[ 0.000000] Linux version 2.6.20-15-lowlatency (root@palmer) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP PREEMPT Sun Apr 15 07:39:03 UTC 2007 (Ubuntu Unofficial) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] sanitize start [ 0.000000] sanitize end [ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009f800 end: 000000000009f800 type: 1 [ 0.000000] copy_e820_map() type is E820_RAM [ 0.000000] copy_e820_map() start: 000000000009f800 size: 0000000000000800 end: 00000000000a0000 type: 2 [ 0.000000] copy_e820_map() start: 00000000000d2000 size: 000000000002e000 end: 0000000000100000 type: 2 [ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000001ddf0000 end: 000000001def0000 type: 1 [ 0.000000] copy_e820_map() type is E820_RAM [ 0.000000] copy_e820_map() start: 000000001def0000 size: 000000000000f000 end: 000000001deff000 type: 3 [ 0.000000] copy_e820_map() start: 000000001deff000 size: 0000000000001000 end: 000000001df00000 type: 4 [ 0.000000] copy_e820_map() start: 000000001df00000 size: 0000000002100000 end: 0000000020000000 type: 2 [ 0.000000] copy_e820_map() start: 00000000fec00000 size: 0000000000010000 end: 00000000fec10000 type: 2 [ 0.000000] copy_e820_map() start: 00000000fee00000 size: 0000000000001000 end: 00000000fee01000 type: 2 [ 0.000000] copy_e820_map() start: 00000000fff80000 size: 0000000000080000 end: 0000000100000000 type: 2 [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable) [ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000d2000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000001def0000 (usable) [ 0.000000] BIOS-e820: 000000001def0000 - 000000001deff000 (ACPI data) [ 0.000000] BIOS-e820: 000000001deff000 - 000000001df00000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000001df00000 - 0000000020000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) [ 0.000000] 0MB HIGHMEM available. [ 0.000000] 478MB LOWMEM available. [ 0.000000] found SMP MP-table at 000f8130 [ 0.000000] Entering add_active_range(0, 0, 122608) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 122608 [ 0.000000] HighMem 122608 -> 122608 [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 122608 [ 0.000000] On node 0 totalpages: 122608 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 925 pages used for memmap [ 0.000000] Normal zone: 117587 pages, LIFO batch:31 [ 0.000000] HighMem zone: 0 pages used for memmap [ 0.000000] DMI present. [ 0.000000] ACPI: RSDP (v000 HP ) @ 0x000f8080 [ 0.000000] ACPI: RSDT (v001 HP 3097 0x20040830 LTP 0x00000000) @ 0x1def8bcf [ 0.000000] ACPI: FADT (v001 HP 3097 0x20040830 PTL 0x0000005f) @ 0x1defee2a [ 0.000000] ACPI: SSDT (v001 PTLTD POWERNOW 0x20040830 LTP 0x00000001) @ 0x1defee9e [ 0.000000] ACPI: MADT (v001 PTLTD 3097 0x20040830 LTP 0x00000000) @ 0x1defef74 [ 0.000000] ACPI: MCFG (v001 PTLTD MCFG 0x20040830 LTP 0x00000000) @ 0x1defefc4 [ 0.000000] ACPI: DSDT (v001 HP 3091 0x20040830 MSFT 0x0100000e) @ 0x00000000 [ 0.000000] ATI board detected. Disabling timer routing over 8254. [ 0.000000] ACPI: PM-Timer IO Port: 0x8008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] Processor #0 15:12 APIC version 16 [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level) [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000) [ 0.000000] Detected 1795.029 MHz processor. [ 8.818289] Built 1 zonelists. Total pages: 121651 [ 8.818293] Kernel command line: root=/dev/hda5 ro quiet splash locale=es_ES [ 8.818438] mapped APIC to ffffd000 (fee00000) [ 8.818441] mapped IOAPIC to ffffc000 (fec00000) [ 8.818444] Enabling fast FPU save and restore... done. [ 8.818447] Enabling unmasked SIMD FPU exception support... done. [ 8.818454] Initializing CPU#0 [ 8.818517] PID hash table entries: 2048 (order: 11, 8192 bytes) [ 8.819436] Console: colour VGA+ 80x25 [ 8.819713] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 8.820224] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 8.830085] Memory: 475160k/490432k available (2018k kernel code, 14736k reserved, 898k data, 328k init, 0k highmem) [ 8.830097] virtual kernel memory layout: [ 8.830098] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB) [ 8.830099] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 8.830101] vmalloc : 0xde800000 - 0xff7fe000 ( 527 MB) [ 8.830102] lowmem : 0xc0000000 - 0xddef0000 ( 478 MB) [ 8.830103] .init : 0xc03df000 - 0xc0431000 ( 328 kB) [ 8.830105] .data : 0xc02f8b15 - 0xc03d96d4 ( 898 kB) [ 8.830106] .text : 0xc0100000 - 0xc02f8b15 (2018 kB) [ 8.830109] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 8.889447] Calibrating delay using timer specific routine.. 3592.00 BogoMIPS (lpj=1796001) [ 8.889494] Security Framework v1.0.0 initialized [ 8.889499] SELinux: Disabled at boot. [ 8.889518] Mount-cache hash table entries: 512 [ 8.889652] CPU: After generic identify, caps: 078bfbff c3d3fbff 00000000 00000000 00000001 00000000 00000001 [ 8.889662] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 8.889665] CPU: L2 Cache: 128K (64 bytes/line) [ 8.889668] CPU: After all inits, caps: 078bfbff c3d3fbff 00000000 00000410 00000001 00000000 00000001 [ 8.889681] Compat vDSO mapped to ffffe000. [ 8.889684] Remapping vsyscall page to ffffe000 [ 8.889694] Checking 'hlt' instruction... OK. [ 8.893575] SMP alternatives: switching to UP code [ 8.893825] Freeing SMP alternatives: 9k freed [ 8.894025] Early unpacking initramfs... done [ 9.206504] ACPI: Core revision 20060707 [ 9.206732] ACPI: Looking for DSDT in initramfs... file /DSDT.aml not found, using machine DSDT. [ 9.210679] CPU0: AMD Mobile AMD Sempron(tm) Processor 3000+ stepping 02 [ 9.210700] Total of 1 processors activated (3592.00 BogoMIPS). [ 9.210882] ENABLING IO-APIC IRQs [ 9.211092] ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1 [ 9.323010] Brought up 1 CPUs [ 9.323238] Booting paravirtualized kernel on bare hardware [ 9.323332] Time: 9:08:19 Date: 04/13/107 [ 9.323367] NET: Registered protocol family 16 [ 9.323477] EISA bus registered [ 9.323482] ACPI: bus type pci registered [ 9.323659] PCI: PCI BIOS revision 2.10 entry at 0xfd8bc, last bus=5 [ 9.323662] PCI: Using configuration type 1 [ 9.323664] Setting up standard PCI resources [ 9.326368] ACPI: Interpreter enabled [ 9.326373] ACPI: Using IOAPIC for interrupt routing [ 9.326888] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 9.326894] PCI: Probing PCI hardware (bus 00) [ 9.328662] Boot video device is 0000:01:05.0 [ 9.329014] PCI: Transparent bridge - 0000:00:14.4 [ 9.329091] PCI: Bus #06 (-#09) is hidden behind transparent bridge #05 (-#05) (try 'pci=assign-busses') [ 9.329094] Please report the result to linux-kernel to fix this permanently [ 9.329120] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 9.331602] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled. [ 9.331828] ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled. [ 9.332060] ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled. [ 9.332280] ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled. [ 9.332499] ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled. [ 9.332719] ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled. [ 9.332938] ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled. [ 9.333199] ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled. [ 9.336398] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT] [ 9.336686] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] [ 9.337081] Linux Plug and Play Support v0.97 (c) Adam Belay [ 9.337097] pnp: PnP ACPI init [ 9.339772] pnp: PnP ACPI: found 10 devices [ 9.339778] PnPBIOS: Disabled by ACPI PNP [ 9.339839] PCI: Using ACPI for IRQ routing [ 9.339842] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 9.354197] NET: Registered protocol family 8 [ 9.354200] NET: Registered protocol family 20 [ 9.354500] pnp: 00:08: ioport range 0x1080-0x1080 has been reserved [ 9.354503] pnp: 00:08: ioport range 0x220-0x22f has been reserved [ 9.354512] pnp: 00:08: ioport range 0x40b-0x40b has been reserved [ 9.354515] pnp: 00:08: ioport range 0x4d0-0x4d1 has been reserved [ 9.354794] PCI: Bridge: 0000:00:01.0 [ 9.354797] IO window: 9000-9fff [ 9.354801] MEM window: d0100000-d01fffff [ 9.354805] PREFETCH window: d4000000-d7ffffff [ 9.354815] PCI: Bus 6, cardbus bridge: 0000:05:09.0 [ 9.354818] IO window: 0000a400-0000a4ff [ 9.354823] IO window: 0000a800-0000a8ff [ 9.354830] PREFETCH window: 30000000-33ffffff [ 9.354836] MEM window: 34000000-37ffffff [ 9.354842] PCI: Bridge: 0000:00:14.4 [ 9.354845] IO window: a000-afff [ 9.354852] MEM window: d0200000-d02fffff [ 9.354857] PREFETCH window: 30000000-33ffffff [ 9.354903] ACPI: PCI Interrupt 0000:05:09.0[A] -> GSI 17 (level, low) -> IRQ 16 [ 9.354912] PCI: Setting latency timer of device 0000:05:09.0 to 64 [ 9.354962] NET: Registered protocol family 2 [ 9.364004] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 9.364100] TCP established hash table entries: 16384 (order: 5, 196608 bytes) [ 9.364300] TCP bind hash table entries: 8192 (order: 4, 98304 bytes) [ 9.364424] TCP: Hash tables configured (established 16384 bind 8192) [ 9.364428] TCP reno registered [ 9.367061] checking if image is initramfs... it is [ 9.981269] Freeing initrd memory: 6763k freed [ 9.981734] audit: initializing netlink socket (disabled) [ 9.981748] audit(1179047299.357:1): initialized [ 9.981880] VFS: Disk quotas dquot_6.5.1 [ 9.981900] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 9.981952] io scheduler noop registered [ 9.981954] io scheduler anticipatory registered [ 9.981957] io scheduler deadline registered [ 9.981968] io scheduler cfq registered (default) [ 10.641713] isapnp: Scanning for PnP cards... [ 10.998739] isapnp: No Plug & Play device found [ 11.039649] Real Time Clock Driver v1.12ac [ 11.039692] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 11.040703] ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> IRQ 16 [ 11.040713] ACPI: PCI interrupt for device 0000:00:14.6 disabled [ 11.040786] mice: PS/2 mouse device common for all mice [ 11.041314] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 11.041467] input: Macintosh mouse button emulation as /class/input/input0 [ 11.041499] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 11.041503] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 11.041795] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12 [ 11.044284] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 11.044337] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 11.044412] EISA: Probing bus 0 at eisa.0 [ 11.044422] Cannot allocate resource for EISA slot 1 [ 11.044451] Cannot allocate resource for EISA slot 8 [ 11.044453] EISA: Detected 0 cards. [ 11.073904] input: AT Translated Set 2 keyboard as /class/input/input1 [ 11.074533] TCP cubic registered [ 11.074544] NET: Registered protocol family 1 [ 11.074568] Using IPI No-Shortcut mode [ 11.074629] ACPI: (supports S0 S3 S4 S5) [ 11.074672] Magic number: 7:985:120 [ 11.075030] Time: tsc clocksource has been installed. [ 11.075157] Freeing unused kernel memory: 328k freed [ 12.329796] Capability LSM initialized [ 12.377167] ACPI: CPU0 (power states: C1[C1] C2[C2]) [ 12.377174] ACPI: Processor [CPU0] (supports 8 throttling states) [ 12.378759] ACPI: Thermal Zone [THRM] (24 C) [ 12.963757] usbcore: registered new interface driver usbfs [ 12.963780] usbcore: registered new interface driver hub [ 12.963799] usbcore: registered new device driver usb [ 12.964594] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver [ 12.964637] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 17 [ 12.964651] ohci_hcd 0000:00:13.0: OHCI Host Controller [ 12.964766] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1 [ 12.964792] ohci_hcd 0000:00:13.0: irq 17, io mem 0xd0000000 [ 13.019580] usb usb1: configuration #1 chosen from 1 choice [ 13.019608] hub 1-0:1.0: USB hub found [ 13.019622] hub 1-0:1.0: 4 ports detected [ 13.066998] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004) [ 13.119916] ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 17 [ 13.119934] ohci_hcd 0000:00:13.1: OHCI Host Controller [ 13.119959] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2 [ 13.119976] ohci_hcd 0000:00:13.1: irq 17, io mem 0xd0001000 [ 13.174868] usb usb2: configuration #1 chosen from 1 choice [ 13.174899] hub 2-0:1.0: USB hub found [ 13.174911] hub 2-0:1.0: 4 ports detected [ 3.675000] Time: acpi_pm clocksource has been installed. [ 3.724000] ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 17 [ 3.724000] ehci_hcd 0000:00:13.2: EHCI Host Controller [ 3.725000] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3 [ 3.725000] ehci_hcd 0000:00:13.2: irq 17, io mem 0xd0002000 [ 3.725000] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 3.725000] usb usb3: configuration #1 chosen from 1 choice [ 3.726000] hub 3-0:1.0: USB hub found [ 3.726000] hub 3-0:1.0: 8 ports detected [ 3.827000] ATIIXP: IDE controller at PCI slot 0000:00:14.1 [ 3.827000] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 18 [ 3.827000] ATIIXP: chipset revision 0 [ 3.827000] ATIIXP: not 100% native mode: will probe irqs later [ 3.827000] ide0: BM-DMA at 0x8410-0x8417, BIOS settings: hda:DMA, hdb:pio [ 3.827000] ide1: BM-DMA at 0x8418-0x841f, BIOS settings: hdc:DMA, hdd:pio [ 3.827000] Probing IDE interface ide0... [ 4.091000] hda: TOSHIBA MK6025GAS, ATA DISK drive [ 4.703000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 4.753000] Probing IDE interface ide1... [ 5.425000] hdc: TSSTcorpCD/DVDW TS-L532R, ATAPI CD/DVD-ROM drive [ 6.046000] ide1 at 0x170-0x177,0x376 on irq 15 [ 6.065000] SCSI subsystem initialized [ 6.070000] libata version 2.20 loaded. [ 6.072000] 8139cp 0000:05:00.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip [ 6.072000] 8139cp 0000:05:00.0: Try the "8139too" driver instead. [ 6.075000] 8139too Fast Ethernet driver 0.9.28 [ 6.075000] ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 18 (level, low) -> IRQ 19 [ 6.076000] eth0: RealTek RTL8139 at 0xde85a000, 00:c0:9f:fd:c5:55, IRQ 19 [ 6.076000] eth0: Identified 8139 chip type 'RTL-8100B/8139D' [ 6.086000] hda: max request size: 128KiB [ 6.097000] hda: 117210240 sectors (60011 MB), CHS=65535/16/63, UDMA(100) [ 6.098000] hda: cache flushes supported [ 6.098000] hda: hda1 hda2 < hda5 hda6 hda7 > [ 6.221000] hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, DMA [ 6.221000] Uniform CD-ROM driver Revision: 3.20 [ 6.643000] Attempting manual resume [ 6.643000] swsusp: Resume From Partition 3:6 [ 6.643000] PM: Checking swsusp image. [ 6.666000] PM: Resume from disk failed. [ 6.722000] kjournald starting. Commit interval 5 seconds [ 6.722000] EXT3-fs: mounted filesystem with ordered data mode. [ 24.330000] eth0: link down [ 24.921000] NET: Registered protocol family 10 [ 24.921000] lo: Disabled Privacy Extensions [ 24.922000] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 26.373000] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device [ 26.686000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 26.695000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 26.730000] Yenta: CardBus bridge found at 0000:05:09.0 [103c:3091] [ 26.730000] Yenta: Enabling burst memory read transactions [ 26.730000] Yenta: Using CSCINT to route CSC interrupts to PCI [ 26.730000] Yenta: Routing CardBus interrupts to PCI [ 26.730000] Yenta TI: socket 0000:05:09.0, mfunc 0x01a01b22, devctl 0x66 [ 26.778000] Linux agpgart interface v0.102 (c) Dave Jones [ 26.953000] Yenta: ISA IRQ mask 0x0ee8, PCI irq 16 [ 26.953000] Socket status: 30000006 [ 26.953000] Yenta: Raising subordinate bus# of parent bus (#05) from #05 to #09 [ 26.953000] pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff [ 26.953000] cs: IO port probe 0xa000-0xafff: clean. [ 26.954000] pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xd02fffff [ 26.954000] pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x33ffffff [ 26.982000] input: PC Speaker as /class/input/input2 [ 27.070000] ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 16 [ 27.228000] ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> IRQ 16 [ 27.331000] MC'97 0 converters and GPIO not ready (0x1) [ 27.475000] cs: IO port probe 0x100-0x3af: clean. [ 27.478000] cs: IO port probe 0x3e0-0x4ff: clean. [ 27.479000] cs: IO port probe 0x820-0x8ff: excluding 0x878-0x87f [ 27.480000] cs: IO port probe 0xc00-0xcf7: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf [ 27.480000] cs: IO port probe 0xa00-0xaff: clean. [ 27.541000] Synaptics Touchpad, model: 1, fw: 5.10, id: 0x258eb1, caps: 0xa04713/0x0 [ 27.577000] input: SynPS/2 Synaptics TouchPad as /class/input/input3 [ 27.891000] lp: driver loaded but no devices found [ 27.946000] ndiswrapper version 1.38 loaded (preempt=yes,smp=yes) [ 28.082000] ndiswrapper: driver bcmwl5 (Broadcom,07/21/2005, 3.140.16.0) loaded [ 28.082000] ACPI: PCI Interrupt 0000:05:02.0[A] -> GSI 20 (level, low) -> IRQ 20 [ 28.091000] ndiswrapper: using IRQ 20 [ 28.756000] wlan0: ethernet device 00:14:a5:2a:f7:8f using NDIS driver: bcmwl5, version: 0x38c1000, NDIS version: 0x501, vendor: '', 14E4:4318.5.conf [ 28.756000] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK [ 28.757000] usbcore: registered new interface driver ndiswrapper [ 28.830000] fuse init (API version 7.8) [ 28.871000] Adding 522072k swap on /dev/disk/by-uuid/5d293319-90ad-445e-99b5-bb9256a999b3. Priority:-1 extents:1 across:522072k [ 28.877000] ndiswrapper: changing interface name from 'wlan0' to 'eth1' [ 28.882000] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 29.095000] EXT3 FS on hda5, internal journal [ 29.978000] NET: Registered protocol family 17 [ 36.605000] NTFS driver 2.1.28 [Flags: R/O MODULE]. [ 36.677000] NTFS volume version 3.1. [ 39.718000] PPP generic driver version 2.4.2 [ 41.895000] ACPI: AC Adapter [ACAD] (on-line) [ 41.994000] ACPI: Battery Slot [BAT1] (battery present) [ 42.050000] input: Power Button (FF) as /class/input/input4 [ 42.055000] ACPI: Power Button (FF) [PWRF] [ 42.093000] input: Power Button (CM) as /class/input/input5 [ 42.098000] ACPI: Power Button (CM) [PWRB] [ 42.131000] input: Sleep Button (CM) as /class/input/input6 [ 42.131000] ACPI: Sleep Button (CM) [SLPB] [ 42.148000] input: Lid Switch as /class/input/input7 [ 42.148000] ACPI: Lid Switch [LID] [ 42.200000] Using specific hotkey driver [ 42.225000] No dock devices found. [ 42.271000] ibm_acpi: ec object not found [ 42.361000] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no) [ 42.393000] pcc_acpi: loading... [ 42.403000] wmi_add device=dcbdf400 [ 42.403000] calling WQBA [ 42.738000] powernow-k8: Found 1 Mobile AMD Sempron(tm) Processor 3000+ processors (version 2.00.00) [ 42.738000] powernow-k8: 0 : fid 0xa (1800 MHz), vid 0xa [ 42.738000] powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0xc [ 42.738000] powernow-k8: 2 : fid 0x0 (800 MHz), vid 0x13 [ 47.837000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 47.986000] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory [ 47.996000] NFSD: starting 90-second grace period [ 102.718000] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 118.478000] eth1: no IPv6 routers present [ 7165.456000] hdc: status timeout: status=0xd0 { Busy } [ 7165.456000] ide: failed opcode was: unknown [ 7165.456000] hdc: drive not ready for command [ 7170.479000] hdc: status timeout: status=0xd0 { Busy } [ 7170.479000] ide: failed opcode was: unknown [ 7170.479000] hdc: drive not ready for command [ 7175.498000] hdc: status timeout: status=0xd0 { Busy } [ 7175.498000] ide: failed opcode was: unknown [ 7175.498000] hdc: drive not ready for command [ 7181.925000] hdc: status timeout: status=0xd0 { Busy } [ 7181.925000] ide: failed opcode was: unknown [ 7181.925000] hdc: drive not ready for command [ 7186.951000] hdc: status timeout: status=0xd0 { Busy } [ 7186.951000] ide: failed opcode was: unknown [ 7186.951000] hdc: drive not ready for command [ 7192.338000] hdc: status timeout: status=0xd0 { Busy } [ 7192.338000] ide: failed opcode was: unknown [ 7192.338000] hdc: drive not ready for command [ 7197.339000] hdc: status timeout: status=0xd0 { Busy } [ 7197.339000] ide: failed opcode was: unknown [ 7197.339000] hdc: drive not ready for command [ 7202.340000] hdc: status timeout: status=0xd0 { Busy } [ 7202.340000] ide: failed opcode was: unknown [ 7202.340000] hdc: drive not ready for command [ 7207.342000] hdc: status timeout: status=0xd0 { Busy } [ 7207.342000] ide: failed opcode was: unknown [ 7207.342000] hdc: drive not ready for command [ 7212.343000] hdc: status timeout: status=0xd0 { Busy } [ 7212.343000] ide: failed opcode was: unknown [ 7212.343000] hdc: drive not ready for command [ 7217.344000] hdc: status timeout: status=0xd0 { Busy } [ 7217.344000] ide: failed opcode was: unknown [ 7217.344000] hdc: drive not ready for command [ 7222.345000] hdc: status timeout: status=0xd0 { Busy } [ 7222.345000] ide: failed opcode was: unknown [ 7222.345000] hdc: drive not ready for command [ 7227.346000] hdc: status timeout: status=0xd0 { Busy } [ 7227.346000] ide: failed opcode was: unknown [ 7227.346000] hdc: drive not ready for command [ 7232.414000] hdc: status timeout: status=0xd0 { Busy } [ 7232.414000] ide: failed opcode was: unknown [ 7232.415000] hdc: drive not ready for command [ 7237.646000] hdc: status timeout: status=0xd0 { Busy } [ 7237.646000] ide: failed opcode was: unknown [ 7237.648000] hdc: drive not ready for command [ 7242.716000] hdc: status timeout: status=0xd0 { Busy } [ 7242.716000] ide: failed opcode was: unknown [ 7242.716000] hdc: drive not ready for command [ 7247.788000] hdc: status timeout: status=0xd0 { Busy } [ 7247.788000] ide: failed opcode was: unknown [ 7247.788000] hdc: drive not ready for command [ 7252.965000] hdc: status timeout: status=0xd0 { Busy } [ 7252.965000] ide: failed opcode was: unknown [ 7252.965000] hdc: drive not ready for command [ 7258.016000] hdc: status timeout: status=0xd0 { Busy } [ 7258.016000] ide: failed opcode was: unknown [ 7258.016000] hdc: drive not ready for command [ 7263.061000] hdc: status timeout: status=0xd0 { Busy } [ 7263.061000] ide: failed opcode was: unknown [ 7263.061000] hdc: drive not ready for command [ 7268.090000] hdc: status timeout: status=0xd0 { Busy } [ 7268.090000] ide: failed opcode was: unknown [ 7268.090000] hdc: drive not ready for command [ 7273.106000] hdc: status timeout: status=0xd0 { Busy } [ 7273.106000] ide: failed opcode was: unknown [ 7273.106000] hdc: drive not ready for command [ 7278.133000] hdc: status timeout: status=0xd0 { Busy } [ 7278.133000] ide: failed opcode was: unknown [ 7278.133000] hdc: drive not ready for command [ 7283.171000] hdc: status timeout: status=0xd0 { Busy } [ 7283.171000] ide: failed opcode was: unknown [ 7283.171000] hdc: drive not ready for command [ 7288.195000] hdc: status timeout: status=0xd0 { Busy } [ 7288.195000] ide: failed opcode was: unknown [ 7288.195000] hdc: drive not ready for command [ 7293.233000] hdc: status timeout: status=0xd0 { Busy } [ 7293.233000] ide: failed opcode was: unknown [ 7293.233000] hdc: drive not ready for command [ 7298.262000] hdc: status timeout: status=0xd0 { Busy } [ 7298.262000] ide: failed opcode was: unknown [ 7298.265000] hdc: drive not ready for command [ 7303.308000] hdc: status timeout: status=0xd0 { Busy } [ 7303.308000] ide: failed opcode was: unknown [ 7303.308000] hdc: drive not ready for command [ 7308.334000] hdc: status timeout: status=0xd0 { Busy } [ 7308.334000] ide: failed opcode was: unknown [ 7308.334000] hdc: drive not ready for command [ 7313.359000] hdc: status timeout: status=0xd0 { Busy } [ 7313.359000] ide: failed opcode was: unknown [ 7313.359000] hdc: drive not ready for command [ 7318.446000] hdc: status timeout: status=0xd0 { Busy } [ 7318.446000] ide: failed opcode was: unknown [ 7318.448000] hdc: drive not ready for command [ 7323.517000] hdc: status timeout: status=0xd0 { Busy } [ 7323.517000] ide: failed opcode was: unknown [ 7323.517000] hdc: drive not ready for command [ 7328.564000] hdc: status timeout: status=0xd0 { Busy } [ 7328.564000] ide: failed opcode was: unknown [ 7328.564000] hdc: drive not ready for command [ 7333.655000] hdc: status timeout: status=0xd0 { Busy } [ 7333.655000] ide: failed opcode was: unknown [ 7333.655000] hdc: drive not ready for command [ 7338.686000] hdc: status timeout: status=0xd0 { Busy } [ 7338.686000] ide: failed opcode was: unknown [ 7338.686000] hdc: drive not ready for command [ 7343.720000] hdc: status timeout: status=0xd0 { Busy } [ 7343.720000] ide: failed opcode was: unknown [ 7343.720000] hdc: drive not ready for command [ 7348.775000] hdc: status timeout: status=0xd0 { Busy } [ 7348.775000] ide: failed opcode was: unknown [ 7348.775000] hdc: drive not ready for command [ 7353.812000] hdc: status timeout: status=0xd0 { Busy } [ 7353.812000] ide: failed opcode was: unknown [ 7353.812000] hdc: drive not ready for command [ 7358.908000] hdc: status timeout: status=0xd0 { Busy } [ 7358.908000] ide: failed opcode was: unknown [ 7358.908000] hdc: drive not ready for command [ 7363.990000] hdc: status timeout: status=0xd0 { Busy } [ 7363.990000] ide: failed opcode was: unknown [ 7363.990000] hdc: drive not ready for command [ 7369.116000] hdc: status timeout: status=0xd0 { Busy } [ 7369.116000] ide: failed opcode was: unknown [ 7369.116000] hdc: drive not ready for command [ 7374.219000] hdc: status timeout: status=0xd0 { Busy } [ 7374.219000] ide: failed opcode was: unknown [ 7374.221000] hdc: drive not ready for command [ 7379.260000] hdc: status timeout: status=0xd0 { Busy } [ 7379.260000] ide: failed opcode was: unknown [ 7379.260000] hdc: drive not ready for command [ 7384.296000] hdc: status timeout: status=0xd0 { Busy } [ 7384.296000] ide: failed opcode was: unknown [ 7384.296000] hdc: drive not ready for command [ 7389.312000] hdc: status timeout: status=0xd0 { Busy } [ 7389.312000] ide: failed opcode was: unknown [ 7389.312000] hdc: drive not ready for command [ 7394.356000] hdc: status timeout: status=0xd0 { Busy } [ 7394.356000] ide: failed opcode was: unknown [ 7394.357000] hdc: drive not ready for command [ 7399.387000] hdc: status timeout: status=0xd0 { Busy } [ 7399.387000] ide: failed opcode was: unknown [ 7399.387000] hdc: drive not ready for command [ 7404.414000] hdc: status timeout: status=0xd0 { Busy } [ 7404.414000] ide: failed opcode was: unknown [ 7404.414000] hdc: drive not ready for command [ 7409.446000] hdc: status timeout: status=0xd0 { Busy } [ 7409.446000] ide: failed opcode was: unknown [ 7409.446000] hdc: drive not ready for command [ 7414.495000] hdc: status timeout: status=0xd0 { Busy } [ 7414.495000] ide: failed opcode was: unknown [ 7414.495000] hdc: drive not ready for command [ 7419.527000] hdc: status timeout: status=0xd0 { Busy } [ 7419.527000] ide: failed opcode was: unknown [ 7419.527000] hdc: drive not ready for command [ 7424.555000] hdc: status timeout: status=0xd0 { Busy } [ 7424.555000] ide: failed opcode was: unknown [ 7424.555000] hdc: drive not ready for command [16377.522000] hdc: status timeout: status=0xd0 { Busy } [16377.522000] ide: failed opcode was: unknown [16377.522000] hdc: drive not ready for command [16382.578000] hdc: status timeout: status=0xd0 { Busy } [16382.578000] ide: failed opcode was: unknown [16382.578000] hdc: drive not ready for command [16387.658000] hdc: status timeout: status=0xd0 { Busy } [16387.658000] ide: failed opcode was: unknown [16387.658000] hdc: drive not ready for command [16392.718000] hdc: status timeout: status=0xd0 { Busy } [16392.718000] ide: failed opcode was: unknown [16392.718000] hdc: drive not ready for command [16397.783000] hdc: status timeout: status=0xd0 { Busy } [16397.783000] ide: failed opcode was: unknown [16397.783000] hdc: drive not ready for command [16402.836000] hdc: status timeout: status=0xd0 { Busy } [16402.836000] ide: failed opcode was: unknown [16402.836000] hdc: drive not ready for command [16468.371000] hdc: status timeout: status=0xd0 { Busy } [16468.371000] ide: failed opcode was: unknown [16468.371000] hdc: drive not ready for command [16473.424000] hdc: status timeout: status=0xd0 { Busy } [16473.424000] ide: failed opcode was: unknown [16473.424000] hdc: drive not ready for command [16478.488000] hdc: status timeout: status=0xd0 { Busy } [16478.488000] ide: failed opcode was: unknown [16478.488000] hdc: drive not ready for command [16483.551000] hdc: status timeout: status=0xd0 { Busy } [16483.551000] ide: failed opcode was: unknown [16483.551000] hdc: drive not ready for command [16488.610000] hdc: status timeout: status=0xd0 { Busy } [16488.610000] ide: failed opcode was: unknown [16488.610000] hdc: drive not ready for command [16493.741000] hdc: status timeout: status=0xd0 { Busy } [16493.741000] ide: failed opcode was: unknown [16493.741000] hdc: drive not ready for command [16578.392000] hdc: status timeout: status=0xd0 { Busy } [16578.392000] ide: failed opcode was: unknown [16578.392000] hdc: drive not ready for command [16583.442000] hdc: status timeout: status=0xd0 { Busy } [16583.442000] ide: failed opcode was: unknown [16583.442000] hdc: drive not ready for command [16588.492000] hdc: status timeout: status=0xd0 { Busy } [16588.492000] ide: failed opcode was: unknown [16588.492000] hdc: drive not ready for command [16593.549000] hdc: status timeout: status=0xd0 { Busy } [16593.549000] ide: failed opcode was: unknown [16593.549000] hdc: drive not ready for command [16598.630000] hdc: status timeout: status=0xd0 { Busy } [16598.630000] ide: failed opcode was: unknown [16598.630000] hdc: drive not ready for command [16603.686000] hdc: status timeout: status=0xd0 { Busy } [16603.686000] ide: failed opcode was: unknown [16603.686000] hdc: drive not ready for command