[   22.091206] ppdev: user-space parallel port driver
[   32.232015] wlan0: no IPv6 routers present
[  125.636023] usb 1-3: new high speed USB device using ehci_hcd and address 5
[  125.772367] usb 1-3: configuration #1 chosen from 1 choice
[  125.809216] Initializing USB Mass Storage driver...
[  125.809496] scsi2 : SCSI emulation for USB Mass Storage devices
[  125.809846] usbcore: registered new interface driver usb-storage
[  125.809853] USB Mass Storage support registered.
[  125.820085] usb-storage: device found at 5
[  125.820092] usb-storage: waiting for device to settle before scanning
[  129.816034] usb 1-5: new high speed USB device using ehci_hcd and address 6
[  129.952001] usb 1-5: configuration #1 chosen from 1 choice
[  129.954888] scsi3 : SCSI emulation for USB Mass Storage devices
[  129.972377] usb-storage: device found at 6
[  129.972383] usb-storage: waiting for device to settle before scanning
[  130.820284] usb-storage: device scan complete
[  130.820878] scsi 2:0:0:0: Direct-Access     Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 2
[  130.825540] sd 2:0:0:0: Attached scsi generic sg1 type 0
[  130.829033] sd 2:0:0:0: [sdb] 1986560 512-byte logical blocks: (1.01 GB/970 MiB)
[  130.839002] sd 2:0:0:0: [sdb] Write Protect is off
[  130.839014] sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
[  130.839021] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[  130.841584] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[  130.841598]  sdb: sdb1
[  130.930235] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[  130.930249] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[  134.972283] usb-storage: device scan complete
[  137.435614] scsi 3:0:0:0: Direct-Access     Lexar    JD FireFly       1100 PQ: 0 ANSI: 0 CCS
[  137.440526] sd 3:0:0:0: Attached scsi generic sg2 type 0
[  137.455337] sd 3:0:0:0: [sdc] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
[  137.456441] sd 3:0:0:0: [sdc] Write Protect is off
[  137.456452] sd 3:0:0:0: [sdc] Mode Sense: 43 00 00 00
[  137.456459] sd 3:0:0:0: [sdc] Assuming drive cache: write through
[  137.459355] sd 3:0:0:0: [sdc] Assuming drive cache: write through
[  137.459371]  sdc: sdc1
[  137.466329] sd 3:0:0:0: [sdc] Assuming drive cache: write through
[  137.466343] sd 3:0:0:0: [sdc] Attached SCSI removable disk
[ 3048.556314] usb 2-2: USB disconnect, address 3
[ 3048.556535] usb 2-2: wlan0: rx urb failed: -108
[ 3158.896021] usb 2-2: new full speed USB device using ohci_hcd and address 4
[ 3159.061518] usb 2-2: configuration #1 chosen from 1 choice
[ 3159.062737] usb 2-2: firmware: requesting zd1201.fw
[ 3159.759876] usb 2-2: wlan0: ZD1201 USB Wireless interface
[ 3170.584012] wlan0: no IPv6 routers present
[ 3587.470492] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 3653.829781] usb 2-2: USB disconnect, address 4
[ 3653.830540] usb 2-2: wlan0: rx urb failed: -108
[ 3688.516023] usb 2-2: new full speed USB device using ohci_hcd and address 5
[ 3688.686373] usb 2-2: configuration #1 chosen from 1 choice
[ 3688.687539] usb 2-2: firmware: requesting zd1201.fw
[ 3689.388639] usb 2-2: wlan0: ZD1201 USB Wireless interface
[ 3746.842124] r8169: eth0: link down
[ 3746.842677] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3757.576011] wlan0: no IPv6 routers present
[ 3891.280243] usbcore: deregistering interface driver zd1201
[ 3891.280345] usb 2-2: wlan0: rx urb failed: -108
[ 3893.480061] usb 2-2: firmware: requesting zd1201.fw
[ 3894.484792] usb 2-2: zd1201 firmware upload failed: -110
[ 3894.484826] zd1201: probe of 2-2:1.0 failed with error -110
[ 3894.484889] usbcore: registered new interface driver zd1201
[ 3923.315347] usb 2-2: USB disconnect, address 5
[ 3929.268026] usb 2-2: new full speed USB device using ohci_hcd and address 6
[ 3929.433570] usb 2-2: configuration #1 chosen from 1 choice
[ 3929.434719] usb 2-2: firmware: requesting zd1201.fw
[ 3930.134996] usb 2-2: wlan0: ZD1201 USB Wireless interface
[ 3941.028014] wlan0: no IPv6 routers present
[ 4018.855474] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 4159.485512] usb 2-2: USB disconnect, address 6
[ 4159.486125] usb 2-2: wlan0: rx urb failed: -108
[ 4168.604021] usb 2-2: new full speed USB device using ohci_hcd and address 7
[ 4168.769652] usb 2-2: configuration #1 chosen from 1 choice
[ 4168.770776] usb 2-2: firmware: requesting zd1201.fw
[ 4169.475905] usb 2-2: wlan0: ZD1201 USB Wireless interface
[ 4200.732011] wlan0: no IPv6 routers present