[4294667.296000] Linux version 2.6.15-21-k7 (buildd@rothera) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 SMP PREEMPT Fri Apr 21 17:10:51 UTC 2006
[4294667.296000] BIOS-provided physical RAM map:
[4294667.296000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[4294667.296000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[4294667.296000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[4294667.296000]  BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
[4294667.296000]  BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
[4294667.296000]  BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
[4294667.296000]  BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[4294667.296000] 0MB HIGHMEM available.
[4294667.296000] 511MB LOWMEM available.
[4294667.296000] On node 0 totalpages: 131056
[4294667.296000]   DMA zone: 4096 pages, LIFO batch:0
[4294667.296000]   DMA32 zone: 0 pages, LIFO batch:0
[4294667.296000]   Normal zone: 126960 pages, LIFO batch:31
[4294667.296000]   HighMem zone: 0 pages, LIFO batch:0
[4294667.296000] DMI 2.3 present.
[4294667.296000] ACPI: RSDP (v000 VT8363                                ) @ 0x000f7ee0
[4294667.296000] ACPI: RSDT (v001 VT8363 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
[4294667.296000] ACPI: FADT (v001 VT8363 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
[4294667.296000] ACPI: DSDT (v001 VT8363 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
[4294667.296000] ACPI: PM-Timer IO Port: 0x4008
[4294667.296000] Allocating PCI resources starting at 30000000 (gap: 20000000:dfff0000)
[4294667.296000] Built 1 zonelists
[4294667.296000] Kernel command line: root=/dev/hda1 ro quiet splash
[4294667.296000] Local APIC disabled by BIOS (or by default) -- you can enable it with "lapic"
[4294667.296000] mapped APIC to ffffd000 (014c3000)
[4294667.296000] Initializing CPU#0
[4294667.296000] PID hash table entries: 2048 (order: 11, 32768 bytes)
[4294667.296000] Detected 1302.719 MHz processor.
[4294667.296000] Using pmtmr for high-res timesource
[4294667.296000] Console: colour VGA+ 80x25
[4294670.977000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[4294670.980000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[4294671.013000] Memory: 507912k/524224k available (2085k kernel code, 15676k reserved, 594k data, 328k init, 0k highmem)
[4294671.013000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[4294671.073000] Calibrating delay using timer specific routine.. 2606.34 BogoMIPS (lpj=1303172)
[4294671.073000] Security Framework v1.0.0 initialized
[4294671.073000] SELinux:  Disabled at boot.
[4294671.073000] Mount-cache hash table entries: 512
[4294671.073000] CPU: After generic identify, caps: 0183f9ff c1c7f9ff 00000000 00000000 00000000 00000000 00000000
[4294671.073000] CPU: After vendor identify, caps: 0183f9ff c1c7f9ff 00000000 00000000 00000000 00000000 00000000
[4294671.073000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[4294671.073000] CPU: L2 Cache: 256K (64 bytes/line)
[4294671.073000] CPU: After all inits, caps: 0183f9ff c1c7f9ff 00000000 00000020 00000000 00000000 00000000
[4294671.073000] mtrr: v2.0 (20020519)
[4294671.073000] Enabling fast FPU save and restore... done.
[4294671.073000] Checking 'hlt' instruction... OK.
[4294671.077000] SMP alternatives: switching to UP code
[4294671.077000] checking if image is initramfs... it is
[4294671.918000] Freeing initrd memory: 6543k freed
[4294671.946000] ACPI: Looking for DSDT ... not found!
[4294671.948000] ACPI: setting ELCR to 0800 (from 0e00)
[4294671.949000] CPU0: AMD Athlon(tm) processor stepping 02
[4294671.949000] SMP motherboard not detected.
[4294671.949000] Local APIC not detected. Using dummy APIC emulation.
[4294671.949000] Brought up 1 CPUs
[4294671.950000] NET: Registered protocol family 16
[4294671.950000] EISA bus registered
[4294671.950000] ACPI: bus type pci registered
[4294671.966000] PCI: PCI BIOS revision 2.10 entry at 0xfb440, last bus=1
[4294671.966000] PCI: Using configuration type 1
[4294671.967000] ACPI: Subsystem revision 20051216
[4294671.977000] ACPI: Interpreter enabled
[4294671.977000] ACPI: Using PIC for interrupt routing
[4294671.978000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[4294671.978000] PCI: Probing PCI hardware (bus 00)
[4294671.978000] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
[4294671.980000] PCI quirk: region 6000-607f claimed by vt82c686 HW-mon
[4294671.980000] PCI quirk: region 5000-500f claimed by vt82c686 SMB
[4294671.981000] Boot video device is 0000:01:00.0
[4294671.981000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[4294671.997000] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
[4294671.998000] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[4294671.998000] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
[4294671.999000] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *9
[4294672.002000] Linux Plug and Play Support v0.97 (c) Adam Belay
[4294672.002000] pnp: PnP ACPI init
[4294672.006000] pnp: PnP ACPI: found 12 devices
[4294672.006000] PnPBIOS: Disabled by ACPI PNP
[4294672.006000] PCI: Using ACPI for IRQ routing
[4294672.006000] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[4294672.028000] PCI: Bridge: 0000:00:01.0
[4294672.028000]   IO window: disabled.
[4294672.028000]   MEM window: dc000000-ddffffff
[4294672.028000]   PREFETCH window: d0000000-d7ffffff
[4294672.028000] PCI: Setting latency timer of device 0000:00:01.0 to 64
[4294672.028000] audit: initializing netlink socket (disabled)
[4294672.028000] audit(1145941206.026:1): initialized
[4294672.029000] VFS: Disk quotas dquot_6.5.1
[4294672.029000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[4294672.029000] Initializing Cryptographic API
[4294672.029000] io scheduler noop registered
[4294672.029000] io scheduler anticipatory registered
[4294672.029000] io scheduler deadline registered
[4294672.029000] io scheduler cfq registered
[4294672.029000] Applying VIA southbridge workaround.
[4294672.029000] PCI: Disabling Via external APIC routing
[4294672.029000] isapnp: Scanning for PnP cards...
[4294672.386000] isapnp: No Plug & Play device found
[4294672.408000] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[4294672.408000] serio: i8042 AUX port at 0x60,0x64 irq 12
[4294672.408000] serio: i8042 KBD port at 0x60,0x64 irq 1
[4294672.408000] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
[4294672.408000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[4294672.408000] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[4294672.411000] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[4294672.411000] 00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[4294672.412000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[4294672.412000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[4294672.412000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[4294672.413000] mice: PS/2 mouse device common for all mice
[4294672.413000] EISA: Probing bus 0 at eisa.0
[4294672.413000] Cannot allocate resource for EISA slot 4
[4294672.413000] Cannot allocate resource for EISA slot 5
[4294672.413000] Cannot allocate resource for EISA slot 6
[4294672.413000] EISA: Detected 0 cards.
[4294672.413000] NET: Registered protocol family 2
[4294672.422000] IP route cache hash table entries: 8192 (order: 3, 32768 bytes)
[4294672.422000] TCP established hash table entries: 32768 (order: 6, 393216 bytes)
[4294672.424000] TCP bind hash table entries: 32768 (order: 6, 393216 bytes)
[4294672.426000] TCP: Hash tables configured (established 32768 bind 32768)
[4294672.426000] TCP reno registered
[4294672.426000] TCP bic registered
[4294672.426000] NET: Registered protocol family 1
[4294672.426000] NET: Registered protocol family 8
[4294672.426000] NET: Registered protocol family 20
[4294672.426000] Using IPI No-Shortcut mode
[4294672.427000] ACPI wakeup devices: 
[4294672.427000] SLPB PCI0 USB0 USB1 MODM UAR1 UAR2 ECP1 
[4294672.427000] ACPI: (supports S0 S1 S4 S5)
[4294672.427000] Freeing unused kernel memory: 328k freed
[4294672.437000] input: AT Translated Set 2 keyboard as /class/input/input0
[4294672.546000] vga16fb: initializing
[4294672.546000] vga16fb: mapped to 0xc00a0000
[4294672.674000] Console: switching to colour frame buffer device 80x25
[4294672.674000] fb0: VGA16 VGA frame buffer device
[4294673.811000] Capability LSM initialized
[4294673.860000] ACPI: Fan [FAN] (on)
[4294673.866000] ACPI: CPU0 (power states: C1[C1] C2[C2])
[4294673.866000] ACPI: Processor [CPU0] (supports 2 throttling states)
[4294673.868000] ACPI: Thermal Zone [THRM] (32 C)
[4294674.734000] VP_IDE: IDE controller at PCI slot 0000:00:07.1
[4294674.734000] PCI: Via IRQ fixup for 0000:00:07.1, from 255 to 0
[4294674.734000] VP_IDE: chipset revision 6
[4294674.734000] VP_IDE: not 100% native mode: will probe irqs later
[4294674.734000] VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1
[4294674.734000]     ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:pio
[4294674.734000]     ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:DMA
[4294674.734000] Probing IDE interface ide0...
[4294675.120000] hda: IC35L040AVER07-0, ATA DISK drive
[4294675.732000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[4294675.732000] Probing IDE interface ide1...
[4294676.527000] hdc: Hewlett-Packard CD-Writer Plus 8100, ATAPI CD/DVD-ROM drive
[4294677.241000] hdd: CD-ROM 24X/AKOx, ATAPI CD/DVD-ROM drive
[4294677.293000] ide1 at 0x170-0x177,0x376 on irq 15
[4294677.307000] hda: max request size: 128KiB
[4294677.326000] hda: 80418240 sectors (41174 MB) w/1916KiB Cache, CHS=65535/16/63, UDMA(100)
[4294677.327000] hda: cache flushes not supported
[4294677.327000]  hda: hda1 hda2 hda3
[4294677.359000] hdc: ATAPI 24X CD-ROM CD-R/RW drive, 1024kB Cache, DMA
[4294677.359000] Uniform CD-ROM driver Revision: 3.20
[4294677.368000] hdd: ATAPI 24X CD-ROM drive, 120kB Cache, DMA
[4294677.559000] usbcore: registered new driver usbfs
[4294677.559000] usbcore: registered new driver hub
[4294677.562000] USB Universal Host Controller Interface driver v2.3
[4294677.563000] **** SET: Misaligned resource pointer: dfcdeaa2 Type 07 Len 0
[4294677.563000] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
[4294677.563000] PCI: setting IRQ 10 as level-triggered
[4294677.563000] ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
[4294677.563000] PCI: Via IRQ fixup for 0000:00:07.2, from 9 to 10
[4294677.563000] uhci_hcd 0000:00:07.2: UHCI Host Controller
[4294677.564000] uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
[4294677.564000] uhci_hcd 0000:00:07.2: irq 10, io base 0x0000d400
[4294677.564000] hub 1-0:1.0: USB hub found
[4294677.564000] hub 1-0:1.0: 2 ports detected
[4294677.665000] ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
[4294677.665000] PCI: Via IRQ fixup for 0000:00:07.3, from 9 to 10
[4294677.665000] uhci_hcd 0000:00:07.3: UHCI Host Controller
[4294677.665000] uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
[4294677.665000] uhci_hcd 0000:00:07.3: irq 10, io base 0x0000d800
[4294677.666000] hub 2-0:1.0: USB hub found
[4294677.666000] hub 2-0:1.0: 2 ports detected
[4294677.871000] usb 1-1: new full speed USB device using uhci_hcd and address 2
[4294677.900000] Attempting manual resume
[4294677.913000] ReiserFS: hda1: found reiserfs format "3.6" with standard journal
[4294678.000000] hub 1-1:1.0: USB hub found
[4294678.002000] hub 1-1:1.0: 4 ports detected
[4294678.550000] ReiserFS: hda1: using ordered data mode
[4294678.564000] ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[4294678.567000] ReiserFS: hda1: checking transaction log (hda1)
[4294678.607000] ReiserFS: hda1: Using r5 hash to sort names
[4294693.243000] **** SET: Misaligned resource pointer: dfcde622 Type 07 Len 0
[4294693.244000] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[4294693.244000] PCI: setting IRQ 11 as level-triggered
[4294693.244000] ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[4294693.244000] 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
[4294693.244000] 0000:00:0d.0: 3Com PCI 3c905B Cyclone 100baseTx at e088c000. Vers LK1.1.19
[4294693.306000] parport_pc: VIA 686A/8231 detected
[4294693.306000] parport_pc: probing current configuration
[4294693.306000] parport_pc: Current parallel port base: 0x378
[4294693.306000] parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
[4294693.322000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[4294693.331000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[4294693.362000] Linux agpgart interface v0.101 (c) Dave Jones
[4294693.391000] parport_pc: VIA parallel port: io=0x378, irq=7
[4294693.478000] Floppy drive(s): fd0 is 1.44M
[4294693.530000] FDC 0 is a post-1991 82077
[4294693.830000] nvidia: module license 'NVIDIA' taints kernel.
[4294693.841000] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[4294693.842000] NVRM: loading NVIDIA Linux x86 Kernel Module  1.0-8756  Wed Mar 29 14:26:26 PST 2006
[4294694.034000] input: PC Speaker as /class/input/input1
[4294694.128000] logips2pp: Detected unknown logitech mouse model 62
[4294694.146000] agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
[4294694.152000] agpgart: AGP aperture is 64M @ 0xd8000000
[4294694.170000] Real Time Clock Driver v1.12
[4294694.194000] input: ImExPS/2 Logitech Explorer Mouse as /class/input/input2
[4294694.705000] ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[4294694.818000] **** SET: Misaligned resource pointer: da6de7c2 Type 07 Len 0
[4294694.818000] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
[4294694.818000] ACPI: PCI Interrupt 0000:00:07.5[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
[4294694.818000] PCI: Setting latency timer of device 0000:00:07.5 to 64
[4294694.875000] ts: Compaq touchscreen protocol output
[4294695.106000] NET: Registered protocol family 10
[4294695.107000] lo: Disabled Privacy Extensions
[4294695.107000] IPv6 over IPv4 tunneling driver
[4294695.879000] Intel ISA PCIC probe: not found.
[4294696.073000] lp0: using parport0 (interrupt-driven).
[4294696.205000] Adding 499960k swap on /dev/hda2.  Priority:-1 extents:1 across:499960k
[4294697.245000] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
[4294697.245000] md: bitmap version 4.39
[4294698.102000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
[4294698.426000] cdrom: open failed.
[4294698.792000] cdrom: open failed.
[4294702.379000] ReiserFS: hda3: found reiserfs format "3.6" with standard journal
[4294702.383000] ReiserFS: hda3: using ordered data mode
[4294702.383000] ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[4294702.387000] ReiserFS: hda3: checking transaction log (hda3)
[4294702.388000] ReiserFS: hda3: Using r5 hash to sort names
[4294705.035000] pcc_acpi: loading...
[4294705.060000] ACPI: Power Button (FF) [PWRF]
[4294705.060000] ACPI: Power Button (CM) [PWRB]
[4294705.060000] ACPI: Sleep Button (CM) [SLPB]
[4294705.169000] ibm_acpi: ec object not found
[4294705.741000] powernow: No powernow capabilities detected
[4294705.998000] eth0: no IPv6 routers present
[4294717.941000] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[4294717.941000] apm: overridden by ACPI.
[4294718.123000] ip_tables: (C) 2000-2002 Netfilter core team
[4294718.186000] Netfilter messages via NETLINK v0.30.
[4294718.200000] ip_conntrack version 2.4 (4095 buckets, 32760 max) - 232 bytes per conntrack
[4294719.667000] hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
[4294719.667000] hdc: drive_cmd: error=0x04 { AbortedCommand }
[4294719.667000] ide: failed opcode was: 0xec
[4294729.668000] hdc: lost interrupt
[4294729.899000] hdd: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
[4294729.899000] hdd: drive_cmd: error=0x04 { AbortedCommand }
[4294729.899000] ide: failed opcode was: 0xec
[4294739.900000] hdd: irq timeout: status=0xd0 { Busy }
[4294739.900000] ide: failed opcode was: 0xa1
[4294740.282000] hdd: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
[4294740.282000] hdd: drive_cmd: error=0x04 { AbortedCommand }
[4294740.282000] ide: failed opcode was: 0xe3
[4294740.319000] hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
[4294740.319000] hdc: drive_cmd: error=0x04 { AbortedCommand }
[4294740.319000] ide: failed opcode was: 0xec
[4294750.320000] hdc: lost interrupt
[4294750.548000] hdd: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
[4294750.548000] hdd: drive_cmd: error=0x04 { AbortedCommand }
[4294750.548000] ide: failed opcode was: 0xec
[4294760.549000] hdd: irq timeout: status=0xd0 { Busy }
[4294760.549000] ide: failed opcode was: 0xa1
[4294760.828000] hdd: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
[4294760.828000] hdd: drive_cmd: error=0x04 { AbortedCommand }
[4294760.828000] ide: failed opcode was: 0xef
[4294761.274000] Bluetooth: Core ver 2.8
[4294761.274000] NET: Registered protocol family 31
[4294761.274000] Bluetooth: HCI device and connection manager initialized
[4294761.274000] Bluetooth: HCI socket layer initialized
[4294761.301000] Bluetooth: L2CAP ver 2.8
[4294761.301000] Bluetooth: L2CAP socket layer initialized
[4294761.352000] Bluetooth: RFCOMM socket layer initialized
[4294761.352000] Bluetooth: RFCOMM TTY layer initialized
[4294761.352000] Bluetooth: RFCOMM ver 1.7
[4294940.846000] usb 1-1.2: new full speed USB device using uhci_hcd and address 3
[4294941.081000] SCSI subsystem initialized
[4294941.095000] Initializing USB Mass Storage driver...
[4294941.096000] scsi0 : SCSI emulation for USB Mass Storage devices
[4294941.096000] usb-storage: device found at 3
[4294941.096000] usb-storage: waiting for device to settle before scanning
[4294941.097000] usbcore: registered new driver usb-storage
[4294941.097000] USB Mass Storage support registered.
[4294946.100000]   Vendor: 128MB     Model: HardDrive         Rev: 1.11
[4294946.100000]   Type:   Direct-Access                      ANSI SCSI revision: 02
[4294946.106000] usb-storage: device scan complete
[4294946.145000] Driver 'sd' needs updating - please use bus_type methods
[4294946.154000] SCSI device sda: 258048 512-byte hdwr sectors (132 MB)
[4294946.157000] sda: Write Protect is off
[4294946.157000] sda: Mode Sense: 03 00 00 00
[4294946.158000] sda: assuming drive cache: write through
[4294946.233000] SCSI device sda: 258048 512-byte hdwr sectors (132 MB)
[4294946.236000] sda: Write Protect is off
[4294946.236000] sda: Mode Sense: 03 00 00 00
[4294946.236000] sda: assuming drive cache: write through
[4294946.237000]  sda: sda1
[4294946.245000] sd 0:0:0:0: Attached scsi removable disk sda
[4294946.261000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[4294988.663000] sda : READ CAPACITY failed.
[4294988.663000] sda : status=0, message=00, host=7, driver=00 
[4294988.663000] sda : sense not available. 
[4294988.664000] sda: Write Protect is off
[4294988.664000] sda: Mode Sense: 00 00 00 00
[4294988.664000] sda: assuming drive cache: write through
[4294988.664000] usb 1-1.2: USB disconnect, address 3
[4294988.665000]  0:0:0:0: rejecting I/O to dead device
[4294988.666000]  0:0:0:0: rejecting I/O to dead device
[4294988.666000]  0:0:0:0: rejecting I/O to dead device
[4294988.666000]  0:0:0:0: rejecting I/O to dead device
[4294988.666000] sda : READ CAPACITY failed.
[4294988.666000] sda : status=0, message=00, host=1, driver=00 
[4294988.666000] sda : sense not available. 
[4294988.667000]  0:0:0:0: rejecting I/O to dead device
[4294988.667000] sda: Write Protect is off
[4294988.667000] sda: Mode Sense: 00 00 00 00
[4294988.667000] sda: assuming drive cache: write through
[4294988.667000]  sda:<3> 0:0:0:0: rejecting I/O to dead device
[4294988.667000] Buffer I/O error on device sda, logical block 0
[4294988.672000]  0:0:0:0: rejecting I/O to dead device
[4294988.672000] Buffer I/O error on device sda, logical block 0
[4294988.673000]  unable to read partition table