[   67.717244] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   78.083265] wlan0: authenticate with AP 00:14:bf:8a:16:7d
[   78.096009] wlan0: authenticated
[   78.096013] wlan0: associate with AP 00:14:bf:8a:16:7d
[   78.097774] wlan0: RX AssocResp from 00:14:bf:8a:16:7d (capab=0x401 status=0 aid=1)
[   78.097776] wlan0: associated
[   78.098067] wlan0: disassociating by local choice (reason=3)
[   93.534210] eth0: link down
[   93.534591] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  120.973199] UDF-fs: Partition marked readonly; forcing readonly mount
[  121.046145] UDF-fs INFO UDF: Mounting volume 'GROUND_CONTROL', timestamp 2006/02/02 08:18 (1000)
[  127.353932] wlan0: authenticate with AP 00:14:bf:8a:16:7d
[  127.355788] wlan0: authenticated
[  127.355792] wlan0: associate with AP 00:14:bf:8a:16:7d
[  127.357682] wlan0: RX ReassocResp from 00:14:bf:8a:16:7d (capab=0x401 status=0 aid=1)
[  127.357686] wlan0: associated
[  127.360331] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  138.216023] wlan0: no IPv6 routers present
[ 1303.144040] ACPI: EC: missing confirmations, switch off interrupt mode.
[ 4339.174307] atkbd.c: Unknown key pressed (translated set 2, code 0xf2 on isa0060/serio0).
[ 4339.174316] atkbd.c: Use 'setkeycodes e072 <keycode>' to make it known.
[ 4339.457774] atkbd.c: Unknown key released (translated set 2, code 0xf2 on isa0060/serio0).
[ 4339.457779] atkbd.c: Use 'setkeycodes e072 <keycode>' to make it known.
[ 4375.456048] usb 1-3: new high speed USB device using ehci_hcd and address 2
[ 4375.623484] usb 1-3: configuration #1 chosen from 1 choice
[ 4375.787319] Initializing USB Mass Storage driver...
[ 4375.797696] scsi2 : SCSI emulation for USB Mass Storage devices
[ 4375.797890] usbcore: registered new interface driver usb-storage
[ 4375.797897] USB Mass Storage support registered.
[ 4375.797906] usb-storage: device found at 2
[ 4375.797910] usb-storage: waiting for device to settle before scanning
[ 4375.804278] usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x03F0 pid 0x6811
[ 4375.804310] usbcore: registered new interface driver usblp
[ 4380.796253] usb-storage: device scan complete
[ 4380.836879] scsi 2:0:0:0: Direct-Access     HP       Photosmart D5300 1.00 PQ: 0 ANSI: 5
[ 4380.885144] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 4380.885272] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 4391.729978] ppdev: user-space parallel port driver
[ 4400.431341] ath5k phy0: noise floor calibration timeout (2412MHz)
[ 4520.441604] ath5k phy0: noise floor calibration timeout (2412MHz)
[ 4576.032040] wlan0: No ProbeResp from current AP 00:14:bf:8a:16:7d - assume out of range
[ 4576.495323] ath5k phy0: noise floor calibration timeout (2412MHz)
[ 4586.119981] wlan0: authenticate with AP 00:14:bf:8a:16:7d
[ 4586.320052] wlan0: authenticate with AP 00:14:bf:8a:16:7d
[ 4586.393451] wlan0: authenticated
[ 4586.393460] wlan0: associate with AP 00:14:bf:8a:16:7d
[ 4586.592049] wlan0: associate with AP 00:14:bf:8a:16:7d
[ 4586.792049] wlan0: associate with AP 00:14:bf:8a:16:7d
[ 4586.992035] wlan0: association with AP 00:14:bf:8a:16:7d timed out
[ 4591.320253] wlan0: direct probe to AP 00:14:bf:8a:16:7d try 1
[ 4591.520138] wlan0: direct probe to AP 00:14:bf:8a:16:7d try 2
[ 4591.720047] wlan0: direct probe to AP 00:14:bf:8a:16:7d try 3
[ 4591.920042] wlan0: direct probe to AP 00:14:bf:8a:16:7d timed out
[ 4592.315373] ath5k phy0: noise floor calibration timeout (2412MHz)
[ 4601.961578] wlan0: authenticate with AP 00:14:bf:8a:16:7d
[ 4601.963647] wlan0: authenticated
[ 4601.963655] wlan0: associate with AP 00:14:bf:8a:16:7d
[ 4601.969100] wlan0: RX AssocResp from 00:14:bf:8a:16:7d (capab=0x401 status=0 aid=1)
[ 4601.969107] wlan0: associated
[ 4640.427175] ath5k phy0: noise floor calibration timeout (2412MHz)
[ 4650.043315] wlan0 direct probe responded
[ 4650.043326] wlan0: authenticate with AP 00:14:bf:8a:16:7d
[ 4650.045130] wlan0: authenticated
[ 4650.045138] wlan0: associate with AP 00:14:bf:8a:16:7d
[ 4650.047233] wlan0: RX ReassocResp from 00:14:bf:8a:16:7d (capab=0x401 status=0 aid=1)
[ 4650.047239] wlan0: associated