-Link'
Simple mixer control 'Aux',0
  Capabilities: pvolume pswitch cswitch cswitch-exclusive
  Capture exclusive group: 0
  Playback channels: Front Left - Front Right
  Capture channels: Front Left - Front Right
  Limits: Playback 0 - 31
  Front Left: Playback 31 [100%] [12.00dB] [on] Capture [off]
  Front Right: Playback 31 [100%] [12.00dB] [on] Capture [off]
Simple mixer control 'Mono Output Select',0
  Capabilities: enum
  Items: 'Mix' 'Mic'
  Item0: 'Mic'
Simple mixer control 'Capture',0
  Capabilities: cvolume cswitch
  Capture channels: Front Left - Front Right
  Limits: Capture 0 - 15
  Front Left: Capture 14 [93%] [21.00dB] [on]
  Front Right: Capture 14 [93%] [21.00dB] [on]
Simple mixer control 'Mix',0
  Capabilities: cswitch cswitch-exclusive
  Capture exclusive group: 0
  Capture channels: Front Left - Front Right
  Front Left: Capture [off]
  Front Right: Capture [off]
Simple mixer control 'Mix Mono',0
  Capabilities: cswitch cswitch-exclusive
  Capture exclusive group: 0
  Capture channels: Front Left - Front Right
  Front Left: Capture [on]
  Front Right: Capture [on]
Simple mixer control 'External Amplifier',0
  Capabilities: pswitch pswitch-joined
  Playback channels: Mono
  Mono: Playback [on]
Simple mixer control 'Stereo Mic',0
  Capabilities: pswitch pswitch-joined
  Playback channels: Mono
  Mono: Playback [off]

--------------
Names of available sound cards:
 asoundconf list
Names of available sound cards:
I82801DBICH4

--------------
List the enumerated sound devices on your system:
cat /etc/asound.conf ~/.asoundrc*
cat: /etc/asound.conf: No such file or directory
cat: /home/gf/.asoundrc*: No such file or directory

I note there is no asound.conf file in the /etc directory.
A file search found no asound.conf file on the system.
There is, however, a asound.conf_configuresoundproperly file in the usr/share/ununtu-docs/ubuntu/sample.

--------------
Resources:

cat /proc/interrupts
           CPU0       
  0:     167698    XT-PIC-XT        timer
  1:       2995    XT-PIC-XT        i8042
  2:          0    XT-PIC-XT        cascade
  3:          4    XT-PIC-XT        ehci_hcd:usb4
  5:      38603    XT-PIC-XT        uhci_hcd:usb1
  8:          3    XT-PIC-XT        rtc
  9:       4604    XT-PIC-XT        acpi
 10:      24987    XT-PIC-XT        uhci_hcd:usb3, ohci1394, yenta, ipw2200, Intel 82801DB-ICH4, eth0
 11:      13903    XT-PIC-XT        uhci_hcd:usb2, yenta
 12:     156461    XT-PIC-XT        i8042
 14:       9624    XT-PIC-XT        libata
 15:      22775    XT-PIC-XT        libata
NMI:          0 
LOC:          0 
ERR:          0
MIS:          0










--------------
dmesg

dmesg
[    0.000000] Linux version 2.6.22-14-generic (buildd@palmer) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun Oct 14 23:05:12 GMT 2007 (Ubuntu 2.6.22-14.46-generic)
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[    0.000000]  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000ce000 - 00000000000d0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000001dee0000 (usable)
[    0.000000]  BIOS-e820: 000000001dee0000 - 000000001deeb000 (ACPI data)
[    0.000000]  BIOS-e820: 000000001deeb000 - 000000001df00000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000001df00000 - 0000000020000000 (reserved)
[    0.000000]  BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
[    0.000000]  BIOS-e820: 00000000fffffc00 - 0000000100000000 (reserved)
[    0.000000] 0MB HIGHMEM available.
[    0.000000] 478MB LOWMEM available.
[    0.000000] Entering add_active_range(0, 0, 122592) 0 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->   122592
[    0.000000]   HighMem    122592 ->   122592
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->   122592
[    0.000000] On node 0 totalpages: 122592
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4064 pages, LIFO batch:0
[    0.000000]   Normal zone: 925 pages used for memmap
[    0.000000]   Normal zone: 117571 pages, LIFO batch:31
[    0.000000]   HighMem zone: 0 pages used for memmap
[    0.000000] DMI present.
[    0.000000] ACPI: RSDP signature @ 0xC00F7780 checksum 0
[    0.000000] ACPI: RSDP 000F7780, 0014 (r0 PTLTD )
[    0.000000] ACPI: RSDT 1DEE69EE, 0034 (r1 PTLTD  ManiaBan  6040000  LTP        0)
[    0.000000] ACPI: FACP 1DEEAEC4, 0074 (r1 INTEL  MONTARA   6040000 PTL        50)
[    0.000000] ACPI: DSDT 1DEE6F2F, 3F95 (r1 INTEL  MONTARAG  6040000 MSFT  100000E)
[    0.000000] ACPI: FACS 1DEFBFC0, 0040
[    0.000000] ACPI: BOOT 1DEEAFD8, 0028 (r1 PTLTD  $SBFTBL$  6040000  LTP        1)
[    0.000000] ACPI: SSDT 1DEE6E1E, 0109 (r1 INTEL  CPU0CST         1 INTL 20030224)
[    0.000000] ACPI: SSDT 1DEE6A22, 0270 (r1  INTEL  EISTRef     2000 INTL 20030224)
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:df800000)
[    0.000000] Built 1 zonelists.  Total pages: 121635
[    0.000000] Kernel command line: root=UUID=324f8b73-2f04-41a4-9150-04e6ec82c996 ro quiet splash vga=788
[    0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[    0.000000] mapped APIC to ffffd000 (013cd000)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[    0.000000] Detected 1495.203 MHz processor.
[    6.521819] Console: colour dummy device 80x25
[    6.521992] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    6.522236] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    6.540384] Memory: 474636k/490368k available (2015k kernel code, 15184k reserved, 916k data, 364k init, 0k highmem)
[    6.540396] virtual kernel memory layout:
[    6.540398]     fixmap  : 0xfff4d000 - 0xfffff000   ( 712 kB)
[    6.540400]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    6.540401]     vmalloc : 0xde800000 - 0xff7fe000   ( 527 MB)
[    6.540403]     lowmem  : 0xc0000000 - 0xddee0000   ( 478 MB)
[    6.540404]       .init : 0xc03e3000 - 0xc043e000   ( 364 kB)
[    6.540406]       .data : 0xc02f7d26 - 0xc03dce84   ( 916 kB)
[    6.540408]       .text : 0xc0100000 - 0xc02f7d26   (2015 kB)
[    6.540412] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[    6.540459] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[    6.620382] Calibrating delay using timer specific routine.. 2992.39 BogoMIPS (lpj=5984786)
[    6.620412] Security Framework v1.0.0 initialized
[    6.620421] SELinux:  Disabled at boot.
[    6.620439] Mount-cache hash table entries: 512
[    6.620588] CPU: After generic identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000
[    6.620601] CPU: L1 I cache: 32K, L1 D cache: 32K
[    6.620605] CPU: L2 cache: 1024K
[    6.620608] CPU: After all inits, caps: a7e9f9bf 00000000 00000000 00002040 00000180 00000000 00000000
[    6.620619] Compat vDSO mapped to ffffe000.
[    6.620632] Checking 'hlt' instruction... OK.
[    6.636464] SMP alternatives: switching to UP code
[    6.636641] Freeing SMP alternatives: 11k freed
[    6.636931] Early unpacking initramfs... done
[    7.036531] ACPI: Core revision 20070126
[    7.036616] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[    7.038311] ACPI: setting ELCR to 0200 (from 0c28)
[    7.047244] CPU0: Intel(R) Pentium(R) M processor 1500MHz stepping 05
[    7.047252] SMP motherboard not detected.
[    7.047254] Local APIC not detected. Using dummy APIC emulation.
[    7.047293] Brought up 1 CPUs
[    7.047422] Booting paravirtualized kernel on bare hardware
[    7.047493] Time:  6:16:06  Date: 10/08/107
[    7.047519] NET: Registered protocol family 16
[    7.047610] EISA bus registered
[    7.047624] ACPI: bus type pci registered
[    7.048112] PCI: PCI BIOS revision 2.10 entry at 0xfd932, last bus=2
[    7.048115] PCI: Using configuration type 1
[    7.048117] Setting up standard PCI resources
[    7.057328] ACPI: EC: Look up EC in DSDT
[    7.057926] ACPI: EC: GPE=0x1c, ports=0x66, 0x62
[    7.058883] ACPI: Interpreter enabled
[    7.058887] ACPI: (supports S0 S3 S4 S5)
[    7.058905] ACPI: Using PIC for interrupt routing
[    7.062831] ACPI: EC: GPE=0x1c, ports=0x66, 0x62
[    7.062878] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    7.062888] PCI: Probing PCI hardware (bus 00)
[    7.063330] PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
[    7.063334] PCI quirk: region 1180-11bf claimed by ICH4 GPIO
[    7.063731] PCI: Transparent bridge - 0000:00:1e.0
[    7.063854] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    7.064101] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[    7.066813] ACPI: PCI Interrupt Link [LNKA] (IRQs *5)
[    7.066898] ACPI: PCI Interrupt Link [LNKB] (IRQs *10)
[    7.066979] ACPI: PCI Interrupt Link [LNKC] (IRQs *10)
[    7.067060] ACPI: PCI Interrupt Link [LNKD] (IRQs *11)
[    7.067141] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[    7.067227] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[    7.067313] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[    7.067398] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 *3 4 5 6 7 11 12 14 15)
[    7.067491] Linux Plug and Play Support v0.97 (c) Adam Belay
[    7.067507] pnp: PnP ACPI init
[    7.067516] ACPI: bus type pnp registered
[    7.068987] pnp: PnP ACPI: found 8 devices
[    7.068990] ACPI: ACPI bus type pnp unregistered
[    7.068994] PnPBIOS: Disabled by ACPI PNP
[    7.069051] PCI: Using ACPI for IRQ routing
[    7.069055] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[    7.074657] NET: Registered protocol family 8
[    7.074660] NET: Registered protocol family 20
[    7.074724] pnp: 00:04: iomem range 0xfec10000-0xfec1ffff has been reserved
[    7.074734] pnp: 00:04: iomem range 0xe0000000-0xefffffff could not be reserved
[    7.075821] Time: tsc clocksource has been installed.
[    7.105022] PCI: Bus 3, cardbus bridge: 0000:02:07.0
[    7.105025]   IO window: 00003400-000034ff
[    7.105029]   IO window: 00003800-000038ff
[    7.105034]   PREFETCH window: 30000000-33ffffff
[    7.105038]   MEM window: 3c000000-3fffffff
[    7.105042] PCI: Bus 7, cardbus bridge: 0000:02:07.1
[    7.105045]   IO window: 00003c00-00003cff
[    7.105049]   IO window: 00001400-000014ff
[    7.105053]   PREFETCH window: 34000000-37ffffff
[    7.105058]   MEM window: 40000000-43ffffff
[    7.105061] PCI: Bridge: 0000:00:1e.0
[    7.105065]   IO window: 3000-3fff
[    7.105070]   MEM window: e0200000-e02fffff
[    7.105075]   PREFETCH window: 30000000-37ffffff
[    7.105087] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[    7.105245] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[    7.105249] PCI: setting IRQ 11 as level-triggered
[    7.105253] ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
[    7.105260] PCI: Setting latency timer of device 0000:02:07.0 to 64
[    7.105392] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
[    7.105395] PCI: setting IRQ 10 as level-triggered
[    7.105399] ACPI: PCI Interrupt 0000:02:07.1[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
[    7.105405] PCI: Setting latency timer of device 0000:02:07.1 to 64
[    7.105421] NET: Registered protocol family 2
[    7.143776] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    7.143821] TCP established hash table entries: 16384 (order: 5, 196608 bytes)
[    7.144010] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[    7.144134] TCP: Hash tables configured (established 16384 bind 16384)
[    7.144138] TCP reno registered
[    7.155876] checking if image is initramfs... it is
[    7.607194] Switched to high resolution mode on CPU 0
[    7.933062] Freeing initrd memory: 7062k freed
[    7.933238] Simple Boot Flag at 0x36 set to 0x1
[    7.933475] audit: initializing netlink socket (disabled)
[    7.933494] audit(1194502566.036:1): initialized
[    7.935983] VFS: Disk quotas dquot_6.5.1
[    7.936052] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    7.936174] io scheduler noop registered
[    7.936177] io scheduler anticipatory registered
[    7.936179] io scheduler deadline registered
[    7.936203] io scheduler cfq registered (default)
[    7.936223] Boot video device is 0000:00:02.0
[    7.936562] isapnp: Scanning for PnP cards...
[    8.289952] isapnp: No Plug & Play device found
[    8.322942] Real Time Clock Driver v1.12ac
[    8.323057] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[    8.323866] ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
[    8.323876] ACPI: PCI interrupt for device 0000:00:1f.6 disabled
[    8.324493] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[    8.324770] input: Macintosh mouse button emulation as /class/input/input0
[    8.324854] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    8.328401] serio: i8042 KBD port at 0x60,0x64 irq 1
[    8.328408] serio: i8042 AUX port at 0x60,0x64 irq 12
[    8.328592] mice: PS/2 mouse device common for all mice
[    8.328720] EISA: Probing bus 0 at eisa.0
[    8.328730] Cannot allocate resource for EISA slot 1
[    8.328734] Cannot allocate resource for EISA slot 2
[    8.328737] Cannot allocate resource for EISA slot 3
[    8.328758] EISA: Detected 0 cards.
[    8.328885] TCP cubic registered
[    8.328906] NET: Registered protocol family 1
[    8.328940] Using IPI No-Shortcut mode
[    8.329147]   Magic number: 15:982:265
[    8.329179]   hash matches device ttyx7
[    8.329193]   hash matches device ttyua
[    8.329542] Freeing unused kernel memory: 364k freed
[    8.645790] input: AT Translated Set 2 keyboard as /class/input/input1
[    9.540890] AppArmor: AppArmor initialized<5>audit(1194502567.536:2):  type=1505 info="AppArmor initialized" pid=1184
[    9.547735] fuse init (API version 7.8)
[    9.552846] Failure registering capabilities with primary security module.
[    9.576299] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[    9.576307] ACPI: Processor [CPU0] (supports 8 throttling states)
[    9.578290] ACPI: Thermal Zone [THRM] (47 C)
[   10.037863] usbcore: registered new interface driver usbfs
[   10.037890] usbcore: registered new interface driver hub
[   10.037920] usbcore: registered new device driver usb
[   10.039484] USB Universal Host Controller Interface driver v3.0
[   10.039775] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5
[   10.039779] PCI: setting IRQ 5 as level-triggered
[   10.039783] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 5 (level, low) -> IRQ 5
[   10.039796] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[   10.039800] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[   10.040064] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[   10.040088] uhci_hcd 0000:00:1d.0: irq 5, io base 0x00001820
[   10.040230] usb usb1: configuration #1 chosen from 1 choice
[   10.040259] hub 1-0:1.0: USB hub found
[   10.040264] hub 1-0:1.0: 2 ports detected
[   10.126868] SCSI subsystem initialized
[   10.138520] libata version 2.21 loaded.
[   10.143963] ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
[   10.143978] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[   10.143983] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[   10.144010] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[   10.144035] uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001840
[   10.144158] usb usb2: configuration #1 chosen from 1 choice
[   10.144187] hub 2-0:1.0: USB hub found
[   10.144194] hub 2-0:1.0: 2 ports detected
[   10.202947] 8139too Fast Ethernet driver 0.9.28
[   10.248069] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
[   10.248075] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
[   10.248088] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[   10.248093] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[   10.248123] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[   10.248148] uhci_hcd 0000:00:1d.2: irq 10, io base 0x00001860
[   10.248277] usb usb3: configuration #1 chosen from 1 choice
[   10.248307] hub 3-0:1.0: USB hub found
[   10.248314] hub 3-0:1.0: 2 ports detected
[   10.352771] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 3
[   10.352777] PCI: setting IRQ 3 as level-triggered
[   10.352782] ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 3 (level, low) -> IRQ 3
[   10.352798] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[   10.352803] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[   10.352845] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
[   10.352881] ehci_hcd 0000:00:1d.7: debug port 1
[   10.352888] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[   10.352899] ehci_hcd 0000:00:1d.7: irq 3, io mem 0xe0100000
[   10.356784] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   10.356906] usb usb4: configuration #1 chosen from 1 choice
[   10.356939] hub 4-0:1.0: USB hub found
[   10.356947] hub 4-0:1.0: 6 ports detected
[    3.876000] Marking TSC unstable due to: possible TSC halt in C2.
[    3.892000] Time: acpi_pm clocksource has been installed.
[    3.928000] ata_piix 0000:00:1f.1: version 2.11
[    3.928000] PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
[    3.928000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
[    3.928000] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[    3.928000] scsi0 : ata_piix
[    3.928000] scsi1 : ata_piix
[    3.928000] ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00011810 irq 14
[    3.928000] ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x00011818 irq 15
[    4.092000] ata1.00: ATA-5: HITACHI_DK23FA-60, 00M4A0A2, max UDMA/100
[    4.092000] ata1.00: 117210240 sectors, multi 16: LBA 
[    4.100000] ata1.00: configured for UDMA/100
[    4.420000] ata2.00: ATAPI: HL-DT-STCD-RW/DVD DRIVE GCC-4241N, 0P34, max UDMA/33
[    4.456000] usb 2-2: new low speed USB device using uhci_hcd and address 2
[    4.592000] ata2.00: configured for UDMA/33
[    4.592000] scsi 0:0:0:0: Direct-Access     ATA      HITACHI_DK23FA-6 00M4 PQ: 0 ANSI: 5
[    4.596000] scsi 1:0:0:0: CD-ROM            HL-DT-ST RW/DVD GCC-4241N 0P34 PQ: 0 ANSI: 5
[    4.596000] ACPI: PCI Interrupt 0000:02:07.2[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
[    4.656000] usb 2-2: configuration #1 chosen from 1 choice
[    4.668000] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10]  MMIO=[e0201000-e02017ff]  Max Packet=[2048]  IR/IT contexts=[4/4]
[    4.692000] usbcore: registered new interface driver hiddev
[    4.692000] ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
[    4.692000] eth0: RealTek RTL8139 at 0xde858800, 00:03:25:10:6a:9a, IRQ 10
[    4.692000] eth0:  Identified 8139 chip type 'RTL-8101'
[    4.696000] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[    4.696000] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB)
[    4.696000] sd 0:0:0:0: [sda] Write Protect is off
[    4.696000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    4.696000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.696000] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB)
[    4.696000] sd 0:0:0:0: [sda] Write Protect is off
[    4.696000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    4.696000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.696000]  sda:<6>input: HID 04b3:310b as /class/input/input2
[    4.704000] input: USB HID v1.00 Mouse [HID 04b3:310b] on usb-0000:00:1d.1-2
[    4.704000] usbcore: registered new interface driver usbhid
[    4.704000] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[    4.732000]  sda1 sda2 < sda5 sda6 > sda3
[    4.764000] sd 0:0:0:0: [sda] Attached SCSI disk
[    4.768000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    4.768000] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    4.796000] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[    4.796000] Uniform CD-ROM driver Revision: 3.20
[    4.796000] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    5.132000] Attempting manual resume
[    5.132000] swsusp: Resume From Partition 8:6
[    5.132000] PM: Checking swsusp image.
[    5.132000] PM: Resume from disk failed.
[    5.184000] kjournald starting.  Commit interval 5 seconds
[    5.184000] EXT3-fs: mounted filesystem with ordered data mode.
[    5.948000] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00032521350027d2]
[   14.656000] Linux agpgart interface v0.102 (c) Dave Jones
[   14.700000] agpgart: Detected an Intel 855GM Chipset.
[   14.700000] agpgart: Detected 32636K stolen memory.
[   14.708000] agpgart: AGP aperture is 128M @ 0xe8000000
[   15.336000] intel_rng: FWH not detected
[   15.604000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   15.616000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   15.752000] iTCO_vendor_support: vendor-support=0
[   16.076000] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
[   16.276000] Yenta: CardBus bridge found at 0000:02:07.0 [161f:203a]
[   16.396000] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x236eb3, caps: 0x904713/0x10008
[   16.404000] Yenta: ISA IRQ mask 0x0090, PCI irq 11
[   16.404000] Socket status: 30000006
[   16.404000] Yenta: Raising subordinate bus# of parent bus (#02) from #02 to #06
[   16.404000] pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
[   16.404000] cs: IO port probe 0x3000-0x3fff: clean.
[   16.404000] pcmcia: parent PCI bridge Memory window: 0xe0200000 - 0xe02fffff
[   16.404000] pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x37ffffff
[   16.404000] Yenta: CardBus bridge found at 0000:02:07.1 [161f:203a]
[   16.420000] ieee80211_crypt: registered algorithm 'NULL'
[   16.432000] input: SynPS/2 Synaptics TouchPad as /class/input/input3
[   16.436000] iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0x1060)
[   16.436000] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   16.444000] ieee80211: 802.11 data/management/control stack, git-1.1.13
[   16.444000] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[   16.528000] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.0kmprq
[   16.528000] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[   16.532000] Yenta: ISA IRQ mask 0x0090, PCI irq 10
[   16.532000] Socket status: 30000006
[   16.532000] Yenta: Raising subordinate bus# of parent bus (#02) from #06 to #0a
[   16.532000] pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
[   16.532000] cs: IO port probe 0x3000-0x3fff: clean.
[   16.532000] pcmcia: parent PCI bridge Memory window: 0xe0200000 - 0xe02fffff
[   16.532000] pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x37ffffff
[   16.540000] ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
[   16.540000] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[   16.836000] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
[   17.136000] ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
[   17.136000] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[   17.224000] cs: IO port probe 0x100-0x3af: clean.
[   17.228000] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[   17.228000] cs: IO port probe 0x820-0x8ff: clean.
[   17.228000] cs: IO port probe 0xc00-0xcf7: clean.
[   17.228000] cs: IO port probe 0xa00-0xaff: clean.
[   17.260000] cs: IO port probe 0x100-0x3af: clean.
[   17.264000] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[   17.264000] cs: IO port probe 0x820-0x8ff: clean.
[   17.264000] cs: IO port probe 0xc00-0xcf7: clean.
[   17.264000] cs: IO port probe 0xa00-0xaff: clean.
[   18.060000] intel8x0_measure_ac97_clock: measured 55496 usecs
[   18.060000] intel8x0: clocking to 48000
[   18.364000] lp: driver loaded but no devices found
[   18.452000] Adding 1196800k swap on /dev/sda6.  Priority:-1 extents:1 across:1196800k
[   19.120000] EXT3 FS on sda3, internal journal
[   20.376000] input: Power Button (FF) as /class/input/input4
[   20.380000] ACPI: Power Button (FF) [PWRF]
[   20.428000] input: Lid Switch as /class/input/input5
[   20.432000] ACPI: Lid Switch [LID0]
[   20.480000] input: Sleep Button (CM) as /class/input/input6
[   20.484000] ACPI: Sleep Button (CM) [SLPB]
[   20.528000] input: Power Button (CM) as /class/input/input7
[   20.532000] ACPI: Power Button (CM) [PWRB]
[   20.584000] No dock devices found.
[   20.592000] ACPI: Video Device [GFX0] (multi-head: yes  rom: yes  post: no)
[   20.620000] ACPI: AC Adapter [AC] (on-line)
[   20.644000] ACPI: Battery Slot [BAT0] (battery present)
[   22.024000] eth0: link down
[   22.104000] ppdev: user-space parallel port driver
[   22.524000] audit(1194520588.205:3):  type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=4583 profile="/usr/sbin/cupsd"
[   22.592000] apm: BIOS not found.
[   22.940000] Failure registering capabilities with primary security module.
[   23.208000] Bluetooth: Core ver 2.11
[   23.208000] NET: Registered protocol family 31
[   23.208000] Bluetooth: HCI device and connection manager initialized
[   23.208000] Bluetooth: HCI socket layer initialized
[   23.256000] Bluetooth: L2CAP ver 2.8
[   23.256000] Bluetooth: L2CAP socket layer initialized
[   23.332000] Bluetooth: RFCOMM socket layer initialized
[   23.332000] Bluetooth: RFCOMM TTY layer initialized
[   23.332000] Bluetooth: RFCOMM ver 1.8
[   23.564000] Clocksource tsc unstable (delta = -215268489 ns)
[   24.880000] mtrr: no more MTRRs available
[   24.880000] mtrr: no more MTRRs available
[   24.880000] mtrr: no more MTRRs available
[   53.756000] NET: Registered protocol family 17
[   53.932000] ieee80211_crypt: registered algorithm 'WEP'
[   63.460000] NET: Registered protocol family 10
[   63.460000] lo: Disabled Privacy Extensions
[   63.460000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   74.448000] eth1: no IPv6 routers present
[  739.056000] usb 2-2: USB disconnect, address 2
[  745.936000] usb 1-1: new low speed USB device using uhci_hcd and address 2
[  746.088000] usb 1-1: configuration #1 chosen from 1 choice
[  746.104000] input: HID 04b3:310b as /class/input/input8
[  746.104000] input: USB HID v1.00 Mouse [HID 04b3:310b] on usb-0000:00:1d.0-1